Primary boot with ubi support
Version: 3.20.2   (May 15 2012 - 12:46:09)
Copyright (C) 2011 - 2012 Sagemcom All rights reserved
gpio in: ffb3bbf0
board type: lbv3 1 (00010031)
board frequency: 000001f4
nand ctrl (b909804c) 04050505  19050505
ddr  ctrl (b9100000) f624079e  22123424  c6001842  00000018  0000000d
ddr  ctrl (b9108118) 01004342  00000301

Secondary boot
Version: 3.20.2   (May 15 2012 - 12:46:07)Copyright (C) 2011 - 2012 Sagemcom All rights reserved
board type: 00010031
boot partition size: 08000000
executing raw u-boot

U-Boot 2010.09
Version: 3.20.2-small (May 15 2012 - 12:45:22)
Copyright (C) 2011 - 2012 Sagemcom All rights reserved
board type: 00010031
boot partition size: 08000000
secured bootloader
CPU: IKANOS Fusiv 185-SE Family, Major Revision: 2
DRAM:  128 MiB
NAND:  128 MiB
Creating 1 MTD partitions on "nand0":
0x0000000c0000-0x000008000000 : "mtd=2"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=2"
UBI: MTD device size:            127 MiB
UBI: number of good PEBs:        1018
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    256
UBI: number of internal volumes: 1
UBI: number of user volumes:     7
UBI: available PEBs:             343
UBI: total number of reserved PEBs: 675
UBI: number of PEBs reserved for bad PEB handling: 10
UBI: max/mean erase counter: 50/1
bootenv volume not found
using default environment
Found Atheros Switch AR8327
Net:   emac1
sb3: sb3_sagem_init()
sb3: action: 1007
sb3: sb3_wait_for_magic()
sb3: action: 1002
sb3: sb3_boot( operational )
Volume operational found at volume id 3
read 18030592 bytes from volume 3 to 80400000(buf address)
sb3: image operational has gsdf format
sb3: image operational signature OK
sb3: No pre-boot commands
sb3: setting kernel args
bootm 8041F000
## Booting kernel from Legacy Image at 8041f000 ...
   Image Name:   Ikanos_kernel_2.6.28.8
   Created:      2012-12-11  19:51:06 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    2343311 Bytes = 2.2 MiB
   Load Address: 80010000
   Entry Point:  800142f0
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.28.8 (sah0113@sahwbld03) (gcc version 4.2.4 (SoftAtHome 1.0.7)) #1 PREEMPT Tue Dec 11 20:47:14 CET 2012
argc 15 arg <NULL> env memsize=128
memsize  board_memsize = 128
env memsize=128
initrd_start 80000000
env initrd_start=0xA0000000
initrd_size start 80000000 end 80000000
env initrd_size=0x0
flash_start 0
env flash_start=0x00000000
board_flash_size dff3cfdf
env flash_size=0xDFF3CFDF
env ethaddr=00:01:02:03:04:05
arg[1] root=mtd:rootfs
arg[2] init=/etc/preinit
arg[3] ro
arg[4] rootfstype=squashfs
arg[5] console=ttyS0,115200
arg[6] rootfs_offset=0x0026c000
arg[7] rootfs_size=0x00ec6000
arg[8] mtdparts=nand:128k(fboot),640k(reserved),-(partAll)
arg[9] ubi.mtd=ubi
arg[10] part_main=partAll
arg[11] part_boot=partAll
arg[12] image_ubivol=operational
arg[13] secure
Fusiv MIPS Clock = 500000000 System Clock = 250000000
CPU revision is: 00019554 (MIPS 34Kc)
Determined physical RAM map:
 memory: 07800000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00007800
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00007800
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 30480
Kernel command line: root=mtd:rootfs init=/etc/preinit ro rootfstype=squashfs console=ttyS0,115200 rootfs_offset=0x0026c000 rootfs_size=0x00ec6000 mtdparts=nand:128k(fboot),640k(reserved),-(partAll) ubi.mtd=ubi part_main=partAll part_boot=partAll image_ubivol=operational
UBI image volume: "operational"
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00008400
Readback ErrCtl register=00008400
Initializing VX185 IPC..
PID hash table entries: 512 (order: 9, 2048 bytes)
AHB CLOCK FREQ = 250000000
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 115696k/122880k available (3905k kernel code, 7012k reserved, 936k data, 200k init, 0k highmem)
Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976)
Mount-cache hash table entries: 512
