UART Galaxy SL

-----------------------------------------------------------
   Samsung Primitive Bootloader (PBL) v3.0
   Copyright (C) Samsung Electronics Co., Ltd. 2006-2010
-----------------------------------------------------------

[PAM:   ] ++FSR_PAM_Init
[PAM:   ]   OneNAND physical base address       : 0x8000000
[PAM:   ]   OneNAND virtual  base address       : 0x8000000
[PAM:   ]   OneNAND nMID=0xec : nDID=0x50 PageSize = 4KB
[PAM:   ] --FSR_PAM_Init
+n1stVPN       2688
+nPgsPerBlk    64
+n1stVPN       3008
+nPgsPerBlk    64
PBL found bootable SBL: Partition(4).

XXX 1
[BOOT][INI] Target POWERON(Cold) RST
XXX 2
XXX 3
XXX 4=====
XXX 5
XXX 6
[UART] PDA
XXX 7
XXX 8

battery_adc :: 47232
JIG UART ON
check_need_max17040_restart - adc=369000 soc=20, type=0
[BOOT][Battery Normal] Voltage=3690, Real SOC=20, calculate_soc=17, min=14, max=                20

-----------------------------------------------------------
   Samsung Secondary Bootloader (SBL) v3.0
   Copyright (C) Samsung Electronics Co., Ltd. 2006-2010

   Board Name: LATONA REV 08-REAL
   Build On: Jul 22 2011 10:50:27
-----------------------------------------------------------

Re_partition: magic code(0x8080000)
[PAM:   ] ++FSR_PAM_Init
[PAM:   ]   OneNAND physical base address       : 0x8000000
[PAM:   ]   OneNAND virtual  base address       : 0x8000000
[PAM:   ]   OneNAND nMID=0xec : nDID=0x50 PageSize = 4KB
[PAM:   ] --FSR_PAM_Init
fsr_bml_load_partition: pi->nNumOfPartEntry = 13
partitions loading success
board partition information update.. source: 0x0
.Done.
 read 1 units.
==== PARTITION INFORMATION ====
 ID         : IBL+PBL (0x0)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 0
 NO_UNITS   : 1
===============================
 ID         : PIT (0x1)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 1
 NO_UNITS   : 1
===============================
 ID         : EFS (0x14)
 ATTR       : RW STL SLC (0x1101)
 FIRST_UNIT : 2
 NO_UNITS   : 40
===============================
 ID         : SBL (0x3)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 42
 NO_UNITS   : 5
===============================
 ID         : SBL2 (0x4)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 47
 NO_UNITS   : 5
===============================
 ID         : PARAM (0x15)
 ATTR       : RW STL SLC (0x1101)
 FIRST_UNIT : 52
 NO_UNITS   : 30
===============================
 ID         : NORMALBOOT (0x5)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 82
 NO_UNITS   : 32
===============================
 ID         : RECOVERY (0x8)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 114
 NO_UNITS   : 32
===============================
 ID         : SYSTEM (0x16)
 ATTR       : RW STL SLC (0x1101)
 FIRST_UNIT : 146
 NO_UNITS   : 1334
===============================
 ID         : USERDATA (0x17)
 ATTR       : RW STL SLC (0x1101)
 FIRST_UNIT : 1480
 NO_UNITS   : 312
===============================
 ID         : CACHE (0x18)
 ATTR       : RW STL SLC (0x1101)
 FIRST_UNIT : 1792
 NO_UNITS   : 140
===============================
 ID         : FOTA (0x9)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 1932
 NO_UNITS   : 2
===============================
 ID         : MODEM (0xa)
 ATTR       : RO SLC (0x1002)
 FIRST_UNIT : 1934
 NO_UNITS   : 70
===============================
loke_init: j4fs_open success..
load_lfs_parameters valid magic code and version.
LOKE2 (omap charger) : JIG ON
LOKE2 (omap charger) : SET CP JIG ON HIGH
JIG UART ON
[INF] - 1083 - __sbl_board_process_platform/sbl_board.c - g_nBootMode = 0, g_nPo                werUpReason = 5
nps status=0x4321
check_nps_status: nps status : 4321
LOKE2 (charger omap) : read battery adc : 3688
[Battery] loke_check_boot_low_battery SOC=20 BATTERY=3698
JIG UART ON
[LCD] lcd_init() +
[LCD] omap_init_lcd_hw() +
[LCD] enable_lcd_pins() +
[LCD] enable_lcd_pins() -
-----------------Reading I2C value for LCD -------------------------------------                -
remap(Aux3, Aux4), dedicated(Aux3, Aux4), group(Aux3, Aux4)
Sending=0, Receving=0
Sending=0, Receving=0
Sending=1, Receving=1
Sending=9, Receving=9
Sending=2e, Receving=2e
Sending=2e, Receving=2e
-----------------Reading I2C value for LCD -------------------------------------                -
[LCD] omap_init_lcd_hw() 2 : GPIO_LCD_ID1=0, GPIO_LCD_ID2=1
[LCD] read_spi_lcd_id() lcd_spi_id1=0x53
[LCD] read_spi_lcd_id() lcd_spi_id2=0xa9
[LCD] read_spi_lcd_id() lcd_spi_id3=0x60
[LCD] lcd_poweron_sony() +
[LCD] lcd_poweron_sony() --
[LCD] omap_init_lcd_hw() -
[LCD] omap_set_lcd_backlight +

Autoboot (0 seconds) in progress, press any key to stop
.Done.
 read 1 units.
read part info
 id = 0x5
attr = 0x1002
first unin = 0x52
number units = 0x20
pages per unit = 0x40
n1st page = 0x1480, page offset = 0x0, len = 0x1000
read part info
 id = 0x5
attr = 0x1002
first unin = 0x52
number units = 0x20
pages per unit = 0x40
n1st page = 0x1480, page offset = 0x1, len = 0x360000
Kernel  @ 81808000 (3538272 bytes)
read part info
 id = 0x5
attr = 0x1002
first unin = 0x52
number units = 0x20
pages per unit = 0x40
n1st page = 0x1480, page offset = 0x361, len = 0x31e000
Ramdisk @ 82800000 (3268119 bytes)
[LCD] Bootloader __sbl_board_set_current_panel() : current_panel=0

Starting kernel at 0x81808000...

[UART] PDA
[USB] PDA
Uncompressing Linux... done, booting the kernel.