Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- iw.list
- ```
- Wiphy phy0
- max # scan SSIDs: 20
- max scan IEs length: 425 bytes
- max # sched scan SSIDs: 20
- max # match sets: 11
- Retry short limit: 7
- Retry long limit: 4
- Coverage class: 0 (up to 0m)
- Device supports RSN-IBSS.
- Device supports AP-side u-APSD.
- Supported Ciphers:
- * WEP40 (00-0f-ac:1)
- * WEP104 (00-0f-ac:5)
- * TKIP (00-0f-ac:2)
- * CCMP (00-0f-ac:4)
- * 00-0f-ac:10
- * GCMP (00-0f-ac:8)
- * 00-0f-ac:9
- * CMAC (00-0f-ac:6)
- * 00-0f-ac:13
- * 00-0f-ac:11
- * 00-0f-ac:12
- Available Antennas: TX 0 RX 0
- Supported interface modes:
- * IBSS
- * managed
- * AP
- * AP/VLAN
- * monitor
- * P2P-client
- * P2P-GO
- * P2P-device
- Band 1:
- Capabilities: 0x11e2
- HT20/HT40
- Static SM Power Save
- RX HT20 SGI
- RX HT40 SGI
- TX STBC
- RX STBC 1-stream
- Max AMSDU length: 3839 bytes
- DSSS/CCK HT40
- Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
- Minimum RX AMPDU time spacing: 4 usec (0x05)
- HT Max RX data rate: 300 Mbps
- HT TX/RX MCS rate indexes supported: 0-15
- Bitrates (non-HT):
- * 1.0 Mbps
- * 2.0 Mbps (short preamble supported)
- * 5.5 Mbps (short preamble supported)
- * 11.0 Mbps (short preamble supported)
- * 6.0 Mbps
- * 9.0 Mbps
- * 12.0 Mbps
- * 18.0 Mbps
- * 24.0 Mbps
- * 36.0 Mbps
- * 48.0 Mbps
- * 54.0 Mbps
- Frequencies:
- * 2412 MHz [1] (22.0 dBm)
- * 2417 MHz [2] (22.0 dBm)
- * 2422 MHz [3] (22.0 dBm)
- * 2427 MHz [4] (22.0 dBm)
- * 2432 MHz [5] (22.0 dBm)
- * 2437 MHz [6] (22.0 dBm)
- * 2442 MHz [7] (22.0 dBm)
- * 2447 MHz [8] (22.0 dBm)
- * 2452 MHz [9] (22.0 dBm)
- * 2457 MHz [10] (22.0 dBm)
- * 2462 MHz [11] (22.0 dBm)
- * 2467 MHz [12] (disabled)
- * 2472 MHz [13] (disabled)
- Band 2:
- Capabilities: 0x11e2
- HT20/HT40
- Static SM Power Save
- RX HT20 SGI
- RX HT40 SGI
- TX STBC
- RX STBC 1-stream
- Max AMSDU length: 3839 bytes
- DSSS/CCK HT40
- Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
- Minimum RX AMPDU time spacing: 4 usec (0x05)
- HT Max RX data rate: 300 Mbps
- HT TX/RX MCS rate indexes supported: 0-15
- VHT Capabilities (0x038071a0):
- Max MPDU length: 3895
- Supported Channel Width: neither 160 nor 80+80
- short GI (80 MHz)
- TX STBC
- SU Beamformee
- VHT RX MCS set:
- 1 streams: MCS 0-9
- 2 streams: MCS 0-9
- 3 streams: not supported
- 4 streams: not supported
- 5 streams: not supported
- 6 streams: not supported
- 7 streams: not supported
- 8 streams: not supported
- VHT RX highest supported: 0 Mbps
- VHT TX MCS set:
- 1 streams: MCS 0-9
- 2 streams: MCS 0-9
- 3 streams: not supported
- 4 streams: not supported
- 5 streams: not supported
- 6 streams: not supported
- 7 streams: not supported
- 8 streams: not supported
- VHT TX highest supported: 0 Mbps
- Bitrates (non-HT):
- * 6.0 Mbps
- * 9.0 Mbps
- * 12.0 Mbps
- * 18.0 Mbps
- * 24.0 Mbps
- * 36.0 Mbps
- * 48.0 Mbps
- * 54.0 Mbps
- Frequencies:
- * 5180 MHz [36] (17.0 dBm) (no IR)
- * 5200 MHz [40] (17.0 dBm) (no IR)
- * 5220 MHz [44] (17.0 dBm) (no IR)
- * 5240 MHz [48] (17.0 dBm) (no IR)
- * 5260 MHz [52] (22.0 dBm) (no IR, radar detection)
- DFS state: usable (for 988 sec)
- DFS CAC time: 60000 ms
- * 5280 MHz [56] (22.0 dBm) (no IR, radar detection)
- DFS state: usable (for 988 sec)
- DFS CAC time: 60000 ms
- * 5300 MHz [60] (22.0 dBm) (no IR, radar detection)
- DFS state: usable (for 988 sec)
- DFS CAC time: 60000 ms
- * 5320 MHz [64] (22.0 dBm) (no IR, radar detection)
- DFS state: usable (for 988 sec)
