2009

Victim was inside a building bundling material and became ill, possible heat stroke.
Victim was on a scaffold doing repairs on an archway and the scaffold collapsed.
Victim was conducting roofing work, and fell through a hole in the roof, 25 feet to the concrete floor below.
Victim was climbing a ladder while servicing an air-conditioning unit and fell from the ladder.
Employees were throwing away old files. They had a dumpster on the forks in the raised position. In bringing the dumpster down on the forks, the load became unstable. Victim stood on the rear of the forklift to act as a counterbalance. The dumpster fell off the trucs, causing forktruck to lunge forward and the victim to strike his head on the overhead guard, falling to the ground.
Victim was pressure testing a new metering station at a new pipeline construction project, when an explosion occurred.
Victim was standing on the side of the road and was struck by a car.
Victim was working on a pole replacing a transformer, 14,400KV, and was electrocuted.
Victim was installing coax cable hangers down the face of an existing tower and fell 60 to 100 feet.
Victim was on a roof preparing an estimate. He started to come down from the roof and the ladder became dislodged. Victim fell 12 feet to the concrete driveway.
Victim was herding cattle for the feedlot from a horse. The horse stumbled and fell. Victim subsequently fell.
Victim was in the process of assembling a transition box, while removing the brace the box collapsed, crushing him.
Victim was installing an overhead garage door. He was using a truck-mounted generator/welder to generate power for his tools. He was found unresponsive in the bed of the truck. Victim was electrocuted.
Victim was working under a disabled truck, disconnecting the drive shaft. The vehicle fell, crushing him.
Victim was repairing a tote at the end of the line. The top tote fell over, crushing the victim.
Victim was working from the raised bucket of an aerial device. The boom and bucket fell to the ground.
Victim was on top of a railcar carrying elemental sulfur and was found unresponsive.
Victim was working from a raised forklift and fell to the ground.
Worker was replacing a breaker in a main panel at a saw mill and an arc blast occurred.
Worker was putting away a piece of lawn equipment and was stung twice by insects.
Worker was found on the ground with hot work gloves lying next to him, apparently electrocuted.
Worker fell from a roof.
Worker was in the process of loosening straps on a load of pipe located on a flatbed trailer.  The load shifted, causing the pipe to fall and strike the worker.
Worker was 12-feet high removing a roof truss and fell, striking his head on the front door concrete patio below.
Worker was working with an overhead crane and a bundle of 7-8 slabs of granite.  The slabs tipped over on the worker.
Worker was on the roof of a modular home being placed on pilings.  Lightning struck the roof, electrocuting the worker.
Worker was crushed in a chip grinder.
Worker was caught between the bucket of a backhoe and a wooden deck attached to a building.
Wenday South dba Wendy's, Dayton, OH  45459Worker was working in the kitchen near the back sink.  She slipped and fell in a wet spot, striking her head on the floor.
Worker was in an aerial lift pressure washing a building and was electrocuted after the lift contacted an overhead powerline.
Worker was electrocuted.
Worker was removing trim from a window and fell 30 feet from a ladder.
Worker was performing work on the forks of a forklift truck.  The forks fell, striking the worker on the head.
Employees were using a dozer to try and get an overturned all-terrain forklift back on its wheels.  They attached a synthetic strap with a shackle to pull the forklift and turn it upright.  The eye of the strap broke, striking the worker, who was in the cab.
Worker was working on a bucket truck repairing an exterior light fixture and fell 25 feet to the ground below.
Worker and another employee were closing a tap while clearing a branch from a downed powerline.  Worker was electrocuted.
While clearing a branch from a downed powerline.  Worker was electrocuted, and died after being hospitalized.
Worker was crushed by a tree that was being pulled down and back cut.
Worker was doing trash collection and was struck by oncoming traffic.
Worker was run over by a pickup truck.
Worker was stationary, being handed scaffold material from another employee  Worker collapsed after complaining about being woozy.
Worker was standing between a sewer bypass pump and an excavator.  The machine turned, crushing him between the excavator and the pump.
Worker was working on a pump in a magnesium recycling area.  He was in the process of turning a shaft with a pipe wrench to free up a vertical propeller when the hose connected to the pump either split or broke open.  The force of the steam blew him against a metal cage.
Worker was working under a lift truck performing maintenance.  The jacks failed and the lift truck fell on the worker.
Worker was standing on the back of a golf cart and fell off.  He was then run over by a truck.
Victim was standing beside a tractor trailer dump truck operating the dump controls, unloading gravel. The load and the body shifted, causing the trailer to rollover, crushing the victim.
Victim was completing electrical work from a ladder. He was shocked and fell 8 feet to the ground.
Victim was polishing a shaft. The shaft flew out and struck him on the chest.
Victim was noted to be somewhat disoriented and had a large knob on head.
Victim fell from a swing stage after the cable supports broke.
Victim fell 15 feet at an air freight terminal.
Victim fell 60 feet from a flat roof.
Victim was moving a large metal fixture with a bridge crane. The fixture slipped off the supports and crushed him.
Victim, during the repair/construction of building gutters, fell from a mechanical lift.
Victim was crushed by a skid steer bucket.
Victim was performing roofing operations. While removing a skylight on the roof, stepped into the open hole and fell.
Victim was returning to a job assignment and was struck by a yard-truck.
Victim was installing roof shingles from a 20-foot aluminum ladder, contracted an electrical service and fell from the ladder.
Victim was at the jobsite to inspect and fell from the scaffolding.
Eastcao Enterprises Incorporated, Myerstown, PA 17405Victim was cutting steel from an aerial lift and fell 7-8 feet to the floor below.
Employees were removing a cap on a 12-inch natural gas pipeline. Employees working nearby were doing some oxygen/acetylene cutting. While removing the cap, natural gas escaped and was ignited by the cutting process. One employee fatality and two employees were hospitalized.
Victim was unloading a palette of boxed flowers, and was struck on the torso, while pulling a box towards him. The stack of boxed fell, causing him to lose his balance, and fall backwards down 1'8 high.
Walt Disney World Lake Buena Vista, FL 32830Victim, during a choreographed sword fight, stumbled and fell into a wall.
Victim was found off his forklift, apparent heart attack.
Victim was picking up trash/debris along the roadside and was struck by a tire that had sheared off a truck axle.
Victim was struck on the head by a metal trench plate.
Victim was doing landscaping services. He was later found collapsed in the company truck, apparent heat stress.
Victim was surveying the ramp shoulder and was struck by an automobile.
Victim leaned across a horizontal milling machine turning at 138 RPM. One of the sleeves of his shirt was caught by either the spinning shaft or drift. Victim was pulled off the floor and wrapped around the shaft.
Victim was welding on an overhead interior structure of a water tank, and collapsed on the scaffold, possible heat stress.
Victim was pouring gasoline into a carburator of a truck, it backfired and covered the victim with buring gasoline.
Victim was working on the second floor, nailing in window jams. He fell out of the window, 13 feet to the ground.
Victim was working on a circuit breaker and received an electricl shock.
Victim was removing sheetrock and metal studs. He was electrocuted by exposed wires.
Victim died from a heat stroke.
Victim was removing a 5,000-pound valve using a 50-ton mobile truck crane. During the process, the valve came free from its rigging and fell through the scaffold platform that the victim was standing on. Both the valve and the victim fell 10 feet to the inside of the tank, with the valve pinning the victim to inside wall.
Victim fell 18 feet from a ladder jack scaffold.
Victim was operating a walk-behind stripe groover machine and was struck from behind by an errant vehicle.
Victim was working on a foundation of a single family residence. He collapsed outside the adjacent house.
VIctim was working from a ladder, repairing a pipe in the kitchen area, and fell from the ladder.
Victim was covering concrete with a burlap cover. The winds picked up the burlap cover, entagling the victim and pulled him off the bridge. He fell 18-20 feet to the dirt embankment below.
Victim was installing a ceiling light from a ladder and received an electrical shock from the light wiring. He fell 10 feet to the shop floor, stiking objects in the repair bay on his way down.
Victim was struck on the head by a traveling block of a ship-based crane.
Victim was performing tumbling and roll movements, made contact with another employee and afterwards exhibited difficulty breathing.
Victim was 140 feet inside a tunnel adjusting openings when the tunnel became filled with water. Victim drowned.
Victim was in a man-lift and was electrocuted.
Victim was driving a skid steer loader from a dumpster, suspended by a crane, at the 7th floor level of a building being demolished. He put the loader into reverse causing the suspended dumpster to swing away from the building, which resulted in the skid steer loader being thrown from the dumpster, falling to the ground below.
Victim was installing a new cable TV. While crawling under the house, came in contact with a bare wire, and was electrocuted.
Victim was preparing a piece of equipment for maintenance, and collapsed.
Victim fell five stories from a 2-point suspended scaffold after the cable broke.
Victim was on a ladder changing a light bulb, and fell.
Victim was operating a forklift. The forklift turned, tipped over, and pinned the victim.
Victim was blowing leaves and debris. The leaf blower he was using contacted an air conditioning unit. Victim was electrocuted.
Victim was performing welding operations and was electrocuted.
Victim was preparing a hover hookup and was struck by a snag or tree that had been dislodged b a helicopter rotor wash.
Victim was preparing a hover hookup and was struck by a snag or tree that had been dislodged b a helicopter rotor wash.
Victim was operating a lawn tractor and the tractor tipped over, rolling onto the victim.
Victim was working in an aerial lift upgrading three phases of an electrical distribution line. He was on the pole during the process of hoisting and moving the existing energized A phase and contacted energized conductors and was exposed to 7,620-volts of AC voltage. Victim was electrocuted.
Victim was installing asphalt shingles and fell 40 feet to the ground.
Victim was working from a basket lifted up by a rough terrain forklift that tipped over on its side.
Victim was working in the basket of an articulating truck mounted boom. During movement of the boom, victim was catapulted out of the basket.
Victim was assembling a stairway on the outside of a grain bin. He was stepping from the stairs to a metal ladder and suffered an attack, possible electric shock and fell to the ground.
Victim was pressure washing a vessel standing on a scaffold 15 to 20 feet, and fell.
Victim was working an outdoor sale at a store and was struck by a car, pinning the victim to the building.
Victim was performing drywall work and fell 9 feet from a tubular welded scaffold.
Victim was cleaning out a pit at a grain elevator. He was walking near the unguarded opening and fell through, 15-20 feet, to the bottom of the pit.
Victim was in a 60-foot high silo unclogging a discharge hole. While in the process of drilling a hole and remvoing the pipe, the victim clutched his chest and fell over.
Victim was moving a ladder and touched the overhead power line with the ladder. He was electrocuted.
Victim was working from an 8-foot step ladder doing caulking on a ceiling/wall area and fell to the ground.
Victim was operating a knuckle boom truck and was crushed between the boom and the controls.
Victim was struck and pinned by two track-hoes.
Victim was conducting service work on a coke vending machine and was electrocuted.
Victim fell from a 3-step ladder.
Victim, during a grinding operation, was struck by an exploding grinding wheel.
Employee was thrown from an asphalt roller while working on a road paving project (possible heart attack instead - more information will be provided after investigation).
Employee was involved in a bridge blasting and painting operation. Employee was wearing a harness but was not tied off to the horizontal lifeline. Fall from the elevated walkboard resulted in fatal injuries.
Employee was in the warehouse when a pallet of door panels stacked 15-feet high and weighing 850 lbs fell from the top of the stacked palets, crushing the employee.
Employee was working from a ladder and fell to the ground. Head injuries resulted in a fatality.
Employee was working with a gasoline powered scarifying machine. Probable cause of death was carbon monoxide poisoning.
Employee was observed hanging by his harness from the bridge of a Kone 60-ton crane. After rescue, the coroner reported the cause of death was electrocution.
Employee was below the elevator releasing the elevator jaws. The elevator dropped, crushing the employee.
Employee was installing a new tire. The explosive separation of the and its components resulted in fatal head injuries.
Employee was engaged in residential roofing work and fell 26 feet to his death.
Employee was struck by a derrick.
Employee operating a skid steer loader on a slope was killed when the skid stree loader rolled over.
Employee fell down the stairs. Stairs did not have a hand rail.
Employee was performing masonry work 250 feet above ground but was not wearing fall protection. Fall to the ground resulted in fatal injuries.
Employee suffered a fatal heart attack while observing fire fighting activities at the workplace.
Employee was aboard a vessel observing loading the compartment with calcined coke. He tripped over a coaming and struck his head on a vent pipe.
Worker was power washing hog crates when he fell to the floor and became non-responsive.
Employee was found unconscious at the base of a fixed ladder. Employee transported to hospital where he was pronounced dead.
Worker was crushed by a truck when it fell over on him while lowering a cut tree with the boom of the truck.
Worker was loading containers on a barge and was found crushed between the containers.
Western Engineering Company, Chappell, NE 69129Employees were working on a road construction project. The back set of duals came off a trailer and struck the employees. One employee fatality and one employee hospitalization.
Employee was pulling a pallet. The pallet broke causing the employee to fallbackwards, hitting his head against a metal door.
Employees were shutting down a natural gas well and flushing it with water. They disturbed a pocket of hydrogen sulfide and were overcome by the gas. One employee fatality and two employees were hospitalized.
Worker was caught between a dock plate and a truck's trailer.
Worker was making a connector from a store sign to a breaker panel and was electrocuted.
The Worker was found on the kitchen floor of the Edgewater Hotel & Casino. The Worker told a co-worker that he had collapsed on the floor. The co-worker went for help and when he returned the Worker was not responding. Attempts were made to revive him but he never responded.
Worker was standing on a scissor lift taking inventory and fell 5 feet, hitting his head on the cement below.
Worker was demolishing a concrete block wall when the wall collapsed striking the Worker resulting in crushing injuries which resulted in the fatality.
During culvert removal preparations the Worker placed himself in an excavation with no cave-in protection. The Worker was killed when a cave-in occurred.
Worker fell through a skylight.
Worker died as a result of being struck by a dead alder tree.
Worker during the erection of a communication tower fell 325 feet.
Worker was struck by a pipe, knocked under a V-Door and fell through the V-Door to a catwalk 20 feet below.
Worker was on a platform that collapsed, falling 25 feet.
Worker was reaching in to straighten up brick that had fallen over to one side for the setting head and was caught between the brick and the setting head.
Employees were attempting to raise a 14 x 26 framed wall by hand and the wind increased. The wall fell, crushing the Worker and hospitalizing another employee.
Worker was buried in a trench.
Worker was boarding a tow boat and fell into the water, drowning.
Worker was operating a Sakai Roller near the edge of a steep embankment and the Roller rolled off the embankment. The Worker jumped free and was crushed when the machine landed on top of him.
Worker fell down an elevator shaft to the basement.
Worker was struck by a piece of lumber he was working on that kicked back and struck him in the chest. Cause of death was blunt force trauma.
Worker was working under a front end loader utilizing a wooden block and a 20-ton bottle jack to lift a front end loader that fell, crushing the Worker.
Worker was working on a roof top performing some voltage testing on an exhaust fan. He fell 25.8 feet through the roof skylight, landing on the concrete inside the building.
Worker was working from a scissor lift replacing a ballast to light a fixture. In connecting the ballast wires to the energized wires, worker received a fatal electrical shock and was electrocuted.
Worker fell 8 ft, 10 inches from a scaffold landing on the concrete floor below.
Worker was driving an ATV and lost control of the vehicle, running it into a wall.
Worker was working with a strain of bacteria, and was complaining of shortness of breath and flu-like symptoms.
Worker was cutting a tree and the limb he was cutting fell on him causing him to fall 40 feet to the ground below.
Worker was welding and was struck by a piece of metal.
Worker fell off a mule, hitting his head on the gravel road.
Worker was delivering a package and was run over by a front end loader.
Worker was struck by a joist.
Worker was struck by an on-site dump truck.
Worker was cutting off a drum. The drum exploded.
Worker was removing an aerial drop and fell 20 feet from an extension ladder.
Worker was found between a forklift and a metal beam.
Worker fell and was run over by a bulldozer.
Worker was replacing a live line and wrecking out a couple of towers. Worker contacted a live line and was electrocuted.
Worker was in a manlift putting on an angle to a post and was found on the ground.
Worker was welding near or on a baler and was discovered entrapped in the baler.
Worker was engulfed in a corn storage bin. Emergency rescue services discovered the worker buried beneath the corn.
Worker was spotting a mobile home. The home slipped off the jack onto the worker.
Worker was installing a 7620-volt power line and was electrocuted.
Worker was cleaning poultry coops/bins and fell 18-20 feet off an extension ladder.

2010

Employees were installing roof trusses 20 feet from ground level, when 50 trusses fell in a domino effect crushing the employees. One employee fatality and to employees were hospitalized."
Employees were installing a tilt-wall into a trench. Decedent was inside the trench when the earth collapsed.
Weight Farm, Bellfonte, PA 16823",Decedent was inside a silo loading the feeder from a ladder. He became wedged within the ladder cage in a fetal position and suffocated.
The worker was assigned to perform irrigation maintenance work in an apartment complex. The worker was asked by a couple moving for help moving furniture. While moving a piece of furniture, the worker got on the truck, fell to the ground and hit his head. The worker was taken to the hospital where he died 14 days later."
Worker was run over by an intermodal container.
Worker was sandblasting under a bridge and fell 124-feet from a two-point suspension scaffold.
Worker was inside the engine compartment of a backhoe changing the filters and was struck by the counter weight of another backhoe.
Worker was loading a wild barrsinghuas into a holding pen. The animal gored the decedent in the leg and back.
Worker was putting in metal studs and was found on the scissor lift.
Worker was found unresponsive in the employee restroom.
Worker was assigned to check out a semi-trailer's front right air bag. While positioned between the two trailer axles, he was struck on the head by the left front air bag's base cup."
Worker was performing work on a gas drilling rig and was struck in the chest by a drill pipe.
Worker was carrying tools to the other side of a metal corrugated roof and fell 25-feet through one of the skylights.
Worker was performing welding duties aboard a marine vessel. An electrode from his welding equipment contacted the sweat on his neck, causing an electric shock."
Worker was electrocuted.
Worker was trimming trees and was electrocuted, after the aerial lift contacted an overhead powerline, causing the bucket truck to become energized."
Worker was operating a line 2 extrusion machine and was struck by a plug at the end of the line.
Worker was cleaning the hardened plastic from the mold. He was standing in between the mold plates when the machine started and was crushed between the mold plates.
Worker was cleaning a pizza oven and was found later, unresponsive in the break room."
Worker was locking down a shipping container to the bed of his truck and was struck by the rubber tire crane.
Werner Construction, Inc., Norfolk, NE 68701Worker was washing flights on an auger of a concrete machine and was pulled into the flights of the auger.
Worker was under a home doing plumbing work in a tunnel, dug under the concrete foundation using an electrical shovel type drill, and was electrocuted."
Worker was struck by a pipe cap in the back.
Employees were splicing a de-energized downed oil field line. The oil field line got into a 7300-volt line, electrocuting one worker."
Worker was changing a fluorescent overhead light and was electrocuted.
Worker fell 70-feet into a gap that was on the formwork while removing the excess plaster.
Worker was in the cage of an aerial lift with the boom extended 95-feet when the lift tipped over, falling to the ground."
Worker was carrying tiles on residential roof. He backed up into an overhead power line and was electrocuted.
Worker was investigating a water leak in a public stairwell between the 1st and 2nd decks. He opened a secured door leading to the exterior of the boat and fell through.
Worker was wrapping an 18,000-lb steel coil while the coil was on an exit coil cart. The steel coil came off from the cart and fall on the worker."
Worker was crushed between a truck and a building.
Worker was working in an unprotected trench installing a sewer/water line. A portion of the trench caved in, fully engulfing the worker and trapping another employee, who was hospitalized."
Worker was in the process of installing traffic counts and was hit by a motor vehicle.
Worker was working on a skid steer machine and was pinned between the arms of the machine and the machine frame.
Worker was performing roofing work on a low slope roof and fell through an unprotected skylight.
Village of Tarrytown Tarrytown, NY  10591",Two workers were killed from a possible fall and/or oxygen deficiency while entering a permit-required confined space manhole.
Worker was operating a small tractor that overturned and pinned him underneath.
Worker was operating an aerial lift and got caught between the lift and an overhead door's overhang.
Willoway Nurseries Inc., Huron, OH  44839Worker was operating his personal vehicle at a railroad crossing and was struck by a train.
Worker was crushed by a section of steel plate.
Worker was lighting up a gas furnace.  An explosion occurred and the worker was struck on the head by falling debris.
Worker was measuring a grade for the bridge brackets, outside the life-line system, on the I-64 bridge when he fell approximately 30 feet to the ground below.  He was wearing a fall protection harness, but was not tied off."
Worker without fall protection was replacing sections of a roof.  He fell through a 40-inch opening in the roof and down 31 feet to the ground.
Worker was operating crane when crane tipped.  Worker fell and was crushed between crane cab and a wall.
While changing and wiring two heaters, worker turned on electricity to check wiring.  He forgot to turn off the electricity and was electrocuted by 480 volts upon contact."
Wright Brothers Construction Company,Inc., Charleston, TN 37304",Worker lost control of an articulating dump truck at a landfill.  The truck flipped over, pinning the operator under the motor compartment."
Worker was holding end of the hose while pouring concrete from pump truck.  Truck's boom contacted overhead line, electrocuting worker."
Worker had parked a water tank truck on an incline.  While filling the truck's tank, the truck rolled down the incline and over the worker."
Worker was operating an earth roller that tipped and crushed him.
While worker was uncovering a sewer pipe with a shovel in a trench approximately 6 feet deep when the trench collapsed.
Worker was doing repairs on the roof of apartments using a 24-foot aluminum extension ladder. He descended from the ladder, stepping on the first step and fell 20-22 feet."
Worker was struck by a pick-up truck that was backing up from a warehouse.
Worker fell off a boarding ramp to a docked tug and drowned.
Worker was unloading a D76 Dozer and was trapped by the dozer.
Worker was waiting in line to be loaded out at a mill. He had exited his truck to check on something on the trailer in front of him. While doing so the truck pull forward. The trailer tires struck and traveled over the worker.
Wong Potatoes Inc., Merrill, OR 97603",The worker was run over by a trailer while harvesting onions.
Worker was using a hand-held grinder on floor bolts when sparks ignited flammable vapors in the area.
E & C Construction Oc., Newark, NJ 07104Worker fell 30-feet from a roof to the ground.
Worker was marking a roadway for striping operations and was struck by an automobile.
Worker was installing trimming and fell, hitting his head against the kitchen island."
Worker was doing construction operations and was struck by a road grader.
Worker was replacing a hydraulic cylinder which raised the hopper of a street sweeping vehicle. The decedent had raised the hopper and was working within the framework, when the hopper dropped, crushing the worker between the hopper and the framework."
Worker was struck/crushed by walls and roof of a building after a dump truck fell onto the building.
Worker was working in the attic space of a residential home securing a ventilation line and fell through the attic floor.
Worker was holding the lid of a derrick truck while the derrick was being raised. The derrick contacted overhead power transmission lines and the worker was electrocuted.
Worker was operating an excavator and was crushed after the wall collapsed on the excavator.
Worker was in the process of moving a scissor lift using a lull to move it from floor to floor. Worker entered the scissor lift to drive it off the forks, a portion of the concrete plank landed on the worker, who was in the scissor lift."
Worker was working on a light fixture from a ladder 15-feet above the ground and fell, possible shock."
Worker was sruck by an object that fell from a shelving rack.
Worker was dismantling a 40-foot high scaffold and fell.
Worker was unloading bulls from a truck into the chute. One bull kicked the gate, knocking the worker over, hitting his head on the concrete. There was traumatic head injury with brain swelling."
Worker was unloading a vessel and was struck by a loose spinning cargo sling chain.
Worker was crossing a street to get to a work zone and was struck by a motor vehicle.
Val-O-Mo Farm, Inc., Elmwood, WI 54740",Worker was operating a skid-steer cleaning out a dairy cattle barn near an outdoor manure slurry pit. The skid-steer and the worker fell off the end of the push-off platform into the manure slurry pit, trapping the worker in the vehicle. Worker died of suffocation due to inhalation of manure."
Worker was working alone replacing gutters, louver and other work prior to painting. The worker fell from a step ladder onto flat roof. The worker did not seek any medical attention at the time. The worker was found unresponsive that same night."
Worker was working from a mechanical mezzanine and fell 14-feet through a hole in the floor to the lower level.
While on lunch the worker suffered an asthma attack. The worker was taken to the hospital but did not survive.
Worker was flagging traffic in a road construction zone and was struck by a truck.
Worker was walking down steps from a utility room when he slipped or tripped.
Worker was delivering a fiberglass tank. He was retracting the knuckle boom on the crane back to travel position. The boom contracted a power line. Worker suffered injuries from electric shock.
Worker was on an aluminum extension ladder that had been extended 30-feet cutting limbs from a tree, lost his balance and fell."
Worker was working from scaffolding platform, while setting a ladder, lost his balance and fell through a 1-foot opening between the work platform and guardrail systems, 30-feet to the ground level."
Worker was performing maintenance on a tank area within the dry docked barge and upon exiting the area complained of experiencing breathing difficulties.
Worker was using a ladder to change a light bulb and fell from the ladder to the ground.
Worker was diving under water cleaning a pond and drowned.
WL Construction, Inc., Western Springs, IL 60558Worker was placing a stepladder over a stairwell to retrieve wood from a job built scaffold. Worker was standing on the ladder when the ladder shifted and fell 14-feet into the concrete stairwell.
Worker was setting steel beam in house foundation and making adjustments to level the beam. The beam dislodged from its support and fell onto the worker.
Workers were removing a tree by cutting the trunk into sections from an aerial bucket truck. The log was dropped 15 to 20-feet from the bucket, the worker operating the chipper had not cleared below and the log struck him on the head."
Worker was found on top of an air conditioning unit on a roof.
Worker fell 50-feet out of an Aerial Work Platform.
VNM Erector, Inc., Miami, FL 33126Worker was performing roadway repair and was struck by a vehicle.
William E. Lewis Logging, Inc., Greenville, NC 27834Worker was struck in the head by the top of a dead tree that was falling.
Worker was crushed by steam roller.
Wal-mart Store #58, Russellville, AR 72802",Worker was in the process of removing a box that contained a bicycle from a storage rack. He was standing on the second or third step of a step ladder. The box fell forward and he fell from the ladder, striking his head on the floor."
Worker was riding on a golf cart, stood up and fell, hitting his head."
Worker was backed over by bucket truck.
Worker fell from top of truck and later died 11/8/2009.
Worker was looking up at a box performing work activities and passed out, hitting his head."
Wal-mart Supercenter, Las Vegas, NV 89123",The worker collapsed in the dairy areas and was found unconscious and unresponsive by an employee. The worker was transported to the hospital where he was pronounced dead from an apparent heart attack.
Worker was elevated in an aerial lift that collapsed.
Egenolf dba Horner Industrial Services, Indianapolis, IN 46225Worker was working alone and found by other employees having either fallen into or been inadvertently crushed by a moving part on a piece of equipment.
Worker was removing a tarp from his pickup truck and was struck by a wheel end loader, crushing him."
Worker was performing duty in a grain bin and was engulfed by grain.
Worker was found caught up in a roll up machine that tolls up fiberglass insulation.
Worker was engaged in work activities including rough terrain forklift operations and construction work and was walking up an incline away from the Lull carrying a screw gun box and was struck by the right rear tire of the Lull.
Worker was deep in a trench wrapping fence wire around the roots of an oak tree being transplanted. The wire broke and he was caught in a cave-in.
Worker was re-roofing a home and while walking on the ridge of the roof, he slipped, falling to the deck below."
Worker fell through open catwalk.
Worker was christmas treeing three roof opening frames and the frame at the bottom of the rigging came off the hook, striking the worker."
Worker contracted H1N1 flu.
Worker was driving a tractor pulling wagons in sugarcane harvesting, went off the road into a canal, drowning."
Worker was fatally shot during the commission of a robbery.
Working at a private residence curring down trees, the worker was struck b a limb in the head and died."
Worker was in the process of removing a boom from a crane and knocked out 2 bottom pins from the heel section. The heel section came down, striking the worker."
Workers (2) were struck by a load being raised by a crane when rigging spreader came loose.
Enterprise Holdings, Weymouth, MA 02188Worker was crushed by an automobile that was rolling backwards.
Worker was setting foundation forms. An excavated dirt wall caved in, burying and crushing him."
Worker was riding a lead system when the crawler crane tipped over causing him to be thrown from a platform, striking the boom of the crane."
Worker was trapped and crushed by a concrete pallet.
Valcourt Building Services, Montclair, NJ 07044Worker was caulking an AC unit and fell off the balcony.
Worker was dumping waste from papermill site that is being torn down, when dump trailer made contact with power lines. The worker exited the truck cab and was electrocuted."
Elevating Boats LLC, Houma, LA 70363Worker was in a nearby workshop when the boom of a 200-ton crane collapsed into the workshop fatally injuring the worker.
Worker was struck by a van that was backing in.
Worker was unloading pipe and was crushed between the pipe and front end loader.
Worker was transferring granite slabs and a slab fell, crushing the worker."
West Selden Construction, Incorporated, Boston, MA 02122",Worker was in the process of climbing the frames of a scaffold to get to his work station and collapsed, falling 25-feet from the platform to the ground below."
Worker was standing along side his semi-trailer, as it was being unloaded by a powered industrial truck. A bundle of steel weighing 2700-pounds fell, striking him."
Worker was part of a land based oil rig & natural gas well drilling rig crew and contracted the H1N1 flu.
Worker was operating an order picker and struck a rack, which pushed a pallet of glass onto the order picker."
Worker was working the drilling board. A drill pipe came loose striking the worker on the head.
VT Halter Marine, Escatawpa, MSWorkers were using a thinner product to prepare the inner section of the bottom hull for painting. There was a fire/explosion killing two workers and hospitalizing two other workers.
Worker was in the process of installing a wireless point at a facility. He was using a 6-ft ladder to access the ceiling, fell backwards off the ladder, striking his head on the concrete floor."
Worker was crushed between a forklift and a parked flatbed truck.
Worker was performing detail work on a vehicle and ingested a wheel cleaning solution.
Worker fell off orchard picker ladder as he was ascending with an empty orange pickers bag.
Worker was struck by a tree.
Worker was struck by a delivery vehicle.
WA St Transportation Dept, Olumpia, WA 98501Worker was struck in the head b dead top of tree.
Village Pantry, Indianapolis, IN 46885Worker was working alone when two men entered the establishment. They came behind the counter and shot the worker and stole 21 cartons of cigarettes and no money.
Worker (14 years old) was pulled into a wood chipper.
Worker was operating a Vermeer ditch witch backfilling a hole. The stringer was struck by a passing vehicle and the ditch witch tipped over, landing on top of the worker."
Worker was walking back to his location and was struck by a forklift.
Worker collapsed walking into the office. Possible Heat Attack - Unknown.
Worker was working on the 2nd floor of a building and fell through an open door way to the ground.
Worker was changing the hydraulic fluid in a dump truck with the dump bed raised. The dump bed fell, pinning him."
Worker was struck by train while in company vehicle.
Worker was found underneath the desk and pronounced dead at the scene.
While taking tolls, a person drove up and shot the worker in the face."
Worker was found face down on site and taken to the hospital. Employer was informed that worker died on 9/7/2009.
Worker's vehicle was clipped by another vehicle causing the worker's vehicle to hit an on-coming big rig. The impact between the worker's vehicle and the big rig caused the fatality.
Worker working in a tree, fell hitting their head."
Worker got into an accident, got out of the car, walked onto the street, and was hit by another car."
Worker was adjusting the temperature leaning through a guardrail. He was struck by a roller cam, and his head was caught between the guardrail and roller cam."
Worker was on a platform by a sander. The platform gave way, and the worker fell to the concrete floor."
Worker suffered a stroke in his home on 11/21/2009. Worker responded to alarm earlier that same day. Worker died at the hospital on 11/27/2009.
Eastern Illinois University, Charleston, IL*",While riding home from a football game, the worker was killed in an automobile accident."
Worker fell in underground pit tank where there were recirculating pumps.
Worker was painting a boat on the water and was unaccounted for. Worker drowned, and the body was found underwater."
Worker gained access to the roof of the construction area. The worker fell from a significant height and died from those injuries. It is unclear whether the worker jumped or fell from the roof.
Worker fell from atop of a feed truck.
Worker was removing a radiator from a house, and fell 7 feet off an unguarded wood deck."
Worker was cutting down a tree using a chain saw. The tree fell onto another tree, causing a branch to fall on the worker."
Worker was preparing to remove waste containers from the highway and was struck by a motor vehicle.
Viking Electric, L.L.C., Phoenix, AZ* 85034Worker was changing the ballast on a light fixture and was electrocuted.
Worker was installing stage lights at a height of 25 feet from a truss system and fell.
Worker was standing on the medium and was struck by a car.
Valero Refinery, Texas City, TX 77590Worker was lighting a pilot on a boiler in a stream unit when the boiler catastrophically failed.
Worker was driving north in patrol vehicle when an attempt was made to pass another northbound vehicle. The vehicles made contact and the worker's vehicle went off the road and hit a utility pole.
Worker was performing duties when he reportedly felt ill and then collapsed from cardiac arrest.
Worker was found unresponsive with head injuries next to an overturned stepladder. The worker never regained consciousness.
Worker was found in employee locker room and was taken to emergency room. Worker was pronounced dead shortly after of a possible heart attack.
Worker suffered a heart attack and died while walking to meet a forklift driver to get supplies.
Worker was crushed when the equipment he was standing on slid off the trailer it was loaded on. The worker was crushed between the bag house and the remaining equipment on the ground.
Worker was on DNR property scouting for well sites for a municipal water system. Worker was riding an ATV, and it appears that the vehicle slipped on the steep terrain throwing the worker off and then landing on top of him."
Worker complained about not feeling well. The worker went home and collapsed about 3 hours later and died before taken to hospital.
Workers (2) were in a horse barn fire.
Exel Inc., Lancaster, PA 17061Worker was operating a picker and was pinned between the horizontal rack bar and the controls of the picker.
Workers (2) were engaged in debris removal. They were in the cab of a Caterpillar D-4 dozer and drove it toward the river. The dozer fell into the river, and the two workers drowned."
Worker was crushed by falling granite countertops.
Worker was found having chest pains and was taken to the hospital. Worker died at the hospital.
Worker was installing copper flashing on a roof and was found unresponsive on the ground between the bases of two ladders.
Worker was backed over on highway construction site.
Worker was fatally shot at a Perry County Clinic.
Worker was delivering medical products and was run over by his own truck.
Worker walked into cafeteria when he had a heart attack. CPR was initiated. Worker was taken to the hospital where he was declared dead.
Worker was in the attic of a center under construction and was electrocuted.
Worker was pinned between the bed of a dump truck and the cab/chassis.
Worker was walking from the parking lot to the entrance and was run over by a delivery truck.
Worker was shoveling corn into a bucket of a bobcat and was found unresponsive.
Worker was electrocuted after contracting an overhead high-voltage line with a portable light tower while working at a water main repair site.
Worker was found on floor unconscious, no witness. (Inspection planned)"
Worker was laying paper and plastic on finished floor and stepped into a hole, falling onto the concrete floor below."
Worker was performing highway snow plowing duties and was involved in a collision with a train at the crossing.
Worker was installing decorative lights on a 10-12 foot tree, touched an overhead electrical line and was electrocuted."
Worker was struck by a backhoe during land clearing operations.
Worker fell from a pump jack scaffold.
Worker was cleaning a dump truck. Worker stuck his arm into salting auger and was sucked in.
Worker was thawing two 3-inch valves with a propane torch on a tank trailer that exploded.
Worker was found in the receiving basket of a cotton stripper.
VN Printing, Houston, TX 77002",Worker was struck by a 1,500-lb load."
Worker was trimming a lower branch on a tree. An upper branch worked loose and fell on him, striking his head."
Worker was performing timber felling operations and was struck by a tree.
Worker was walking to the flea market's concession and was struck by a vehicle.
Worker was walking and working on the second level floor. Worker was moving equipment and fell 11 feet and was struck by an electrical panel that he was moving.
Worker fell into a 4-ft by 8-ft hole leading to a 20-ft depth reservoir and drowned.
Worker fell from a ladder while working inside an airplane.
Worker was securing tarp on a roof (not wearing fall protection, although it was available) and fell 35 feet to lower level."
Worker was on ground when he was run over by a front loader.
Worker, who is the owner, was doing electrical work and fell through the skylight. (No inspection planned)"
Worker was found in vehicle with engine running; carbon monoxide over exposure.
Worker was repairing a roof insulation and fell 14 feet to the ground.
Worker was found unconscious in her cubicle by a janitor. (Inspection planned)
Estes Express Lines, Seekonk, MA 02771Worker was crushed between the forklift he was operating and a concrete bollard next to the loading dock door after stepped off the forklift.
Worker was part of a four man tree trimming crew and was in the process of cutting down a 25-foot palm tree. Worker walked into the path of the falling tree and was struck by the tree.
Worker was installing shingles and moving planks on a roof and fell 20' 6"" from the roof to a driveway below."
Worker was cleaning up on side of the road and was run over by a dump truck backing up.
Worker entered a storage bin through a track side access hole that was 15 feet above ground and was engulfed by sunflower seeds.
Worker, a Quality Control Manager, was found lying face down. (Inspection planned)"
Worker was being elevated from a trash box on a forklift to reach a light pole. The trash box and worker fell to the parking lot.
Worker was working beneath an elevated hydraulic platform and the platform failed, crushing the worker."
Walls Contractors, Inc., Newport, AR 72112Worker was preparing drywall to be painted and found a coil of wire hanging from the ceiling. He attempted to throw the coil over a beam in the ceiling. The coil of wires struck the beam and fell back down. The wires contacted the worker and he was electrocuted.
Worker was operating a track hoe to remove columns lodged against a building. The columns were rigged with a nylon strap and were attached to the track hoe. While hoisting the façade from the building, the strap broke and the concrete façcade fell on the cab of the track hoe, fatally injuring the worker."
Worker on a derrick board fell with the collapsing mast. The derrick board broke loose from the mast and the worker was thrown against a metal structure on the ground.
Worker was contracted to remove and install a new breaker that controlled a chipper. The disconnect was placed in the off position and the worker began disconnecting the I/O cable from the lugs inside the box, when an arc flash occurred."
Worker, an Inspector, was walking in a crosswalk when he was hit by a city vehicle."
Worker was loading lumber onto a flatbed truck. Worker climbed the load to put spacers under forklift load. As he climbed, the lumber collapsed onto him, crushing him."
Worker, a maintenance employee, was removing steel beam for the installation of new assembly equipment. After one end of the beam was cut by a welder, the beam apparently slid off the forklift it was raised on and struck worker."
Worker was removing icicles from the roof line of a building. Worker was located in a box attached to a forklift, the box shifted, and the worker fell 30-feet to the concrete below."
Worker was caught in the unscrambler.
Worker was in a basket of an all-terrain forklift at 40 feet, when it tipped over."
Worker was shot by an armed robber.
Worker was killed when a rail car jumped its tracks and pinned him against a building.
Worker was driving a postal service truck on a town road and a tree fell, striking the truck."
Worker was at a trucking dock, unloading one truck and loading another. While parked at the dock, his truck caught fire; worker died in the fire."
Worker was unloading granite slabs from a truck, the weight shifted. The worker was crushed by a slab."
Worker was working on an I-beam 20-feet above ground when another I-beam above came loose and fell, crushing him between the two I-beams."
Worker in the process area was found under a freight elevator.
Worker was installing a box in a residential yard when he was struck by a vehicle that was operated by a drunk driver. (Inspection Planned)
Worker was backed over by a garbage truck.
Worker was climbing a ladder and fell backwards 6 to 7-feet to the ground, striking his head on the concrete floor."
Worker was run over by a roll-off trash truck.
Worker was working on the roof when he fell. He was taken to the hospital, where he passed away on 12/24/2009."
Worker was working with glass product when glass struck worker in the neck.
Worker was in a trench installing 8-inch pipes for a new sewer line. As another worker operated the excavator, he noticed the worker covered waist deep in dirt. After 20 minutes the worker was removed from the trench and transported to the hospital where he died."
Worker was crushed by a cable after being pulled into a motorized capstan.
Worker was crushed by the boom of a skid loader while performing maintenance.
Worker's death believed related to long-time exposure to chemicals used in painting operations. Worker used paint, mineral spirits, and xylene. Worker passed away at his residence. (Inspection planned)"
Worker was resting in a recliner in his trailer when he was struck by a drilling pipe stand that fell from a derrick.
Worker was cutting a 55-gallon steel drum with an acetylene torch to make it a burn barrel. The barrel was not vented, and the isopropyl alcohol at the bottom of the barrel exploded from the top, dousing the worker, and engulfing him in flames."
Worker was struck and crushed by a truck trailer that was backing up.
Worker was squatting down on the deck of a crane to install the bolts on an oil cooler and fell 6-feet to the concrete floor.
Worker, during the loading/unloading process of calcium fluoride, was found unresponsive on top of the tanker."
Worker was lowering the dump bed of a dump trailer, which was stuck in the raised position. Worker entered beneath the upraised bed to rock the ram into position to lower the bed. The ram dislodged, causing the bed to fall. The bed struck and crushed the upper body of the worker."
Worker working from a ladder, cutting a pipe, lost his balance and fell to the ground below hitting his head against the side wall."
Worker was working on the dump valve flange and 3"" line that led to a welded ""T"" of a high pressure separator when a fire/explosion occurred."
Worker was moving a drill and contacted an overhead powerline.
Edaleen Dairy LLC Lynden, WA 98264Worker was preparing for herd health and was shutting the east overhead door when the door came down suddenly pinning the worker between the top of the gate and the bottom of the door.
Worker armed himself with multiple weapons, fatally shooting three workers and self; wounding five other workers."
Worker, a maintenance worker, was attempting to move a refrigerator down some stairs when he lost his footing and fell backwards, striking his head on the concrete stairs before falling down. The refrigerator fell onto the lower portion of the deceased."
Worker fell from a two-story residence.
Worker had part of an end loader fall on him.
Worker was doing a retrofit when the excavated area began to fill with water. Worker was trying to locate the water service that was hit and was electrocuted on 2 large electrical conduits that had not been previously located.
Enbridge G & P (East Texas) LP Douglasville, TX 75560Worker was replacing a valve on a waste heat boiler when hydrogen sulfide was released to the atmosphere.
Worker operating an overhead crane with a pendant was moving sheets of steel. He positioned himself between the load and a metal barrier guard that ran along the aisle or stacks of sheet steel on the opposite side of the aisle. The load struck the other stacks of steel or a metal barrier guard, causing the load to spin, catching the worker between the load and either the stacks of steel or the metal barrier guard."
Worker was unloading pipes and was struck by two pipes that fell from the load.
Worker, a pizza delivery man, was shot fatally during a robbery."
Worker fell 80 feet in grain silo.
Worker was in the basement's mechanical rooms and suffered a heart attack.
Worker was using a toga crane hoist. Worker inhaled a chemical (ammonia) that was leaking by the cooling tower.
Worker was working on avalanche control and was buried in 6 feet of snow while setting charges to release the build up of snow to avoid an unplanned avalanche.
Worker climbed the roof of the furnace to shut off all water when an explosion happened. The worker fell 12 feet to the floor from the furnace roof. Four (4) other workers were injured.
Worker was performing clerical duties at the front office when she started feeling sick and vomited at her desk. She went to the restroom, she was incoherent and became unconscious. (Inspection Planned)"
Worker was chipping brush and was struck by an automobile.
Worker was crushed by a locomotive alternator frame that fell off an oven table.
Worker was working on a roof/deck and fell into an elevator shaft, 30-feet."
Worker was erecting a scaffold and fell 30-feet to the ground.
Workers were replacing a vent line on top of a tank battery. They were exposed to hydrogen sulfide gas. One worker fatality and three workers were hospitalized.
Worker was pulling telephone cable and tightening it up with a winch. He became entangled in the cable.
Worker was taking a dip tank sample by hand with a 8-ounce plastic bottle. The automatic hoisting mechanism struck, caught and crushed him between the frame of the hoist mechanism and the dip tank transfer bar."
Workers were on the production platform sleeping when a fire/explosion occurred. They evacuated the platform and were in the water for 1.5-2 hours before being rescued. One worker fatality and two workers were hospitalized.
Worker was erecting a steel structure and was struck by a steel I beam.
Worker fell off bucket 30-feet striking utility lines during his descent.
Worker was crushed between his trailer and another trailer that was backing up.
Worker, a teacher, fell down one flight of stairs from the stairwell landing while escorting students from classroom to lunchroom. Possible heart attack prior to fall. (Inspection planned)"
Worker was unloading household goods at a residential site when the loading ramp to the truck allegedly slipped causing the victim to fall and strike the side of the ramp resulting in internal injuries. The worker was admitted to the hospital where he underwent surgery for a lacerated spleen, kidney damage and punctured lung the following day. Prior to discharge from the hospital the worker sustained a massive heart attack."
Worker, a logger, died several hours after removal from frigid water."
Worker, a crane operator, suffered 3rd degree burns on his legs and back on 1/6/2010 and expired on 1/15/2010."
Worker tripped and fell during a visit to a patient's home.
Worker was working with a compost machine. His jacket was caught in the machine pulling him in the machine causing asphyxiation and death.
Worker, a store attendant, was working at convenience store/gasoline station and was shot fatally during robbery."
Worker was found deceased in a creek bed. Initial investigation suggests the victim fell 36 feet off a bridge.
Worker was crushed by a beverage cart that slid off a lift onto him.
Worker was crushed by a lift truck.
Worker fell from the deck of a tug boat transporting coal barges on the river. Worker was swept underneath the vessel by the river current and drowned.
Worker was operating a dump truck hauling rock that was being dumped into the lake. The dump truck fell through the ice near the dumping site killing the worker.
Worker was caught in a block line.
Worker had entered a soil hopper system while the auger was rotating. Worker's clothes were caught in the rotating auger, pulling the worker's body into the auger."
Worker was in the process of installing the connector pins to secure two trench boxes. A cave-in occurred, knocking the upper trench box off the lower trench box and pinning the worker between the spreader bars of two trench boxes."
Worker was testing an electrical panel at 480 Volts and was electrocuted.
Worker fell from a tower at a non-operational unit at a refinery complex.
Worker was working on a mezzanine to move an air handling unit using a pry bar. Worker lost his footing and fell from an unprotected edge to the floor 20 feet below.
Worker fell through a guardrail 8 to 10 feet from mezzanine to lower level.
Worker was installing 2 by 6 ceiling joists on a home. One of the joists broke; the worker lost his balance and fell 10 feet to the concrete floor inside.
Worker was removing the cone-shaped roof of a grain bin. Worker was working from a basket that was attached lengthwise off of the end of the forks 12 feet and was elevated 35 feet in the air. The forklift tipped over and struck the ground.
Worker was spray painting a building and was found pinned/crushed between the aerial bucket and an awning structure.
Ethyl Corporation, Pasadena, TX 77503Worker was collecting a water sample and was found with the upper half of his body in a diked containment area containing 11 inches of rain water.
Worker was standing beside his truck preparing to strap down a load of steel sprinkler pipe bundles, when a forklift operator loading bundles on the left side of the truck bed inadvertently knocked a bundle off the truck bed. The bundle struck the driver knocking him to the ground. He was transported to the hospital where he died later from internal injuries."
Worker was struck by passing vehicle while he was delivering cars.
Worker was run over by tractor trailer.
Worker fell from roof elevation.
Washington Metropolitan Area Transit Authority, Rockville, MD 20805",Two maintenance workers were killed when struck by a rail maintenance vehicle while establishing a work zone.
Worker was installing security cameras and fell from a flat roof 16 feet.
Worker was working at 2:47 a.m. in a convenience store, when he was shot during a robbery attempt. He was taken off life support on 1/27/2010."
Workers were coating the interior of a trailer tank; fumes ignited from the trailer tank, causing a flash fire. One worker fatality and two workers were hospitalized."
Worker was disassembling storage racks from inside a scissor lift elevated 20 feet and attaching a strap to the rack and slowly leaning it over. The strap caught the lift and tipped over with the rack.
Worker was standing on a ladder with a chain saw to cut a tree trunk. The chain saw apparently struck the victim 's neck.
Worker either fell from ladder or roof.
Worker of New York City Housing Authority was found dead at his work station in the boiler room. (Inspection planned)
Worker was unloading a trailer, and a box fell on him."
Worker was killed after being pinned between a tractor trailer and his garbage truck.
Worker was crushed between a delivery truck and the loading dock resulting in serious injuries and his death.
Worker was struck by a steel shaft being worked on in a lathe.
Worker was run over by a forklift on a construction site and fatally injured.
Worker was in the process of unloading a truck when the forklift he was operating overturned.
Worker was found at the log loading site beneath the front right tire of a skidder.
Worker was found lying dead on roadway adjacent to work. Apparent homicide.
Worker was inflating a tire that exploded, striking him"
Worker was assisting in the delivery of granite slabs using a forklift.  The forklift hit two slabs that fell, striking the worker on the head."
Worker was in the process of putting equipment on a machine and was found on the ground by other workers; apparent heart attack.
Worker was found unresponsive after pulling a tractor trailer into the shop building.
Worker was installing metal roofing and fell 35 feet, hitting the concrete floor."
Worker was lowered into a 30- to 35-foot deep shaft to perform hand cleaning and to drill a sample test of a rock.  He was being lifted out of the shaft by the use of a pneumatic winch system.  The winch system collapsed into the shaft, striking the worker."
Worker was adjusting the wheel location of a trailer and was run over by the trailer of the truck.
Worker fell from scaffold into a window opening and 20 feet down an elevator shaft.
Worker received severe steam burns to his lungs during the clinker material clearing process.
Worker was disassembling a communication tower and fell 98 feet to the ground.
Worker noticed the sodium hydroxide pipe was leaking. He tried to stop the leak and got sodium hydroxide on himself. After cleaning the spill, the worker took a shower and collapsed and died."
Worker was operating a tug vehicle that transfers luggage from terminals to airplanes. The tug collided with a food service truck. The worker was ejected from the tug and struck his head on the pavement. He was transferred to the hospital where he later died.
While working on a metal roof, the aluminum metal sheet, which was deteriorated, broke. The worker fell to the ground, later dying at the hospital."
Workers were painting a newly constructed sludge pit. Worker turned to find other worker slumped down by the wall.
Workers were doing a ""blow down"" to clear gas from the lines and an explosion occurred.  One worker fatality."
Workers were doing a ""blow down"" to clear gas from the lines and an explosion occurred.  One worker fatality."
Worker slipped at work, fracturing ankle.  Worker died of blood clots two days later."
Workers were doing a ""blow down"" to clear gas from the lines and an explosion occurred.  There were three fatalities."
Worker was caught between the back of a semi-trailer and a loading dock. He was transported to the hospital where he later died.
Worker was shot by an unknown assailant in the parking lot and was hospitalized; shooter then committed suicide.
Worker was struck by a dump truck.
Worker entered a manhole in an abandoned sewer line to remove a cap from a vent line and fell 7to 10 feet from a ladder.
Workers were working under the chassis of a water pump that was up on four jack stands.  One of the jacks was removed and the water pump came down, crushing the worker."
Worker was dipping a metal part into a heated bath and an explosion occurred, burning worker."
Excavator broke through ice coming to rest on its side and entrapping worker underwater.
Worker fell out of bucket truck after his truck was struck by another vehicle.
Worker suffered heart attack and died while sweeping water from the roof of an apartment building. (Inspection planned)
Worker was assaulted by a homeless veteran.
Worker was using a wood chipper to process branches from a tree trimming job.  The chipper discharge chute clogged up and the worker removed the pin that held the access panel down over the cutterwheel.  The cutterwheel was still rotating and discharged wood material against the access panel, which flipped open and the worker was hit in the face and forehead with the handle of the access panel."
Worker was emptying rock salt out of the back of his dump truck with a spreader.  His arm was caught in the rotating auger distribution system.
Worker was exposed to a chemical stripping agent and suffered respiratory pain / illness due to poor ventilation.
Worker was trying to grab a large piece of cardboard out of the back of the garbage truck when the driver began to close the tailgate. The driver heard the worker and opened it. The worker who had been caught by the tailgate was transported to the hospital where he later died.
Worker was working on a column and fell over safety rail from the second level.
Worker was crushed between the ground and the arm of an automotive lift.
Worker was working in the yard moving a piece of steel with an overhead crane.  The piece fell, crushing the worker."
Worker was attempting to tie into a main water line that was 17 to 20 feet underground when the trench collapsed.
Worker was working from a manlift connecting a beam.  The beam being held by a crane, shifted and hit the manlift knocking the worker from the manlift, 14 to16 feet to the ground."
Worker was refilling aboveground fuel oil tanks from a tank truck.  He had walked behind the truck and bent over, his coat was caught in the power take-off."
Worker, a machine operator, was using a grinding machine and the grinding wheel on the machine broke into pieces. One piece of the wheel struck the worker in the face. The worker died instantly."
Worker was draining a tank; one of the employees climbed to the top of the tank and lit a cigarette and waved it over the opening in the tank.  The tank exploded, killing the worker."
Worker found unconscious in a hog barn.
Worker was working in the kitchen area and fainted / fell to the floor, grabbing hold of a deep fryer, spilling hot grease out onto her and burning 30 percent of her body."
Worker was removing an antenna from a hangar roof.  He was walking a beam and stepped off and fell through the roof of the hangar.
Worker was struck by a powered industrial truck that was loading paper bales into a semi-trailer.
Worker was traveling underneath a coal transfer belt.  A large icicle broke away from the belt structure and fell onto the worker.
Worker was crushed by the bulldozer he was operating. He was transported to the hospital where he later died.
Worker was descending from the cab/platform built into the side of the vehicle. The worker fell backwards and landed on the concrete floor.
Worker was bitten by a customer's dog at a gated storage facility while on duty. Worker passed away two days later at the hospital from blood poisoning related to the dog bite.
Worker was moving hay out of a barn from a height of 10 to 12 feet. He fell and received head trauma, from which he died."
Worker was struck on the head by a tree limb while felling a tree.
Worker was performing maintenance on an extruder machine. He was discovered caught in the machine by the plant manager. He was pronounced dead at the scene.
Worker was murdered.
Worker was troubleshooting a Makino, multi-axis, computer numerical controlled (CNC) machine; the machine activated and the worker's head was impaled by the tooling spindle."
Worker was climbing a tower at a height of 58 feet and began having convulsions.
Worker was working as a landfill spotter. He was behind a CAT 836G compactor and the operator of the compactor did not see him. The operator of the compactor backed over the worker. He was taken to the hospital where he later died.
Worker was attempting to find the problem of a hydraulic flatbed truck.  He rose up the flatbed and positioned himself beneath the raised flatbed and the frame.  The hydraulics gave way and the worker was crushed.
Workers were utilizing excavator with pipe clamp to plastic-wrap 18-foot pipes. Upon completion of wrapping, the pipe excavator operator picked up pipe with the clamp. The pipe came out of the pipe clamp resulting in the pipe falling onto the worker's chest which caused a fatal crushing injury."
Worker was in the process of unloading pipe from a trailer.  He was removing a chain that was routed through the middle of the front weigh bridge, when the pipe rolled off the top of the load, striking the worker in the upper extremities knocking him down on the ground."
While operating a boom truck attempting to move a junked truck, suddenly the boom broke from its base and stuck the worker causing a serious chest injury. The worker was killed."
Worker, acting as a spotter, was struck by the garbage truck that was backing up."
Worker was working on a step ladder adjusting a pipe on top of the pasting machine and fell backwards off of the ladder, hitting his head on the metal plate floor."
Worker, an animal trainer, was attacked by a killer whale in an aquarium's exhibition tank."
Worker had exited the cab of a truck.  Worker ran across the street to collect garbage and was hit by a vehicle.
Worker of a structural steel erection crew that was installing roof decking fell from the deck under construction to the concrete floor below. Worker was transported to the hospital where he later died.
Worker was doing a job on a 6-foot ladder, lost his balance and fell, striking his head."
Wal-Mart Store, Rogerville, TN 37857Worker tripped on an extension cord and fell onto a tiled floor in the deli. She was transported to the hospital where she later died.
Worker caught by the garbage truck compactor.
Worker was returning from the rest room and collapsed.
Worker fell in a sewage pit.
Worker had climbed a ladder to watch his gang.  A rolling crane was approaching his location and he did not see the second crane coming.  The walkway of the crane struck him off the ladder onto the ship's main deck. He was then caught by a piece of pipe and dragged until the crane was stopped.
Worker was struck by a 500-gallon tank that fell off the tines of a forklift.
Worker pressure washing a freezer via gasoline-powered washer was overcome by carbon monoxide.
Eastman Drilling Co., Blackwell, OK  74631Worker was drilling a water well.  The boom of the drilling rig contacted a high voltage power line of a cell phone tower.  Worker was electrocuted.
Worker was in the process of removing synthetic straps from a load of four, 7-inch by 50-foot long, metal utility poles, when one of the poles, stacked on top, fell and landed on top of him."
Worker was flushing a refrigerator line and did not extinguish the pilot light on the water heater.
Wireline Control Services, Alice, TX  50518",Worker was working in a pressure wash bay, cleaning some open-ended pipe, and was found collapsed on the concrete floor."
Worker was driving a commercial truck and collided with several large bales of hay that fell off an unknown semi-trailer.
Worker was making preparations to stack steel beams in a storage area; an I-beam fell from a mansport truck, striking the worker."
Worker was using a ""Better Spreader"" to apply glue to the rubber membrane, walking backwards.  He backed off the roof and fell 27 feet to the ground below."
Worker was installing lamp/bulbs while in an elevated bucket on a truck and contacted a live wire, receiving a lethal shock."
Erickson Contract Surveying, Inc., Beach, ND  58621",Worker was conducting seismographic drilling operations. Worker was tipping pipe out of the hole; the pipe came loose, and fell on the worker."
Worker was working inside a trench without a protective system; the trench walls collapsed.
Worker was working on the electrical wiring for overhead fluorescent lights in the attic of a plant, and was electrocuted."
Worker had taken a flat bottom boat out for a ride to put 10 hours of usage on the new motor.  Worker fell from the moving boat and his body was found later, floating."
Worker was killed when he overturned his side dump truck and struck a parked water truck.
Worker was working beneath a trailer when the jack stand broke.
Valor Technologies, Inc., Mt. Prospect, IL  60058Worker was disposing waste parquet flooring and tile from a gondola plastic cart into a dumpster.  Worker collapsed into the dumpster; apparent heart attack.
Worker was standing on platform/plywood on forklift and fell into a 15-foot excavation which collapsed around him, burying him."
Etchegaray Farms, McFarland, CA 93250  Worker was struck by falling windmill blades when he went to start equipment.
Worker was hit in the forehead by the hook of a crane that was being used to install a utility pole. He was knocked unconscious and transported to the hospital where he later died.
Worker had climbed down a ladder into a railcar, which had been identified as a confined space, wearing an acid gas respirator with an organic vapor cartridge.  As he began to exit the railcar, climbing up the ladder, he collapsed and fell back into the railcar.  It is believed there was a nitrogen atmosphere in the railcar."
Worker was inspecting a roof on 2/23/2010 when he fell 23 feet. He later died from his injuries on 3/10/2010.
Worker was using a power take-off (PTO) pump to transfer gasoline from one underground storage tank to another. The output pipe of the pump broke, spraying fuel over the worker. The fuel later ignited and the worker was seriously burned. He died the next day."
Worker was repairing damage to a 4160-Volt power line. The worker grabbed the part of the line which was not de-energized and was electrocuted, instantly causing his death."
Worker was conducting roofing work, removing sky lights, and fell 50 feet to the lower level."
Worker was spraying fertilizer with a utility cart boom sprayer.  The cart overturned trapping the worker.
Walsh Construction, Gary, IN 46403Worker was working on highway with two other Walsh Construction workers and a subcontractor patching potholes. He was struck by a drunk driver speeding at up to 90 mph.
Worker was killed during a store robbery.
Worker attempted to break a grain bridge manually by entering the bin and fell into the grain.
Worker was working in a vault and was electrocuted.
Worker was in the process of transferring grain from one bin to another, and was found in a grain bin covered by a few feet of corn, 20 to 25 feet away from the door."
Worker was standing on a flatbed trailer while a crane operator was loading three coils of steel onto the truck. The coils fell off the truck striking the worker who had jumped off the truck to get out of the way.
Worker was unloading pipe from a flatbed trailer when he was knocked off the trailer by pipe that then fell onto him.
Worker was working on a large RV vehicle with the front suspended on a jack.  The jack collapsed, and the vehicle fell on the worker."
Worker was carrying an oxygen/acetylene hose.  Worker was walking uphill across a roadway and was struck by an end loader.
Worker was directing the driver of an 18-wheeler truck backwards into a Poly A Unit.  Worker ended up in a position where the 18-wheeler tires rolled over and crushed his head.
Worker was driving a golf cart, picking up debris along the roadway, and was struck by a vehicle."
Worker was working on the airbrakes of the cab of a tractor trailer.  The truck engine engaged and dragged the worker until the truck hit another building.  Worker was found pinned between the left front tire and engine.
Worker was accessing the area under a load and was crushed/struck-by the scrap vehicle.
Worker was working on the wheel and axle line, using an overhead bridge crane to lift a 5,100-lb locomotive wheel set.  Worker lifted the locomotive wheel set, causing it to swing in a pendulum motion, pinning his leg against another stationary locomotive wheel set."
Worker became entangled in the rear differential of a vehicle.
Worker fell about 7 feet while pouring a concrete column for a new bridge. He was taken to the hospital where he died during back surgery.
Worker fell 25 feet off a manlift.
Worker was cutting tree branches and cut himself with a chainsaw.
Worker was working on a client's boat, and an explosion occurred."
Worker was working under a pull-behind compressor/generator and it fell off the jack stands.
Worker received a severe electrical shock after an overhead crane derailed in the facility he was working in.
Worker fell off of an unguarded stair landing and struck his head on edge of stair tread 10 feet below.
Worker went into a stacker to clean dust off a photocell eye.  He did not use lockout/tagout, and after the dust was cleared away, the stacker activated."
Worker was trampled by a bull.
Worker was spray painting utility when he was struck by a vehicle. Worker later died on 3/19/2010.
Worker was fatally shot during a robbery and was pronounced dead at the scene.
Worker fell from an elevated water tower area.
Worker was working on a motor, contacted live wires and was electrocuted."
Worker was operating a boom on a water well truck, when boom came in contact with overhead power line, electrocuting the worker. "
Worker, at the end of fourth day on night shift, drove company car into back of parked trucks. He received multiple head injuries."
Worker was sitting on a conveyor and welding, when the conveyor system was energized causing the employee to be crushed. No locks were used to lockout the conveyor system."
Worker was driving a JackRunner chipper. He left the cab of the chipper and got caught in the auger of the JackRabbit bank-out car.
Worker was checking on office of a coworker. The worker opened the window and stepped out on the ledge where he slipped and fell to the parking lot below - approximately 20 - 25 feet.
Three volunteers setting up 40-foot portable antenna for radio communications during bicycle event. Top of antenna swayed 10 feet and touched high voltage line. One killed; one injured.
Worker was attempting to clear a jammed flat of milk product containers when the ram actuator started moving forward, pinning the worker between the actuator and positioning post, crushing the worker. "
Worker fell from 15-story building to 6th floor atrium.
Worker was installing a telephone cable while standing on a fiberglass ladder. He came in contact with a 4,000-Volt electrical line and fell 15 feet to the ground and died."
Worker complained about not feeling well. He went to the basement of the store where he was running a gasoline powered generator. He was found at the bottom of the stairs. It was reported that carbon monoxide levels in the basement measured greater than 900 parts per million.
During a rescue attempt at a fully engulfed residential fire, two firefighters were injured and taken to the hospital. One firefighter died from his injuries. "
Worker was performing work on filter galleries of a waste water treatment plant.  Worker appeared to have a heart attack and fell 9 feet to the bottom of the filtering bed, suffering head trauma."
Worker was on a twelve-foot ladder and tapped on a valve connection from a pump union.  The union struck and destroyed the ladder.  Worker fell and was impaled on debris.
Village of Washington Park, Washington Park, IL 62204","Mayor of the Village of Washington Park was driving through the village at 6 a.m., after leaving his second job. He stopped when someone asked for assistance and was shot twice by someone in a passing car. "
Worker was transporting roofing materials and fell from height.
Worker was performing air conditioning work on the roof a building when he fell 25 feet to the ground.
Worker was walking at a truck stop when he was struck and killed by a tractor trailer.
Worker was working on a water line in a trench at a depth of 9 feet.  The wrench he was using slipped off of the bolt and he fell backwards into a deeper trench at a depth of 14 feet and struck his right knee on a cast iron fitting.  Worker had a heart attack/blood clot.
Worker fell down the stairway.
Heavy equipment driver was in the process of stepping down backwards from a low-boy trailer when he fell and hit his head on the asphalt. He never regained consciousness and died 4 days later.
Worker was struck by a pickup truck.
Worker was mounting a crane on a truck.  The crane fell and hit the worker.
Worker was installing floor plates on a drilling rig.  The bridal line and equalizer fell to the derrick floor, crushing the worker."
Worker had exited his truck and walked in back of the skidder.  The skidder backed over the worker.
Worker was remodeling a residential home and fell through a second floor window opening onto a pump jack scaffold and then onto the ground.
Whataburger Restaurants, Houston, TX  77040Worker was inspecting the parking lot and was struck by a vehicle.
Worker was instructed to drive the excavator back to the laydown yard.  The excavator boom was elevated and struck a steel girder of an overpass.  This caused the excavator to move to the center lane where it was struck by a tractor trailer.  Worker was ejected from the excavator and was run over by the rear wheels of the tractor trailer.
Worker was sandblasting the bottom of a water tower and fell to the ground.
Worker was dislodging lumber from a piece of equipment and another piece of lumber entered the area, crushing the worker."
Worker was positioned on the roof of a building, painting the exterior, using a plastic pole that had an aluminum pole on the inside of the plastic paint stick with a metal roller that was connected to the pole.  The paint roller or pole contacted a high voltage 7,500 Volt energized electric power line.  Worker was electrocuted."
Worker fell from a three story roof onto a concrete walkway.
Worker was installing a roof and fell 20 feet through a skylight, landing on the ground."
Wallace Cotton, Centertown, KY 42328",Logger was attempting to dislodge a tree that did not fall after it was cut. He attempted to cut another tree to hit the lodged tree. The second tree fell on him. He had worked for the company for one week.
Worker was working on his own vehicle and was pinned by the forks of a forklift and the vehicle.
Worker was kicked by an elephant.
Worker working in a room with inert chemicals was found unconscious; apparent heart attack.
Worker walked on the un-barricade or uncovered cut section of a roof decking and fell.
Worker was on the roof cleaning out the gutters.  He moved the aluminum ladder to relocate to another part of the roof and contacted a power line.
While responding to an emergency call, worker struck the rear of a recycling truck that was stopped."
Vegas Tunnel Constructors, Boulder City, Clark County, NVWorker death originally considered as result of heart attack. An investigation is now being conducted after receiving information that other factors may have contributed to his death.
Worker was pulling frozen food boxes for customer orders while standing on a wooden pallet lifted up by a company forklift truck. The forklift operator lowered the forklift, with worker still on pallet, to approximately 10 feet above the concrete floor, and began backing up. Operator heard something fall and found the worker lying face down on the concrete floor. "
Worker who was pushed by one of the customers, fell and hit his head on the floor.  He was taken off life support on 4/15/2010."
Worker was found underneath skidder's rear tire, after skidder was pulled into deck."
Worker was backing a forklift out of a truck and the truck moved away from the dock.  The forklift and worker fell out the back of the truck onto the concrete pad.
Worker fell off the tractor and was run over by the disc.
Worker was attempting to unload slabs of granite from the bed of a truck when the slabs tipped over and fell on him, causing fatal head injuries. "
Worker fell off of an unprotected edge of a roof.
Worker was struck by a 50-pound weight ball.
Waste Management, Ft. Myers, FL  33913Worker was dumping trash into the back of a waste management vehicle and was struck by a motor vehicle.
Worker was operating the Coil to Coil Polishing Machine and was caught in the coil portion of the machine.
Worker was assigned to move a wooden crate with nine large insulators that weighed 2,800 lbs.  In the process of loading the crate onto the rear of the flatbed truck, the crate fell over, crushing the worker between the crate and the rear of the truck."
Worker was repairing a roof and fell through the skylight, 20 feet to the concrete floor."
Worker was cleaning a dump truck and was pinned between the dump body and truck frame.
Worker was caught between fork truck and another vehicle.
Worker was in a boom lift, taking pictures, and was electrocuted after coming in contact with power lines."
Worker was electrocuted.
Worker was under a load when the boom of the crane collapsed, dropping the load on the worker."
Worker was repairing swamp cooler units. He slipped from a ladder and struck his face on a fence post.
Worker was storing supplies, fell backward, and sustained a fatal head injury."
Worker was welding on a 55-gallon drum of what might have been methanol and a explosion/fire occurred.
Worker was backing a truck into an inclined loading dock.  He got out to check on the dock clearance and walked between the truck and the dock wall.  The truck rolled back on him.
Worker was thrown from the seat of the digger derrick truck as the boom detached from the truck.
Worker was cutting a limb from a tree, the tree fell and contacted an uninsulated 13.2 KV electric line.  Worker was electrocuted."
Worker was operating a forklift, pulling pallets from a bin.  He pulled a pallet and the pallet above fell and spilled product on the floor.  He got off the forklift, tripped and slid on the concrete floor, he was knocked out."
Worker fell unconscious while participating in a hazardous material response drill. He was wearing a respirator and protective clothing at the time. He died at the hospital.
Weyerhaeuser Company, Port Wentworth, GA  31407Worker was walking down the roadway to his car and was struck by a rough terrain Lull forklift.  Worker was dragged 30 feet under the Lull along the roadway.
Worker was struck by a loader.
Worker was riding on a freight elevator; placed his head over the elevator's gate before it stopped and was caught in a pinch point between the gate and the second floor.
Worker was transferring chemicals from tractor trailer to stand alone trailer.  He reached over a power take-off (PTO) shaft and his coat got caught on a screw.
Worker was in the process of replacing a line and collapsed.  Not sure of heart attack or electrocution.
Worker suffered shoulder strain while installing portable greenhouse. Over time, developed severe pain and was sent back to physician. He died on April 22 from an infection."
Worker was pouring cable lubricant from a 5-gallon bucket into a new conduit near the floor of an underground primary switch.  Worker lost his footing and contacted the energized portion of the switch.
Wal-Mart, Sylva, NC 28779",Worker climbed onto a rack. While attempting to access the ladder, missed it and fell to the concrete floor below."
Worker was struck by a 20-foot steel column that broke loose from its rigging while being moved by a crane from one location to another.
Worker was performing some welding of conduit pipe.   The worker was welding on a floor next to a fryer. The wheel of the fryer rolled into a drain, causing the fryer to tip.  Hot oil at 325 degrees was dumped on the worker."
Worker was standing on the back of a pickup, loading PVC pipe, lost his balance and fell from the truck, striking his head."
Worker was hit in the head by a broken valve and related piping after the high-pressurized water line blew.
Worker was loading a semi with the use of a drag conveyor in a corn storage building and was engulfed in grain.
Worker fell approximately 18 feet onto a slate porch while installing a slate roof on a residence.
Worker had cut the last band holding a bundle of pipe together and was crushed after the poly pipe shifted.
