Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- OMAP3 beagleboard.org # setenv bootargs console=ttyS2,115200n8 noinitrd root=/de
- v/mmcblk0p2 video=omapfb.mode=dvi:1280x720MR-24@50 init=/init rootfstype=ext3 rw
- rootdelay=1 nohz=off androidboot.console=ttyS2
- OMAP3 beagleboard.org #
- Texas Instruments X-Loader 1.4.2 (Feb 19 2009 - 12:01:24)
- Reading boot sector
- Error: reading boot sector
- Loading u-boot.bin from nand
- U-Boot 2009.11-rc1-00601-g3aa4b51 (Jan 05 2010 - 20:56:38)
- OMAP3530-GP ES3.1, CPU-OPP2 L3-165MHz
- OMAP3 Beagle board + LPDDR/NAND
- I2C: ready
- DRAM: 256 MB
- NAND: 256 MiB
- In: serial
- Out: serial
- Err: serial
- Board revision C4
- Die ID #75840004000000000403a38103014018
- Hit any key to stop autoboot: 0
- mmc1 is available
- reading uImage
- 1850252 bytes read
- ## Booting kernel from Legacy Image at 80000000 ...
- Image Name: Linux-2.6.29-omap1-07176-g57a557
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 1850188 Bytes = 1.8 MB
- Load Address: 80008000
- Entry Point: 80008000
- Verifying Checksum ... OK
- Loading Kernel Image ... OK
- OK
- Starting kernel ...
- Uncompressing Linux.............................................................
- .......................................................... done, booting the ker
- nel.
- Linux version 2.6.29-omap1-07176-g57a5578 (root@ubuntu) (gcc version 4.2.1 (Code
- Sourcery Sourcery G++ Lite 2007q3-51)) #1 Thu May 12 08:31:22 EDT 2011
- CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387f
- CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
- Machine: OMAP3 Beagle Board
- Memory policy: ECC disabled, Data cache writeback
- OMAP3430 ES3.1
- SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000
- Reserving 12582912 bytes SDRAM for VRAM
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
- Kernel command line: console=ttyS2,115200n8 vram=12M omapfb.mode=dvi:1024x768MR-
- 16@60 omapfb.debug=y omapdss.def_disp=dvi root=/dev/mtdblock4 rw rootfstype=jffs
- 2
- Clocking rate (Crystal/DPLL/ARM core): 26.0/332/720 MHz
- GPMC revision 5.0
- IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts
- Total of 96 interrupts on 1 active controller
- OMAP34xx GPIO hardware version 2.5
- PID hash table entries: 1024 (order: 10, 4096 bytes)
- OMAP clockevent source: GPTIMER12 at 32768 Hz
- Console: colour dummy device 80x30
- Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
- Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
- Memory: 128MB 128MB = 256MB total
- Memory: 243200KB available (3368K code, 680K data, 132K init)
- Calibrating delay loop... 713.17 BogoMIPS (lpj=2785280)
- Mount-cache hash table entries: 512
- CPU: Testing write buffer coherency: ok
- net_namespace: 520 bytes
- regulator: core version 0.5
- NET: Registered protocol family 16
- Found NAND on CS0
- Registering NAND on CS0
- OMAP DMA hardware revision 4.0
- bio: create slab <bio-0> at 0
- OMAP DSS rev 2.0
- OMAP DISPC rev 3.0
- OMAP VENC rev 2
- i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
- twl4030: PIH (irq 7) chaining IRQs 368..375
- twl4030: power (irq 373) chaining IRQs 376..383
- twl4030: gpio (irq 368) chaining IRQs 384..401
- regulator: VMMC1: 1850 <--> 3150 mV normal standby
- regulator: VDAC: 1800 mV normal standby
- regulator: VUSB1V5: 1500 <--> 0 mV normal standby
- regulator: VUSB1V8: 1800 <--> 0 mV normal standby
- regulator: VUSB3V1: 3100 <--> 0 mV normal standby
- regulator: VPLL2: 1800 mV normal standby
- regulator: VSIM: 1800 <--> 3000 mV normal standby
- i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
- SCSI subsystem initialized
- twl4030_usb twl4030_usb: Initialized TWL4030 USB module
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- musb_hdrc: version 6.0, musb-dma, host, debug=0
- musb_hdrc: USB Host mode controller at d80ab000 using DMA, IRQ 92
- musb_hdrc musb_hdrc: MUSB HDRC host driver
- musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
- usb usb1: configuration #1 chosen from 1 choice
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- NET: Registered protocol family 2
- IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
- TCP established hash table entries: 8192 (order: 4, 65536 bytes)
- TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
- TCP: Hash tables configured (established 8192 bind 8192)
- TCP reno registered
- NET: Registered protocol family 1
- NetWinder Floating Point Emulator V0.97 (double precision)
- ashmem: initialized
- VFS: Disk quotas dquot_6.5.2
- Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
- msgmni has been set to 475
- alg: No test for stdrng (krng)
- io scheduler noop registered
- io scheduler anticipatory registered (default)
- io scheduler deadline registered
- io scheduler cfq registered
- Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
- serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
- serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
- serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
- console [ttyS2] enabled
- brd: module loaded
- loop: module loaded
- i2c /dev entries driver
- Driver 'sd' needs updating - please use bus_type methods
- omap2-nand driver initializing
- NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bi
- t)
- cmdlinepart partition parsing not available
- Creating 5 MTD partitions on "omap2-nand":
- 0x000000000000-0x000000080000 : "X-Loader"
- 0x000000080000-0x000000260000 : "U-Boot"
- 0x000000260000-0x000000280000 : "U-Boot Env"
- 0x000000280000-0x000000680000 : "Kernel"
- 0x000000680000-0x000010000000 : "File System"
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
- mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
- usbcore: registered new interface driver usbhid
- usbhid: v2.6:USB HID core driver
- logger: created 64K log 'log_main'
- logger: created 256K log 'log_events'
- logger: created 64K log 'log_radio'
- TCP cubic registered
- NET: Registered protocol family 17
- NET: Registered protocol family 15
- RPC: Registered udp transport module.
- RPC: Registered tcp transport module.
- Power Management for TI OMAP3.
- VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
- fbcvt: 1024x768@60: CVT Name - .786M3-R
- clock: clksel_round_rate_div: dpll4_m4_ck target_rate 86400000
- clock: new_div = 5, new_rate = 86400000
- twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:04:02 UTC (946685
- 042)
- VFS: Mounted root (jffs2 filesystem) on device 31:4.
- Freeing init memory: 132K
- Warning: unable to open an initial console.
- Kernel panic - not syncing: No init found. Try passing init= option to kernel.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement