Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 2011.09-rc1 (Oct 08 2014 - 10:38:33) Allwinner Technology
- [ 0.701]version: 2.1.0
- normal mode
- [ 0.710]pmbus: normal or secure os
- ready
- [ 0.715]PMU: AXP809
- [ 0.717]PMU: AXP809 found
- [ 0.720]PMU: AXP806
- [ 0.722]PMU: AXP806 found
- [ 0.725]a7 boot
- bat_vol=96, ratio=100
- try to set dcdc3 to 900 mV
- [ 0.732]PMU: dcdc3 900
- [ 0.734]PMU: pll1 1008 Mhz
- set power on vol to default
- dcdc1_vol = 3000, onoff=1
- dcdc2_vol = 900, onoff=0
- dcdc3_vol = 900, onoff=1
- dcdc4_vol = 900, onoff=1
- dcdc5_vol = 1500, onoff=1
- dc5ldo_vol = 900, onoff=1
- dldo2_vol = 3000, onoff=1
- eldo3_vol = 1800, onoff=1
- aldo1_vol = 3000, onoff=1
- aldo3_vol = 3000, onoff=1
- gpio1_vol = 2500, onoff=0
- find power_sply to end
- slave power
- dcdca_vol = 900, onoff=1
- dcdcb_vol = 0, onoff=0
- dcdcc_vol = 0, onoff=0
- dcdcd_vol = 900, onoff=1
- dcdce_vol = 2100, onoff=1
- aldo1_vol = 3000, onoff=1
- bldo1_vol = 1800, onoff=1
- bldo2_vol = 1800, onoff=1
- cldo1_vol = 3000, onoff=0
- find slave power sply to end
- supply=gpio1
- axp=axp809, supply=gpio1, vol=2500
- reg addr=0x6000b00, value=0x6, pmu_vol=2500
- supply=aldo2
- axp=axp809, supply=aldo2, vol=1800
- reg addr=0x6000b04, value=0x0, pmu_vol=1800
- supply=dcdc1
- axp=axp809, supply=dcdc1, vol=3000
- reg addr=0x6000b08, value=0xa, pmu_vol=3000
- supply=bldo1
- axp=axp806, supply=bldo1, vol=1800
- reg addr=0x6000b0c, value=0x0, pmu_vol=1800
- supply=eldo2
- axp=axp809, supply=eldo2, vol=1800
- reg addr=0x6000b10, value=0x0, pmu_vol=1800
- supply=dcdc1
- axp=axp809, supply=dcdc1, vol=3000
- reg addr=0x6000b14, value=0xa, pmu_vol=3000
- supply=gpio0
- axp=axp809, supply=gpio0, vol=3000
- reg addr=0x6000b18, value=0xa, pmu_vol=3000
- supply=dcdc1
- axp=axp809, supply=dcdc1, vol=3000
- reg addr=0x6000b1c, value=0xa, pmu_vol=3000
- supply=dldo2
- axp=axp809, supply=dldo2, vol=3000
- reg addr=0x8002f00, value=0xa, pmu_vol=3000
- supply=eldo3
- axp=axp809, supply=eldo3, vol=3000
- reg addr=0x8002f04, value=0xa, pmu_vol=3000
- config gpio bias voltage finish
- vbus exist
- no battery, limit to dc
- fel key old mode
- run key detect
- no key found
- no key input
- dram_para_set start
- dram_para_set end
- [ 1.478]DRAM: 2 GiB
- relocation Offset is: 75aee000
- gic: normal or no secure os mode
- deu_mode1 not exist.
- get clock handle by id 36 fail!
- get clock handle by id 36 fail!
- lcd0.lcd_pwm_freq is ZERO
- lcd1.lcd_pwm_freq is ZERO
- lcd 2 is not register
- screen 0 do not support HDMI TYPE!
- screen 2 do not support HDMI TYPE!
- smcl's set manager is NULL
- smbl's set manager is NULL
- screen_id 0 do not support HDMI TYPE!
- get hdmi0 failed!
- [ 1.786]boot_disp.output_disp=1
- [ 1.790]boot_disp.output_type=3
- [ 1.793]boot_disp.output_mode=4
- [ 1.796]boot_disp.auto_hpd=1
- hdmi open
- Hdmi_open
- Hdmi_hal_video_enable_sync
- workmode = 0
- MMC: 0
- [ 1.911][mmc]: mmc driver ver 2014-9-1 10:54:35
- [ 1.916][mmc]: get sdc_f_max fail,use default sdc_f_max 48000000
- [ 1.922][mmc]: get sdc_ex_dly_used fail,use default dly
- [ 1.928][mmc]: PC Bias: 0x06000b08 0x0000000a
- [ 1.932][mmc]: SUNXI SD/MMC: 0
- [ 1.945][mmc]: ************Try SD card 0************
- [ 1.980][mmc]: MID 000002 PSN 23dd1648
- [ 1.983][mmc]: PNM SA16G -- 0x53-41-31-36-47-00
- [ 1.988][mmc]: PRV 1.2
- [ 1.990][mmc]: MDT m-6 y-2014
- [ 1.994][mmc]: ---------------mmc->clock 48000000-----------
- [ 1.999][mmc]: ---------------mmc->bus_width 4--------------
- [ 2.005][mmc]: SD/MMC Card: 4bit, capacity: 14992MB
- [ 2.010][mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB
- [ 2.015][mmc]: ************SD/MMC 0 init OK!!!************
- [ 2.022]sunxi flash init ok
- fail to find part named env
- Using default environment
- In: serial
- Out: serial
- Err: serial
- --------fastboot partitions--------
- mbr not exist
- base bootcmd=run setargs_cubie boot_normal
- bootcmd set setargs_mmc
- key 0
- cant find rcvy value
- cant find fstbt value
- no misc partition is found
- misc_message->command = 0
- to be run cmd=run setargs_cubie boot_normal
- WORK_MODE_BOOT
- board_status_probe
- sunxi_bmp_logo_display
- sunxi flash error: cant get part 0 offset
- ** Can't read from device 0 **
- ** Unable to use sunxi_flash 0:1 for fatload **
- sunxi bmp info error : unable to open logo file bootlogo.bmp
- [ 2.080]Hit any key to stop autoboot: 0
- [ 5.732][mmc]: blkcnt should not be 0
- ## Booting kernel from Legacy Image at 20007800 ...
- Image Name:
- Image Type: ARM Linux Multi-File Image (uncompressed)
- Data Size: 8962291 Bytes = 8.5 MiB
- Load Address: 20008000
- Entry Point: 20008000
- Contents:
- Image 0: 4005648 Bytes = 3.8 MiB
- Image 1: 4956631 Bytes = 4.7 MiB
- Verifying Checksum ... OK
- ## Loading init Ramdisk from multi component Legacy Image at 20007800 ...
- Loading Multi-File Image ... OK
- OK
- WARNING: legacy format multi component image overwritten
- [ 5.890][mmc]: MMC Device 2 not found
- [ 5.894][mmc]: mmc not find,so not exit
- [ 5.898]
- Starting kernel ...
- Booting Linux on physical CPU 0x0
- Initializing cgroup subsys cpuset
- Initializing cgroup subsys cpu
- Initializing cgroup subsys cpuacct
- Linux version 4.2.0-rc4 (root@cubieez) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP Thu Aug 6 14:26:06 CEST 2015
- CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=30c5387d
- CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- Machine model: Cubietech Cubieboard4
- Forcing write-allocate cache policy for SMP
- Memory policy: Data cache writealloc
- On node 0 totalpages: 524288
- free_area_init_node: node 0, pgdat c07bd340, node_mem_map ee5f9000
- Normal zone: 1710 pages used for memmap
- Normal zone: 0 pages reserved
- Normal zone: 194560 pages, LIFO batch:31
- HighMem zone: 329728 pages, LIFO batch:31
- PERCPU: Embedded 9 pages/cpu @ee59a000 s13440 r0 d23424 u36864
- pcpu-alloc: s13440 r0 d23424 u36864 alloc=9*4096
- pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522578
- Kernel command line: console=tty1 console=ttyS0,115200 root=/dev/mmcblk0p2 loglevel=8
- PID hash table entries: 4096 (order: 2, 16384 bytes)
- Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
- Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
- Memory: 2069300K/2097152K available (5746K kernel code, 292K rwdata, 1592K rodata, 268K init, 281K bss, 27852K reserved, 0K cma-reserved, 1318912K highmem)
- Virtual kernel memory layout:
- vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
- vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
- lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
- pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- .text : 0xc0008000 - 0xc0732e98 (7340 kB)
- .init : 0xc0733000 - 0xc0776000 ( 268 kB)
- .data : 0xc0776000 - 0xc07bf1a0 ( 293 kB)
- .bss : 0xc07c2000 - 0xc0808400 ( 281 kB)
- SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
- Hierarchical RCU implementation.
- Additional per-CPU info printed with stalls.
- Build-time adjustment of leaf fanout to 32.
- NR_IRQS:16 nr_irqs:16 16
- GIC physical location is 0x1c41000
- Architected cp15 timer(s) running at 24.00MHz (phys).
- clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
- sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
- Switching to timer-based delay loop, resolution 41ns
- clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
- Console: colour dummy device 80x30
- console [tty1] enabled
- Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=120000)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
- Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
- Initializing cgroup subsys blkio
- Initializing cgroup subsys memory
- Initializing cgroup subsys devices
- CPU: Testing write buffer coherency: ok
- /cpus/cpu@0 missing clock-frequency property
- /cpus/cpu@1 missing clock-frequency property
- /cpus/cpu@2 missing clock-frequency property
- /cpus/cpu@3 missing clock-frequency property
- /cpus/cpu@100 missing clock-frequency property
- /cpus/cpu@101 missing clock-frequency property
- /cpus/cpu@102 missing clock-frequency property
- /cpus/cpu@103 missing clock-frequency property
- CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
- Setting up static identity map for 0x200082c0 - 0x20008318
- Brought up 1 CPUs
- SMP: Total of 1 processors activated (48.00 BogoMIPS).
- CPU: All CPU(s) started in SVC mode.
- devtmpfs: initialized
- VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
- clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns
- xor: measuring software checksum speed
- arm4regs : 1332.000 MB/sec
- 8regs : 860.000 MB/sec
- 32regs : 836.000 MB/sec
- neon : 1245.600 MB/sec
- xor: using function: arm4regs (1332.000 MB/sec)
- pinctrl core: initialized pinctrl subsystem
- NET: Registered protocol family 16
- DMA: preallocated 256 KiB pool for atomic coherent allocations
- No ATAGs?
- raid6: int32x1 gen() 148 MB/s
- raid6: int32x1 xor() 116 MB/s
- raid6: int32x2 gen() 191 MB/s
- raid6: int32x2 xor() 121 MB/s
- raid6: int32x4 gen() 187 MB/s
- raid6: int32x4 xor() 127 MB/s
- raid6: int32x8 gen() 184 MB/s
- raid6: int32x8 xor() 118 MB/s
- raid6: neonx1 gen() 482 MB/s
- raid6: neonx2 gen() 651 MB/s
- raid6: neonx4 gen() 789 MB/s
- raid6: neonx8 gen() 675 MB/s
- raid6: using algorithm neonx4 gen() 789 MB/s
- raid6: using intx1 recovery algorithm
- vgaarb: loaded
- SCSI subsystem initialized
- libata version 3.00 loaded.
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- pps_core: LinuxPPS API ver. 1 registered
- pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- PTP clock support registered
- Advanced Linux Sound Architecture Driver Initialized.
- clocksource: Switched to clocksource arch_sys_counter
- NET: Registered protocol family 2
- TCP established hash table entries: 8192 (order: 3, 32768 bytes)
- TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
- TCP: Hash tables configured (established 8192 bind 8192)
- UDP hash table entries: 512 (order: 2, 16384 bytes)
- UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
- NET: Registered protocol family 1
- PCI: CLS 0 bytes, default 64
- kvm [1]: HYP mode not available
- futex hash table entries: 2048 (order: 5, 131072 bytes)
- squashfs: version 4.0 (2009/01/31) Phillip Lougher
- bounce: pool size: 64 pages
- Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
- io scheduler noop registered
- io scheduler deadline registered
- io scheduler cfq registered (default)
- sun9i-a80-pinctrl 6000800.pinctrl: initialized sunXi PIO driver
- Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
- console [ttyS0] disabled
- 7000000.serial: ttyS0 at MMIO 0x7000000 (irq = 35, base_baud = 1500000) is a U6_16550A
- console [ttyS0] enabled
- loop: module loaded
- null: module loaded
- tun: Universal TUN/TAP device driver, 1.6
- tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
- e1000: Copyright (c) 1999-2006 Intel Corporation.
- usbcore: registered new interface driver asix
- usbcore: registered new interface driver ax88179_178a
- usbcore: registered new interface driver cdc_ether
- ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- ohci-pci: OHCI PCI platform driver
- ohci-platform: OHCI generic platform driver
- mousedev: PS/2 mouse device common for all mice
- i2c /dev entries driver
- sunxi-wdt 6000ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
- sunxi-wdt 8001000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
- softdog: Software Watchdog Timer: 0.08 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)
- sunxi-mmc 1c0f000.mmc: No vqmmc regulator found
- sunxi-mmc 1c0f000.mmc: Could not get ahb clock
- sunxi-mmc 1c11000.mmc: No vqmmc regulator found
- sunxi-mmc 1c11000.mmc: Could not get ahb clock
- usbcore: registered new interface driver usbhid
- usbhid: USB HID core driver
- gre: GRE over IPv4 demultiplexor driver
- ip_gre: GRE over IPv4 tunneling driver
- NET: Registered protocol family 10
- sit: IPv6 over IPv4 tunneling driver
- bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- 8021q: 802.1Q VLAN Support v1.8
- Registering SWP/SWPB emulation handler
- Btrfs loaded
- sunxi-mmc 1c0f000.mmc: No vqmmc regulator found
- sunxi-mmc 1c0f000.mmc: Got CD GPIO
- sunxi-mmc 1c0f000.mmc: base:0xf00a0000 irq:21
- sunxi-mmc 1c11000.mmc: No vqmmc regulator found
- sunxi-mmc 1c11000.mmc: base:0xf00a4000 irq:22
- hctosys: unable to open rtc device (rtc0)
- vcc5v0: disabling
- vcc3v3: disabling
- ALSA device list:
- No soundcards found.
- VFS: Cannot open root device "mmcblk0p2" or unknown-block(0,0): error -6
- Please append a correct "root=" boot option; here are the available partitions:
- Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
- CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.2.0-rc4 #2
- Hardware name: Allwinner sun9i Family
- [<c002838c>] (unwind_backtrace) from [<c0024718>] (show_stack+0x10/0x14)
- [<c0024718>] (show_stack) from [<c0573554>] (dump_stack+0x88/0x98)
- [<c0573554>] (dump_stack) from [<c05713f0>] (panic+0x9c/0x21c)
- [<c05713f0>] (panic) from [<c0734428>] (mount_block_root+0x230/0x2c4)
- [<c0734428>] (mount_block_root) from [<c0734684>] (prepare_namespace+0x14c/0x194)
- [<c0734684>] (prepare_namespace) from [<c07340dc>] (kernel_init_freeable+0x26c/0x27c)
- [<c07340dc>] (kernel_init_freeable) from [<c057051c>] (kernel_init+0x8/0xe8)
- [<c057051c>] (kernel_init) from [<c00218e8>] (ret_from_fork+0x14/0x2c)
- ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement