API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Oct 7th, 2012
77
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 13.11 KB | None | 0 0
raw download clone embed print report diff
  1. =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2012.10.07 22:35:24 =~=~=~=~=~=~=~=~=~=~=~=
  2. Oct 2 201217:06:24
  3. FRAC 0x92925552
  4. memory type is DDR2
  5. Wait for ddr ready 1power 0x00820616
  6. Frac 0x92925552
  7. start change cpu freq
  8. hbus 0x00000003
  9. cpu 0x00010001
  10. start test memory accress
  11. ddr2 0x40000000
  12. finish simple test
  13.  
  14.  
  15. U-Boot 2011.09 (Oct 02 2012 - 21:33:21)
  16.  
  17. Freescale i.MX28 family
  18. I2C: ready
  19. DRAM: 128 MiB
  20. WARNING: Caches not enabled
  21. MX28 I2C pads init
  22. heg_pca955x_init
  23. MXS I2C: No slave ACK
  24. MXS I2C read: Failed writing address 27 6
  25. MXS I2C: No slave ACK
  26. MXS I2C read: Failed writing address 26 6
  27. HEG PCA955x v3 detected, PCA953X @ 25
  28. HEG PCA955x initialized
  29. MX28 GMPI Init
  30. MX28 FEC pins init
  31. NAND: 512 MiB
  32. MMC: MXS MMC: 0
  33. In: serial
  34. Out: serial
  35. Err: serial
  36. Net: FEC0
  37. Hit any key to stop autoboot: 3  2  1  0
  38.  
  39. NAND read: device 0 offset 0xa00000, size 0x400000
  40. 4194304 bytes read: OK
  41. ## Booting kernel from Legacy Image at 42000000 ...
  42. Image Name: Linux-2.6.35.3-571-gcca29a0
  43. Created: 2012-10-07 15:42:52 UTC
  44. Image Type: ARM Linux Kernel Image (uncompressed)
  45. Data Size: 2343468 Bytes = 2.2 MiB
  46. Load Address: 40008000
  47. Entry Point: 40008000
  48. Verifying Checksum ... OK
  49. Loading Kernel Image ... OK
  50. OK
  51.  
  52. Starting kernel ...
  53.  
  54. Uncompressing Linux... done, booting the kernel.
  55. Linux version 2.6.35.3-571-gcca29a0 (lars@lars-UX32VD) (gcc version 4.4.4 (4.4.4_09.06.2010) ) #216 PREEMPT Sun Oct 7 17:42:47 CEST 2012
  56.  
  57. CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
  58.  
  59. CPU: VIVT data cache, VIVT instruction cache
  60.  
  61. Machine: Freescale MX28HEG v3 board
  62.  
  63. Memory policy: ECC disabled, Data cache writeback
  64.  
  65. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
  66.  
  67. Kernel command line: noinitrd console=ttyAM0,115200 fec_mac=00:04:9F:01:03:ff ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs gpmi
  68.  
  69. PID hash table entries: 512 (order: -1, 2048 bytes)
  70.  
  71. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  72.  
  73. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  74.  
  75. Memory: 128MB = 128MB total
  76.  
  77. Memory: 124800k/124800k available, 6272k reserved, 0K highmem
  78.  
  79. Virtual kernel memory layout:
  80.  
  81. vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  82.  
  83. fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  84.  
  85. DMA : 0xfde00000 - 0xffe00000 ( 32 MB)
  86.  
  87. vmalloc : 0xc8800000 - 0xf0000000 ( 632 MB)
  88.  
  89. lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
  90.  
  91. modules : 0xbf000000 - 0xc0000000 ( 16 MB)
  92.  
  93. .init : 0xc0008000 - 0xc002c000 ( 144 kB)
  94.  
  95. .text : 0xc002c000 - 0xc048d000 (4484 kB)
  96.  
  97. .data : 0xc048e000 - 0xc04c1120 ( 205 kB)
  98.  
  99. SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  100.  
  101. Hierarchical RCU implementation.
  102.  
  103. RCU-based detection of stalled CPUs is disabled.
  104.  
  105. Verbose stalled-CPUs detection is disabled.
  106.  
  107. NR_IRQS:352
  108.  
  109. Console: colour dummy device 80x30
  110.  
  111. console [ttyAM0] enabled
  112.  
  113. Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
  114.  
  115. pid_max: default: 32768 minimum: 301
  116.  
  117. Security Framework initialized
  118.  
  119. Mount-cache hash table entries: 512
  120.  
  121. CPU: Testing write buffer coherency: ok
  122.  
  123. regulator: core version 0.5
  124.  
  125. NET: Registered protocol family 16
  126.  
  127. regulator: vddd: 800 <--> 1575 mV at 1500 mV fast normal
  128.  
  129. HEG: Enabling 1.2V Reg
  130.  
  131. regulator: vdddbo: 800 <--> 1575 mV fast normal
  132.  
  133. regulator: vdda: 1500 <--> 2275 mV at 1800 mV fast normal
  134.  
  135. vddio = 3380000, val=10
  136.  
  137. regulator: vddio: 2880 <--> 3680 mV at 3380 mV fast normal
  138.  
  139. regulator: overall_current: fast normal
  140.  
  141. regulator: vbus5v:
  142.  
  143. regulator: mxs-duart-1: fast normal
  144.  
  145. regulator: mxs-bl-1: fast normal
  146.  
  147. regulator: mxs-i2c-1: fast normal
  148.  
  149. regulator: mmc_ssp-1: fast normal
  150.  
  151. regulator: mmc_ssp-2: fast normal
  152.  
  153. regulator: charger-1: fast normal
  154.  
  155. regulator: power-test-1: fast normal
  156.  
  157. regulator: cpufreq-1: fast normal
  158.  
  159. HEG: Version is 3
  160.  
  161. i.MX IRAM pool: 124 KB@0xc8820000
  162.  
  163. Initializing GPIO...
  164.  
  165. Initializing HEG PINS...
  166.  
  167. Pin'AUART0.RX' 0'AUART0.TX' 1'AUART1.RX' 2'AUART1.TX' 3'usb0' 4'usb1' 5'usb0_id' 6'I2C0_SCL' 7'I2C0_SDA' 8'SAIF0_MCLK' 9'SAIF0_LRCLK' 10'SAIF0_BITCLK' 11'SAIF0_SDATA0' 12'SAIF1_SDATA0' 13'SPDIF' 14
  168.  
  169. Initializing GPMI pins
  170.  
  171. Pin'GPMI D0' 0'GPMI D1' 1'GPMI D2' 2'GPMI D3' 3'GPMI D4' 4'GPMI D5' 5'GPMI D6' 6'GPMI D7' 7'GPMI CE0-' 8'GPMI RDY0' 9'GPMI RDY1' 10'GPMI RD-' 11'GPMI WR-' 12'GPMI ALE' 13'GPMI CLE' 14'GPMI RST-' 15
  172.  
  173. Pin'ENET0_MDC' 0'ENET0_MDIO' 1'ENET0_RX_EN' 2'ENET0_RXD0' 3'ENET0_RXD1' 4'ENET0_TX_EN' 5'ENET0_TXD0' 6'ENET0_TXD1' 7'ENET1_RX_EN' 8'ENET1_RXD0' 9'ENET1_RXD1' 10'ENET1_TX_EN' 11'ENET1_TXD0' 12'ENET1_TXD1' 13'ENET_CLK' 14
  174.  
  175. Initializing device...
  176.  
  177. XXXlpj mx28_init_i2c done
  178.  
  179. Initializing HEG device...
  180.  
  181. usb DR wakeup device is registered
  182.  
  183. IMX usb wakeup probe
  184.  
  185. audit: cannot initialize inotify handle
  186.  
  187. bio: create slab <bio-0> at 0
  188.  
  189. SCSI subsystem initialized
  190.  
  191. Freescale USB OTG Driver loaded, $Revision: 1.55 $
  192.  
  193. usbcore: registered new interface driver usbfs
  194.  
  195. usbcore: registered new interface driver hub
  196.  
  197. usbcore: registered new device driver usb
  198.  
  199. Advanced Linux Sound Architecture Driver Version 1.0.23.
  200.  
  201. Switching to clocksource mxs clock source
  202.  
  203. NET: Registered protocol family 2
  204.  
  205. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  206.  
  207. TCP established hash table entries: 4096 (order: 3, 32768 bytes)
  208.  
  209. TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
  210.  
  211. TCP: Hash tables configured (established 4096 bind 4096)
  212.  
  213. TCP reno registered
  214.  
  215. UDP hash table entries: 256 (order: 0, 4096 bytes)
  216.  
  217. UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  218.  
  219. NET: Registered protocol family 1
  220.  
  221. RPC: Registered udp transport module.
  222.  
  223. RPC: Registered tcp transport module.
  224.  
  225. RPC: Registered tcp NFSv4.1 backchannel transport module.
  226.  
  227. Bus freq driver module loaded
  228.  
  229. IMX usb wakeup probe
  230.  
  231. usb h1 wakeup device is registered
  232.  
  233. pca953x 0-0027: failed reading register
  234.  
  235. HEG: PCA955x at 27 missing
  236.  
  237. pca953x: probe of 0-0027 failed with error -110
  238.  
  239. pca953x 0-0026: failed reading register
  240.  
  241. HEG: PCA955x at 26 missing
  242.  
  243. pca953x: probe of 0-0026 failed with error -110
  244.  
  245. pca953x 0-0025: failed reading register
  246.  
  247. HEG: PCA955x at 25 missing
  248.  
  249. pca953x: probe of 0-0025 failed with error -110
  250.  
  251. mxs_cpu_init: cpufreq init finished
  252.  
  253. audit: initializing netlink socket (disabled)
  254.  
  255. type=2000 audit(3.650:1): initialized
  256.  
  257. VFS: Disk quotas dquot_6.5.2
  258.  
  259. Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  260.  
  261. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
  262.  
  263. msgmni has been set to 243
  264.  
  265. alg: No test for stdrng (krng)
  266.  
  267. cryptodev: driver loaded.
  268.  
  269. Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
  270.  
  271. io scheduler noop registered
  272.  
  273. io scheduler deadline registered
  274.  
  275. io scheduler cfq registered (default)
  276.  
  277. mxs-duart.0: ttyAM0 at MMIO 0x80074000 (irq = 47) is a DebugUART
  278.  
  279. mxs-auart.0: ttySP0 at MMIO 0x8006a000 (irq = 112) is a mxs-auart.0
  280.  
  281. Found APPUART 3.1.0
  282.  
  283. mxs-auart.1: ttySP1 at MMIO 0x8006c000 (irq = 113) is a mxs-auart.1
  284.  
  285. Found APPUART 3.1.0
  286.  
  287. brd: module loaded
  288.  
  289. loop: module loaded
  290.  
  291. i.MX GPMI NFC
  292.  
  293. NFC: Version 1, 8-chip GPMI and BCH
  294.  
  295. Boot ROM: Version 1, Single-chip boot area, block mark swapping supported
  296.  
  297. Scanning for NAND Flash chips...
  298.  
  299. NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron NAND 512MiB 3,3V 8-bit)
  300.  
  301. -----------------------------
  302.  
  303. NAND Flash Device Information
  304.  
  305. -----------------------------
  306.  
  307. Manufacturer : Micron (0x2c)
  308.  
  309. Device Code : 0xdc
  310.  
  311. Cell Technology : SLC
  312.  
  313. Chip Size : 512 MiB
  314.  
  315. Pages per Block : 64
  316.  
  317. Page Geometry : 2048+64
  318.  
  319. ECC Strength : 4 bits
  320.  
  321. ECC Size : 512 B
  322.  
  323. Data Setup Time : 20 ns
  324.  
  325. Data Hold Time : 10 ns
  326.  
  327. Address Setup Time: 10 ns
  328.  
  329. GPMI Sample Delay : 6 ns
  330.  
  331. tREA : Unknown
  332.  
  333. tRLOH : Unknown
  334.  
  335. tRHOH : Unknown
  336.  
  337. Description : MT29F4G08AAA
  338.  
  339. -----------------
  340.  
  341. Physical Geometry
  342.  
  343. -----------------
  344.  
  345. Chip Count : 1
  346.  
  347. Page Data Size in Bytes: 2048 (0x800)
  348.  
  349. Page OOB Size in Bytes : 64
  350.  
  351. Block Size in Bytes : 131072 (0x20000)
  352.  
  353. Block Size in Pages : 64 (0x40)
  354.  
  355. Chip Size in Bytes : 536870912 (0x20000000)
  356.  
  357. Chip Size in Pages : 262144 (0x40000)
  358.  
  359. Chip Size in Blocks : 4096 (0x1000)
  360.  
  361. Medium Size in Bytes : 536870912 (0x20000000)
  362.  
  363. ------------
  364.  
  365. NFC Geometry
  366.  
  367. ------------
  368.  
  369. ECC Algorithm : BCH
  370.  
  371. ECC Strength : 8
  372.  
  373. Page Size in Bytes : 2112
  374.  
  375. Metadata Size in Bytes : 10
  376.  
  377. ECC Chunk Size in Bytes: 512
  378.  
  379. ECC Chunk Count : 4
  380.  
  381. Payload Size in Bytes : 2048
  382.  
  383. Auxiliary Size in Bytes: 16
  384.  
  385. Auxiliary Status Offset: 12
  386.  
  387. Block Mark Byte Offset : 1999
  388.  
  389. Block Mark Bit Offset : 0
  390.  
  391. -----------------
  392.  
  393. Boot ROM Geometry
  394.  
  395. -----------------
  396.  
  397. Boot Area Count : 1
  398.  
  399. Boot Area Size in Bytes : 9437184 (0x900000)
  400.  
  401. Stride Size in Pages : 64
  402.  
  403. Search Area Stride Exponent: 2
  404.  
  405. Scanning device for bad blocks
  406.  
  407. Boot area protection is enabled.
  408.  
  409. Creating 2 MTD partitions on "gpmi-nfc-main":
  410.  
  411. 0x000000000000-0x000000900000 : "gpmi-nfc-0-boot"
  412.  
  413. 0x000001400000-0x000020000000 : "gpmi-nfc-general-use"
  414.  
  415. UBI: attaching mtd1 to ubi0
  416.  
  417. UBI: physical eraseblock size: 131072 bytes (128 KiB)
  418.  
  419. UBI: logical eraseblock size: 126976 bytes
  420.  
  421. UBI: smallest flash I/O unit: 2048
  422.  
  423. UBI: VID header offset: 2048 (aligned 2048)
  424.  
  425. UBI: data offset: 4096
  426.  
  427. UBI: attached mtd1 to ubi0
  428.  
  429. UBI: MTD device name: "gpmi-nfc-general-use"
  430.  
  431. UBI: MTD device size: 492 MiB
  432.  
  433. UBI: number of good PEBs: 3936
  434.  
  435. UBI: number of bad PEBs: 0
  436.  
  437. UBI: max. allowed volumes: 128
  438.  
  439. UBI: wear-leveling threshold: 4096
  440.  
  441. UBI: number of internal volumes: 1
  442.  
  443. UBI: number of user volumes: 1
  444.  
  445. UBI: available PEBs: 0
  446.  
  447. UBI: total number of reserved PEBs: 3936
  448.  
  449. UBI: number of PEBs reserved for bad PEB handling: 39
  450.  
  451. UBI: max/mean erase counter: 4/1
  452.  
  453. UBI: image sequence number: 0
  454.  
  455. UBI: background thread "ubi_bgt0d" started, PID 947
  456.  
  457. ubiblka:
  458.  
  459. unknown partition table
  460.  
  461. FEC Ethernet Driver
  462.  
  463. mx28heg_enet_gpio_init
  464.  
  465. fec_enet_mii_bus: probed
  466.  
  467. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  468.  
  469. fsl-ehci fsl-ehci: Freescale On-Chip EHCI Host Controller
  470.  
  471. fsl-ehci fsl-ehci: new USB bus registered, assigned bus number 1
  472.  
  473. fsl-ehci fsl-ehci: irq 93, io base 0x80080000
  474.  
  475. fsl-ehci fsl-ehci: USB 2.0 started, EHCI 1.00
  476.  
  477. hub 1-0:1.0: USB hub found
  478.  
  479. hub 1-0:1.0: 1 port detected
  480.  
  481. fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
  482.  
  483. fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 2
  484.  
  485. fsl-ehci fsl-ehci.0: irq 92, io base 0x80090000
  486.  
  487. fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
  488.  
  489. hub 2-0:1.0: USB hub found
  490.  
  491. hub 2-0:1.0: 1 port detected
  492.  
  493. Initializing USB Mass Storage driver...
  494.  
  495. usbcore: registered new interface driver usb-storage
  496.  
  497. USB Mass Storage support registered.
  498.  
  499. ARC USBOTG Device Controller driver (1 August 2005)
  500.  
  501. mice: PS/2 mouse device common for all mice
  502.  
  503. MXS RTC driver v1.0 hardware v2.3.0
  504.  
  505. mxs-rtc mxs-rtc.0: rtc core: registered mxs-rtc as rtc0
  506.  
  507. mxs watchdog: initialized, heartbeat 19 sec
  508.  
  509. dcp dcp.0: DCP crypto enabled.!
  510.  
  511. usbcore: registered new interface driver hiddev
  512.  
  513. usbcore: registered new interface driver usbhid
  514.  
  515. usbhid: USB HID core driver
  516.  
  517. usb 2-1: new high speed USB device using fsl-ehci and address 2
  518.  
  519. hub 2-1:1.0: USB hub found
  520.  
  521. hub 2-1:1.0: 3 ports detected
  522.  
  523. sgtl5000_hw_read: read reg error : Reg 0x00
  524.  
  525. Device with ID register 0 is not a SGTL5000
  526.  
  527. mxs-spdif mxs-spdif.0: MXS SPDIF Audio Transmitter
  528.  
  529. No device for codec mxs spdif
  530.  
  531. No device for DAI mxs spdif
  532.  
  533. No device for DAI mxs-saif
  534.  
  535. No device for DAI mxs-spdif
  536.  
  537. asoc: mxs spdif <-> mxs-spdif mapping ok
  538.  
  539. ALSA device list:
  540.  
  541. #0: mxs-evk (mxs spdif)
  542.  
  543. TCP cubic registered
  544.  
  545. NET: Registered protocol family 17
  546.  
  547. can: controller area network core (rev 20090105 abi 8)
  548.  
  549. NET: Registered protocol family 29
  550.  
  551. can: raw protocol (rev 20090105)
  552.  
  553. mxs-rtc mxs-rtc.0: setting system clock to 1970-01-03 01:02:56 UTC (176576)
  554.  
  555. UBIFS error (pid 1): ubifs_read_node: bad node type (0 but expected 6)
  556.  
  557. UBIFS error (pid 1): ubifs_read_node: bad node at LEB 0:0
  558.  
  559. List of all partitions:
  560.  
  561. 1f00 9216 mtdblock0 (driver?)
  562.  
  563. 1f01 503808 mtdblock1 (driver?)
  564.  
  565. fe00 482732 ubiblka (driver?)
  566.  
  567. No filesystem could mount root, tried: ubifs
  568.  
  569. Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
  570.  
  571. Backtrace:
  572.  
  573. [<c00314a8>] (dump_backtrace+0x0/0x114) from [<c039e5dc>] (dump_stack+0x18/0x1c)
  574.  
  575. r7:c0028a24 r6:00008000 r5:c7c14006 r4:c050ded8
  576.  
  577. [<c039e5c4>] (dump_stack+0x0/0x1c) from [<c039e658>] (panic+0x78/0xf4)
  578.  
  579. [<c039e5e0>] (panic+0x0/0xf4) from [<c000902c>] (mount_block_root+0x1d8/0x218)
  580.  
  581. r3:00000000 r2:00000020 r1:c7c27f78 r0:c04595f5
  582.  
  583. [<c0008e54>] (mount_block_root+0x0/0x218) from [<c00091fc>] (prepare_namespace+0x94/0x1c4)
  584.  
  585. [<c0009168>] (prepare_namespace+0x0/0x1c4) from [<c00084f8>] (kernel_init+0x128/0x170)
  586.  
  587. r5:c0027bd4 r4:c050d020
  588.  
  589. [<c00083d0>] (kernel_init+0x0/0x170) from [<c004d600>] (do_exit+0x0/0x6dc)
  590.  
  591. r5:c00083d0 r4:00000000
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!