Worker was repairing a hose on a hydraulic dock plate and the dock plate fell on the worker.
Worker was to determine why a boom section of a concrete pumping truck would not retract.  A bolt on the holding valve was loosened and nearly removed, high pressure hydraulic fluid blew the valve and bolt from the cylinder, striking the worker who was sitting in the boom."
Worker installing electrical wiring in a false ceiling, fell from ladder."
Bridge painter, not wearing a life vest, fell 18 feet from the bridge to the water and was swept away."
Worker fell from ladder.
Worker was descending from a scaffold and fell seven stories.
Worker was shoveling coal and became overheated and died.
Worker was doing a roofing inspection and fell.
Worker was crushed in a trench collapse.
Worker was struck by a vehicle that was backing out of the garage stall.
Worker was standing between a loaded trailer and an unloaded trailer chassis.  He was crushed between the unloaded chassis and the loaded trailer after a truck collided with the unloaded chassis.
Worker was working on a communication tower that was 240 feet in height, slipped, and fell from the tower."
Worker was in the process of re-roofing and fell 13 feet.
Worker was making a drill stem connection and was struck on the head by the pipe after it was lifted from the mousehole.
Worker was leaning over a parapet wall to take measurement of windows and fell from roof.
Worker was installing a 12-foot roll-up door from a ladder and fell.
Worker was found lying in a pool of blood in the parking yard.
Worker was responding to a gas leak in a 2-inch gas main and was struck by debris from the house that exploded.
Worker was operating a bucket truck to raise a communications wire that was hanging too low.  A truck drove by and caught the cable, pulling the worker out of the bucket truck 20 feet to the ground."
Worker was removing produce from a truck.  He was entering a glass enclosed back porch and his hand went through the plate glass window.  A piece of glass came down and cut the main blood vessels in his arm.
Worker was making an electrical connection in a junction box, working from an 8-foot ladder, and fell striking his face on a concrete floor."
Worker was sent to check on an electrical panel and was found unconscious.
Worker was electrocuted by static electricity built up on a plastic film roll line.
Worker suffered fatal injuries after falling off a moving garbage truck.
Worker was underneath a semi-trailer working on the driveshaft when the trailer began rolling backwards toward the street.  Worker was caught and dragged along with the semi-tractor.
Worker was getting out of his tow truck and was struck by a motor vehicle.
Worker was on a roof performing an estimate for a re-roofing job and was stung by a wasp.
Worker was working from an elevated platform on the mast of a drilling rig and was struck by a rotating steel casing.
Worker was carrying a welding feeder case on the port side of a barge, lost his hold on the case.  In trying to keep the case from falling, grabbed the whipline, and was pulled between the rails."
Worker was buried under waste being pushed into a trailer by a bulldozer, and suffocated."
Worker was engaged in testing asphalt and was run over by the truck.
Worker was changing out a boom section and removed the wrong pin, causing the boom to open up from the bottom, striking him."
Worker was struck on the head by banding.
Worker was removing debris with a leaf blower and was struck by an automobile.
Worker fell from a pump jack scaffold after a section of the work platform collapsed.
Worker was operating a riding lawn mower on a sloped area of a retention pond.  Worker rolled the mower over into the pond and was trapped under the mower and water, drowning."
Worker was dismantling an oil rig and was crushed between  a forklift and a truck.
Worker was crushed between a forklift truck and a roll of paper.
Worker suffered fatal injuries after being pinned between a forklift and machine.
Worker, disconnected from his fall protection, stepped off or fell off the monkeyboard."
Worker was running alongside a forklift to jump on, slipped, fell, and was run over by the forklift."
Worker was laying sod and was later found unconscious.
Worker was installing a safe that fell off its cribbing, pinning the worker."
Worker was assisting with moving a metal conveyor containing metal shavings, which was being lifted by a jib crane.  The load shifted and the end of the conveyor struck the worker on the chest."
Worker was mowing a grassy hill along a creek and was later found pinned under the mower in the creek.
Worker was working at the bottom of a barge, cleaning it up.  He was at the top of a ladder with a broom in one hand, his other hand released from the ladder and he fell back, striking a concrete structure."
Worker fell from a ladder.
Worker died after developing chest pains while training.
Worker died from head injuries after falling down stairs, while moving a chest freezer."
Worker died after he began vomiting and shaking. He was moved to the shade and first aid was administered (presumed heat stress).
Worker died after falling 23 feet from an extension ladder.
Worker was cleaning out a deep fat fryer and spilled some hot grease, receiving a significant burn to his left leg."
Worker was working from a cherry picker and fell.
Worker died after being backed over by a truck while walking along the road.
Worker was painting a dredging vessel.  He was down in a hole, located inside the vessel, and an explosion occurred."
Worker was struck by 8-inch high density polyethylene (HDPE) water piping that burst.
Worker was on top of a generator house preparing for hook-up and was found unconscious.
Worker stepped in front of a Lull® telehandler and was run over.
Worker fell from a mezzanine, 11 feet above the lower level."
Worker was pinned between two vehicles as he tried to stop a car from rolling out of a car bay.
Worker died after being struck by a tree during a logging operation.  The tree was supposed to fall in the opposite direction.
Worker put a car on the car lift and raised the car 4 feet, to repair the left front tire, and the worker went under the car.  The front of the car started leaning toward the floor, then fell to the floor; the rear of the car then came off the lift, falling to the floor.  The worker was still under the car and was crushed."
Worker was crushed by an all-terrain vehicle (ATV) after it rolled over during a photo shoot.
Worker was inside a water tower ascending a ladder and fell.
Worker was riding a motorized bike up a trail and went off the edge of the trail, falling 1000 feet."
Worker was repairing a large overhead hanger door, and was later found caught in the folded door."
Worker was fitting and welding into place a center line frame on a barge.  The frame fell on the worker, crushing the worker."
Worker died after inhaling a selenium compound.
Worker servicing the hydraulic system on cultivator tractor, was crushed by the cultivator tractor tire."
Worker searching for missing person was killed when his all-terrain vehicle (ATV) struck a deer and rolled over.
Worker was refueling trucks used to refuel airplanes.  Worker was found dead on top of a truck with his head in the refueling hole.
Worker servicing an 800-pound temperature probe/agitator, used to mix contents in rail cars, died after being hit/crushed by the agitator.  Safety latch on a jib crane failed."
Worker was using a chainsaw to cut through a tree stump when the chainsaw got stuck in the stump.  A skid steer with a grapple attachment was used to push against the stump to free the chainsaw. The worker motioned for more pressure on the stump, and then he bent down and forward to look at the chainsaw.  The grapple cycle shot, striking the worker in the temple area."
Worker was stabbed by patron with a knife.
Worker was performing a heat change on a furnace and was running the product.  Worker was later found caught up in the rolls of the bridle.
Working was removing roof panels, became tangled with either an electrical cord or rope.  He disconnected his fall protection to untangle it, stepped back and fell through a section of the roof that had been removed, falling 23 to 25 feet to the concrete below."
Worker was working on an electrical system.  Unknown whether the worker sustained injuries from an electrical shock, natural causes, or a fall from a ladder."
Worker doing steel erection fell 60 feet from a structural steel beam.
Worker was probing a ditch for gas lines and was struck by a vehicle.
Worker was trimming branches from a tree using a metal painter's pole near a 2400 Volt electrical wire.  Worker was later found on the ground at the bottom of the ladder.  Worker was electrocuted.
Worker was installing new cell phone cables and antennas.  He was descending the tower and fell 240 feet.
Worker was operating a front end loader on a narrow mountain road and the loader rolled over.
Wada Farms Potatoes Inc., Pingree, ID 83262Worker fell 10 feet from a bin.
Worker was transferring liquid petroleum from a tank battery to his tanker truck, and an explosion/fire occurred."
Worker fell from the roof of a 55-story office building.
Worker was operating a forklift. She was caught/crushed between the forklift and a stack of palletized Gaylord boxes containing plastic pellets.
Worker was delivering a semi-trailer load of pallets to a warehouse and was run over by his truck.
Worker was cutting a felled tree. The tree fell into a larger adjacent tree, striking the worker."
Worker was assisting in cleaning the clean-up room, and was having trouble breathing. Worker had an asthma attack."
Worker died from heart failure, several days after suffering 3 broken ribs from falling on the floor on the way to the restroom."
Worker collapsed in men's bathroom due to a massive stroke.
Worker was not wearing a harness, 20 feet in the air, cutting a tree limb, the limb broke, swung around and knocked the worker from the ladder he was working from."
Worker was standing on the ground, tarping his truck with a roll of overtarping, and fell backwards striking his head on the pavement."
Worker was topping a tree while a second worker was felling another tree. The tree being felled, twisted and struck the first worker topping a tree."
Worker died after falling 30 feet from a floor opening on a mobile scaffold while performing maintenance on an aircraft.
Windsor Door Sales, Inc., Albuquerque NM 87114",Worker repairing an overhead garage door, fell from the ladder and struck his head."
Worker rigging-up; fell 90 feet to the derrick floor.
Worker was operating a propane cook stove and was severely burned after the propane gas system ignited causing a fire and/or explosion.
Worker was working on a chisel plow. He became trapped between the tire and the plow.
Worker was putting labels on boxes and was crushed by falling pallets.
Worker died after falling from a 5-story ramp.
Worker was removing a sign from the front of her truck and was struck by another truck.
Express Energy Services, Azle, TX 76020",Worker was trying to stab a pipe into the bottom of an elevator. The bottom bale of the elevator struck the pipe and swung into the worker, striking the worker on the face/head."
Worker was caught and crushed between rails of a roll container truck.
Worker was engaged in the setting of a structural steel beam, either fell on top or was struck by the beam as it fell from the top of a concrete basement wall."
Worker was cleaning planes and was exposed to chemicals.
Viper Construction, Wayne, PA 19087",Worker was climbing down a ladder with tools in his hand and slipped through the ladder, fell backwards, striking his head."
Watson Tree Service, Henderson, TX 75654Worker was trimming a tree and received an electrical shock.
Worker died after being struck and run over by an unknown motor vehicle that kept going; worker was thrown into the center lane and run over a second time by a tractor trailer.
Worker died after tractor trailer he was driving ran off the road and turned over.
Worker was performing drilling operations with an auger-type drilling machine to install and set utility poles into the ground. During the drilling process, a high pressure liquefied natural gas pipeline was struck and ruptured. One fatality and six wor"
Worker was performing repairs under water.
Worker was reglazing a bathtub and was found dead.
Worker was power washing a three-story house and was moving a ladder, lost his hold, the ladder went back hitting a primary conductive power line. Worker was electrocuted."
Worker contacted a power transmission line.
Worker was operating an automated laser cutter and became caught in a pinch point after the structure that holds the laser cutter moved to the right front area near the metal structure of the machine.
Worker was in the process of filling fuel into a tractor trailer and was struck by another tractor trailer.
Worker was working from a mango tree; his pruner struck an overhead powerline and he was electrocuted.
Worker died after falling unconscious while moving a pry bar during welding activities.
Workers were excavating caliche for an oil field location pad. The bulldozer nicked an unidentified pipeline, resulting in an explosion. Two worker fatalities and one worker was hospitalized."
Worker had delivered a load of steel tubing on a flat bed trailer and was struck by a bundle of steel tubing that was being off-loaded.
Worker was crushed between a tractor trailer and a loading dock.
Workers were moving a weighted sign to the entrance of a rig site with a forklift; questionable lightning strike. One worker fatality and one worker hospitalization.
Worker was struck from a falling load after the load fell off a forklift.
Worker was performing site survey work and was backed over by a dozer/grader.
Worker was crushed by a paper hopper that was being loaded by a forklift.
Worker sustained head injuries after falling from an 8-foot ladder in store; died 9 days later.
Worker, framing a second-level addition on a home, died after falling about 10 feet."
Worker was conducting HVAC repairs and was working from a 6-foot ladder on the HVAC system above the ceiling tiles. He was found on the floor in an unresponsive state.
Worker on tractor pulling a loaded manure spreader was run over and pinned by the spreader when tractor and spreader became disengaged and rolled backwards.
Worker hanging sheetrock fell from ladder and struck head.
Worker was placing a ladder to access a roof. The ladder contacted a power line and the worker was electrocuted.
Worker installing a gas line in the attic of a house collapsed from the heat.
Worker was fabricating oil absorbent booms filled with raw cotton fibers that float on water to absorb and limit the spread of spilled oil. Worker was operating a pallet-wrapping machine, as well as placing finished oil absorbent booms on the pallets. W"
Worker was electrocuted while working on a high voltage panel; was entrapped on the panel for one hour.
Worker was freeing a pump component under pressure and was impaled by the pump component.
Worker was loading a semi-flat bed trailer with 41-foot metal pipes with a weight of 5,000 pounds, and was struck by a pipe that rolled off of the truck."
Worker was loading pipe onto a flatbed trailer with a forklift. Worker was struck by a pipe and knocked off of the trailer bed.
Worker was found unresponsive in a trash dumpster.
Worker was on a loft/balcony area and fell from the elevated area.
Worker greasing gears in airport gate at night put head into gear door and was struck by door.
Worker was tearing down a transmission structure using a digger-derrick when a pole broke and struck him on the head.
Worker was replacing structural roof panels and fell through the roof.
Worker was retrieving a load of furniture from shelving with a stock picker. He was driving the stock picker backwards, the load snagged on the shelving and fell on top of the worker pinning him to the controls."
Worker was engaged in cutting an 8,000-lb boiler in sections with a cutting torch. The section being cut, fell off allowing the remaining section, 5000 lbs., to flip over onto its bottom and land on the worker."
Worker drowned after being pinned under a large grader that fell into a ditch/pond.
Worker was working under a truck fixing the brakes when the truck rolled onto the worker.
Worker was shot and killed by an off-duty corrections officer while outside hospital entrance on a break.
Worker inspecting a passenger train at night was found unconscious at end of shift.
Worker was in a grain bin breaking loose bridged grain that was not flowing and was buried in the corn.
Worker was working at an unstacker, went under a catwalk, and failed to lockout the equipment. Worker raised her arm up toward the roller and was caught and pulled into the roller."
Worker was running a lateral sewer line when the trench wall collapsed.
Worker cleaning up a trainwreck died when crane brake failed and crane fell and crushed him .
Worker was working with a truck boom. The boom struck a power line and the worker was electrocuted.
Worker was standing on top of a trailer load of pipes pulling the tarp up to cover the load. He fell over 10 feet from the top of the load, striking his head on the concrete floor."
Worker was found inside the plant on the side of a ditch with a four-wheeler on top of him.
Worker was cleaning out the bottom of yachts and was found floating near the pier.
Worker elevated in an aerial boom lift was killed when lift made contact with 115 KV transmission line.
Worker suffered mass trauma to his body; cause was not known.
Virgin Islands Paving, St. Thomas, VI 00801Worker was struck by a car.
Worker suffered critical head injury after falling from a scaffold.
Worker died from an oxygen-deficient atmosphere.
Worker was removing a frozen bolt from the track of a catepiller front end loader and was struck by a bolt that entered his forehead.
Worker died from an explosion.
Worker was doing a cable connection, working on a ladder 20 feet up, became unresponsive and fell to the asphalt."
Worker was repairing tires on a front-end loader. Worker crawled under the loader with a bead bar to attempt to break the tire bead from the wheel rim. The equipment shifted and came off the jacks, crushing the worker under the rear of the loader."
Worker was riding in a golf cart after a housekeeping assignment, collapsed and fell out of a moving golf cart, striking her head on the concrete cart trail."
Worker on the ground was struck by the boom of a tree delimber.
Worker was repairing an overhead door motor. He had removed the cover of the motor exposing the electrical components to replace a component. Worker leaned over the motor after replacing the component to make an adjustment to the chain, and began to shak"
Worker was cutting limbs from a tree and fell 50 feet.
Worker was working on a TV dish from a roof, lost his balance, and fell 9 stories to the ground."
Worker was installing an air conditioning unit. He was using a torch to sweat a pipe joint and was electrocuted.
Worker was struck by a load of wall panels that fell off his truck.
Worker was on a scaffold and the scaffold tipped over. Worker fell off and hit his head.
Worker was found crushed in the paper baler.
Worker was loading pipe onto a truck and was struck by pipe.
Worker was fatally struck in the head by the kelly bushing, which broke free during rig-up procedures."
Worker putting decking on roof joists was blown off roof by wind. He fell 17 feet and hit his head on a rock.
Worker fell 14 feet to the ground from the roof decking on a 10/12 pitch residential roof.
Worker died after falling to the ground when hydraulic ram elevating a telescoping ladder truck broke in half.
Worker fell out of a man lift.
Worker was in the process of finishing a roofing contract and fell from the roof.
Worker was setting up a camera and fell 20 feet.
Worker was cleaning out gutters and fell from a ladder.
Worker was felling a tree and was struck by another tree.
Worker was performing maintenance on a forklift truck battery charger and contacted live electrical parts of the battery charger.
Worker was crushed by a roller that tipped over.
Worker died when his head was impaled by metal from the drive section of a Ferris wheel. The employee slipped after acknowledging he was clear and the wheel began to turn, trapping his head."
Worker was working on the elevator bin deck area and fell into grain bin.
Worker was electrocuted after contacting a sagging 4000-volt power line.
Worker got off tractor, which then began to move. Then he tried to get back on to stop tractor, slipped, and was run over by tractor and trailer."
Worker was run over by a reversing loader which was moving dirt around a ""pork chop"" near an interstate entrance."
Worker was waving a truck to cross a railroad track and struck by the train rolling the truck over, pinning the worker under the truck."
Worker apparently fell while stepping out of a cherry picker and onto a scaffold.
Worker was removing a jam from the back of the machine and fell onto the conveyor in the paper pulper. Worker drowned or was scalded.
Worker was working from a scissor lift removing a glass wagon and was struck by/crushed by an overhead gantry crane.
Worker was working on a transformer came in contact with an energized 37 kV cable inside a transformer.
Worker was found unresponsive.
Worker was operating a Bobcat machine while installing a culvert drain pipe. The worker was thrown from the seat when the machine slid off an embankment, and was killed when the machine rolled over him."
Worker was assisting with the setting of tilt-up precast wall panels and was struck in the head by a falling pipe brace.
Worker was on top of a tree and was repelling down to make his cut, and hit the ground."
Worker was diving for black coral and drowned.
Worker was going to her car after work when she was struck by the vehicle of another worker pulling their truck out to leave.
Worker had installed a new tool and was making a dry run. The tool flew out of the machine and struck the worker on the head.
Worker was working construction installing a swimming pool. Worker died from a heat stroke.
Worker was struck by flying metal debris.
Worker fell from ladder while installing trim on the side of a warehouse (metal building).
Worker was renovating a piece of farm equipment. A piece of the equipment fell and crushed him.
Worker doing laundry work and became dizzy.
Worker was attaching sheet metal screws on a pre-fabricated metal building and fell from a scissor lift or a forklift platform.
Worker was working on an oil and gas tank; the tank exploded.
Work collapsed in the field from heat exhaustion.
Worker was performing electrical wire replacement, placed electrical wire in mouth, then grabbed a metal scaffold. Worker was electrocuted."
Worker was inside a 212-foot diameter tank cleaning out sludge when the air line to the respirator popped off; worker collapsed.
Worker was working in a temporary transformer and was electrocuted.
Worker was struck on the head by a falling tree.
Worker was found unresponsive in the lab.
Worker was at the top of a four-tank group to gather readings and was found collapsed in the walkway.
Worker was working in a roof truss for a winery. The roof truss collapsed and the worker fell.
Worker was disassembling/disconnecting a vertical turning lathe and was struck by the 1200-pound head ram of the lathe.
Worker was performing lawn care services and was struck by an oncoming car.
Worker was working on the roof of a greenhouse repairing a hole. Worker slipped and began to slide six feet down the roof until falling through the hole, landing on feet, then falling back, striking the ground with head."
Worker discovered by co-workers after falling from ladder. Died enroute to hospital.
Working was using a lawn mower, it flipped over pinning him beneath the water, and worker drowned."
Worker was helping to hook up a trailer, when he was crushed by a truck backing into a dock."
Worker was setting anchor bolts into a 4-foot concrete-formed wall, collapsed, and fell backwards. Worker suffered from heat exposure."
Worker was run over by a flatbed truck.
Worker was found on the floor with a mask on, connected to two hoses, one for air and the other for nitrogen."
Worker was working on an energized electrical cabinet and was electrocuted.
Worker was engaged in welding activities on an overhead air pollution control unit and was struck by a small piece of welding equipment/tool that fell from overhead.
Worker was on a scissor lift, stripping electrical wires, and was noticed lying on the floor of the bucket of the scissor lift. Worker was electrocuted."
Worker fell from a pallet that was elevated eight feet above the ground by a forklift.
Worker's left arm was amputated while working near a conveyor. Emergency assistance was called but the employee was pronounced dead at the scene.
Worker was in the process of rigging up the cable that was holding up the rig. The cart and the top drive track fell. The cart struck the worker.
Worker was changing a flat tire on a business trailer. Worker was jacking up the trailer and the trailer fell onto the worker.
Worker was in the process of moving between cattle pastures. Worker got out of the truck to open the gate and was struck by the truck.
Worker was working on the roadway, milling a joint in front of a bridge, and was struck by a vehicle."
Worker was doing electrical work on an overhead crane and was standing on the bridge of the crane by the control motors. Worker either had an electrical shock or a heart attack.
Worker was performing weed abatement using an all-terrain vehicle and was found on his back with the vehicle across his chest.
Worker was working on the ground, contacted an energized wrecking ball, and was electrocuted."
Worker stepped out of driver's door of dump truck and was struck by another dump truck that was backing up within the lane closure.
Worker was installing a new wire for a 72 kV transmission line and was electrocuted.
Westerchil Construction, Alexandria, LA 71301",Worker was cleaning up the jobsite by picking up lumber and other debris. He was seen lying on the ground unconscious, possible heat stroke."
Worker was cleaning the inside of a rail car that previously had gas inside. A flash fire occurred and worker was burned.
Worker was preparing and pouring a concrete patio. Worker began to show signs of heat exhaustion/heat stress, lost consciousness."
Whitestar Development Corporation, Niagara Falls, NY 14303Worker fell into a compactor and was crushed.
Worker was run over by a dump truck while working as a laborer on a road construction project.
Worker was removing stakes and strings from the fields, and collapsed."
Worker was standing on a ladder performing tree trimming and fell from the ladder.
Worker was transferring sand from a rail car into a truck using a conveyor belt loading machine. Fell onto the rotating conveyor belt and was caught inside the machine.
Worker fell off the back of a golf cart, hitting his head."
Worker was adjusting an hydraulic front-end bucket with a clamping device on a truck, when he was crushed between the bucket and clamping arm."
Worker was crushed between the boom of the backhoe and the stabilizer (outrigger) leg.
Worker shooting squirrels was killed when hit by a falling limb.
Worker riding in the back of a pickup truck fell out of the truck and hit his head when the truck hit a bump.
Worker was loading a truck and passed out.
Worker was servicing a utility pole to restore service to clients, came in contact with the energized part of an electric transmission line and was electrocuted."
Worker fell into a blocklayers mortar mixer and was killed by revolving paddles.
Worker was climbing down from a scaffold to get water and fell from the scaffold.
Worker was working under a forklift. The front being supported by two jackstands. He was removing a hydraulic cylinder, it fell on his hand. The jackstands became dislodged and the forklift fell on the worker, crushing his head and chest."
Worker was working to install a fiberoptic line and became unconcious, possible heat stress."
Worker was standing by a flatbed trailer during loading operations and material rolled from the trailer, striking the worker."
Worker trapped in trench up to his waist, was struck in the head."
Worker suffered an electric shock while operating a resistance welder. Hospitalized after injury, and died five days later."
Worker was struck in the head when a pipe rack on an oil drilling rig failed/collapsed. At the time of the failure the employee was positioned under a portion of one of the support members for the pipe racks.
Worker was in bucket truck performing tree trimming services and fell 15 feet, hitting his head."
Worker became stuck in top opening of a 37-inch deep mixing tank. Was found unresponsive with head and torso in the tank.
Worker drove off an embankment while driving a loaded log truck.
Worker was found crushed in a digester tube at a compost facility. Worker had previously been reported missing, and was found after a three-day search."
Worker was crushed when caught between an automatic laundry hopper on a shuttle conveyor and an industrial washing machine.
Worker doing cable installation fell off ladder to the ground.
Worker was using a powered vehicle conducting a routine security inspection. The vehicle rolled over, pinning the worker."
Worker electrocuted while working on a residential air conditioning unit.
Worker was feeding paper to a paper reel winder, his hand got caught and he was pulled through, receiving crushing injuries."
Worker was replacing a tire on a skid steer loader when he was crushed between the bucket assembly and the main frame of the loader.
Worker, sanding the ceiling of a breezeway, fell approximately 30 feet from a third floor landing to the floor below. There were no guardrails in place, and the employee was not wearing fall protection at the time of the accident."
Worker was using a forklift to move a small dumpster to a larger dumpster. He got off the lift to adjust the dumpster and did not lower the lift or turn it off. The lift moved forward and crushed him.
Worker was taking samples at a new road construction job-site and was struck by a dump truck or asphalt truck.
Worker was struck in the head by a metal pulley being used to drag fallen trees, when the nylon strap to which it was connected broke."
Worker was retrieving golf balls and drowned.
Worker was engulfed in corn.
Worker was performing paving work activities outside the established work zone and was struck by a passenger motor vehicle.
Worker was ascending to the roof and fell from the ladder.
Worker struck in the head after a dead tree being cut down, fell on top of another tree, which fell on the worker."
Worker was buried in 11 feet of soil after a trench collapsed during the connection of piping for installation of a trench drain.
Worker was performing electrical testing and sustained injuries.
Worker was collecting TTC signs and was struck by a tractor trailer.
Worker was operating an extended boom forklift to set roof trusses. He was driving on a sloped surface when the truss he was carrying dug into the ground. Worker raised the boom to get the truss out of the ground and the forklift became unstable.
Worker was constructing a bridge and fell.
Worker was performing tree removal services and was standing on top of his bucket truck waiting to winch some logs.  Worker fell off the truck to the ground between some logs.
Worker suffered brain injury after tripping over phone cord that got wrapped around his leg during a phone call and falling on right side.
Worker was delivering liquid propane to a residence when he was struck by a 500-gallon aboveground tank that dislodged and rolled on top of the worker.
Worker was in a roll-on roll-off (RO/RO) operation and was struck by an intermodal container.
Worker was electrocuted after making contact with a truck that had a fallen powerline on it.
Worker electrocuted after making contact with power lines while trimming trees.
Worker was unloading a metal crate from a truck inside a loading dock when metal crate door unexpectantly opened.  Suffered fatal crushing injuries.
Worker was performing steel erection and fell.
Worker was constructing curb and gutter work in preparation for a concrete pour.  Worker was found later, collapsed; hyperthermia was listed as cause of death."
Worker fell 35 feet from a tree.
Workplace violence; shots were fired, nine workers were killed."
Worker was working in an excavation and the trench wall caved in on the worker.
Worker was in an aerial lift and made contact with an electrical wire.
Worker was piling up tree limbs and said he wasn't feeling well.  He sat under a tree and slumped over, possible heat stroke/medical condition."
Worker was working on a double-wide mobile home.  The jack failed and the mobile home shifted, crushing the worker."
Worker was struck by a interior block wall.
Worker was crushed by a concrete form.
Worker was working in a trench and the trench collapsed, burying the worker."
Worker was complaining of being hot and was later found unresponsive.
Worker was electrocuted after making contact with a 7200 volt electric line while installing fiberoptic cable.
Worker was operating a boring auger machine that was located at the bottom of a trench and was struck by the boring auger machine.
Worker was riding an all-terrain vehicle (ATV), and taking soil samples.  The ATV crested the top of a ditch, struck a boulder and overturned.  ATV landed on top of the worker."
Worker was troubleshooting a humidity problem and fell from a ladder.
Worker was reconnecting a trailer section that had come loose and was struck by another semi truck.
Worker collapsed after exiting a manhole.
Worker was using a broom handle to push ground wire into the live wire and caused an arch electrocution.
Worker run over by a dump truck while working as a laborer on a road construction project.
Worker was working from a bucket in the process of removing a utility pole.  An auger was being used to widen the hole and remove the dirt. The auger hit a gas line and exploded, burning the worker."
Worker was unloading a skid, lost control, fell and hit his head on the ground."
Worker fell and hit his head while trying to climb over a partition wall to gain entry into a locked adjoining office.
Worker (Police Chief) involved in a motor vehicle accident with civilian driver.
Worker was traveling in a boat and struck an intracoastal channel marker.  He was ejected from the boat and struck the pylon head first.
Worker was repairing a 7200-volt, two-strand, electric distribution line and was electrocuted."
Worker fell through roof of his business while attempting to fix an air conditioner.
Worker was working on a roof of a fire-damaged building.  He was on a ladder and slipped, falling from the upper roof to a lower roof, then to the asphalt 20 feet below."
Worker was operating a forklift when he hit a curb, becoming pinned under overturned forklift."
Worker killed in vehicle accident en route to Mammoth, CA."
Worker fell from an iron rung ladder at the top of a 4-story building while carrying equipment up the ladder.
Worker contacted a power line and was electrocuted.
Worker was unloading mattresses and box springs and was stung by a bee.
Worker was struck by the counterweight and revolving superstructure of an excavator when he walked between the excavator and a hillside.
Worker was underneath an attenuator truck releasing the cushing bed.  He released the bed and it fell on him, crushing him."
Worker was removing a roof that was under renovation and fell through a section of galvanized sheet metal, 35 feet to the concrete floor."
Worker (police officer) died of injuries suffered after losing control of a police car which overturned during a chase, ejecting the officer."
Worker was working 10 feet below street level, cleaning dirt from a newly installed culvert, when the worker fainted."
Worker sustained fatal injuries after company truck, which worker was driving, was struck by an oncoming train."
Worker was found slumped over against building.
Worker was test-driving a cycle for a customer when he received fatal injuries from a traffic accident.
Worker was sandblasting a metal plate.  The plate fell over and crushed him.
Worker fell 160 feet from water tower.
Worker was performing roofing activities and fell 40 feet to the concrete surface below.
Worker was working on a machine which was supported on the forks of a fork truck.  The machine shifted and fell off the fixture which was supporting the machine on the forks.  The machine fell on the worker.
Worker was electrocuted while working underneath a residential home performing plumbing work.
Worker was cleaning the tank of a diesel truck and was on top the tank car replacing a cap and fell from a height of more than 10 feet.
Worker collapsed with seizures.
Worker was refurbishing a house and fell from a porch, down four steps onto cement."
Worker was electrocuted while installing a drop pole in an office cubicle in a state office building. Worker was wiring the whip for the power pole when the pole was energized.
Worker was seriously burned after becoming doused in solvent while operating a forklift near a solvent line. Employee left forklift to cut off solvent supply. Solvent ignited while en route to safety shower.
Worker was performing exterior painting and fell 20 feet out of a manlift.
Worker was working from a manlift.  He was working below power lines and raised the bucket of the aerial lift into the power lines where his forehead contacted the power lines.
Worker was felling a tree manually using a chain saw and was struck on the head by a limb from the tree.
Worker was caught between rotating drum and loading hopper of a ready-mix truck.
Worker fell from catwalk or scaffold.
Worker was found unconscious; probable heat stroke.
Worker was run over by a co-worker at a job site.
Worker was standing behind his semi-tractor rig and attached chassis and was pinned against the chassis attached to his truck by another rig and chassis.
Worker was lying down near a location where a job meeting was to be held; worker was non-responsive.  Suspected heart attack.
Worker was performing solder work to repair a hot water heater leak and dropped burning solder onto the floor causing an explosion to occur.  Worker ran out of the house with severe burns.
Worker was elevated 25 feet in the air on a high-lift rider truck.  The truck was knocked over by a second fork truck and the worker struck his head on concrete.
Reported as an electrocution; however, there is dispute about whether or not worker was electrocuted or became entangled in cord that fell in pool."
Worker was working underneath a vehicle.  The vehicle fell off the jack stands that were supporting it, crushing the worker."
Worker was found pinned under the mast of an overturned 3-wheel powered industrial truck.
Worker struck in head from material falling from crane while fabricating tank in bender.
Worker fell from catwalk while removing a hopper on a silo.
Worker was eating lunch and swallowed a bee.
Worker was operating a baggage tug and was ejected.
Worker was inflating a mounted semi-trailer tire and was struck on the crown of the head by the exploding tire.
Worker sustained fatal injuries after becoming pinned under a tree.
Worker electrocuted after making contact with live wire while moving lives from an old pole to a new one.
Worker was attacked by a bear that he was feeding/training.
Worker was working on a security light and fell from a ladder.
Worker was setting up a truck to auger a hole for a power pole.  While raising the drill, boom made contact with 17 KV overhead power line."
Worker was performing salvage operations of an oil field tank battery following an explosion from a lightning strike.  During the salvage operations, there was hissing noise followed by an explosion, fatally injuring the worker."
Worker sustained fatal injuries after being struck in the head as a 4-wheel crane, which worker was in the back of, fell over while erecting a cell tower."
Worker was unloading products from a truck.  While working from the top of the truck, fell and cracked head open."
Worker was struck on the head by a pipe that was being moved.
Worker was struck by a forklift and hit into a compressor.
Worker was connecting a 36-foot steel beam to imbeds on a poured concrete wall.  The beam was being held by two clips.  The worker was sitting on top of the wall, the clips failed and the beam fell pullling the worker off the wall."
Worker was engaged in road work and was struck by a vehicle.
Worker climbed over a guardrail and fell through a floor hole.
Worker was cutting down wind damaged trees and a  60-foot tall tree fell on him.
Worker was moving a large metal shelving unit and drove one wheel of the powered industrial truck off the edge of the dock platform.  Worker attempted to jump clear as the truck began to fall and struck and pinned to the concrete surface by the protective cage of the truck.
Worker crushed to death by a load of copper tubing after losing his balance when load came off the hook as it was being loaded on a flat bed semi.
Worker was part of a litter crew that was working along a roadway and was struck by a car.
Worker was applying acrylic roof coating on a building roof and the section of the roof gave way due to corrosion.  Worker fell through the roof and landed on a concrete surface 30 feet below.
Worker sustained fatal injuries after being hit by a log that became unsecured.
Worker was working in an aerial lift on a boom truck.  The boom snapped in half and the worker fell with the boom.
Worker crushed to death after getting pinned in a roll-up door that was closing.
Worker was laying concrete and collapsed.
Worker was re-locating sprinkler heads, working from a 10-foot step ladder, and fell four to six feet to the ground."
Worker was using a stand up forklift to pull an order of frozen chicken from a 5 tier rack with 3 pallets per location.  Worker was found on the floor covered with bags and cases of frozen chicken.
Worker was unclogging auger openings in a grain bin.  The grain that was caked on the walls fell on the worker, engulfing him."
Worker was caught between a waste collection truck and a trash bin.
Worker was riding a pallet on the forks of an industrial truck when his foot was caught between the pallet and stationary object.  Worker died of a reported embolism at a medical facility.
Worker was found sleeping at the ambulance station, carbon monoxide poisoning."
Worker was assembling industrial racks and fell five feet to the ground below, striking his head on the concrete floor."
Worker slipped in the kitchen area.
Worker was running electrical lines through metal conduit and collapsed.
Worker was run over by co-worker while making grade measures.
Worker suffered fatal injuries after getting caught between forklift mast and 1600 lbs of baled cardboard.
Worker was fatally injured after getting caught in between while connecting a second trailer to a lead trailer.
Worker was found near an electrical enclosure, unresponsive."
Worker was installing a tire on a truck.  The tire exploded, striking the worker."
Worker was performing maintenance work on a water pump and was electrocuted.
Worker was hung by a safety strap while working on an extended boom lift, after the boom snapped."
Worker was crushed by an industrial truck that fell on him.
Worker was standing on the edge of the roof and fell 60 feet.
Worker was tracing an electrical short and contact was made with the live circuit.
Worker was electrocuted after making contact with a 110-volt doorbell transformer while performing A/C service.
Worker was stabbed and murdered at delivery site.
Worker was electrocuted after cutting into an energized electric line while working in the attic of a residence.
Worker was operating a machine and was pulled through the machine.
Worker was run over by truck.
Worker suffered fatal injuries (burns) consistent with electrocution while working 35 to 40 feet into a crawl space while attempting to repair water heater.
Worker was operating a riding lawn mower.  The lawn mower went into a pond, pinning the worker under it."
Worker was in the process of installing a backup generator and was electrocuted.
Worker was performing welding repairs on the log selector gate and was crushed by the gate.  The equipment was not properly locked and tagged out for maintenance.
Worker received fatal head injuries while loading a tractor on a trailer for hauling.
Worker received fatal injuries after being run over by a road grader.
Worker had been cleaning out a trench to install sprinkler lines and was later found unresponsive.  Death under investigation.
Worker was found unresponsive after taking pictures at a new maintenance building.  Electrical burns found on body during autopsy.  Possible electrocution.
Worker's tractor rolled into a canal.
Worker was performing maintenance on a rig.  The rig's floor came down, striking the worker on the head."
Worker was installing a drain pipe to a tank and collapsed.
Worker was removing a large tree that caused outages.  Worker was in the bucket and made contact with a live line at shoulder or hand.
Worker received fatal injuries from equipment roll-over while trying to set a beam on top of small building.
Worker was operating a mower and mowing grass near a canal.  The lawn mower rolled into the canal, worker drowned."
Worker was caught between two trucks and crushed.
Worker was greasing the bearings on a conveyor and fell 50 feet from a catwalk.
Worker was pulled into a tree chipper machine.
Worker was flagging traffic and was struck by a truck.
Worker discovered a fire in a sawdust collection system and attempted to extinguish the fire by opening the dump doors on the bottom of the sawdust collector and a flash fire occurred, enveloping the worker in flames/burning sawdust."
Worker was working on a water tower when he fell resulting in fatal injuries.
Worker was pinned by aerial lift and beam.
Worker collapsed after unloading 11-gallon plants and 15-gallon trees from truck.
Worker was working on a planer and was pinned by the door used to access the cutting heads.
Worker was in the process of assembling a steel double billboard.  One billboard fell onto another, pinning the worker between the signs."
Worker was performing maintenance on the back of a trash truck.  The support gave way and the tailgate came down on the worker.
Worker was working from an elevated platform and was descending a ladder from the platform.  Worker was found later hanging in his harness.
Worker suffered fatal head injuries after falling 10 feet from a ladder while climbing to retrieve some material.
Worker was electrocuted after making contact with an overhead power line while securing a de-limbed tree from a boom truck basket.
Worker suffered fatal injuries while operating a reciprocating saw on a ladder, losing his balance and falling 24 feet to a concrete slab."
Worker was struck by a pallet with a load weighing 2000 lbs.
Worker was washing trucks from an elevated platform 9 feet high and was found lying at the bottom of the platform.
Worker was struck by a steel beam that fell from a building to the ground.
Worker climbed a rolling stepladder to retrieve stock from an overhead rack.  He lost his balance and fell, striking his head on a beam and landing on the concrete below."
Worker was engaged in tree removal activities.  The tree snapped in half at the base; the worker was still attached to the tree as it fell to the driveway.
Worker was performing maintenance on skid steer and was later found pinned between the lifting arms and the cab of the skid steer.
Worker using a riding lawn mower rolled over into a lake and drowned.
Worker suffered fatal injuries after being crushed between two farm vehicles.
Worker was test-starting an engine to put in sidewinder.  The fan blade came off, striking the worker on the chest and head."
Worker was struck by two bar joists that fell from a load of steel bar joists on a flatbed truck.
Worker was tearing off and installing a new roof.  He stepped backward off the roof, falling 12 feet to a concrete patio."
Worker was painting a fascia board and fell from an extension ladder.
Worker was servicing a van.  The van rolled off of the ramps, pinning him between the muffler, transmission of the van, and the auto creeper."
Worker was assigned to operate a commercial printer.
Worker suffered fatal injuries after being struck by a moving semi truck while loading/unloading freight.
Worker was trimming a tree limb 25 feet high. The limb sprung back and struck him on the chest.
Worker was replacing a metal roof and fell through a skylight.
Worker was in the process of reroofing and fell from the second story roof.
Worker was working inside a grain silo in removal of the grain by manually moving wood slats covering the discharge auger.  Worker was standing on the grating and was unhooking a sensor cable from the grating.  The grating came loose; the worker fell and was pulled into the operations discharger auger.
Worker fell 30 feet after the scaffold collapsed.
Worker was performing repair operations on an impact attenuator and was struck by a truck.
Worker was operating a backhoe at a gravel pit to load gravel into the bed of a dump truck.  Worker exited the backhoe that was still running and got beneath the front bucket of the backhoe.  The bucket fell, crushing the worker."
Worker was doing electrical work and was exposed to an arc flash.
Worker sustained fatal injuries after being hit by a trailer on company property.
Worker suffered fatal injuries in a roll-over accident while backing down a hillside.  Worker not wearing seatbelt.
Worker sustained fatal injuries after being crushed by forklift that he was operating.  The forklift lost control in a skid down a hill, throwing the worker who was not wearing a seatbelt.  The forklift landed on and crushed the worker."
Worker worked as part of an industrial cleaning crew.  After leaving the work site, he collapsed, exhibiting signs of heat stroke."
Worker was working from a scissor lift installing conduit and came in contact with overhead crane rail conductors that were energized.  Worker was electrocuted.
Worker fell, hitting her head on cabinet before hitting floor."
Worker was delivering a load of propane. A piping failure occurred causing a leak, a series of explosions, and a fire.  Worker was caught in fire."
Worker was in the process of running casing. A high pressure hose burst, striking the worker and knocking him down the rig steps, 20 to 25 feet."
Worker was conducting pH balance tests of an indoor pool and had a heart attack.
Worker was working at a network junction box.  He was pinned between his work van and the junction box after the vehicle rolled forward.
Worker was digging up an underground electrical conduit.  He reached into the ground, grabbing the conduit and was electrocuted."
Worker was assisting with vacuum operation and fell into the boot pit, 20 feet."
Worker fell from a roof.
Worker was installing a light fixture, received an electrical shock, and fell from a ladder."
Worker was installing a satellite dish and received an electric shock from an unknown source.
Worker was on a pallet supported by a forklift working on a potato storage door and was crushed, falling to the ground."
Worker was in a 12-foot deep section of a trench in the process of lowering and connecting a section.  A large portion of the wall gave way, covering the worker up to his shoulders."
Worker was changing out a ballast and capacitor for an outdoor floodlight with 277 volts and was electrocuted.
Worker, during highway paving operations, was backed over by a loaded dump truck."
Worker was conducting testing and exposed to 270-volt supplied conductors contained in an electrical box and was electrocuted.
Worker was using a pressure testing device.  Tool inside went one direction and the vessel went in another, striking the worker's torso."
Worker was in the process of backing up a trailer to another trailer to unload a rig.  Worker was crushed after one of the trailers backed up pinning him against the opposite trailer.