Linux_OCF_02-6_RM680-RM680-OEM1.bin

$ sudo ./Linux_OCF_02-6_RM680-RM680-OEM1.bin

IMPORTANT: READ THIS CAREFULLY AS BY DOWNLOADING, INSTALLING AND/OR USING
THE NOKIA N950 ONECLICKFLASHER­IMAGE YOU ACKNOWLEDGE AND AGREE TO THE
FOLLOWING TERMS AND CONDITIONS:

1) The NOKIA N950 ONECLICKFLASHER­IMAGE comprises of
   a) some software copyrighted by Nokia Corporation or third
      parties in binary form (collectively Licensed Software) and/or
   b) Open Source Software.

2) Licensed Software is distributed to you only in binary form. You
   a) are authorized to use the Licensed Software only in or in
      connection with the Nokia N950-products; and
   b) may not use, modify, adapt, translate, copy and/or distribute
      Licensed Software, except as expressly permitted herein.

3) The NOKIA N950 ONECLICKFLASHER­IMAGE is provided to you AS IS
   and Nokia, its affiliates and/or its licensors do not make any
   representations or warranties, express or implied (including, without
   any limitation, the warranties of  merchantability or fitness for
   a particular purpose, or that it will not infringe any third party
   patents, copyrights, trademarks or other rights).
   You agree that any downloading, installation and/or use by you of
   the NOKIA N950 ONECLICKFLASHER­IMAGE happens and is solely at your
   own risk and that Nokia assumes no liability whatsoever for any
   damages that you may incur or suffer in connection with the
   NOKIA N950 ONECLICKFLASHER­IMAGE and/or the installation or use
   thereof.

4) The Open Source Software is licensed and distributed under the
   applicable open source/free software licenses and/or other licenses,
   permissions, notices or disclaimers containing obligation or
   permission to provide the source code of such software. The relevant
   source code of the Open Source Software is made available to you
   per the product loan agreement you have concluded with us for the
   Nokia 950.

Press Y if your accept terms, any other to decline
y
This is OneClickFlasher for release 02-6
 - it will erase previous EMMC from the device
 - install the RM680 OEM image
 - install the EMMC RM680 content

Extracting the archive from OneClickFlasher ...
Extracting started at 14:10:32
Extracting finished at 14:10:32

Running Installer

Please make sure your device is properly powered OFF prior to
connecting the USB cable.
You can power your device off by holding down the power button
for 8+ seconds.
Flashing your device will erase all data and reset the device
back to factory state.
Please make sure you have backups of your data before proceeding
with flashing.
Depending on amount of data to be securely erased, the erasing may
take as long as 30 minutes until the flashing starts.

Please, be patient.

Check first that device is powered OFF and then connect USB cable.

First erasing eMMC
Then flashing image and eMMC
Flashing started at 14:10:33

flasher 3.12.1 (Oct  5 2011) Harmattan
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

USB device found at bus 002, device address 087.
Device identifier: 5A5541303331303634 (SN: ZUA031064)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.6.3
Found product RM-680 rev. 1124
Server implements softupd protocol version 1.8

Battery level 30 %, continuing.
Erasing, this may take a while.
Erase done.
Image SW version DFL61_HARMATTAN_3.2012.02-6_PR_RM680
Image moslo not present
Image tar skipped
Image config skipped

Battery level 37 %, continuing.

    image        [state    progress         transfer     flash speed]
---------------------------------------------------------------------
[x] cert-sw      [finished   100 %       1 /       1 kB      NA     ]
[x] cmt-2nd      [finished   100 %      95 /      95 kB      NA     ]
[x] cmt-algo     [finished   100 %     789 /     789 kB      NA     ]
[x] cmt-mcusw    [finished   100 %    6008 /    6008 kB    3256 kB/s]
[x] xloader      [finished   100 %      23 /      23 kB      NA     ]
[x] secondary    [finished   100 %      90 /      90 kB      NA     ]
[x] kernel       [finished   100 %    2714 /    2714 kB    1863 kB/s]
[x] rootfs       [finished   100 %  758715 /  758715 kB    9234 kB/s]
[x] mmc          [finished   100 %  172719 /  172719 kB   16670 kB/s]
Updating SW release
Success

Flashing finished at 14:28:04

Press Enter to exit
Unplug the USB cable from the device to boot new flashed image ...