*** Image flash done *** !

Resetting board...ÿ

CFE version 1.0.37-110.11-1 for BCM96368 (32bit,SP,BE)
Build Date: 2011-04-12 17:31:15 (evan@broadcom_eu)
Copyright (C) 2000-2009 Broadcom Corporation.

Parallel flash device: name MX29GL256EH, id 0x2222 size 32768KB
Total Flash size: 32768K with 256 sectors
Chip ID: BCM6368B2, MIPS: 400MHz
Main Thread: TP0
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000

Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id (0-15)                   : 96368M-1541N
Number of MAC Addresses (1-32)    : 32
Base MAC Address                  : 38:72:c0:d1:8b:9c
PSI Size (1-64) KBytes            : 24
Enable Backup PSI [0|1]           : 0
System Log Size (0-256) KBytes    : 0
Main Thread Number [0|1]          : 0
Serial Number                     : 1173025UXXF-AG013267
Default PSK key                   : Zauu3GqJJZVtWbKQe2uq

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xb8020000) ...
Code Address: 0x80010000, Entry Address: 0x80010000
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80010000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
6 buffers found.
Closing DMA Channels.
Starting program at 0x80010000
[    0.000000] Linux version 3.9.8 (pepe@debian) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r37180) ) #3 Thu Jul 25 13:29:06 CEST 2013
[    0.000000] Detected Broadcom 0x6368 CPU revision b2
[    0.000000] CPU frequency is 400 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 38 GPIOs
[    0.000000] board_bcm963xx: Boot address 0xb8000000
[    0.000000] board_bcm963xx: CFE version: 1.0.37-110.11-1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: 96368M-1541N
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] Memory: 61180k/65536k available (2510k kernel code, 4356k reserved, 689k data, 252k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 512
[    0.044000] NET: Registered protocol family 16
[    0.056000] registering PCI controller with io_map_base unset
[    0.068000] bio: create slab <bio-0> at 0
[    0.072000] PCI host bridge to bus 0000:00
[    0.076000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.080000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.084000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.100000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff]
[    0.104000] Switching to clocksource MIPS
[    0.132000] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08
[    0.196000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[    0.204000] NET: Registered protocol family 2
[    0.212000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.216000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.224000] TCP: Hash tables configured (established 512 bind 512)
[    0.232000] TCP: reno registered
[    0.236000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.240000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.248000] NET: Registered protocol family 1
[    0.256000] audit: initializing netlink socket (disabled)
[    0.260000] type=2000 audit(0.260:1): initialized
[    0.264000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.272000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.284000] msgmni has been set to 119
[    0.288000] io scheduler noop registered
[    0.292000] io scheduler deadline registered (default)
[    0.300000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_Ê[    0.308000] console [ttyS0] enabled, bootconsole disabled
[    0.308000] console [ttyS0] enabled, bootconsole disabled
[    0.320000] bcm63xx-rng bcm63xx-rng: registered RNG driver
[    0.328000] physmap platform flash device: 08000000 at 18000000
[    0.332000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.344000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.348000]   Amd/Fujitsu Extended Query version 1.3.
[    0.356000] number of CFI chips: 1
[    0.360000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1541N
[    0.368000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.372000] bcm63xxpart: Partition 1 is kernel offset 20100 and length 11ff00
[    0.380000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length 1ea0000
[    0.388000] bcm63xxpart: Partition 3 is nvram offset 1fe0000 and length 20000
[    0.396000] bcm63xxpart: Partition 4 is linux offset 20000 and length 1fc0000
[    0.404000] bcm63xxpart: Spare partition is offset 3c0004 and length 1c1fffc
[    0.408000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.416000] Creating 5 MTD partitions on "physmap-flash.0":
[    0.424000] 0x000000000000-0x000000020000 : "CFE"
[    0.428000] 0x000000020100-0x000000140000 : "kernel"
[    0.436000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.448000] 0x000000140000-0x000001fe0000 : "rootfs"
[    0.456000] mtd: partition "rootfs" set to be root filesystem
[    0.464000] mtd: partition "rootfs_data" created automatically, ofs=3C0000, len=1C20000
[    0.472000] 0x0000003c0000-0x000001fe0000 : "rootfs_data"
[    0.480000] 0x000001fe0000-0x000002000000 : "nvram"
[    0.488000] 0x000000020000-0x000001fe0000 : "linux"
[    0.496000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
[    0.544000] b53_common: found switch: BCM63xx, rev 0
[    0.548000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.560000] TCP: cubic registered
[    0.564000] NET: Registered protocol family 17
[    0.568000] 8021q: 802.1Q VLAN Support v1.8
[    0.580000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.592000] Freeing unused kernel memory: 252k freed
procd: Console is alive
[    2.520000] Button Hotplug driver version 0.4.1
[    2.664000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
procd: - preinit -
[    3.088000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port1, 100Mbps, full-duplex
Press the [f] key and hit [enter] to enter failsafe mode
mount_root: jffs2 is not ready - marker found
procd: - early -
procd: - watchdog -
procd: - init -
Please press Enter to activate this console.
[    9.576000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[    9.588000] Backport generated by backports.git backports-20130617-4-ge3220f5
[    9.636000] cfg80211: Calling CRDA to update world regulatory domain
[    9.668000] cfg80211: World regulatory domain updated:
[    9.672000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    9.680000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.688000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    9.696000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    9.704000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.712000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.972000] NET: Registered protocol family 10
[   10.808000] b43-phy0: Broadcom 43222 WLAN found (core revision 16)
[   10.860000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
[   10.896000] Broadcom 43xx driver loaded [ Features: PNL ]
[   11.336000] PPP generic driver version 2.4.2
[   11.460000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.484000] xt_time: kernel timezone is -0000
[   11.496000] NET: Registered protocol family 24
[   11.512000] nf_conntrack version 0.5.0 (959 buckets, 3836 max)
[   15.492000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port1, 100Mbps, full-duplex
[   16.560000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port1, 100Mbps, full-duplex
[   16.572000] device eth0.1 entered promiscuous mode
[   16.576000] device eth0 entered promiscuous mode
[   16.588000] br-lan: port 1(eth0.1) entered forwarding state
[   16.592000] br-lan: port 1(eth0.1) entered forwarding state
[   17.552000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   18.596000] br-lan: port 1(eth0.1) entered forwarding state