Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- <4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- <5>[ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
- <6>[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- <6>[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- <6>[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- <6>[ 0.000000] Writing ErrCtl register=00000000
- <6>[ 0.000000] Readback ErrCtl register=00000000
- <6>[ 0.000000] Memory: 61040k/65536k available (2453k kernel code, 4496k reserved, 578k data, 228k init, 0k highmem)
- <6>[ 0.000000] NR_IRQS:83
- <6>[ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
- <6>[ 0.080000] pid_max: default: 32768 minimum: 301
- <6>[ 0.080000] Mount-cache hash table entries: 512
- <6>[ 0.090000] NET: Registered protocol family 16
- <6>[ 0.100000] found calibration data for slot 0 on 0xBF051000
- <4>[ 0.110000] registering PCI controller with io_map_base unset
- <6>[ 0.130000] bio: create slab <bio-0> at 0
- <6>[ 0.130000] usbcore: registered new interface driver usbfs
- <6>[ 0.140000] usbcore: registered new interface driver hub
- <6>[ 0.140000] usbcore: registered new device driver usb
- <6>[ 0.150000] PCI host bridge to bus 0000:00
- <6>[ 0.150000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
- <6>[ 0.160000] pci_bus 0000:00: root bus resource [io 0x0000]
- <6>[ 0.160000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- <7>[ 0.170000] pci 0000:00:00.0: [168c:002a] type 00 class 0x028000
- <6>[ 0.170000] pci 0000:00:00.0: fixup device configuration
- <0>[ 0.170000] bootstrap returns device 168C:2A
- <7>[ 0.180000] pci 0000:00:00.0: reg 10: [mem 0x10000000-0x1000ffff 64bit]
- <7>[ 0.180000] pci 0000:00:00.0: supports D1
- <7>[ 0.180000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
- <7>[ 0.180000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
- <6>[ 0.180000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
- <6>[ 0.180000] pci 0000:00:00.0: using irq 72 for pin 1
- <6>[ 0.190000] Switching to clocksource MIPS
- <6>[ 0.190000] NET: Registered protocol family 2
- <6>[ 0.200000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
- <6>[ 0.200000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
- <6>[ 0.210000] TCP: Hash tables configured (established 512 bind 512)
- <6>[ 0.210000] TCP: reno registered
- <6>[ 0.220000] UDP hash table entries: 256 (order: 0, 4096 bytes)
- <6>[ 0.220000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- <6>[ 0.230000] NET: Registered protocol family 1
- <7>[ 0.230000] PCI: CLS 0 bytes, default 32
- <5>[ 0.230000] gpio_proc: module loaded and /proc/gpio/ created
- <5>[ 0.240000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
- <6>[ 0.250000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
- <6>[ 0.260000] msgmni has been set to 119
- <6>[ 0.260000] io scheduler noop registered
- <6>[ 0.260000] io scheduler deadline registered (default)
- <6>[ 0.270000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
- <6>[ 0.300000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
- <6>[ 0.300000] console [ttyS0] enabled, bootconsole disabled
- <4>[ 0.320000] check spi banks 2
- <4>[ 0.320000] 0000 : C2 20 18
- <4>[ 0.320000] found MX25L128-45E device on bank#0
- <4>[ 0.330000] 0000 : C2 20 18
- <4>[ 0.330000] found MX25L128-45E device on bank#1
- <4>[ 0.330000] SPI flash size total:32 Mbytes
- <0>[ 0.410000]
- <0>[ 0.410000] found squashfs at 179000
- <5>[ 0.420000] Creating 9 MTD partitions on "ar7240-nor0":
- <5>[ 0.420000] 0x000000000000-0x000000050000 : "RedBoot"
- <5>[ 0.430000] 0x000000060000-0x000001fe0000 : "linux"
- <5>[ 0.440000] 0x000000179000-0x000001bb0000 : "rootfs"
- <4>[ 0.440000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
- <5>[ 0.460000] mtd: partition "rootfs" set to be root filesystem
- <5>[ 0.460000] 0x000001bb0000-0x000001fe0000 : "ddwrt"
- <5>[ 0.470000] 0x000001fe0000-0x000001ff0000 : "nvram"
- <5>[ 0.480000] 0x000001ff0000-0x000002000000 : "FIS directory"
- <5>[ 0.480000] 0x000001ff0000-0x000002000000 : "board_config"
- <5>[ 0.490000] 0x000000000000-0x000002000000 : "fullflash"
- <5>[ 0.500000] 0x000000040000-0x000000050000 : "uboot-env"
- <6>[ 0.500000] tun: Universal TUN/TAP device driver, 1.6
- <6>[ 0.510000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- <7>[ 0.520000] ar71xx: pll_reg 0xb805002c: 0x62000000
- <6>[ 0.720000] PPP generic driver version 2.4.2
- <6>[ 0.720000] PPP BSD Compression module registered
- <6>[ 0.730000] PPP Deflate Compression module registered
- <6>[ 0.730000] PPP MPPE Compression module registered
- <6>[ 0.740000] NET: Registered protocol family 24
- <6>[ 0.750000] u32 classifier
- <6>[ 0.760000] Performance counters on
- <6>[ 0.760000] input device check on
- <6>[ 0.760000] Actions configured
- <6>[ 0.770000] Netfilter messages via NETLINK v0.30.
- <6>[ 0.770000] nf_conntrack version 0.5.0 (953 buckets, 3812 max)
- <4>[ 0.780000] nf_conntrack_rtsp v0.6.21 loading
- <4>[ 0.780000] nf_nat_rtsp v0.6.21 loading
- <6>[ 0.790000] ip_tables: (C) 2000-2006 Netfilter Core Team
- <6>[ 0.790000] TCP: westwood registered
- <6>[ 0.800000] TCP: hybla registered
- <6>[ 0.800000] TCP: vegas registered
- <6>[ 0.800000] NET: Registered protocol family 17
- <5>[ 0.810000] Bridge firewalling registered
- <6>[ 0.810000] 8021q: 802.1Q VLAN Support v1.8
- <6>[ 0.820000] searching for nvram
- <6>[ 0.820000] nvram size = 0
- <6>[ 0.900000] Atheros AR71xx hardware watchdog driver version 0.1.0
- <6>[ 0.900000] ar71xx-wdt: timeout=15 secs (max=21) ref freq=200000000
- <6>[ 0.920000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- <6>[ 0.920000] Freeing unused kernel memory: 228K (80357000 - 80390000)
- <7>[ 4.150000] ar71xx-wdt: enabling watchdog timer
- <6>[ 4.240000] switch0: Atheros AR8316 rev. 1 switch registered on ag71xx-mdio.0
- <6>[ 4.250000] libphy: ag71xx_mdio: probed
- <6>[ 4.840000] ar8316: Using port 4 as switch port
- <6>[ 4.840000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
- <6>[ 4.860000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
- <6>[ 5.330000] Loading modules backported from Linux version master-2015-10-26-0-g28c26cb
- <6>[ 5.340000] Backport generated by backports.git backports-20150903-4-g12cf266
- <6>[ 5.520000] cfg80211: World regulatory domain updated:
- <6>[ 5.520000] cfg80211: DFS Master region: unset
- <6>[ 5.530000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
- <6>[ 5.540000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 5.550000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 5.550000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 5.560000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 5.570000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 5.580000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
- <4>[ 6.240000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
- <7>[ 6.250000] ath: EEPROM regdomain: 0x0
- <7>[ 6.250000] ath: EEPROM indicates default country code should be used
- <7>[ 6.250000] ath: doing EEPROM country->regdmn map search
- <7>[ 6.250000] ath: country maps to regdmn code: 0x3a
- <7>[ 6.250000] ath: Country alpha2 being used: US
- <7>[ 6.250000] ath: Regpair used: 0x3a
- <7>[ 6.280000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
- <6>[ 6.280000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=72
- <6>[ 6.290000] cfg80211: Regulatory domain changed to country: US
- <6>[ 6.300000] cfg80211: DFS Master region: FCC
- <6>[ 6.300000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
- <6>[ 6.310000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
- <6>[ 6.320000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
- <6>[ 6.330000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
- <6>[ 6.340000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
- <6>[ 6.350000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
- <6>[ 6.740000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- <6>[ 6.780000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
- <6>[ 6.790000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
- <4>[ 6.800000] ehci_reset Intialize USB CONTROLLER in host mode: 3
- <4>[ 6.800000] ehci_reset Port Status c000000
- <6>[ 6.840000] eth0: link up (1000Mbps/Full duplex)
- <6>[ 6.840000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
- <6>[ 6.870000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
- <0>[ 6.870000] switch USB LED Off
- <6>[ 6.870000] hub 1-0:1.0: USB hub found
- <6>[ 6.880000] hub 1-0:1.0: 1 port detected
- <6>[ 7.060000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- <0>[ 7.200000] switch USB LED On
- <6>[ 7.200000] usb 1-1: new high-speed USB device number 2 using ar71xx-ehci
- <5>[ 7.480000] SCSI subsystem initialized
- <6>[ 7.820000] usb-storage 1-1:1.0: USB Mass Storage device detected
- <6>[ 7.830000] scsi0 : usb-storage 1-1:1.0
- <6>[ 7.840000] usbcore: registered new interface driver usb-storage
- <6>[ 8.840000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 1 is up
- <6>[ 8.840000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 2 is up
- <6>[ 8.850000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
- <6>[ 8.860000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 5 is up
- <5>[ 8.860000] scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
- <5>[ 8.880000] sd 0:0:0:0: [sda] 3913728 512-byte logical blocks: (2.00 GB/1.86 GiB)
- <5>[ 8.890000] sd 0:0:0:0: [sda] Write Protect is off
- <7>[ 8.890000] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
- <3>[ 8.890000] sd 0:0:0:0: [sda] No Caching mode page found
- <3>[ 8.900000] sd 0:0:0:0: [sda] Assuming drive cache: write through
- <3>[ 8.910000] sd 0:0:0:0: [sda] No Caching mode page found
- <3>[ 8.910000] sd 0:0:0:0: [sda] Assuming drive cache: write through
- <6>[ 9.010000] sda: sda1 sda2
- <3>[ 9.050000] sd 0:0:0:0: [sda] No Caching mode page found
- <3>[ 9.060000] sd 0:0:0:0: [sda] Assuming drive cache: write through
- <5>[ 9.060000] sd 0:0:0:0: [sda] Attached SCSI removable disk
- <4>[ 9.890000] EXT2-fs (sda1): warning: mounting unchecked fs, running e2fsck is recommended
- <6>[ 10.840000] device br0 entered promiscuous mode
- <6>[ 11.010000] device vlan1 entered promiscuous mode
- <6>[ 11.010000] device eth0 entered promiscuous mode
- <6>[ 11.020000] br0: port 1(vlan1) entered forwarding state
- <6>[ 11.030000] br0: port 1(vlan1) entered forwarding state
- <6>[ 11.030000] device br0 left promiscuous mode
- <6>[ 11.050000] device br0 entered promiscuous mode
- <6>[ 11.070000] device br0 left promiscuous mode
- <3>[ 11.110000] cfg80211: Invalid regulatory domain detected:
- <6>[ 11.110000] cfg80211: Regulatory domain: 00
- <6>[ 11.120000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
- <6>[ 11.130000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 11.140000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 11.140000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 11.150000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 11.160000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 11.170000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
- <6>[ 11.190000] cfg80211: World regulatory domain updated:
- <6>[ 11.200000] cfg80211: DFS Master region: unset
- <6>[ 11.200000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
- <6>[ 11.210000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 11.220000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 11.230000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 11.230000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 11.240000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- <6>[ 11.250000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
- <6>[ 11.260000] cfg80211: Regulatory domain changed to country: US
- <6>[ 11.260000] cfg80211: DFS Master region: FCC
- <6>[ 11.270000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
- <6>[ 11.280000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
- <6>[ 11.290000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
- <6>[ 11.290000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
- <6>[ 11.300000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
- <6>[ 11.310000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
- <6>[ 13.940000] warning: `proftpd' uses 32-bit capabilities (legacy support in use)
- <6>[ 16.530000] device ath0 entered promiscuous mode
- <6>[ 18.050000] br0: port 2(ath0) entered forwarding state
- <6>[ 18.060000] br0: port 2(ath0) entered forwarding state
- <6>[ 18.070000] device ath0.1 entered promiscuous mode
- <6>[ 18.090000] br0: port 3(ath0.1) entered forwarding state
- <6>[ 18.090000] br0: port 3(ath0.1) entered forwarding state
- <6>[ 19.490000] device vlan2 entered promiscuous mode
- <6>[ 22.180000] device vlan2 left promiscuous mode
- <6>[ 26.080000] br0: port 1(vlan1) entered forwarding state
- <6>[ 33.080000] br0: port 2(ath0) entered forwarding state
- <6>[ 33.120000] br0: port 3(ath0.1) entered forwarding state
- <6>[15457.220000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement