Texas Instruments X-Loader 1.4.4ss (Sep 22 2010 - 16:12:19)
Beagle Rev C4
Reading boot sector
Loading u-boot.bin from mmc


U-Boot 2010.03-dirty (Oct 18 2010 - 11:31:58)

OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max clock-720Mhz
OMAP3 Beagle board + LPDDR/NAND
I2C:   ready
DRAM:  256 MB
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial

Probing for expansion boards, if none are connected you'll see a harmless I2C error.

timed out in wait_for_pin: I2C_STAT=0
I2C read: I/O error
Unrecognized expansion board: 0
Beagle Rev C4
Die ID #39d2000400000000040365fa14015011
Hit any key to stop autoboot:  0
No MMC card found
Unknown command 'mmcinit' - try 'help'
Booting from nand ...

NAND read: device 0 offset 0x280000, size 0x400000
 4194304 bytes read: OK
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   Linux-2.6.32.9-gd75fac4-dirty
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2380788 Bytes =  2.3 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux..........................................................................................................
Linux version 2.6.32.9-gd75fac4-dirty (erin@midnight) (gcc version 4.4.0 (GCC) ) #18 Thu Jul 29 18:07:25 CST 2010
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: OMAP3 Beagle Board
Memory policy: ECC disabled, Data cache writeback
OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
Reserving 12582912 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: console=ttyS2,115200n8 vram=12M omapdss.def_disp=dvi omapfb.mode=dvi:1024x768MR-24@60 ubi.mtd=4 root=ubt
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 128MB = 256MB total
Memory: 242176KB available (4120K code, 788K data, 128K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:402
Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
Reprogramming SDRC clock to 332000000 Hz
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP GPIO hardware version 2.5
OMAP clockevent source: GPTIMER12 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 485.26 BogoMIPS (lpj=1896448)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
MUX: setup AF15_34XX_GPIO168 (0xfa0021be): 0x0118 -> 0x010c
I2C bus2 does not have external pull-up, drop i2c_bus2 registration
MUX: setup Y9_3430_USB1HS_PHY_STP (0xfa0025d8): 0x001b -> 0x0003
MUX: setup Y8_3430_USB1HS_PHY_CLK (0xfa0025da): 0x0013 -> 0x0003
MUX: setup AA14_3430_USB1HS_PHY_DIR (0xfa0025ec): 0x0113 -> 0x010b
MUX: setup AA11_3430_USB1HS_PHY_NXT (0xfa0025ee): 0x0113 -> 0x010b
MUX: setup W13_3430_USB1HS_PHY_D0 (0xfa0025dc): 0x0113 -> 0x010b
MUX: setup W12_3430_USB1HS_PHY_D1 (0xfa0025de): 0x0113 -> 0x010b
MUX: setup W11_3430_USB1HS_PHY_D2 (0xfa0025e0): 0x0113 -> 0x010b
MUX: setup Y11_3430_USB1HS_PHY_D3 (0xfa0025ea): 0x0113 -> 0x010b
MUX: setup W9_3430_USB1HS_PHY_D4 (0xfa0025e4): 0x0113 -> 0x010b
MUX: setup Y12_3430_USB1HS_PHY_D5 (0xfa0025e6): 0x0113 -> 0x010b
MUX: setup W8_3430_USB1HS_PHY_D6 (0xfa0025e8): 0x0113 -> 0x010b
MUX: setup Y13_3430_USB1HS_PHY_D7 (0xfa0025e2): 0x0113 -> 0x010b
MUX: setup AA10_3430_USB2HS_PHY_STP (0xfa0025f2): 0x0013 -> 0x0003
MUX: setup AA8_3430_USB2HS_PHY_CLK (0xfa0025f0): 0x0013 -> 0x0003
MUX: setup AA9_3430_USB2HS_PHY_DIR (0xfa0025f4): 0x0113 -> 0x010b
MUX: setup AB11_3430_USB2HS_PHY_NXT (0xfa0025f6): 0x0113 -> 0x010b
MUX: setup AB10_3430_USB2HS_PHY_D0 (0xfa0025f8): 0x0113 -> 0x010b
MUX: setup AB9_3430_USB2HS_PHY_D1 (0xfa0025fa): 0x0113 -> 0x010b
MUX: setup W3_3430_USB2HS_PHY_D2 (0xfa0021d4): 0x0113 -> 0x010b
MUX: setup T4_3430_USB2HS_PHY_D3 (0xfa0021de): 0x0113 -> 0x010b
MUX: setup T3_3430_USB2HS_PHY_D4 (0xfa0021d8): 0x0113 -> 0x010b
MUX: setup R3_3430_USB2HS_PHY_D5 (0xfa0021da): 0x0113 -> 0x010b
MUX: setup R4_3430_USB2HS_PHY_D6 (0xfa0021dc): 0x0113 -> 0x010b
MUX: setup T2_3430_USB2HS_PHY_D7 (0xfa0021d6): 0x0113 -> 0x010b
Found NAND on CS0
Registering NAND on CS0
MUX: setup N28_34XX_MMC1_CLK (0xfa002144): 0x0018 -> 0x0118
Unable to get DVI reset GPIO
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
MUX: setup AG9_34XX_GPIO23 (0xfa0025ee): 0x010b -> 0x0104
MUX: setup AE2_34XX_MMC2_CLK (0xfa002158): 0x011c -> 0x0118
MUX: setup AG5_34XX_MMC2_CMD (0xfa00215a): 0x011c -> 0x0118
MUX: setup AH5_34XX_MMC2_DAT0 (0xfa00215c): 0x011c -> 0x0118
MUX: setup AH4_34XX_MMC2_DAT1 (0xfa00215e): 0x011c -> 0x0118
MUX: setup AG4_34XX_MMC2_DAT2 (0xfa002160): 0x011c -> 0x0118
MUX: setup AF4_34XX_MMC2_DAT3 (0xfa002162): 0x011c -> 0x0118
MUX: setup AE4_34XX_MMC2_DAT4 (0xfa002164): 0x011c -> 0x0118
MUX: setup AH3_34XX_MMC2_DAT5 (0xfa002166): 0x011c -> 0x0118
regulator: VUSB1V5: 1500 mV normal standby
regulator: VUSB1V8: 1800 mV normal standby
regulator: VUSB3V1: 3100 mV normal standby
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
regulator: VMMC1: 1850 <--> 3150 mV normal standby
regulator: VDAC: 1800 mV normal standby
regulator: VPLL2: 1800 mV normal standby
regulator: VSIM: 1800 <--> 3000 mV normal standby
i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
        (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
        (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
        (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
Switching to clocksource 32k_counter
musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
ashmem: initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 473
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler cfq registered (default)
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
loop: module loaded
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit)
cmdlinepart partition parsing not available
Creating 5 MTD partitions on "omap2-nand":
0x000000000000-0x000000080000 : "X-Loader"
0x000000080000-0x000000260000 : "U-Boot"
0x000000260000-0x000000280000 : "U-Boot Env"
0x000000280000-0x000000680000 : "Kernel"
0x000000680000-0x000010000000 : "File System"
UBI: attaching mtd4 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd4 to ubi0
UBI: MTD device name:            "File System"
UBI: MTD device size:            249 MiB
UBI: number of good PEBs:        1996
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 1996
UBI: number of PEBs reserved for bad PEB handling: 19
UBI: max/mean erase counter: 1/0
UBI: image sequence number: 1597711511
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
UBI: background thread "ubi_bgt0d" started, PID 404
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: �Љ
usb usb1: Manufacturer: �Љ
usb usb1: SerialNumber: �Љ
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.5.0:USB FTDI Serial Converters Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
android init
android_probe pdata: c0459464
android_bind
android_usb gadget: android_usb ready
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: �Љ
usb usb2: Manufacturer: �Љ
usb usb2: SerialNumber: �Љ
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
f_adb init
android_register_function adb
adb_bind_config
f_mass_storage init
android_register_function usb_mass_storage
mice: PS/2 mouse device common for all mice
using rtc device, twl4030_rtc, for alarms
twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
twl4030_rtc twl4030_rtc: Power up reset detected.
twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC.
i2c /dev entries driver
Linux video capture interface: v2.00
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCILL protocol initialized
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
logger: created 64K log 'log_system'
Advanced Linux Sound Architecture Driver Version 1.0.21.
No device for DAI twl4030
No device for DAI twl4030 Voice
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
OMAP3 Beagle/Devkit8000 SoC init
usb 1-2: new high speed USB device using ehci-omap and address 2
TWL4030 Audio Codec init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
ALSA device list:
  #0: omap3beagle (twl4030)
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Bluetooth: L2CAP ver 2.14
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
lib80211: common routines for IEEE802.11 drivers
Power Management for TI OMAP3.
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
fbcvt: 1024x768@60: CVT Name - .786M3-R
usb 1-2: New USB device found, idVendor=17e9, idProduct=401a
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2: Product: mimo inc
usb 1-2: Manufacturer: DisplayLink
usb 1-2: SerialNumber: 9000078
Console: switching to colour frame buffer device 128x48
usb 1-2: configuration #1 chosen from 1 choice
regulator_init_complete: incomplete constraints, leaving VDVI on
regulator_init_complete: incomplete constraints, leaving VDAC on
twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
generic-usb 0003:17E9:401A.0001: claimed by neither input, hiddev nor hidraw
android_usb gadget: high speed config #1: android
UBIFS: recovery needed
mmc0: new high speed SD card at address 0003
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size:   253145088 bytes (247212 KiB, 241 MiB, 1962 LEBs)
UBIFS: journal size:       9033728 bytes (8822 KiB, 8 MiB, 71 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:11.
Freeing init memory: 128K
Warning: unable to open an initial console.
mmcblk0: mmc0:0003 SD2GB 1.83 GiB
 mmcblk0: p1 p2
input: Fake Touchscreen as /devices/virtual/input/input0
# enabling adb
warning: `rild' uses 32-bit capabilities (legacy support in use)
adb_open
android_usb gadget: high speed config #1: android

#