net_namespace: 708 bytes
NET: Registered protocol family 16
Fusiv PCIe RC0 Starting ...
PCIe RC0 Link Up !!!!
registering PCI controller with io_map_base unset
Fusiv PCIe RC1 Starting ...
PCIe RC1 Link Up !!!!
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: PME# supported from D0 D1 D3hot
pci 0000:00:00.0: PME# disabled
pci 0001:01:00.0: PME# supported from D0 D1 D3hot
pci 0001:01:00.0: PME# disabled
Bluetooth: Core ver 2.13
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 3.4 (2008/08/26) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.10)
msgmni has been set to 226
io scheduler noop registered (default)
 Button Module loaded
SoftAtHome Button driver has been initialized
 Led Module loaded
Serial: 8250/16550 driver2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xb9010000 (irq = 28) is a 16450
brd: module loaded
loop: module loaded
PPP generic driver version 2.4.2
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
Driver 'sd' needs updating - please use bus_type methods
ahci ahci: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part
scsi0 : ahci
ata1: SATA max UDMA/133 irq 31
VX185 on-chip NAND FLash Controller Driver, Version 1.1 (c) 2010 Ikanos, Inc.
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00000000-0x000c0000 : "ipl"
0x000c0000-0x08000000 : "ubi"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
Add UBI volume partitions: name=secondaryboot
Add UBI volume partitions: name=uboot
Add UBI volume partitions: name=permanent_param
Add UBI volume partitions: name=operational
Creating 3 MTD partitions on "operational":
0x00000000-0x0001f000 : "auth"
0x00000000-0x0026c000 : "kernel"
0x0026c000-0x01132000 : "rootfs"
Add UBI volume partitions: name=rescue
Add UBI volume partitions: name=user
Add UBI volume partitions: name=ext
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "ubi"
UBI: MTD device size:            127 MiB
UBI: number of good PEBs:        1018
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    256
UBI: number of internal volumes: 1
UBI: number of user volumes:     7
UBI: available PEBs:             343
UBI: total number of reserved PEBs: 675
UBI: number of PEBs reserved for bad PEB handling: 10
UBI: max/mean erase counter: 50/1
UBI: background thread "ubi_bgt0d" started, PID 261
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
VX185 OHCI: Enabling USB clocks and USB PHY reset
fusiv-ohci-hcd fusiv-ohci-hcd.0: Ikanos On-Chip OHCI Host Controller
ata1: SATA link down (SStatus 0 SControl 310)
fusiv-ohci-hcd fusiv-ohci-hcd.0: new USB bus registered, assigned bus number 1
fusiv-ohci-hcd fusiv-ohci-hcd.0: irq 34, io mem 0x19110000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Ikanos On-Chip OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.28.8 ohci_hcd
usb usb1: SerialNumber: ikf71xx ohci
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for cp2101
usbcore: registered new interface driver cp2101
cp2101: v0.07:Silicon Labs CP2101/CP2102 RS232 serial adaptor driver
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: Generic Bluetooth USB driver ver 0.3
usbcore: registered new interface driver btusb
[HAL-BSP]: Load ...
[HAL-BSP]: Manufacturer(Sagemcom) Serial Number(LKXXXXXXXXXXXX)
[HAL-BSP]: Sagem Hardware ProductId(SagemcomFast3965_LB2.8) Version(0.2) Revision(1.0)
[HAL-BSP]: Customer Hardware ProductId(Livebox 3) Version(SG_LB3_1.2.1) Revision(1.0.0)
[HAL-BSP]: Firmware Version(france) Type(Bad Type Firmware)
[HAL-BSP]: Size {Ram -> [Pp(131072) Linux(115868)] Flash ->[Pp(131072)]}
[HAL-BSP]: Ok ...
u32 classifier
    input device check on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1920 buckets, 7680 max)
ctnetlink v0.93: registering with nfnetlink.
Initializing RTSP ALG ...
RTSP ALG initialized successfully.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 200k freed
Failed to execute /etc/preinit.  Attempting defaults...

init started: BusyBox v1.13.3 (2012-12-11 21:09:28 CET)

starting pid 294, tty '': '/etc_ro_fs/init.d/sysinit'
Mounting tmpfs filesystem (/dev) ...
Mounting devpts filesystem (/dev/pts) ...
Mounting proc filesystem ...
Mounting sys filesystem ...
Mounting tmpfs filesystem (/var) ...
Mounting tmpfs filesystem (/var/log) ...
Mounting tmpfs filesystem (/tmp) ...
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
fusiv-ehci-hcd fusiv-ehci-hcd.0: Ikanos On-Chip EHCI Host Controller
fusiv-ehci-hcd fusiv-ehci-hcd.0: new USB bus registered, assigned bus number 2
fusiv-ehci-hcd fusiv-ehci-hcd.0: irq 35, io mem 0x19120000
fusiv-ehci-hcd fusiv-ehci-hcd.0: USB 0.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: Ikanos On-Chip EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.28.8 ehci_hcd
usb usb2: SerialNumber: ikf71xx ehci
> NORMAL BOOT <
JFFS2 write-buffering enabled buffer (2048) erasesize (126976)
jffs2_scan_inode_node(): CRC failed on node at 0x0001ffd8: Read 0xffffffff, calculated 0xc50efb16
> BOOT SYSTEM <
Create /dev/button files
## CV=CONFIG_VERSION_NAME_MAJOR="4.23.27" DB=CONFIG_VERSION_NAME_MAJOR="4.23.27"
cp: cannot stat '/fs/rw/dl/tls/cert0201.pem': No such file or directory
 start rc.sysinit
Mounting other filesystems ...
Switching to RUNLEVEL 1 ...
*********************** Starting script /etc/rc1.d/S01EnableRebootOnCrash at: 4.54 0.50
Enabling Reboot on kernel crash
*********************** Starting script /etc/rc1.d/S01hgwcfg at: 4.60 0.50
*********************** Starting script /etc/rc1.d/S01sysbus at: 4.62 0.50
Starting pcb system bus
*********************** Starting script /etc/rc1.d/S04xdslcfg at: 5.11 0.50
Creating /var/run/ADSL
*********************** Starting script /etc/rc1.d/S05ext at: 5.92 0.50
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 6, name "ext"
UBIFS: file system size:   15745024 bytes (15376 KiB, 15 MiB, 124 LEBs)
UBIFS: journal size:       1015809 bytes (992 KiB, 0 MiB, 6 LEBs)
UBIFS: media format:       4 (latest is 4)
UBIFS: default compressor: LZO
UBIFS: reserved for root:  778132 bytes (759 KiB)
*********************** Starting script /etc/rc1.d/S05hardware at: 6.07 0.50
pwrmgmtdrv_lkm: module license 'proprietary' taints kernel.
Power Management driver registered with Major number: 250
fusiv library initializing...
Buffer Copy Through DMA is enabled

fusiv library initialized SUCCESSFULLY...
Timers are getting initalizedTimers are initilized SUCCESSFULLY...

AP2AP fastpath initialized SUCCESSFULLY
 Buffer Manager is initializing...vvangala_18:38_22May11
initLmemFtSpace  128Num of LMEM descriptors initialized = 822
apInitOperation: Operation table initialized Succesfully...(0xc02b0154, 48)
Load into BM APU Successful !!!

*****Clock :0xffffffc
periApDriverInit: done *******LOAD firmware to AP:PERI_ID result:0Load into PERI_AP APU Successful !!!

eth0: Netpro Ethernet found, irq:36
SraPort_initializePort: apId 1
eth0 interface configured in GMII mode
eth1: Netpro Ethernet found, irq:37
SraPort_initializePort: apId 2

Ethernet Driver is initialized SUCCESSFULLY

CLAPs is initializing...
Load into CL_AP 9 APU Successful, irq: 39 !!!

Load into CL_AP 10 APU Successful, irq: 40 !!!


ACL-AP is initializing...
ACL major allocated is 201
Initializing 4 AP for ACL while SPA_ID=4
The pConfig->ipc.cpuQueueSpec[cnt].pQueue is 6a74e00, NumEntries=100

The pConfig->ipc.cpuQueueSpec[cnt].pQueue is 6a74c00, NumEntries=100

The pConfig->ipc.cpuQueueSpec[cnt].pQueue is 6a74a00, NumEntries=100

The pConfig->ipc.cpuQueueSpec[cnt].pQueue is 6a74800, NumEntries=100

Configuring host ACL Layer-2 ruleset (128/4 Rules/Intf)

Configuring host ACL Layer-3 ruleset (128/4 Rules/Intf)
Load into ACL_AP APU Successful !!!

Need to run mknod ...
bmedrv_init: Registered BME device with Major number 249
bmedrv_init: Region 0xaf800000 - 0xafffffff allocated successfully
BME Driver has been loaded SUCCESSFULLY
ADSL Link Tracker Module Initialized

SAGEMCOM Modified SPI Driver is initialized Successfully...
SSD1305: Framebuffer driver for Solomon Systech's "SSD1305" OLED screen controller on Sagemcom's RGWs (v0.3.4-sah)
***********************************************************
Using: Software Build(voice_2_6  : V2 VOICE ARCHITECTURE)
***********************************************************
 NTR DIV Factor = 55  NTR Frame sync width is set to [4] SCLK cycles of 4.096 MHz  Power down, Power Up DSPs....Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2

 Registering Call Back Handlers
 Configuring SCLK and FS as external, using NTR Clock/FS  DSP CLock Assigned:255 DSP SPORT Control Reg  Assigned:820fADSP218x DOWNLOAD DONE !!!!
DSP Ver No:1.1
ADSP218x DOWNLOAD DONE !!!!
DSP Ver No:1.1

 Initializing SLIC and VOICE Wait Queues

 Initializing Voice
 Fusiv Chipset = VX185, ChipID = 30200  Issuing HW Reset to SLIC using GPIO3  Issuing HW Reset to SLIC using GPIO4  SPI BAUD for SLIC Device: 0x10
 Fusiv Chipset = VX185, ChipID = 30200  Issuing HW Reset to SLIC using GPIO3  Issuing HW Reset to SLIC using GPIO4 Assuming SLIC card as SILABS Si3217
Initializing SLICs
 Silabs Si3217 code
Country use for SLIC FRANCE
port 0 is Si32176
LOAD Si3217 PATCH for Rev B
Si3217 patch version 0X09292009
Patch loaded successfully
PATCH Ret=0
MDAC Calibration for channel
other Calibration
ZCAL Calibration
 Silabs Si3217 code
Country use for SLIC FRANCE
 ERROR SLIC IS NOT A SI3217x read 7 slicHandlers.fxoChipType:16
 Silabs FXO - Si3050 FXO Initialized Successfully
Activate SLICs FXS => 2 FXO=>1
 Issuing HW Reset to DECT using GPIO2  SPI BAUD for DECT Device:0xfa

 Enable IRQ for DSP

 Enable IRQ for DSP

 Enable IRQ for DSPDVE

 Enable IRQ for DSP DEC
 MAX_SLIC_CHANNELS = 5 NUM_FXO_CHANNELS = 1
 DSP System Initialized Successfully
Starting Kernel RTP Thread
RTP Kernel Thread Started Found Atheros 8327 switch hardware
Atheros 83xx switch registered to ethernet port eth0
IGMP Snoop Module inserted successfully
WRITE Switch Register[0x600]:Value[0x5e7ffffa]
WRITE Switch Register[0x604]:Value[0x801f0100]
WRITE Switch Register[0x608]:Value[0x0000010f]
WRITE Switch Register[0x60c]:Value[0x80000002]
*********************** Starting script /etc/rc1.d/S05wlhw at: 23.14 0.62
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, AR5416_ISR_READ_CLEAR_SUPPORT, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_pci: 9.2.0_U9.915 (Atheros/multi-bss)
PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
dfs_attach: use DFS enhancements
DFS min filter rssiThresh = 15
DFS max pulse dur = 151 ticks
ath_get_caps[4952] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[4927] tx chainmask mismatch actual 3 sc_chainmak 0
wifi0: Atheros 9380: mem=0x1a000000, irq=32 hw_base=0xba000000
PCI: Enabling device 0001:01:00.0 (0000 -> 0002)
__ath_attach: Set global_scn[1]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
dfs_attach: use DFS enhancements
DFS min filter rssiThresh = 15
DFS max pulse dur = 151 ticks
ath_get_caps[4952] rx chainmask mismatch actual 7 sc_chainmak 0
ath_get_caps[4927] tx chainmask mismatch actual 7 sc_chainmak 0
wifi1: Atheros 9580: mem=0x1b000000, irq=33 hw_base=0xbb000000
*********************** Starting script /etc/rc1.d/S10netmodeconfig1 at: 26.01 0.62
*********************** Starting script /etc/rc1.d/S15syslogd at: 31.17 0.62
*********************** Starting script /etc/rc1.d/S16usermngt at: 31.20 0.62
*********************** Starting script /etc/rc1.d/S20nemo-core at: 31.46 0.62
*********************** Starting script /etc/rc1.d/S20network at: 32.40 0.62
Hostname configuration : LIVEBOX
*********************** Starting script /etc/rc1.d/S21ftnetconfig at: 32.47 0.62
*********************** Starting script /etc/rc1.d/S21geniodb at: 32.49 0.62
Loading geniodb kernel module...
 Thomson geniodb driver: Loading ...
 Thomson geniodb driver: Loading finished with SUCCESS
*********************** Starting script /etc/rc1.d/S21nemo-extensions1 at: 32.59 0.62
*********************** Starting script /etc/rc1.d/S21netdev at: 32.86 0.62
NeMo.loadModule() done
*********************** Starting script /etc/rc1.d/S22firewall at: 33.05 0.62
*********************** Starting script /etc/rc1.d/S22gatewayd at: 35.10 0.62
gatewayd start ...
hco_upgrade_get_partition_info part_type(PART_TYPE_NORM) bufflen(64)hco_upgrade_get_partition_info: Version Len(9) Version String(4.23.27.1)hco_upgrade_get_partition_info success version(4.23.27.1)hco_upgrade_get_partition_info part_type(PART_TYPE_RESC) bufflen(64)hco_upgrade_get_partition_info: Version Len(9) Version String(4.23.27.1)hco_upgrade_get_partition_info success version(4.23.27.1)End of initialisation*********************** Starting script /etc/rc1.d/S22screen at: 40.20 4.69
Starting screen plugin
*********************** Starting script /etc/rc1.d/S23nemo-clients at: 40.77 4.69
device eth0 entered promiscuous mode
bridge: topology change detected, propagating
bridge: port 1(eth0) entering forwarding state
device bridge entered promiscuous mode
device vlan_iptv1 entered promiscuous mode
device eth1 entered promiscuous mode
bridge_viptv: topology change detected, propagating
bridge_viptv: port 1(vlan_iptv1) entering forwarding state
device vlan_iptv2 entered promiscuous mode
bridge_viptv: topology change detected, propagating
bridge_viptv: port 2(vlan_iptv2) entering forwarding state
*********************** Starting script /etc/rc1.d/S24resolvd at: 42.09 4.69
Resolv daemon start ...
*********************** Starting script /etc/rc1.d/S25dnsplugin at: 42.23 4.69
dnsmasq already stopped...
dnsmasq start ...
*********************** Starting script /etc/rc1.d/S28dhcpv6server at: 42.66 4.69
*********************** Starting script /etc/rc1.d/S40nlplugd at: 42.82 4.69
nlplugd start ...
Initializing.Starting netlink pluginDaemonize netlink plugin*********************** Starting script /etc/rc1.d/S420fuse at: 42.90 4.69
Fuse filesystem already available.
Mounting fuse control filesystem.
*********************** Starting script /etc/rc1.d/S42usb-host at: 42.96 4.69
Starting usbmgr
*********************** Starting script /etc/rc1.d/S44igmpsnooping at: 43.09 4.69
IGMP Snooping is enabled on device bridge

Group added successfully

*********************** Starting script /etc/rc1.d/S45dhccd at: 43.58 4.69
dhccd start ...
Daemonize dhccd*********************** Starting script /etc/rc1.d/S50deviceinfo at: 43.70 4.69
Starting deviceinfo plugin
*********************** Starting script /etc/rc1.d/S50wld_ath at: 43.76 4.69
wlan_vap_create : enter. devhandle=0x85a1c380, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x85a1c380, opmode=IEEE80211_M_HOSTAP, flags=0x1.
*********************** Starting script /etc/rc1.d/SVAP device wl0 created
70stopload at: 44.20 4.69
device wl0 entered promiscuous mode
Group added successfully

Wait until configuration load reachwlan_vap_create : enter. devhandle=0x85a1c380, opmode=IEEE80211_M_HOSTAP, flags=0x1
es phase 10 (now -1)
wlan_vap_create : exit. devhandle=0x85a1c380, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device wl2 created
wlan_vap_create : enter. devhandle=0x85048380, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x85048380, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device wl1 created
device wl1 entered promiscuous mode
Group added successfully

appbox: start loading after [  9074ms ]Wait until configuration load reaches phase 10 (now 4)
appbox: end loading
 DES SSID SET=Livebox-AAAA

 DES SSID SET=orange

 DES SSID SET=Livebox-AAAA
*********************** Starting script /etc/rc1.d/S71mbusmap at: 46.37 5.86
Starting mbus mapper
PPP
PPP.Scan
*********************** Starting script /etc/rc1.d/S71raplugin at: 46.67 5.86
Start Router Advertisement Plugin
*********************** Starting script /etc/rc1.d/S71start_wlan at: 46.85 5.86
*********************** Starting script /etc/rc1.d/S72nemo-extensions2 at: 46.87 5.86
*********************** Starting script /etc/rc1.d/S72netmodeconfig2 at: 47.13 5.86
Setting new VOWEXT parameters
VOW enabled features:
fair_queuing: 0
retry_delay_red 0,
buffer reordering 0
enhanced_rate_control_and_aggr 0
Setting new VOWEXT parameters
VOW enabled features:
fair_queuing: 0
retry_delay_red 0,
buffer reordering 0
enhanced_rate_control_and_aggr 0
Setting new VOWEXT parameters
VOW enabled features:
fair_queuing: 1
retry_delay_red 0,
buffer reordering 0
enhanced_rate_control_and_aggr 0
 ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
 ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
 DEVICE IS DOWN ifname=wl0
 DEVICE IS DOWN ifname=wl0
 DEVICE IS DOWN ifname=wl1
 DEVICE IS DOWN ifname=wl1
bridge: topology change detected, propagating
bridge: port 2(wl0) entering forwarding state
bridge: topology change detected, propagating
bridge: port 3(wl1) entering forwarding state
*********************** Starting script /etc/rc1.d/S72www-backend at: 52.93 6.21
Starting www-backend plugin
*********************** Starting script /etc/rc1.d/S73eventmanager at: 53.08 6.21
Starting pcb eventmanager
*********************** Starting script /etc/rc1.d/S73httpd at: 53.16 6.21
Starting http server
Starting httpd watchdog
*********************** Starting script /etc/rc1.d/S74devdiscd at: 53.68 6.21
warning: `httpd' uses 32-bit capabilities (legacy support in use)
*********************** Starting script /etc/rc1.d/S75captiveportal at: 54.48 6.21
*********************** Starting script /etc/rc1.d/S76pwrledstop at: 55.15 6.21
pwrledstart stop ...
*********************** Starting script /etc/rc1.d/S78dyndns at: 55.30 6.21
Starting dyndns plug-in
*********************** Starting script /etc/rc1.d/S78openntpd_plugin at: 55.55 6.21
Starting openntpd plugin
*********************** Starting script /etc/rc1.d/S80telnetd at: 55.85 6.21
telnetd start ...
open telnet in the firewall ...
*********************** Starting script /etc/rc1.d/S81phonebook_plugin at: 55.90 6.21
Starting phonebok_plugin plugin
bridge: port 1(eth0) entering forwarding state
*********************** Starting script /etc/rc1.d/S81voicecfgload at: 56.08 6.21
Restoring voice datamodel from file
 Done! Configuration restored using the backup configuration
*********************** Starting script /etc/rc1.d/S82voipapp at: 56.20 6.21
Function ieee80211_acs_find_best_11na_centerchan best 5G channel is 100
Enabled radar detection on channel 5500
ath_chan_set: start DFS WAIT period on channel 5500
bridge_viptv: port 1(vlan_iptv1) entering forwarding state
bridge_viptv: port 2(vlan_iptv2) entering forwarding state
VoiceCmdVoicePlugin
VoiceCmdVoicePlugin.Plugin
*********************** Starting script /etc/rc1.d/S83fxs at: 58.06 6.21
Start Ikanos fxs/fxo/dsp plugin...
*********************** Starting script /etc/rc1.d/S85scheduler at: 58.11 6.21
Starting Scheduler plug-in
*********************** Starting script /etc/rc1.d/S86udpechoconfig at: 58.31 6.21
Starting UDPEchoPlusServer plug-in
*********************** Starting script /etc/rc1.d/S87usbhosts at: 58.67 6.21
Starting usbhosts plug-in
*********************** Starting script /etc/rc1.d/S89usb_modeswitch_boot at: 58.99 6.21
*********************** Starting script /etc/rc1.d/S90dlnaserver at: 59.37 6.21
*********************** Starting script /etc/rc1.d/S90tod at: 59.61 6.21
Starting ToD plug-in
*********************** Starting script /etc/rc1.d/S90wakeonlan at: 59.78 6.21
Starting WakeOnLan plug-in
*********************** Starting script /etc/rc1.d/S90wlanscheduler at: 59.86 6.21
Starting WLanScheduler plug-in
*********************** Starting script /etc/rc1.d/S91cups at: 60.03 6.21
Creating /dev/usb/lp0
*********************** Starting script /etc/rc1.d/S97igd at: 60.34 6.21
Starting pcb igd mapper
*********************** Starting script /etc/rc1.d/S98avahi at: 61.39 6.21
*********************** Starting script /etc/rc1.d/S98cwmp at: 61.63 6.21
Starting cwmp plug-in
Starting ippingdiagnostics plug-in
Starting cwmpd
*********************** Starting script /etc/rc1.d/S98remoteaccess at: 62.33 6.21
Starting remote access plug-in
*********************** Starting script /etc/rc1.d/S98upgraded at: 62.58 6.21
Starting upgraded plugin
Starting upgraded
upgraded started
*********************** Starting script /etc/rc1.d/S98voipaad at: 62.92 6.21
Starting voipaad plugin
*********************** Starting script /etc/rc1.d/S98wifi-community at: 63.15 6.21
Starting Wifi Community plug-in
*********************** Starting script /etc/rc1.d/S99audiphone at: 63.75 6.21
Starting audiphone_client
Starting audiphone_plugin
*********************** Starting script /etc/rc1.d/S99cifscl at: 64.00 6.21
*********************** Starting script /etc/rc1.d/S99conmon at: 64.19 6.21
Starting Connectivity Monitor (ConMon) plug-in
*********************** Starting script /etc/rc1.d/S99dummy_ep at: 64.32 6.21
Start dummy endpointplugin ...
*********************** Starting script /etc/rc1.d/S99gwmonstart at: 64.40 6.21
Starting gwmonit
*********************** Starting script /etc/rc1.d/S99printkoff at: 64.52 6.21
Setting printk off
*********************** Starting script /etc/rc1.d/S99rdect at: 64.60 6.21
Start Dspgroup SPI dect plugin
cmbs_api_Init: data pump is started. ThreadId:0
cmbs_api_Init: call back thread started. ThreadId:0
cmbs_api_Init: Media is TDM interface
*********************** Starting script /etc/rc1.d/S99saveflush at: 65.12 6.21
*********************** Starting script /etc/rc1.d/S99storage at: 65.17 6.21
*********************** Starting script /etc/rc1.d/S99upload_client at: 66.38 6.21
Starting upload client
*********************** Starting script /etc/rc1.d/S99upnp-igd at: 66.57 6.21
Create UPnPd target directory
Start upnp-igd plugin
*********************** Starting script /etc/rc1.d/S99upnpdiscd_plugin at: 67.02 6.21
Starting upnp discovery plugin
*********************** Starting script /etc/rc1.d/S99wolproxy at: 67.08 6.21
Starting Wake On LAN Proxy plug-in
Sysinit done.

starting pid 1701, tty '': '/etc_ro_fs/init.d/rc.sysinit'
Mounting other filesystems ...
Switching to RUNLEVEL 1 ...
Sysinit done.

Please press Enter to activate this console. Starting to monitor the gatewayd process...