Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot SPL 2013.04-07297-g20bd663 (Jun 15 2013 - 03:08:59)
- Board: A20-OLinuXino_MICRO
- DRAM: 512MB
- CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
- SUNXI SD/MMC: 0
- U-Boot 2013.04-07297-g20bd663 (Jun 15 2013 - 03:08:59) Allwinner Technology
- CPU: Allwinner A20 (SUN7I)
- Board: A20-OLinuXino_MICRO
- I2C: ready
- DRAM: 512 MiB
- MMC: SUNXI SD/MMC: 0
- In: serial
- Out: serial
- Err: serial
- Net: emac
- Hit any key to stop autoboot: 0
- reading script.bin
- 43532 bytes read in 10 ms (4.2 MiB/s)
- reading uImage
- 2995072 bytes read in 137 ms (20.8 MiB/s)
- ## Booting kernel from Legacy Image at 48000000 ...
- Image Name: Linux-3.3.0+
- Created: 2013-06-15 21:44:23 UTC
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 2995008 Bytes = 2.9 MiB
- Load Address: 40008000
- Entry Point: 40008000
- Verifying Checksum ... OK
- Loading Kernel Image ... OK
- OK
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0
- [ 0.000000] Linux version 3.3.0+ (rz2k@Thessia) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #8 SMP PREEMPT Sun Jun 16 01:44:06 MSK 2013
- [ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c53c7d
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000] Machine: sun7i
- [ 0.000000] [sun7i_fixup]: From boot, get meminfo:
- [ 0.000000] Start: 0x40000000
- [ 0.000000] Size: 512MB
- [ 0.000000] bootconsole [earlycon0] enabled
- [ 0.000000] memory reserved(in bytes):
- [ 0.000000] : 0x43000000, 0x00010000
- [ 0.000000] : 0x52000000, 0x00010000
- [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
- [ 0.000000] [scu_get_core_count] cores=1800001
- [ 0.000000] sun7i_init_early: enter
- [ 0.000000] PERCPU: Embedded 7 pages/cpu @d0485000 s5632 r8192 d14848 u32768
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 84864
- [ 0.000000] Kernel command line: console=/dev/ttyS0,115200 root=/dev/mmcblk0p2 rootwait loglevel=7 earlyprintk=1
- [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000] Memory: 64MB 272MB = 336MB total
- [ 0.000000] Memory: 332556k/332556k available, 191732k reserved, 0K highmem
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
- [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
- [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
- [ 0.000000] .text : 0xc0008000 - 0xc056a554 (5514 kB)
- [ 0.000000] .init : 0xc056b000 - 0xc0593600 ( 162 kB)
- [ 0.000000] .data : 0xc0594000 - 0xc05db320 ( 285 kB)
- [ 0.000000] .bss : 0xc05db344 - 0xc0622bc0 ( 287 kB)
- [ 0.000000] Preemptible hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:160
- [ 0.000000] aw_clkevt_init: timer base 0xe0800c00
- aw_clkevt_init: sun7i_timer0_clockevent mult 6442450, max_delta_ns 170000, min_delta_ns 1000, cpumask 0xc03ff850, irq 54
- [ 0.000000] aw_clksrc_init(96)
- [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
- [ 0.000000] aw_clksrc_init(120)
- [ 0.000000] Architected local timer running at 24.00MHz.
- [ 0.000000] Console: colour dummy device 80x30
- [ 0.012888] Calibrating delay loop... 1915.28 BogoMIPS (lpj=9576448)
- [ 0.069701] pid_max: default: 32768 minimum: 301
- [ 0.071790] Mount-cache hash table entries: 512
- [ 0.076618] CPU: Testing write buffer coherency: ok
- [ 0.081070] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
- [ 0.086519] Setting up static identity map for 0x403fcd60 - 0x403fcdb8
- [ 0.199688] CPU1: Booted secondary processor
- [ 0.256687] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
- [ 0.256768] Brought up 2 CPUs
- [ 0.263987] SMP: Total of 2 processors activated (3830.57 BogoMIPS).
