# generated by Slic3r 1.2.9 on Tue Apr  5 12:42:30 2016

[filament:DAVINCI ABS]
bed_temperature = 100
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 0.9
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FF0000
filament_diameter = 1.75
first_layer_bed_temperature = 120
first_layer_temperature = 230
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 5
slowdown_below_layer_time = 45
temperature = 220

[filament:DAVINCI PLA]
bed_temperature = 60
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 0.9
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FF0000
filament_diameter = 1.75
first_layer_bed_temperature = 60
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 5
slowdown_below_layer_time = 45
temperature = 190

[filament:TPU]
bed_temperature = 70
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 0.9
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FF0000
filament_diameter = 1.75
first_layer_bed_temperature = 70
first_layer_temperature = 240
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 5
slowdown_below_layer_time = 45
temperature = 240

[presets]
filament = DAVINCI ABS.ini
print = Davinci 1.0 ABS.ini
printer = DAVINCI.ini

[print:Davinci 1.0 ABS]
avoid_crossing_perimeters = 1
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 2
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 0
external_fill_pattern = concentric
external_perimeter_extrusion_width = 0
external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 90%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 0.5
first_layer_height = 0.35
first_layer_speed = 50%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 5%
infill_speed = 60
interface_shells = 0
layer_height = 0.1
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 0
skirt_height = 1
skirts = 1
small_perimeter_speed = 10
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 45
support_material_contact_distance = 0.2
support_material_enforce_layers = 10
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 1
support_material_interface_spacing = 0
support_material_interface_speed = 30
support_material_pattern = honeycomb
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 45
thin_walls = 1
threads = 2
top_infill_extrusion_width = 105%
top_solid_infill_speed = 20
top_solid_layers = 5
travel_speed = 100
xy_size_compensation = 0

[print:TPU]
avoid_crossing_perimeters = 1
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 30
brim_width = 2
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 0
external_fill_pattern = concentric
external_perimeter_extrusion_width = 0
external_perimeter_speed = 15
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 90%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 0.5
first_layer_height = 0.35
first_layer_speed = 50%
gap_fill_speed = 5
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 5%
infill_speed = 30
interface_shells = 0
layer_height = 0.2
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 0
skirt_height = 1
skirts = 1
small_perimeter_speed = 5
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 10
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 1
support_material_interface_spacing = 0
support_material_interface_speed = 15
support_material_pattern = honeycomb
support_material_spacing = 1.5
support_material_speed = 20
support_material_threshold = 74
thin_walls = 1
threads = 2
top_infill_extrusion_width = 105%
top_solid_infill_speed = 10
top_solid_layers = 5
travel_speed = 100
xy_size_compensation = 0

[print:small fine .1mm no supp]
avoid_crossing_perimeters = 1
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 20
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 0
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 10%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.35
first_layer_speed = 30%
gap_fill_speed = 10
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 70
interface_shells = 0
layer_height = 0.1
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process =
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 20
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 50
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 20
top_solid_layers = 4
travel_speed = 150
xy_size_compensation = 0

[printer:DAVINCI]
bed_shape = 0x0,200x0,200x200,0x200
before_layer_gcode =
end_gcode = M117 HOLY SHIT WE'RE FINALLY DONE\nG92 E0 ; reset extrusion distance\nM104 S0 ; turn off extruder\nM140 S0 ; turn off Bed\nG90 ; Absolute\nG28 X0 Y0 ; home\nM117 GOING DOWN BITCHES\nG1 Z200 ; Lower bed\nM117 Cleaning\nM100 ;Cleaning\nM84 ; Disable motors\nM117 COOLING DOWN, DON'T TOUCH ME ASSHOLE\nM117 GET THIS SHIT OFF OF ME\nM300 s2800 p300\nM300 s2900 p100\nM300 s2400 p250\nM300 s2700 p1500\nM300 s3000 p300\nM300 s2900 p100\nM300 s2400 p250\nM300 s2700 p1500\nM300 s2800 p300\nM300 s2900 p100\nM300 s2400 p250\nM300 s2700 p1500\nM300 s3000 p300\nM300 s2900 p100\nM300 s2400 p250\nM300 s2700 p1500\nM84 ; Disable motors\nM117 I'M DONE FUCKER
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
nozzle_diameter = 0.4
octoprint_apikey =
octoprint_host =
pressure_advance = 0
retract_before_travel = 0
retract_layer_change = 1
retract_length = 0.3
retract_length_toolchange = 10
retract_lift = 0.3
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 300
start_gcode = M140 S[first_layer_bed_temperature] ; Bed (no wait)\nM106 S255 ; Start fan\nG90 ; set absolute coordinates\nG28 ; home all axis\nM104 S[first_layer_temperature] ; Extruder (no wait)\nM190 S[first_layer_bed_temperature] ; Bed (wait)\nM109 S[first_layer_temperature] ; Extruder (wait)\nM300 S294 P200 ;D4: 294\nM300 S588 P200 ;D5: 588\nM300 S440 P200 ;A4: 440\nM300 S392 P200 ;G4: 392\nM300 S784 P200 ;G5: 784\nM300 S440 P200 ;A4: 440\nM300 S740 P200 ;F#5: 740\nM300 S440 P200 ;A4: 440\n;------------------------\nM300 S294 P200 ;D4: 294\nM300 S588 P200 ;D5: 588\nM300 S440 P200 ;A4: 440\nM300 S392 P200 ;G4: 392\nM300 S784 P200 ;G5: 784\nM300 S440 P200 ;A4: 440\nM300 S740 P200 ;F#5: 740\nM300 S440 P200 ;A4: 440\nM300 S330 P200 ;E4: 330\nM300 S588 P200 ;D5: 588\nM300 S440 P200 ;A4: 440\nM300 S392 P200 ;G4: 392\nM300 S784 P200 ;G5: 784\nM300 S440 P200 ;A4: 440\nM300 S740 P200 ;F#5: 740\nM300 S440 P200 ;A4: 440\n;------------------------\nM300 S330 P200 ;E4: 330\nM300 S588 P200 ;D5: 588\nM300 S440 P200 ;A4: 440\nM300 S392 P200 ;G4: 392\nM300 S784 P200 ;G5: 784\nM300 S440 P200 ;A4: 440\nM300 S740 P200 ;F#5: 740\nM300 S440 P200 ;A4: 440\n;------------------------\nM300 S392 P200 ;G4: 392\nM300 S588 P200 ;D5: 588\nM300 S440 P200 ;A4: 440\nM300 S392 P200 ;G4: 392\nM300 S784 P200 ;G5: 784\nM300 S440 P200 ;A4: 440\nM300 S740 P200 ;F#5: 740\nM300 S440 P200 ;A4: 440\n;------------------------\nM300 S392 P200 ;G4: 392\nM300 S588 P200 ;D5: 588\nM300 S440 P200 ;A4: 440\nM300 S392 P200 ;G4: 392\nM300 S784 P200 ;G5: 784\nM300 S440 P200 ;A4: 440\nM300 S740 P200 ;F#5: 740\nM300 S440 P200 ;A4: 440\nM300 S294 P800 ;D4: 294\nM117 LET ME CLEAN MY NOZZLE\nM100 ; Cleaning\nG1 Z5 F1500\nG1 X0 Y20 F1000\nG1 X32 Y35 F1000\nG92 E0 ; reset extrusion distance\nG1 Z[first_layer_height] F4800.000\nM117 I'M MAKING THIS FOR YOU!
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 1
z_offset = 0

[printer:DAVINCI ABS]
bed_shape = 0x0,200x0,200x200,0x200
before_layer_gcode =
end_gcode = M117 HOLY SHIT WE'RE FINALLY DONE\nG92 E0 ; reset extrusion distance\nM104 S0 ; turn off extruder\nM140 S0 ; turn off Bed\nG90 ; Absolute\nG28 X0 Y0 ; home\nM117 GOING DOWN BITCHES\nG1 Z200 ; Lower bed\nM117 Cleaning\nM100 ;Cleaning\nM84 ; Disable motors\nM117 COOLING DOWN, DON'T TOUCH ME ASSHOLE\nM190 S55 ; Bed (cooling)\nM116 ; Wait for all temperatures\nM140 S0 ; turn off Bed\nM117 GET THIS SHIT OFF OF ME\nM300 s2800 p300\nM300 s2900 p100\nM300 s2400 p250\nM300 s2700 p1500\nM300 s3000 p300\nM300 s2900 p100\nM300 s2400 p250\nM300 s2700 p1500\nM300 s2800 p300\nM300 s2900 p100\nM300 s2400 p250\nM300 s2700 p1500\nM300 s3000 p300\nM300 s2900 p100\nM300 s2400 p250\nM300 s2700 p1500\nM84 ; Disable motors\nM117 Printer Ready
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
nozzle_diameter = 0.4
octoprint_apikey =
octoprint_host =
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 0
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = M140 S[first_layer_bed_temperature] ; Bed (no wait)\nM106 S255 ; Start fan\nG90 ; set absolute coordinates\nG28 ; home all axis\nM104 S[first_layer_temperature] ; Extruder (no wait)\nM190 S[first_layer_bed_temperature] ; Bed (wait)\nM109 S[first_layer_temperature] ; Extruder (wait)\nM117 Start, JOHN CENA\nM300 s2800 p300\nM300 s2900 p100\nM300 s2400 p250\nM300 s2700 p1500\nM300 s3000 p300\nM300 s2900 p100\nM300 s2400 p250\nM300 s2700 p1500\nM300 s2800 p300\nM300 s2900 p100\nM300 s2400 p250\nM300 s2700 p1500\nM300 s3000 p300\nM300 s2900 p100\nM300 s2400 p250\nM300 s2700 p1500\nM117 LET ME CLEAN MY NOZZLE\nM100 ; Cleaning\nG1 Z5 F1500\nG1 X0 Y20 F1000\nG1 X32 Y35 F1000\nG92 E0 ; reset extrusion distance\nG1 Z[first_layer_height] F4800.000\nG1 X32 Y175 E14 F1000\nG1 X32 Y190 F1000\nM117 I'M MAKING THIS FOR YOU!
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:Simple Mode]
bed_shape = 0x0,200x0,200x200,0x200
end_gcode = M117 Done\nG92 E0 ; reset extrusion distance\nM104 S0 ; turn off extruder\nM140 S0 ; turn off Bed\nG90 ; Absolute\nG28 X0 Y0 ; home\nM117 Down Bed\nG1 Z200 ; Lower bed\nM117 Cleaning\nM100 ;Cleaning\nM84 ; Disable motors\nM117 Cooling\nM190 S55 ; Bed (cooling)\nM116 ; Wait for all temperatures\nM140 S0 ; turn off Bed\nM117 Pickup piece\nM300 s2500 p400 ; Beep\nM300 s2000 p400\nM300 s1500 p400\nM300 s1000 p400\nM84 ; Disable motors\nM117 Printer Ready
gcode_flavor = reprap
nozzle_diameter = 0.4
retract_length = 1
retract_lift = 0
start_gcode = M140 S[first_layer_bed_temperature] ; Bed (no wait)\nM106 S255 ; Start fan\nG90 ; set absolute coordinates\nG28 ; home all axis\nM190 S[first_layer_bed_temperature] ; Bed (wait)\nM104 S[first_layer_temperature] ; Extruder (no wait)\nM109 S[first_layer_temperature] ; Extruder (wait)\nM117 Start\nM300 s1000 p400 ; Beep\nM300 s1500 p400\nM300 s2000 p400\nM300 s2500 p400\nm300 s3000 p400\nm300 s3500 p400\nm300 s4000 p400\nM117 Cleaning\nM100 ; Cleaning\nG1 Z5 F1500\nG1 X0 Y20 F1000\nG1 X32 Y35 F1000\nG92 E0 ; reset extrusion distance\nG1 Z[first_layer_height] F4800.000\nG1 X32 Y175 E14 F1000\nG1 X32 Y190 F1000\nM117 Printing
wipe = 0
z_offset = 0

[settings]
autocenter = 1
mode = expert

[simple]
avoid_crossing_perimeters = 1
bed_shape = 0x0,200x0,200x200,0x200
bed_temperature = 80
before_layer_gcode =
bottom_solid_layers = 5
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 3
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = M117 Done\nG92 E0 ; reset extrusion distance\nM104 S0 ; turn off extruder\nM140 S0 ; turn off Bed\nG90 ; Absolute\nG28 X0 Y0 ; home\nM117 Down Bed\nG1 Z200 ; Lower bed\nM117 Cleaning\nM100 ;Cleaning\nM84 ; Disable motors\nM117 Cooling\nM190 S55 ; Bed (cooling)\nM116 ; Wait for all temperatures\nM140 S0 ; turn off Bed\nM117 Pickup piece\nM300 s2500 p400 ; Beep\nM300 s2000 p400\nM300 s1500 p400\nM300 s1000 p400\nM84 ; Disable motors\nM117 Printer Ready
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 1.75
fill_angle = 45
fill_density = 10%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 90
first_layer_extrusion_width = 200%
first_layer_height = 0.4
first_layer_speed = 30
first_layer_temperature = 230
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 10
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 10
interface_shells = 0
layer_gcode =
layer_height = 0.1
max_fan_speed = 100
max_print_speed = 80
max_volumetric_speed = 0
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 0
notes =
nozzle_diameter = 0.4
octoprint_apikey =
octoprint_host =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 10
perimeters = 2
post_process =
pressure_advance = 0
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 0
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 5
small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = M140 S[first_layer_bed_temperature] ; Bed (no wait)\nM106 S255 ; Start fan\nG90 ; set absolute coordinates\nG28 ; home all axis\nM190 S[first_layer_bed_temperature] ; Bed (wait)\nM104 S[first_layer_temperature] ; Extruder (no wait)\nM109 S[first_layer_temperature] ; Extruder (wait)\nM117 Start\nM300 s1000 p400 ; Beep\nM300 s1500 p400\nM300 s2000 p400\nM300 s2500 p400\nm300 s3000 p400\nm300 s3500 p400\nm300 s4000 p400\nM117 Cleaning\nM100 ; Cleaning\nG1 Z5 F1500\nG1 X0 Y20 F1000\nG1 X32 Y35 F1000\nG92 E0 ; reset extrusion distance\nG1 Z[first_layer_height] F4800.000\nG1 X32 Y175 E14 F1000\nG1 X32 Y190 F1000\nM117 Printing
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
temperature = 221
thin_walls = 1
threads = 2
toolchange_gcode =
top_infill_extrusion_width = 0
top_solid_infill_speed = 15
top_solid_layers = 3
travel_speed = 10
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
xy_size_compensation = 0
z_offset = 0