- DFS CAC time: 60000 ms
- * 5500 MHz [100] (22.0 dBm) (no IR, radar detection)
- DFS state: usable (for 988 sec)
- DFS CAC time: 60000 ms
- * 5520 MHz [104] (22.0 dBm) (no IR, radar detection)
- DFS state: usable (for 988 sec)
- DFS CAC time: 60000 ms
- * 5540 MHz [108] (22.0 dBm) (no IR, radar detection)
- DFS state: usable (for 988 sec)
- DFS CAC time: 60000 ms
- * 5560 MHz [112] (22.0 dBm) (no IR, radar detection)
- DFS state: usable (for 988 sec)
- DFS CAC time: 60000 ms
- * 5580 MHz [116] (22.0 dBm) (no IR, radar detection)
- DFS state: usable (for 988 sec)
- DFS CAC time: 60000 ms
- * 5600 MHz [120] (disabled)
- * 5620 MHz [124] (disabled)
- * 5640 MHz [128] (disabled)
- * 5660 MHz [132] (22.0 dBm) (no IR, radar detection)
- DFS state: usable (for 988 sec)
- DFS CAC time: 60000 ms
- * 5680 MHz [136] (22.0 dBm) (no IR, radar detection)
- DFS state: usable (for 988 sec)
- DFS CAC time: 60000 ms
- * 5700 MHz [140] (22.0 dBm) (no IR, radar detection)
- DFS state: usable (for 988 sec)
- DFS CAC time: 60000 ms
- * 5720 MHz [144] (disabled)
- * 5745 MHz [149] (22.0 dBm) (no IR)
- * 5765 MHz [153] (22.0 dBm) (no IR)
- * 5785 MHz [157] (22.0 dBm) (no IR)
- * 5805 MHz [161] (22.0 dBm) (no IR)
- * 5825 MHz [165] (22.0 dBm) (no IR)
- Supported commands:
- * new_interface
- * set_interface
- * new_key
- * start_ap
- * new_station
- * new_mpath
- * set_mesh_config
- * set_bss
- * authenticate
- * associate
- * deauthenticate
- * disassociate
- * join_ibss
- * join_mesh
- * remain_on_channel
- * set_tx_bitrate_mask
- * frame
- * frame_wait_cancel
- * set_wiphy_netns
- * set_channel
- * set_wds_peer
- * start_sched_scan
- * probe_client
- * set_noack_map
- * register_beacons
- * start_p2p_device
- * set_mcast_rate
- * channel_switch
- * set_qos_map
- * add_tx_ts
- * connect
- * disconnect
- Supported TX frame types:
- * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0
- 0xc0 0xd0 0xe0 0xf0
- * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0
- 0xb0 0xc0 0xd0 0xe0 0xf0
- * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0
- 0xc0 0xd0 0xe0 0xf0
- * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0
- 0xb0 0xc0 0xd0 0xe0 0xf0
- * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0
- 0xb0 0xc0 0xd0 0xe0 0xf0
- * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0
- 0xb0 0xc0 0xd0 0xe0 0xf0
- * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0
- 0xb0 0xc0 0xd0 0xe0 0xf0
- * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0
- 0xb0 0xc0 0xd0 0xe0 0xf0
- Supported RX frame types:
- * IBSS: 0x40 0xb0 0xc0 0xd0
- * managed: 0x40 0xd0
- * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- * mesh point: 0xb0 0xc0 0xd0
- * P2P-client: 0x40 0xd0
- * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- * P2P-device: 0x40 0xd0
- WoWLAN support:
- * wake up on disconnect
- * wake up on magic packet
- * wake up on pattern match, up to 20 patterns of 16-128 bytes,
- maximum packet offset 0 bytes
- * can do GTK rekeying
- * wake up on GTK rekey failure
- * wake up on EAP identity request
- * wake up on 4-way handshake
- * wake up on rfkill release
- * wake up on network detection, up to 11 match sets
- * wake up on TCP connection
- software interface modes (can always be added):
- * AP/VLAN
- * monitor
- valid interface combinations:
- * #{ managed } <= 1, #{ AP, P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1,
- total <= 3, #channels <= 2
- HT Capability overrides:
- * MCS: ff ff ff ff ff ff ff ff ff ff
- * maximum A-MSDU length
- * supported channel width
- * short GI for 40 MHz
- * max A-MPDU length exponent
- * min MPDU start spacing
- Device supports TX status socket option.
- Device supports HT-IBSS.
- Device supports SAE with AUTHENTICATE command
- Device supports low priority scan.
- Device supports scan flush.
- Device supports per-vif TX power setting
- P2P GO supports CT window setting
- P2P GO supports opportunistic powersave setting
- Driver supports a userspace MPM
- Device supports static SMPS
- Device supports dynamic SMPS
- Device supports WMM-AC admission (TSPECs)
- Device supports configuring vdev MAC-addr on create.
- ```
- hostapd.log
- ```
- random: Trying to read entropy from /dev/random
- Configuration file: /etc/hostapd/hostapd.conf
- ctrl_interface_group=0
- rfkill: initial event: idx=0 type=2 op=0 soft=0 hard=0
- rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0
- nl80211: Supported cipher 00-0f-ac:1
- nl80211: Supported cipher 00-0f-ac:5
- nl80211: Supported cipher 00-0f-ac:2
- nl80211: Supported cipher 00-0f-ac:4
- nl80211: Supported cipher 00-0f-ac:10
- nl80211: Supported cipher 00-0f-ac:8
- nl80211: Supported cipher 00-0f-ac:9
- nl80211: Supported cipher 00-0f-ac:6
- nl80211: Supported cipher 00-0f-ac:13
- nl80211: Supported cipher 00-0f-ac:11
- nl80211: Supported cipher 00-0f-ac:12
- nl80211: Using driver-based off-channel TX
- nl80211: Use separate P2P group interface (driver advertised support)
- nl80211: Enable multi-channel concurrent (driver advertised support)
- nl80211: use P2P_DEVICE support
- nl80211: interface wlp4s0 in phy phy0
- nl80211: Set mode ifindex 4 iftype 3 (AP)
- nl80211: Setup AP(wlp4s0) - device_ap_sme=0 use_monitor=0
- nl80211: Subscribe to mgmt frames with AP handle 0xcd6260
- nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH)
- nl_handle=0xcd6260 match=
- nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ)
- nl_handle=0xcd6260 match=
- nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ)
- nl_handle=0xcd6260 match=
- nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC)
- nl_handle=0xcd6260 match=
- nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH)
- nl_handle=0xcd6260 match=
- nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
- nl_handle=0xcd6260 match=
- nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ)
- nl_handle=0xcd6260 match=
- nl80211: Add own interface ifindex 4
- nl80211: if_indices[16]: 4
- phy: phy0
- BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
- wlp4s0: interface state UNINITIALIZED->COUNTRY_UPDATE
- Previous country code US, new country code US
- nl80211: Regulatory information - country=US (DFS-FCC)
- nl80211: 2402-2472 @ 40 MHz 30 mBm
- nl80211: 5170-5250 @ 80 MHz 17 mBm
- nl80211: 5250-5330 @ 80 MHz 23 mBm (DFS)
- nl80211: 5490-5600 @ 80 MHz 23 mBm (DFS)
- nl80211: 5650-5710 @ 40 MHz 23 mBm (DFS)
- nl80211: 5735-5835 @ 80 MHz 30 mBm
- nl80211: 57240-63720 @ 2160 MHz 40 mBm
- nl80211: Added 802.11b mode based on 802.11g information
- Disable HT capability [DSSS_CCK-40] on 5 GHz band
- hw vht capab: 0x38071a0, conf vht capab: 0x10a0
- wlp4s0: interface state COUNTRY_UPDATE->HT_SCAN
- Scan for neighboring BSSes prior to enabling 40 MHz channel
- 40 MHz affected channel range: [5650,5690] MHz
- wlp4s0: nl80211: scan request
- Scan requested (ret=0) - scan timeout 10 seconds
- Interface initialization will be completed in a callback
- ctrl_iface not configured!
- random: Got 20/20 bytes from /dev/random
- RTM_NEWLINK: ifi_index=4 ifname=wlp4s0 operstate=2 linkmode=0
- ifi_family=0 ifi_flags=0x1002 ()
- nl80211: Ignore interface down event since interface wlp4s0 is up
- RTM_NEWLINK: ifi_index=4 ifname=wlp4s0 operstate=2 linkmode=0
- ifi_family=0 ifi_flags=0x1003 ([UP])
- nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlp4s0
- wlp4s0: nl80211: Scan trigger
- wlp4s0: Event SCAN_STARTED (47) received
- Unknown event 47
- RTM_NEWLINK: ifi_index=4 ifname=wlp4s0 wext ifi_family=0
- ifi_flags=0x1003 ([UP])
- nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlp4s0
- wlp4s0: nl80211: New scan results available
- nl80211: Scan included frequencies: 5660 5680
- wlp4s0: Event SCAN_RESULTS (3) received
- nl80211: Received scan results (0 BSSes)
- HT40: control channel: 132 secondary channel: 136
- Completing interface initialization
- Mode: IEEE 802.11a Channel: 132 Frequency: 5660 MHz
- DFS 0 channels required radar detection
- Could not set channel for kernel driver
- Interface initialization failed
- wlp4s0: interface state HT_SCAN->DISABLED
- wlp4s0: AP-DISABLED
- hostapd_interface_deinit_free(0xcd58a0)
- hostapd_interface_deinit_free: num_bss=1 conf->num_bss=1
- hostapd_interface_deinit(0xcd58a0)
- wlp4s0: interface state DISABLED->DISABLED
- hostapd_bss_deinit: deinit bss wlp4s0
- wlp4s0: Deauthenticate all stations
- nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0
- offchanok=0 wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
- nl80211: send_mlme -> send_frame
- nl80211: send_frame - Use bss->freq=0
- nl80211: send_frame -> send_frame_cmd
- nl80211: Frame command failed: ret=-22 (Invalid argument) (freq=0 wait=0)
- wlp4s0: AP-DISABLED
- hostapd_cleanup(hapd=0xcd7b90 (wlp4s0))
- hostapd_free_hapd_data: Interface wlp4s0 wasn't started
- hostapd_interface_deinit_free: driver=0x49d0c0 drv_priv=0xcd89e0 -> hapd_deinit
- nl80211: deinit ifname=wlp4s0 disabled_11b_rates=0
- nl80211: Remove monitor interface: refcount=0
- nl80211: Remove beacon (ifindex=4)
- netlink: Operstate: ifindex=4 linkmode=0 (kernel-control), operstate=6
- (IF_OPER_UP)
- nl80211: Set mode ifindex 4 iftype 2 (STATION)
- nl80211: Teardown AP(wlp4s0) - device_ap_sme=0 use_monitor=0
- nl80211: Unsubscribe mgmt frames handle 0x888888888845eae9 (AP teardown)
- hostapd_interface_free(0xcd58a0)
- hostapd_interface_free: free hapd 0xcd7b90
- hostapd_cleanup_iface(0xcd58a0)
- hostapd_cleanup_iface_partial(0xcd58a0)
- hostapd_cleanup_iface: free iface=0xcd58a0
- ```
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement