[    0.000000]    1.150126] the wakeup pdata is 0xbfe73740
[    1.150422] add wake up source irq 75
[    1.157407] IMX usb wakeup probe
[    1.160728] the wakeup pdata is 0xbfe73a00
[    1.160820] cpu regulator mode:ldo_enable
[    1.165039] i.MXC CPU frequency driver
[    1.186789] VFS: Disk quotas dquot_6.5.2
[    1.191049] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.200044] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.206845] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    1.213928] aufs 3.0-20130325
[    1.216941] msgmni has been set to 1741
[    1.223477] alg: No test for stdrng (krng)
[    1.227877] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.235362] io scheduler noop registered
[    1.239318] io scheduler deadline registered
[    1.243676] io scheduler cfq registered (default)
[    1.248885] MIPI DSI driver module loaded
[    1.253020] mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi
[    1.259537] mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0xa:0xa0:0xc1
[    1.266459] fbcvt: 1920x1080@60: CVT Name - 2.073M9
[    1.271362] fb_videomode = 59 1920 1080 5780 328 128 3 32 200 5 2 0 32
[    1.289623] imx-ipuv3 imx-ipuv3.0: WARNING: adapt panel end blank lines
[    1.305812] imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
[    1.339131] imx-ipuv3 imx-ipuv3.0: WARNING: adapt panel end blank lines
[    1.373728] Console: switching to colour frame buffer device 160x64
[    1.421769] mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver ldb
[    1.428184] _regulator_get: get() with no identifier
[    1.439773] mxc_sdc_fb mxc_sdc_fb.2: register mxc display driver ldb
[    1.453247] imx-sdma imx-sdma: loaded firmware 1.1
[    1.460258] fbcvt: 1920x1080@60: CVT Name - 2.073M9
[    1.465157] fb_videomode = 59 1920 1080 5780 328 128 3 32 200 5 2 0 32
[    1.472287] imx-sdma imx-sdma: initialized
[    1.574066] Serial: IMX driver
[    1.574177] imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
[    1.574492] imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX
[    1.586508] fb_videomode = 59 640 480 39721 48 16 33 10 96 2 0 16 32
[    1.630914] fb_videomode = 60 1920 1080 6734 148 88 36 4 44 5 3 32 2
[    1.643642] console [ttymxc1] enabled, bootconsole disabled
[    1.780953] fb_videomode = 60 1920 1080 6734 148 88 36 4 44 5 3 32 32
[    1.780970] fb_videomode = 60 1920 1080 6734 148 88 36 4 44 5 3 32 2
[    1.838406] imx-uart.3: ttymxc3 at MMIO 0x21f0000 (irq = 61) is a IMX
[    1.848524] loop: module loaded
[    1.851670] request BOSSA_CLK IRQ
[    1.854987] registering IRQ 419 for BOSSAC Arduino erase/reset operation
[    1.862171] Loading iSCSI transport class v2.0-870.
[    1.867293] iscsi: registered transport (tcp)
[    1.914390] No sata disk.
[    1.917533] GPMI NAND driver registered. (IMX)
[    1.922327] vcan: Virtual CAN interface driver
[    1.926792] CAN device driver interface
[    1.930630] flexcan netdevice driver
[    1.934286] FEC Ethernet Driver
[    1.939843] fec_enet_mii_bus: probed
[    1.944231] usbcore: registered new interface driver rt2800usb
[    1.950146] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.956807] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[    1.963445] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[    1.995763] fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
[    2.015753] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[    2.021802] hub 1-0:1.0: USB hub found
[    2.025564] hub 1-0:1.0: 1 port detected
[    2.029662] add wake up source irq 72
[    2.033365] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
[    2.040013] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
[    2.085755] fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
[    2.115768] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
[    2.121762] hub 2-0:1.0: USB hub found
[    2.125523] hub 2-0:1.0: 1 port detected
[    2.129639] Initializing USB Mass Storage driver...
[    2.134590] usbcore: registered new interface driver usb-storage
[    2.140647] USB Mass Storage support registered.
[    2.145390] usbcore: registered new interface driver libusual
[    2.151246] usbcore: registered new interface driver usbserial
[    2.157125] USB Serial support registered for generic
[    2.162216] usbcore: registered new interface driver usbserial_generic
[    2.168761] usbserial: USB Serial Driver core
[    2.173121] ARC USBOTG Device Controller driver (1 August 2005)
[    2.179596] mousedev: PS/2 mouse device common for all mice
[    2.185567] i2c-core: driver [isl29023] using legacy suspend method
[    2.191857] i2c-core: driver [isl29023] using legacy resume method
[    2.198630] snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0
[    2.205220] i2c /dev entries driver
[    2.209183] Linux media interface: v0.10
[    2.213138] Linux video capture interface: v2.00
[    2.217989] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16
[    2.225529] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17
[    2.233160] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18
[    2.240758] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video19
[    2.248315] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video20
[    2.255958] vivi-000: V4L2 device registered as video0
[    2.261100] Video Technology Magazine Virtual Video Capture Board ver 0.8.0 successfully loaded.
[    2.270058] i2c-core: driver [mag3110] using legacy suspend method
[    2.276258] i2c-core: driver [mag3110] using legacy resume method
[    2.282613] imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
[    2.290665] Bluetooth: Virtual HCI driver ver 1.3
[    2.295502] Bluetooth: HCI UART driver ver 2.2
[    2.299988] Bluetooth: HCI H4 protocol initialized
[    2.304782] Bluetooth: HCI BCSP protocol initialized
[    2.309761] Bluetooth: HCILL protocol initialized
[    2.314467] Bluetooth: HCIATH3K protocol initialized
[    2.319445] Bluetooth: Generic Bluetooth USB driver ver 0.6
[    2.325073] usbcore: registered new interface driver btusb
[    2.330865] sdhci: Secure Digital Host Controller Interface driver
[    2.337064] sdhci: Copyright(c) Pierre Ossman
[    2.341711] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA
[    2.348941] mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
[    2.360790] VPU initialized
[    2.364375] mxc_asrc registered
[    2.401464] Thermal calibration data is 0x55e4c269
[    2.406335] Thermal sensor with ratio = 177
[    2.425752] Anatop Thermal registered as thermal_zone0
[    2.430982] anatop_thermal_probe: default cooling device is cpufreq!
[    2.437789] usbcore: registered new interface driver usbhid
[    2.443396] usbhid: USB HID core driver
[    2.447593] usbcore: registered new interface driver snd-usb-audio
[    2.457168] mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
[    2.462524] Cirrus Logic CS42888 ALSA SoC Codec Driver
[    2.467726] usb 2-1: new high speed USB device number 2 using fsl-ehci
[    2.467749] i2c-core: driver [cs42888] using legacy suspend method
[    2.467755] i2c-core: driver [cs42888] using legacy resume method
[    2.498784] mmc0: new high speed SDHC card at address b368
[    2.515752] mmcblk0: mmc0:b368 USD   7.45 GiB
[    2.521188]  mmcblk0: p1
[    2.593753] audio_codec_ac97_cold_reset
[    2.637088] hub 2-1:1.0: USB hub found
[    2.640992] hub 2-1:1.0: 4 ports detected
[    2.678982] Found Audio codec AC97 vt1613, [ID = 5649 - 4123]
[    2.696578] asoc: vt1613 <-> imx-ssi.0 mapping ok
[    2.702192] imx_3stack asoc driver
[    2.706828] asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok
[    2.713234] ALSA device list:
[    2.716224]   #0: vt1613-audio
[    2.719280]   #1: imx-hdmi-soc
[    2.722558] NET: Registered protocol family 26
[    2.727865] TCP cubic registered
[    2.731098] NET: Registered protocol family 17
[    2.735556] can: controller area network core (rev 20090105 abi 8)
[    2.741827] NET: Registered protocol family 29
[    2.746320] can: raw protocol (rev 20090105)
[    2.750632] can: broadcast manager protocol (rev 20090105 t)
[    2.756435] Bluetooth: RFCOMM TTY layer initialized
[    2.761361] Bluetooth: RFCOMM socket layer initialized
[    2.766549] Bluetooth: RFCOMM ver 1.11
[    2.770327] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    2.775641] Bluetooth: BNEP filters: protocol multicast
[    2.780881] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    2.786905] lib80211: common routines for IEEE802.11 drivers
[    2.792569] lib80211_crypt: registered algorithm 'NULL'
[    2.792576] lib80211_crypt: registered algorithm 'WEP'
[    2.792583] lib80211_crypt: registered algorithm 'CCMP'
[    2.792589] lib80211_crypt: registered algorithm 'TKIP'
[    2.792595] Registering the dns_resolver key type
[    2.797341] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    2.805028] Registering SWP/SWPB emulation handler
[    2.810097] Bus freq driver module loaded
[    2.814111] Bus freq driver Enabled
[    2.819983] mxc_dvfs_core_probe
[    2.823226] DVFS driver module loaded
[    2.827469] registered taskstats version 1
[    2.832152] snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 01:22:06 UTC (4926)
[    2.841916] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities
[    2.896299] EXT4-fs (mmcblk0p1): couldn't mount as ext2 due to feature incompatibilities
[    2.945919] usb 2-1.3: new high speed USB device number 3 using fsl-ehci
[    2.955756] USB Host suspend begins
[    2.955764] will suspend roothub and its children
[    2.955786] ehci_fsl_bus_suspend begins, DR
[    2.956704] ehci_fsl_bus_suspend ends, DR
[    2.956720] host suspend ends
[    2.960961] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[    2.969103] VFS: Mounted root (ext4 filesystem) on device 179:1.
[    2.980018] devtmpfs: mounted
[    2.983047] Freeing init memory: 212K
[    3.111335] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[    3.112303] Registered led device: rt2800usb-phy0::radio
[    3.112363] Registered led device: rt2800usb-phy0::assoc
[    3.112434] Registered led device: rt2800usb-phy0::quality
[    4.495945] systemd[1]: systemd 212 running in system mode. (+PAM -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ +SECCOMP -APPARMOR)
[    4.496306] systemd[1]: Detected architecture 'arm'.
[    4.556145] systemd[1]: Inserted module 'autofs4'
[    4.594679] NET: Registered protocol family 10
[    4.598324] systemd[1]: Inserted module 'ipv6'
[    4.600152] systemd[1]: Set hostname to <testmachine>.
[    5.018836] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[    5.020481] systemd[1]: Expecting device dev-ttymxc1.device...
[    5.035851] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[    5.036203] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    5.036335] systemd[1]: Expecting device sys-subsystem-net-devices-eth0.device...
[    5.055829] systemd[1]: Starting Remote File Systems.
[    5.075812] systemd[1]: Reached target Remote File Systems.
[    5.075942] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[    5.076193] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    5.076319] systemd[1]: Starting Paths.
[    5.095813] systemd[1]: Reached target Paths.
[    5.095906] systemd[1]: Starting Encrypted Volumes.
[    5.115816] systemd[1]: Reached target Encrypted Volumes.
[    5.115979] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[    5.135821] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    5.135977] systemd[1]: Starting Swap.
[    5.155811] systemd[1]: Reached target Swap.
[    5.155909] systemd[1]: Starting Root Slice.
[   54.805829] systemd[1]: Created slice Root Slice.
[   54.805943] systemd[1]: Starting User and Session Slice.
[   54.825820] systemd[1]: Created slice User and Session Slice.
[   54.825933] systemd[1]: Starting Device-mapper event daemon FIFOs.
[   54.845816] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[   54.845933] systemd[1]: Starting Delayed Shutdown Socket.
[   54.865821] systemd[1]: Listening on Delayed Shutdown Socket.
[   54.865931] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[   54.885932] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[   54.886065] systemd[1]: Starting udev Kernel Socket.
[   54.905820] systemd[1]: Listening on udev Kernel Socket.
[   54.905938] systemd[1]: Starting udev Control Socket.
[   54.925847] systemd[1]: Listening on udev Control Socket.
[   54.925969] systemd[1]: Starting Journal Socket.
[   54.945848] systemd[1]: Listening on Journal Socket.
[   54.945989] systemd[1]: Starting System Slice.
[   54.965818] systemd[1]: Created slice System Slice.
[   54.965930] systemd[1]: Starting system-netctl\x2difplugd.slice.
[   54.985935] systemd[1]: Created slice system-netctl\x2difplugd.slice.
[   54.986050] systemd[1]: Starting system-getty.slice.
[   55.005817] systemd[1]: Created slice system-getty.slice.
[   55.005921] systemd[1]: Starting system-serial\x2dgetty.slice.
[   55.025825] systemd[1]: Created slice system-serial\x2dgetty.slice.
[   55.029947] systemd[1]: Started Load Kernel Modules.
[   55.030080] systemd[1]: Mounted Huge Pages File System.
[   55.030207] systemd[1]: Mounting POSIX Message Queue File System...
[   55.186392] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[   55.666241] systemd[1]: Mounted FUSE Control File System.
[   55.667808] systemd[1]: Started Set Up Additional Binary Formats.
[   55.667993] systemd[1]: Mounting Debug File System...
[   56.786111] systemd[1]: Mounted Configuration File System.
[   56.788705] systemd[1]: Starting Apply Kernel Variables...
[   57.866316] systemd[1]: Starting Setup Virtual Console...
[   58.976415] systemd[1]: Starting udev Coldplug all Devices...
[   60.096308] systemd[1]: Starting Journal Service...
[   61.245863] systemd[1]: Started Journal Service.
[   63.068238] systemd-journald[95]: Failed to register hostname fd in event loop: Operation not permitted. Ignoring.
[   70.366159] systemd-udevd[108]: starting version 212
[   70.725961] ov5640_read_reg:write reg error:reg=300a
[   70.726021] camera ov5640_mipi is not found
[   72.042980] systemd-journald[95]: Received request to flush runtime journal from PID 1
[   78.318881] eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:06, irq=-1)
[   78.318996] Activating ethernet physical layer Micrel KSZ9031 Gigabit PHY.
[   78.319968] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   81.315978] PHY: 1:06 - Link is Up - 100/Full
[   81.316791] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   91.605738] eth0: no IPv6 routers present