- [ 0.271341] devtmpfs: initialized
- [ 0.277729] [gpio-inf] aw gpio init start
- [ 0.277766] [gpio-err] gpio_clk_init: apb pio clk handle not NULL
- [ 0.283658] [gpio-err] gpio_clk_init: get apb pio clk failed
- [ 0.289311] [gpio-err] aw_gpio_init: gpio clk init failed
- [ 0.294673] gpiochip_add: registered GPIOs 0 to 17 on device: GPA
- [ 0.300747] gpiochip_add: registered GPIOs 24 to 47 on device: GPB
- [ 0.306885] gpiochip_add: registered GPIOs 54 to 78 on device: GPC
- [ 0.313046] gpiochip_add: registered GPIOs 85 to 112 on device: GPD
- [ 0.319279] gpiochip_add: registered GPIOs 119 to 130 on device: GPE
- [ 0.325611] gpiochip_add: registered GPIOs 137 to 142 on device: GPF
- [ 0.331931] gpiochip_add: registered GPIOs 149 to 160 on device: GPG
- [ 0.338265] gpiochip_add: registered GPIOs 167 to 194 on device: GPH
- [ 0.344585] gpiochip_add: registered GPIOs 201 to 222 on device: GPI
- [ 0.351489] kworker/u:0 used greatest stack depth: 6568 bytes left
- [ 0.357072] [gpio-inf] aw gpio init done
- [ 0.361124] script_init enter!
- [ 0.364858] script_init exit!
- [ 0.368645] print_constraints: dummy:
- [ 0.371392] NET: Registered protocol family 16
- [ 0.375534] [ccu-dbg] ccu_sysfs_init successfully
- [ 0.383082] sun7i_init: enter
- [ 0.383492] [ccu-inf] aw clock manager init
- [ 0.386877] [ccu-inf] aw_ccu_init
- [ 0.390376] [ccu-inf] script config pll3 to 297MHz
- [ 0.395128] [ccu-dbg] clk_enable: video_pll0 is enabled, count #1
- [ 0.401011] [ccu-dbg] clk_set_rate: set video_pll0 rate to 297000000, actual rate is 297000000
- [ 0.409703] [ccu-inf] script config pll4 to 300MHz
- [ 0.414352] [ccu-dbg] clk_enable: ve_pll is enabled, count #1
- [ 0.420083] [ccu-dbg] clk_set_rate: set ve_pll rate to 300000000, actual rate is 312000000
- [ 0.428304] [ccu-inf] script config pll6 to 600MHz
- [ 0.433303] [ccu-dbg] clk_enable: sata_pll is enabled, count #1
- [ 0.438969] [ccu-dbg] clk_set_rate: set sata_pll rate to 600000000, actual rate is 600000000
- [ 0.447380] [ccu-inf] script config pll7 to 297MHz
- [ 0.452138] [ccu-dbg] clk_enable: video_pll1 is enabled, count #1
- [ 0.458223] [ccu-dbg] clk_set_rate: set video_pll1 rate to 297000000, actual rate is 297000000
- [ 0.466784] [ccu-inf] script config pll8 to 336MHz
- [ 0.471567] [ccu-dbg] clk_enable: gpu_pll is enabled, count #1
- [ 0.477360] [ccu-dbg] clk_set_rate: set gpu_pll rate to 336000000, actual rate is 336000000
- [ 0.485761] [ccu-dbg] clk_enable: ahb_dma is enabled, count #1
- [ 0.492130] axp config [pmu_para] [pmu_used] : 1
- [ 0.496115] axp config [pmu_para] [pmu_twi_id] : 0
- [ 0.500848] axp config [pmu_para] [pmu_irq_id] : 32
- [ 0.505697] axp config [pmu_para] [pmu_twi_addr] : 52
- [ 0.510797] axp config [pmu_para] [pmu_battery_rdc] : 171
- [ 0.516098] axp config [pmu_para] [pmu_battery_cap] : 2700
- [ 0.521567] axp config [pmu_para] [pmu_init_chgcur] : 300
- [ 0.526931] axp config [pmu_para] [pmu_suspend_chgcur] : 1000
- [ 0.532660] axp config [pmu_para] [pmu_resume_chgcur] : 300
- [ 0.538199] axp config [pmu_para] [pmu_shutdown_chgcur] : 1000
- [ 0.544012] axp config [pmu_para] [pmu_init_chgvol] : 4200
- [ 0.549465] axp config [pmu_para] [pmu_init_chgend_rate] : 15
- [ 0.555207] axp config [pmu_para] [pmu_init_chg_enabled] : 1
- [ 0.560819] axp config [pmu_para] [pmu_init_adc_freq] : 100
- [ 0.566372] axp config [pmu_para] [pmu_init_adc_freqc] : 100
- [ 0.571998] axp config [pmu_para] [pmu_init_chg_pretime] : 50
- [ 0.577725] axp config [pmu_para] [pmu_init_chg_csttime] : 720
- [ 0.583525] axp config [pmu_para] [pmu_bat_para1] : 0
- [ 0.588559] axp config [pmu_para] [pmu_bat_para2] : 0
- [ 0.593578] axp config [pmu_para] [pmu_bat_para3] : 0
- [ 0.598610] axp config [pmu_para] [pmu_bat_para4] : 0
- [ 0.603632] axp config [pmu_para] [pmu_bat_para5] : 5
- [ 0.608664] axp config [pmu_para] [pmu_bat_para6] : 11
- [ 0.613771] axp config [pmu_para] [pmu_bat_para7] : 13
- [ 0.618890] axp config [pmu_para] [pmu_bat_para8] : 15
- [ 0.623998] axp config [pmu_para] [pmu_bat_para9] : 19
- [ 0.629117] axp config [pmu_para] [pmu_bat_para10] : 32
- [ 0.634311] axp config [pmu_para] [pmu_bat_para11] : 50
- [ 0.639517] axp config [pmu_para] [pmu_bat_para12] : 58
- [ 0.644711] axp config [pmu_para] [pmu_bat_para13] : 71
- [ 0.649917] axp config [pmu_para] [pmu_bat_para14] : 81
- [ 0.655111] axp config [pmu_para] [pmu_bat_para15] : 89
- [ 0.660317] axp config [pmu_para] [pmu_bat_para16] : 100
- [ 0.665598] axp config [pmu_para] [pmu_usbvol_limit] : 1
- [ 0.670891] axp config [pmu_para] [pmu_usbvol] : 4000
- [ 0.675911] axp config [pmu_para] [pmu_usbcur_limit] : 0
- [ 0.681204] axp config [pmu_para] [pmu_usbcur] : 0
- [ 0.685965] axp config [pmu_para] [pmu_pwroff_vol] : 3300
- [ 0.691344] axp config [pmu_para] [pmu_pwron_vol] : 2900
- [ 0.696624] axp config [target] [dcdc2_vol] : 1400
- [ 0.701397] axp config [target] [dcdc3_vol] : 1250
- [ 0.706157] axp config [target] [ldo2_vol] : 3000
- [ 0.710837] axp config [target] [ldo3_vol] : 2800
- [ 0.715526] axp config [target] [ldo4_vol] : 2800
- [ 0.720198] axp config [pmu_para] [pmu_pekoff_time] : 6000
- [ 0.725664] axp config [pmu_para] [pmu_pekoff_en] : 1
- [ 0.730685] axp config [pmu_para] [pmu_peklong_time] : 1500
- [ 0.736237] axp config [pmu_para] [pmu_pwrok_time] : 64
- [ 0.741432] axp config [pmu_para] [pmu_pwrnoe_time] : 2000
- [ 0.746897] axp config [pmu_para] [pmu_intotp_en] : 1
- [ 0.751918] axp config [pmu_para] [pmu_pekon_time] : 1000
- [ 0.762101] kworker/u:0 used greatest stack depth: 6416 bytes left
- [ 0.792959] bio: create slab <bio-0> at 0
- [ 0.795104] SCSI subsystem initialized
- [ 0.796021] usbcore: registered new interface driver usbfs
- [ 0.801133] usbcore: registered new interface driver hub
- [ 0.806081] usbcore: registered new device driver usb
- [ 0.813330] [ccu-dbg] clk_enable: apb_twi0 is enabled, count #1
- [ 0.816735] [ccu-dbg] clk_enable: twi0 is enabled, count #1
- [ 0.822366] [ccu-dbg] clk_reset: twi0 reset done
- [ 0.826880] [ccu-dbg] clk_get_rate: twi0 current rate is 24000000
- [ 0.833898] -------------------------------------------
- [ 0.838140] axp_mfd_probe:axp20_mfd pmu probed !
- [ 0.842731] -------------------------------------------
- [ 0.850460] axp_mfd 0-0034: AXP (CHIP ID: 0x21) detected
- [ 0.853904] -------------------------------------------
- [ 0.858437] axp_mfd_probe:axp20_mfd pmu request_irq ok !
- [ 0.863705] -------------------------------------------
- [ 0.870723] I2C: i2c-0: sun7i I2C adapter
- [ 0.872892] **********start************
- [ 0.876705] 0x40
- [ 0.878611] 0xf8
- [ 0.880577] 0x58
- [ 0.882425] 0x0
- [ 0.884244] 0x0
- [ 0.886064] **********end************
- [ 0.889840] [ccu-dbg] clk_enable: apb_twi1 is enabled, count #1
- [ 0.895677] [ccu-dbg] clk_enable: twi1 is enabled, count #1
- [ 0.901147] [ccu-dbg] clk_reset: twi1 reset done
- [ 0.905763] [ccu-dbg] clk_get_rate: twi1 current rate is 24000000
- [ 0.912084] I2C: i2c-1: sun7i I2C adapter
- [ 0.915943] **********start************
- [ 0.919608] 0x40
- [ 0.921511] 0xf8
- [ 0.923418] 0x58
- [ 0.925324] 0x0
- [ 0.927196] 0x0
- [ 0.928964] **********end************
- [ 0.932708] [ccu-dbg] clk_enable: apb_twi2 is enabled, count #1
- [ 0.938520] [ccu-dbg] clk_enable: twi2 is enabled, count #1
- [ 0.944046] [ccu-dbg] clk_reset: twi2 reset done
- [ 0.948652] [ccu-dbg] clk_get_rate: twi2 current rate is 24000000
- [ 0.954958] I2C: i2c-2: sun7i I2C adapter
- [ 0.958707] **********start************
- [ 0.962505] 0x40
- [ 0.964411] 0xf8
- [ 0.966318] 0x58
- [ 0.968224] 0x0
- [ 0.970111] 0x0
- [ 0.971866] **********end************
- [ 0.976118] print_constraints: axp20_ldo1: 1300 mV
- [ 0.982100] print_constraints: axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
- [ 0.988702] print_constraints: axp20_ldo3: 700 <--> 3500 mV at 2800 mV
- [ 0.995556] print_constraints: axp20_ldo4: 1250 <--> 3300 mV at 2800 mV
- [ 1.001932] print_constraints: axp20_buck2: 700 <--> 2275 mV at 1400 mV
- [ 1.008606] print_constraints: axp20_buck3: 700 <--> 3500 mV at 1250 mV
- [ 1.014660] print_constraints: axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
- [ 1.021496] gpiochip_add: registered GPIOs 229 to 233 on device: axp_pin
- [ 1.028213] Advanced Linux Sound Architecture Driver Version 1.0.24.
- [ 1.035516] Switching to clocksource arch_sys_counter
- [ 1.048712] cfg80211: Calling CRDA to update world regulatory domain
- [ 1.058911] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 1.060026] Line:1148:ohci_hcd_mod_init
- [ 1.063620] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 1.070024] line = 473,usb_manager_init
- [ 1.073585] [usb_manager]: CONFIG_USB_SW_SUN7I_USB0_OTG
- [ 1.078940] WRN:L211(drivers/usb/sun7i_usb/manager/usb_manager.c):ERR: get usbc(0) det_vbus gpio failed
- [ 1.088151] WRN:L242(drivers/usb/sun7i_usb/manager/usb_manager.c):ERR: get usbc0(usb_restrict) failed
- [ 1.098095] [sw_hcd0]: usb host driver initialize........
- [ 1.102815] [sw_hcd0]: open_usb_clock
- [ 1.106352] [ccu-dbg] clk_enable: ahb_usb0 is enabled, count #1
- [ 1.122248] [ccu-dbg] clk_enable: usb_phy is enabled, count #1
- [ 1.122443] [ccu-dbg] clk_enable: usb_phy0 is enabled, count #1
- [ 1.128337] [ccu-dbg] clk_reset: usb_phy0 reset done
- [ 1.143313] [sw_hcd0]: host_init_state = 0
- [ 1.143338] [sw_hcd0]: platform is usb host
- [ 1.146004] [sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 70
- [ 1.156356] sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
- [ 1.161729] sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
- [ 1.170521] hub 1-0:1.0: USB hub found
- [ 1.173170] hub 1-0:1.0: 1 port detected
- [ 1.177069] wrn: hcd is not enable, need not start hcd
- [ 1.182708] [sw_hcd0]: sw_usb_host0_disable start
- [ 1.186840] -------sw_hcd0_soft_disconnect---------
- [ 1.191699] [sw_hcd_host0]: Set USB Power OFF
- [ 1.196030] wrn: hcd is not enable, need not stop hcd
- [ 1.201176] [sw_hcd0]: close_usb_clock
- [ 1.204783] [ccu-dbg] clk_reset: usb_phy0 reset done
- [ 1.209737] [ccu-dbg] clk_disable: usb_phy0 is disabled, count #0
- [ 1.215788] [ccu-dbg] clk_disable: usb_phy is disabled, count #0
- [ 1.221780] [ccu-dbg] clk_disable: ahb_usb0 is disabled, count #0
- [ 1.227832] [sw_hcd0]: sw_usb_host0_disable end
- [ 1.232536] [sw_udc]: udc_init: version 20080411
- [ 1.237761] NET: Registered protocol family 2
- [ 1.241640] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 1.249182] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
- [ 1.256210] TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
- [ 1.262318] TCP: Hash tables configured (established 16384 bind 16384)
- [ 1.268486] TCP reno registered
- [ 1.271651] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 1.277442] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 1.284356] NET: Registered protocol family 1
- [ 1.288619] RPC: Registered named UNIX socket transport module.
