U-Boot 2013.04-00042-g3bfbc1c (Aug 06 2013 - 18:31:47)

CPU:   Freescale i.MX6Q rev1.2 at 792 MHz
CPU:   Temperature 44 C, calibration data: 0x58852b69
Reset cause: POR
Board: MX6Q-gk802
DRAM:  1 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment

enable_hdmi: setup HDMI monitor
Display: HDMI (1024x768)
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0
U-Boot >  env set bootargs 'console=ttymxc3,115200 fixrtc noinitrd rootwait '
U-Boot > env set bootargs ${bootargs} 'root=/dev/mmcblk0p1  '
U-Boot > env set uimage '/boot/zImage'
U-Boot > env set fdt '/boot/imx6q-gk802.dtb'
U-Boot > env set fdtaddr  0x11e00000
U-Boot > env set bootdev 'mmc 1:1'
U-Boot > load ${bootdev} ${loadaddr} ${uimage}
4301688 bytes read in 338 ms (12.1 MiB/s)
U-Boot > load ${bootdev} ${fdtaddr} ${fdt}
24657 bytes read in 100 ms (240.2 KiB/s)
U-Boot > bootz ${loadaddr} - ${fdtaddr}
## Flattened Device Tree blob at 11e00000
   Booting using the fdt blob at 0x11e00000
   Loading Device Tree to 4f569000, end 4f572050 ... OK

Starting kernel ...

Booting Linux on physical CPU 0x0
Linux version 3.11.0+ ([email protected]) (gcc version 4.8.2 20130805 (prerelease) (crosstool-NG linaro-1.13.1-4.8-2013.08 - Linaro GCC 2013
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Freescale i.MX6 Quad/DualLite (Device Tree), model: Zealz GK802
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 7 pages/cpu @81007000 s7680 r8192 d12800 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096
Kernel command line: console=ttymxc3,115200 fixrtc noinitrd rootwait root=/dev/mmcblk0p1
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1031204K/1048576K available (5459K kernel code, 272K rwdata, 1700K rodata, 315K init, 373K bss, 17372K reserved)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xc0800000 - 0xff000000   (1000 MB)
    lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
    modules : 0x7f000000 - 0x80000000   (  16 MB)
      .text : 0x80008000 - 0x80705edc   (7160 kB)
      .init : 0x80706000 - 0x80754e00   ( 316 kB)
      .data : 0x80756000 - 0x8079a240   ( 273 kB)
       .bss : 0x8079a240 - 0x807f7864   ( 374 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 65075ms
CPU identified as i.MX6Q, silicon rev 1.2
Console: colour dummy device 80x30
Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x8055afd0 - 0x8055b040
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU2: Booted secondary processor
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
CPU3: Booted secondary processor
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
Brought up 4 CPUs
SMP: Total of 4 processors activated (6324.22 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered
vdd1p1: 800 <--> 1375 mV at 1100 mV
vdd3p0: 2800 <--> 3150 mV at 3000 mV
vdd2p5: 2000 <--> 2750 mV at 2400 mV
cpu: 725 <--> 1450 mV at 1150 mV
vddpu: 725 <--> 1450 mV
vddsoc: 725 <--> 1450 mV at 1200 mV
syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
bio: create slab <bio-0> at 0
mxs-dma 110000.dma-apbh: initialized
3P3V: 3300 mV
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c i2c-0: IMX I2C adapter registered
i2c i2c-1: IMX I2C adapter registered
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
PTP clock support registered
Advanced Linux Sound Architecture Driver Initialized.
Switched to clocksource mxc_timer1
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 2014
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
imx-sdma 20ec000.sdma: initialized
Serial: IMX driver
imx-uart 21e8000.serial: failed to get default pinctrl: -19
21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 61) is a IMX
console [ttymxc3] enabled
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-mxc: Freescale On-Chip EHCI Host driver
usbcore: registered new interface driver usb-storage
platform 2184000.usb: Driver imx_usb requests probe deferral
platform 2184200.usb: Driver imx_usb requests probe deferral
mousedev: PS/2 mouse device common for all mice
snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc0
i2c /dev entries driver
imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: no vqmmc regulator found
mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
mmc1: no vqmmc regulator found
mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[drm] No driver support for vblank timestamp query.
[drm] Initialized imx-drm 1.0.0 20120507 on minor 0
imx-ipuv3 2400000.ipu: IPUv3H probed
imx-ipuv3 2800000.ipu: IPUv3H probed
mmc0: host does not support reading read-only switch. assuming write-enable.
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Key type dns_resolver registered
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
mmc0: new high speed SDHC card at address aaaa
mmcblk0: mmc0:aaaa SU08G 7.40 GiB
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
 mmcblk0: p1
ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ci_hdrc ci_hdrc.1: EHCI Host Controller
ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
mmc1: host does not support reading read-only switch. assuming write-enable.
mmc1: new high speed SD card at address 0002
mmcblk1: mmc1:0002       482 MiB
input: gpio-keys.11 as /devices/gpio-keys.11/input/input0
snvs_rtc 20cc034.snvs-rtc-lp: setting system clock to 1970-01-01 00:00:00 UTC (0)
imx-drm imx-drm: No connectors reported connected with modes
 mmcblk1: p1
[drm] Cannot find any crtc or sizes - going 1024x768
Console: switching to colour frame buffer device 128x48
imx-drm imx-drm: fb0:  frame buffer device
imx-drm imx-drm: registered panic notifier
ALSA device list:
  No soundcards found.
VFS: Mounted root (ext2 filesystem) readonly on device 179:1.
devtmpfs: mounted
Freeing unused kernel memory: 312K (80706000 - 80754000)
INIT: version 2.88 booting
usb 1-1: new low-speed USB device number 2 using ci_hdrc
input: Lenovo Multimedia Remote with Keyboard N5902 as /devices/soc.0/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1:1.0/input/input1
hid-generic 0003:17EF:602B.0001: input: USB HID v1.11 Keyboard [Lenovo Multimedia Remote with Keyboard N5902] on usb-ci_hdrc.0-1/input0
input: Lenovo Multimedia Remote with Keyboard N5902 as /devices/soc.0/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1:1.1/input/input2
hid-generic 0003:17EF:602B.0002: input: USB HID v1.11 Mouse [Lenovo Multimedia Remote with Keyboard N5902] on usb-ci_hdrc.0-1/input1
Starting udev
udevd[87]: starting version 182
imx-sdma 20ec000.sdma: firmware not found
Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or directory
bootlogd.
Populating dev cache
ALSA: Restoring mixer settings...
/usr/sbin/alsactl: load_state:1729: No soundcards found...
Configuring network interfaces... eth0: ERROR while getting interface flags: No such device
Starting rpcbind daemon...done.
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
Sat Aug 10 14:52:00 UTC 2013
Starting atd: OK
INIT: Entering runlevel: 5
Starting system message bus: dbus.
Starting OpenBSD Secure Shell server: sshd
  generating ssh RSA key...
  generating ssh ECDSA key...
  generating ssh DSA key...
done.
Starting advanced power management daemon: No APM support in kernel
(failed.)
creating NFS state directory: done
starting 8 nfsd kernel threads: rpc.nfsd: Unable to access /proc/fs/nfsd errno 2 (No such file or directory).
Please try, as root, 'mount -t nfsd nfsd /proc/fs/nfsd' and then restart rpc.nfsd to correct the problem
done
starting mountd: done
starting statd: done
Starting system log daemon...0
Starting kernel log daemon...0
Starting internet superserver: xinetd.
Starting Telephony daemon
Starting Linux NFC daemon
Starting Lighttpd Web Server: lighttpd.
cups: started scheduler.
Starting crond: OK
imx-audio: setting default mixer settings.
amixer: Mixer attach default error: No such file or directory
amixer: Mixer attach default error: No such file or directory
amixer: Mixer attach default error: No such file or directory
amixer: Mixer attach default error: No such file or directory
amixer: Mixer attach default error: No such file or directory
Stopping Bootlog daemon: bootlogd.
umount: /mnt/.psplash: target is busy.
        (In some cases useful info about processes that use
         the device is found by lsof(8) or fuser(1))

Poky Next (Yocto Project Reference Distro) 1.4+snapshot-20130810 gk802 /dev/ttymxc3

gk802 login: