9100g ICS chinese

The method described below, the National Bank I9100GZCKI1 applicable, I pro-test, no line l this version, upgrade and then brush the other versions of whether this method I have not tried, would like to use.

Complete the root need to download the four files

First to my network disk to download the following four files:

1, Odin3 v1.85.exe (Brush the main program file)

2 the, Odin3.ini (RUU profile)

3 the, i9100G_ZCKI1_KERNEL_CWM_ROOT.tar (root kernel Brush to take line as root)

4, i9100G_ZCKI1_KERNEL.tar (the original kernel, after the brush machine root boot exclamation mark)

Download these four files: ht * tp :/ / dl.dbank.com/c0xaizxpbo (remove the asterisk)

Note: The download do not need to unzip the download is complete spare

Second, download Samsung pc suite Samsung Kies, mainly to use his driver installed Kies driver installed, you can plug in data cable to try the computer the possibility of normal communication with the mobile phone, you can not download the Samsung Kies directly in the Samsung USB driver installation, in short, the computer can identify the phone line, Internet search.

Make sure your phone's USB debug mode has been closed (applications -> Settings -> Applications -> Development -> USB Debugging -> untick)

Phone off, press and hold [Volume -] [Home (main screen)] key, press the [Power] key to boot, you will see a warning in English screen, release the [Volume -] and [Home (main screen )] key, then release the [power] key to enter bootloader mode, (many of the Friends of the machine can not brush machine model is the first release the power lead to boot).

The operation was successful see the figure below:

Press 【VOL +】, Odin brush machine mode.

The operation was successful see the figure below:

So far, the mobile terminal operation suspended.

Now to the computer side, running Odin3 v1.85.exe, connect the data cable in the lower left corner of the the Odin3 v1.85.exe interface message when the computer can correctly identify the phone that appears in Figure added the words, and the ID: COM below The first box yellow shows the port number to connect. See below:

Odin interface, check the "Auto reboot", "F. Reset Time" and "PDA", other parts are not ticked, then press the "PDA" button, choose to brush write the i9100G_ZCKI1_KERNEL_CWM_ROOT.tar of the file, and then "START" button to start brushing machine, the upper left solution will be the green progress bar on the phone but also the degree of progress show that after the completion of the Brush, Odin, the upper left corner there will be "PASS!" words, as shown:

The phone will automatically restart unplug the cable, the completion of the brush, then root successfully, but there will be a yellow exclamation point warning message when the phone is switched on, but does not affect use. Repeat the above Brush steps, but in step "4", select the file you want to brush written i9100G_ZCKI1_KERNEL.tar ", as shown below:


After brushing to remove the yellow exclamation mark, bringing the brush to complete!


Below said brush machine fails, the phone is switched to a phone icon and a computer icon in the middle with a yellow exclamation point, the following prompt "Software update failed" - that is to say "brick" remedies. Brush with the above described is basically the same, therefore, outside the map, because I was lazy, but I think if you have been using the above way to brush off the machine, see the following text description will not be any problem.

A phone is switched on the display when the phone appear above said "a phone icon and a Computer icon, in the middle with a yellow exclamation point, the following prompt 'software update failed', plug the data cable, to open Odin3 on the computer, then if you're lucky, in Odin3 interface described above, the "ID: COM below the first box appear in yellow has been connected to the port number, I brush machine when there had been such a situation, is to use the following successful repair (Note: If you did not show the port number displayed in this yellow, then the method described below is not valid).

First, to my network disk download the following files:

1, omap4_all_20110627_CHN_OPEN_emmc.pit

2, APBOOT_I9100GZCKH4_CL484595_REVr07_user_low_ship.tar.md5 the

3, CODE_I9100GZCKH4_CL484595_REVr07_user_low_ship.tar.md5 the

4, MODEM_I9100GZCKH4_REV_00_CL1050825.tar.md5 the

5, GT-I9100G-CSC-MULTI-OZHKH4.tar.md5

Download: ht * tp :/ / dl.dbank.com/c0a7p5vpjj (remove the asterisk)

Appear when the phone is a phone icon and a computer icon, in the middle with a yellow exclamation mark, the following prompt 'software update failed' "After this case, connect the data cable to open Odin3 When the display is connected port number, check: Re-Pratition "," Auto reboot "," F. Reset Time ", checked: BOOTLOADER, PDAs, the PHONE, the CSC. Point PIT button, select the file: omap4_all_20110627_CHN_OPEN_emmc.pit the point BOOTLOADER button, select file: APBOOT_I9100GZCKH4_CL484595_REVr07_user_low_ship.tar.md5, point PDA button, select file: CODE_I9100GZCKH4_CL484595_REVr07_user_low_ship.tar.md5, point PHONE button, select the file: MODEM_I9100GZCKH4_REV_00_CL1050825.tar.md5 CSC button, select the file: GT the-I9100G-the CSC-MULTI-OZHKH4.tar.md5, and then point the START button to start the brush normal, then you should already see the progress of the Brush, to be green the PASS! After the words, Congratulations on your already successful repair of heavy brush machine, the phone is no longer a brick.

Provided in the package download of to upgrade ZCKI1 ZCKH4 with Odin3 Brush Brush Brush package the original ZCKI1 I extract upgrade using KIES, Brush package. Download: ht * tp :/ / dl.dbank.com/c0micsahda (remove *)

The package of this brush just brush the PDA can only check the Auto reboot "," F. Reset Time "and" PDA ", other parts do not tick.