- [ 1.293919] RPC: Registered udp transport module.
- [ 1.298583] RPC: Registered tcp transport module.
- [ 1.303233] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 1.309979] sunxi_reg_init enter
- [ 1.313360] [ccu-dbg] clk_get_rate: core_pll current rate is 960000000
- [ 1.319437] [ccu-dbg] clk_get_rate: cpu current rate is 960000000
- [ 1.325423] [ccu-dbg] clk_get_rate: axi current rate is 320000000
- [ 1.331506] [ccu-dbg] clk_get_rate: ahb current rate is 160000000
- [ 1.337556] [ccu-dbg] clk_get_rate: apb current rate is 80000000
- [ 1.343583] [cpu_freq] INF:sunxi_cpufreq_initcall: clocks pll=960000000,cpu=960000000,axi=320000000,ahp=160000000,apb=80000000
- [ 1.354977] [cpu_freq] INF:try to get regulator(0xdf936a80) successed.
- [ 1.361809] [cpu_freq] INF:-------------------V-F Table-------------------
- [ 1.368235] [cpu_freq] INF: voltage = 1450mv frequency = 1008MHz
- [ 1.374315] [cpu_freq] INF: voltage = 1400mv frequency = 912MHz
- [ 1.380420] [cpu_freq] INF: voltage = 1300mv frequency = 864MHz
- [ 1.386433] [cpu_freq] INF: voltage = 1200mv frequency = 720MHz
- [ 1.392513] [cpu_freq] INF: voltage = 1100mv frequency = 528MHz
- [ 1.398575] [cpu_freq] INF: voltage = 1000mv frequency = 312MHz
- [ 1.404633] [cpu_freq] INF: voltage = 1000mv frequency = 144MHz
- [ 1.410708] [cpu_freq] INF: voltage = 1000mv frequency = 0MHz
- [ 1.416766] [cpu_freq] INF:-----------------------------------------------
- [ 1.423628] [cpu_freq] INF:sunxi_cpufreq_initcall, get cpu frequency from sysconfig, max freq: 912MHz, min freq: 60MHz
- [ 1.434284] [ccu-dbg] clk_get_rate: core_pll current rate is 960000000
- [ 1.440783] [ccu-dbg] clk_get_rate: cpu current rate is 960000000
- [ 1.446842] [ccu-dbg] clk_get_rate: axi current rate is 320000000
- [ 1.452921] [ccu-dbg] clk_get_rate: ahb current rate is 160000000
- [ 1.458987] [ccu-dbg] clk_get_rate: apb current rate is 80000000
- [ 1.464956] [cpu_freq] DBG:cur: pll=960000000, cpudiv=1, axidiv=3, ahbdiv=2, apb=2
- [ 1.472522] [ccu-dbg] clk_get_rate: cpu current rate is 960000000
- [ 1.478701] [ccu-dbg] clk_get_rate: cpu current rate is 960000000
- [ 1.484643] [pm]aw_pm_init!
- [ 1.487401] standby_mode = 1.
- [ 1.490449] cpu0_en = 0.
- [ 1.492946] dram_selfresh_en = 1.
- [ 1.496241] wakeup src cnt is : 0.
- [ 1.499724] [wifi]: select wifi: rtl8188eu !!
- [ 1.504427] [rtl8188eu]: exec rtl8188eu_wifi_gpio_init
- [ 1.509188] [rtl8188eu]: module power name
- [ 1.513312] [rtl8188eu]: rtl8188eu module power set by axp.
- [ 1.518920] [rtl8188eu]: get power regulator failed.
- [ 1.523821] [wifi_pm]: wifi gpio init is OK !!
- [ 1.532155] msgmni has been set to 649
- [ 1.533005] io scheduler noop registered
- [ 1.535848] io scheduler deadline registered (default)
- [ 1.550745] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
- [p
- [
- [
- 5
- [
- [
- [
- [
- [
- [
- [
- [
- [k6
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [
- ci:
- [
- [
- [
- [
- [5R
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [n
- 3
- [
- [,
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [3
- [0
- [1
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [
- [.
- [
- [
- [
- [v
- [
- [
- [
- [
- [
- [
- [
- []
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement