API tools faq
paste
Advertisement
Guest User

lntiq

a guest
Apr 18th, 2011
1,169
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
Bash 11.69 KB | None | 0 0
raw download clone embed print report
  1. ROM VER: 1.0.3
  2. CFG 01
  3. Read EEPROMX
  4.  X
  5.  
  6.  
  7. U-Boot 2010.03 (Apr 07 2011 - 17:31:19)
  8.  
  9. Board: ARV4518PW
  10. SoC: Danube/Twinpass/Vinax-VE V1.5, DDR Speed 166 MHz, CPU Speed 333 MHz
  11. DRAM:  32 MB
  12. Flash:  4 MB
  13. Net:   initializing ar8216 switch... initialized
  14. lq_cpe_eth
  15. Hit any key to stop autoboot:  0
  16. ## Booting kernel from Legacy Image at b0030000 ...
  17.    Image Name:   MIPS OpenWrt Linux-2.6.37.6
  18.    Created:      2011-04-08   2:14:26 UTC
  19.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
  20.    Data Size:    893132 Bytes = 872.2 kB
  21.    Load Address: 80002000
  22.    Entry Point:  80002000
  23.    Verifying Checksum ... OK
  24.    Uncompressing Kernel Image ... OK
  25.  
  26. Starting kernel ...
  27.  
  28. Linux version 2.6.37.6 (victor@ubuntu) (gcc version 4.5.2 (Linaro GCC 4.5-2011.02-0) ) #1 Fri Apr 8 05:14:24 EEST 2011
  29. cpu: 333333334
  30. fpi: 83333333
  31. io: 83250000
  32. SoC: Danube rev1.5 333Mhz
  33. bootconsole [early0] enabled
  34. CPU revision is: 00019641 (MIPS 24Kc)
  35. Determined physical RAM map:
  36.  memory: 02000000 @ 00000000 (usable)
  37. Initrd not found or empty - disabling initrd
  38. Zone PFN ranges:
  39.   Normal   0x00000000 -> 0x00002000
  40. Movable zone start PFN for each node
  41. early_node_map[1] active PFN ranges
  42.     0: 0x00000000 -> 0x00002000
  43. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
  44. Kernel command line: console=ttyS1,115200 rootfstype=squashfs,jffs2 machtype=ARV4518PW
  45. PID hash table entries: 128 (order: -3, 512 bytes)
  46. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  47. Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  48. Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
  49. Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
  50. Writing ErrCtl register=000721a8
  51. Readback ErrCtl register=000721a8
  52. Memory: 29708k/32768k available (2104k kernel code, 3060k reserved, 347k data, 152k init, 0k highmem)
  53. NR_IRQS:256
  54. Calibrating delay loop... 221.69 BogoMIPS (lpj=443392)
  55. pid_max: default: 32768 minimum: 301
  56. Mount-cache hash table entries: 512
  57. NET: Registered protocol family 16
  58. MIPS: machine is ARV4518PW - SMC7908A-ISP, Airties WAV-221
  59. bio: create slab <bio-0> at 0
  60. pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
  61. pci 0000:00:0e.0: BAR 0: set to [mem 0x18000000-0x1800ffff] (PCI address [0x18000000-0x1800ffff])
  62. arch/mips/pci/pci-lantiq.c:pcibios_map_irq[263]14 1
  63. Switching to clocksource MIPS
  64. NET: Registered protocol family 2
  65. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  66. TCP established hash table entries: 1024 (order: 1, 8192 bytes)
  67. TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  68. TCP: Hash tables configured (established 1024 bind 1024)
  69. TCP reno registered
  70. UDP hash table entries: 256 (order: 0, 4096 bytes)
  71. UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  72. NET: Registered protocol family 1
  73. gptu: totally 6 16-bit timers/counters
  74. gptu: misc_register on minor 63
  75. gptu: succeeded to request irq 126
  76. gptu: succeeded to request irq 127
  77. gptu: succeeded to request irq 128
  78. gptu: succeeded to request irq 129
  79. gptu: succeeded to request irq 130
  80. gptu: succeeded to request irq 131
  81. squashfs: version 4.0 (2009/01/31) Phillip Lougher
  82. JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  83. msgmni has been set to 58
  84. io scheduler noop registered
  85. io scheduler deadline registered (default)
  86. lq_asc.0: ttyS0 at MMIO 0x1e100400 (irq = 104) is a lq_asc
  87. lq_asc.1: ttyS1 at MMIO 0x1e100c00 (irq = 112) is a lq_asc
  88. console [ttyS1] enabled, bootconsole disabled
  89. console [ttyS1] enabled, bootconsole disabled
  90. lq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022a8
  91. Amd/Fujitsu Extended Query Table at 0x0040
  92.   Amd/Fujitsu Extended Query version 1.1.
  93. number of CFI chips: 1
  94. Creating 4 MTD partitions on "lq_nor":
  95. 0x000000000000-0x000000020000 : "uboot"
  96. 0x000000020000-0x000000030000 : "uboot_env"
  97. 0x000000030000-0x0000003f0000 : "linux"
  98. Creating 2 MTD partitions on "lq_nor":
  99. 0x000000030000-0x000000110000 : "kernel"
  100. 0x000000110000-0x0000003f0000 : "rootfs"
  101. mtd: partition "rootfs" set to be root filesystem
  102. split_squashfs: no squashfs found in "lq_nor"
  103. 0x0000003f0000-0x000000400000 : "board_config"
  104. eth0: using mac=00:05:59:3B:40:07
  105. lq_mii: probed
  106. eth0: AR8216 switch driver attached.
  107. eth0: attached PHY driver [Atheros AR8216/AR8316] (mii_bus:phy_addr=0:00, irq=-1)
  108. lq_etop: driver loaded!
  109. TCP westwood registered
  110. NET: Registered protocol family 17
  111. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  112. All bugs added by David S. Miller <davem@redhat.com>
  113. JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
  114. VFS: Mounted root (jffs2 filesystem) readonly on device 31:4.
  115. Freeing unused kernel memory: 152k freed
  116. - preinit -
  117. Press the [f] key and hit [enter] to enter failsafe mode
  118. - regular preinit -
  119. - init -
  120.  
  121. Please press Enter to activate this console. device eth0 entered promiscuous mode
  122. br-lan: port 1(eth0) entering forwarding state
  123. br-lan: port 1(eth0) entering forwarding state
  124. SCSI subsystem initialized
  125. usbcore: registered new interface driver usbfs
  126. usbcore: registered new interface driver hub
  127. usbcore: registered new device driver usb
  128. NET: Registered protocol family 8
  129. NET: Registered protocol family 20
  130. PPP generic driver version 2.4.2
  131. ip_tables: (C) 2000-2006 Netfilter Core Team
  132. NET: Registered protocol family 24
  133. nf_conntrack version 0.5.0 (466 buckets, 1864 max)
  134. IFX MEI Version 5.00.00
  135.  
  136. Infineon CPE API Driver version: DSL CPE API V3.24.4.4
  137. Infineon Technologies ATM driver version 1.0.8
  138. Infineon Technologies ATM (A1) firmware version 0.1
  139. ifxmips_atm: ATM init succeed
  140. ath_hal: module license 'Proprietary' taints kernel.
  141. Disabling lock debugging due to kernel taint
  142. ath_hal: 2009-05-08 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, REGOPS_FUNC, XR)
  143. ath_pci: trunk
  144. wlan: trunk
  145. wlan: mac acl policy registered
  146. ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk)
  147. ath_rate_minstrel: look around rate set to 10%
  148. ath_rate_minstrel: EWMA rolloff level set to 75%
  149. ath_rate_minstrel: max segment size in the mrr set to 6000 us
  150. PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
  151. Atheros HAL provided by OpenWrt, DD-WRT and MakSat Technologies
  152. wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
  153. wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
  154. wifi0: H/W encryption support: WEP AES AES_CCM TKIP
  155. ath_pci: wifi0: Atheros 2413: mem=0x18000000, irq=30
  156. dwc_otg: version 2.60a 22-NOV-2006
  157. DWC_otg: Using DMA mode
  158. dwc_otg dwc_otg.0: DWC OTG Controller
  159. dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
  160. dwc_otg dwc_otg.0: irq 62, io mem 0xffffffffbe101000
  161. DWC_otg: Init: Port Power? op_state=1
  162. DWC_otg: Init: Power Port (0)
  163. hub 1-0:1.0: USB hub found
  164. hub 1-0:1.0: 1 port detected
  165. Initializing USB Mass Storage driver...
  166. usbcore: registered new interface driver usb-storage
  167. USB Mass Storage support registered.
  168. usb 1-1: new high speed USB device using dwc_otg and address 2
  169. scsi0 : usb-storage 1-1:1.0
  170. scsi 0:0:0:0: Direct-Access     ADATA    USB Flash Drive  0.00 PQ: 0 ANSI: 2
  171. sd 0:0:0:0: [sda] 7805887 512-byte logical blocks: (3.99 GB/3.72 GiB)
  172. sd 0:0:0:0: [sda] Write Protect is off
  173. sd 0:0:0:0: [sda] Assuming drive cache: write through
  174. sd 0:0:0:0: [sda] Assuming drive cache: write through
  175.  sda: sda1
  176. sd 0:0:0:0: [sda] Assuming drive cache: write through
  177. sd 0:0:0:0: [sda] Attached SCSI removable disk
  178. device ath0 entered promiscuous mode
  179. device ath0 left promiscuous mode
  180. device ath0 entered promiscuous mode
  181. device ath0 left promiscuous mode
  182. device ath0 entered promiscuous mode
  183. device ath0 left promiscuous mode
  184. device ath0 entered promiscuous mode
  185. device ath0 left promiscuous mode
  186.  
  187.  
  188.  
  189. BusyBox v1.18.4 (2011-04-08 05:09:50 EEST) built-in shell (ash)
  190. Enter 'help' for a list of built-in commands.
  191.  
  192.   _______                     ________        __
  193.  |       |.-----.-----.-----.|  |  |  |.----.|  |_
  194.  |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
  195.  |_______||   __|_____|__|__||________||__|  |____|
  196.           |__| W I R E L E S S   F R E E D O M
  197.  ATTITUDE ADJUSTMENT (bleeding edge, r26494) ----------
  198.   * 1/4 oz Vodka      Pour all ingredents into mixing
  199.   * 1/4 oz Gin        tin with ice, strain into glass.
  200.   * 1/4 oz Amaretto
  201.   * 1/4 oz Triple sec
  202.   * 1/4 oz Peach schnapps
  203.   * 1/4 oz Sour mix
  204.   * 1 splash Cranberry juice
  205.  -----------------------------------------------------
  206. root@OpenWrt:/# wifi up
  207. ifconfig: SIOCSIFFLAGS: Cannot assign requested address
  208. ifconfig: SIOCSIFFLAGS: Cannot assign requested address
  209. ifconfig: SIOCSIFFLAGS: Cannot assign requested address
  210. device ath0 entered promiscuous mode
  211. device ath0 left promiscuous mode
  212. device ath0 entered promiscuous mode
  213. device ath0 left promiscuous mode
  214. brctl: bridge br-lan: Invalid argument
  215. brctl: bridge br-lan: File exists
  216. ifconfig: SIOCSIFFLAGS: Cannot assign requested address
  217. device ath0 entered promiscuous mode
  218. device ath0 left promiscuous mode
  219. device ath0 entered promiscuous mode
  220. device ath0 left promiscuous mode
  221. brctl: bridge br-lan: Invalid argument
  222. root@OpenWrt:/# ifconfig -a
  223. ath0      Link encap:Ethernet  HWaddr 81:81:7E:E8:81:81  
  224.           BROADCAST MULTICAST  MTU:1500  Metric:1
  225.           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  226.           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  227.           collisions:0 txqueuelen:0
  228.           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
  229.  
  230. br-lan    Link encap:Ethernet  HWaddr 00:05:59:3B:40:07  
  231.           inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
  232.           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
  233.           RX packets:3 errors:0 dropped:0 overruns:0 frame:0
  234.           TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
  235.           collisions:0 txqueuelen:0
  236.           RX bytes:138 (138.0 B)  TX bytes:402 (402.0 B)
  237.  
  238. eth0      Link encap:Ethernet  HWaddr 00:05:59:3B:40:07  
  239.           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
  240.           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  241.           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  242.           collisions:0 txqueuelen:1000
  243.           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
  244.  
  245. lo        Link encap:Local Loopback  
  246.           inet addr:127.0.0.1  Mask:255.0.0.0
  247.           UP LOOPBACK RUNNING  MTU:16436  Metric:1
  248.           RX packets:6 errors:0 dropped:0 overruns:0 frame:0
  249.           TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
  250.           collisions:0 txqueuelen:0
  251.           RX bytes:402 (402.0 B)  TX bytes:402 (402.0 B)
  252.  
  253. nas0      Link encap:Ethernet  HWaddr 00:00:01:00:00:00  
  254.           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
  255.           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  256.           TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
  257.           collisions:0 txqueuelen:1000
  258.           RX bytes:0 (0.0 B)  TX bytes:504 (504.0 B)
  259.  
  260. wifi0     Link encap:UNSPEC  HWaddr 81-81-7E-E8-81-81-00-47-00-00-00-00-00-00-00-00  
  261.           BROADCAST MULTICAST  MTU:1500  Metric:1
  262.           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  263.           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  264.           collisions:0 txqueuelen:195
  265.           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
  266.           Interrupt:30
  267.  
  268. root@OpenWrt:/# cat /etc/config/wireless
  269. config wifi-device  radio0
  270.         option type     atheros
  271.         option channel  auto
  272.         option macaddr  81:81:7e:e8:81:81
  273.  
  274.         # REMOVE THIS LINE TO ENABLE WIFI:
  275. #       option disabled 1
  276.  
  277. config wifi-iface
  278.         option device   radio0
  279.         option network  lan
  280.         option mode     ap
  281.         option ssid     OpenWrt
  282.         option encryption none
  283.  
  284. root@OpenWrt:/#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!