TP-Link Archer C2 bootlog

U-Boot 1.1.3 (Dec  4 2013 - 08:55:41)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
------------------
 Archer C2 v1.0.0
------------------
spi_wait_nsec: 29
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
============================================
Ralink UBoot Version: 4.1.2.0
--------------------------------------------
ASIC 7620_MP (Port5<->GigaSW)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Dec  4 2013  Time:08:55:41
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes

continue to starting system.
3: System Boot system code via Flash.(0xbc020000)
do_bootm:argc=2, addr=0xbc020000
## Booting image at bc020000 ...
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c150) ...
## Giving linux memsize in MB, 64

Starting kernel ...

怘�����~fx���怘�怘f�f���Linux version 2.6.36 (root@localhost.localdomain) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 Tue Apr 8 16:26:20 HKT 2014

 The CPU feqenuce set to 580 MHz

 MIPS CPU sleep mode enabled.
 PCIE: bypass PCIe DLL.
 PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
 disable all power about PCIe
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS1,115200 root=/dev/mtdblock2 rootfstype=squashfs init=/sbin/init
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00069037
Readback ErrCtl register=00069037
Memory: 61368k/65536k available (2706k kernel code, 4168k reserved, 563k data, 164k init, 0k highmem)
NR_IRQS:128
MTK/Ralink System Tick Counter init... cd:8031ff68, m:214748, s:32
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 4096 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 1ab01d
RALINK_GPIOMODE = 18b01d
PPLL_CFG1=0xe98000
MT7620 PPLL lock
PPLL_DRV =0x80080504
start PCIe register access
RALINK_PCI_PCICFG_ADDR = 1000f0

*************** MT7620 PCIe RC mode *************
bio: create slab <bio-0> at 0
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x20000000-0x200fffff]
pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff]
pci 0000:01:00.1: BAR 0: set to [mem 0x20100000-0x201fffff] (PCI address [0x20100000-0x201fffff]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [io  disabled]
pci 0000:00:00.0:   bridge window [mem 0x20000000-0x201fffff]
pci 0000:00:00.0:   bridge window [mem pref disabled]
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 20200000
res[1]->end = 2020ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20000000
res[0]->end = 200fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20100000
res[0]->end = 201fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource Ralink external timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse init (API version 7.15)
msgmni has been set to 119
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
loop: module loaded
deice id : ef 40 17 0 0 (40170000)
W25Q64BV(ef 40170000) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
Creating 7 MTD partitions on "raspi":
0x000000000000-0x000000020000 : "boot"
0x000000020000-0x000000160000 : "kernel"
0x000000160000-0x0000007c0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
0x0000007c0000-0x0000007d0000 : "config"
0x0000007d0000-0x0000007e0000 : "romfile"
0x0000007e0000-0x0000007f0000 : "rom"
0x0000007f0000-0x000000800000 : "radio"
Register flash device:flash0
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Mirror/redirect action on
u32 classifier
    Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2874 buckets, 11496 max)
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 164k freed
starting pid 173, tty '': '/etc/init.d/rcS'
rdm_major = 253
SCSI subsystem initialized
spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
Read MAC from flash(0x7DF100) ffffffe8-ffffffde-27-5f-18-26
SMACCR1 -- : 0x0000e8de
SMACCR0 -- : 0x275f1826
Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
Read MAC from flash(0x7DF100) ffffffe8-ffffffde-27-5f-18-26
SMACCR1 -- : 0x0000e8de
SMACCR0 -- : 0x275f1826
PROC INIT OK!
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
tp_domain init ok
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0

Please press Enter to activate this console. [ util_execSystem ] 135:  ipt_init cmd is "/var/tmp/dconf/rc.router"

[ dm_readFile ] 2042:  can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml
spiflash_ioctl_read, Read from 0x007c0000 length 0x10000, ret 0, retlen 0x10000
spiflash_ioctl_read, Read from 0x007c0000 length 0x10, ret 0, retlen 0x10
[ dm_loadCfg ] 2254:  software version is not match, in config, version = 271585328
[ dm_readFile ] 2042:  can not open xml file /var/tmp/pc/default_config.xml!, about to open file /etc/default_config.xml
[ parseConfigNode ] 522:  Meet unrecognized object node "PhDDNSCfg", skip the node
[ parseConfigNode ] 527:  Meet unrecognized parameter node "PhDDNSCfg", skip the node
[ parseConfigNode ] 522:  Meet unrecognized object node "SnmpCfg", skip the nodspiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
e
[ parsspiflash_ioctl_read, Read from 0x007df200 length 0x4, ret 0, retlen 0x4
eConfigNospiflash_ioctl_read, Read from 0x00020000 length 0x1d0, ret 0, retlen 0x1d0
de ] 52spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
2:  Meet unrecognized object node "ACL", skip the node
[ parseConfigNode ] 527:  Meet unrecognized parameter node "ACL", skip the node
[ parseConfigNode ] 527:  Meet unrecognized parameter node "X_TPLINK_IfName", skip the node
[ parseConfigNode ] 527:  Meet unrecognized parameter node "X_TPLINK_IfName", skip the node
[ parseConfigNode ] 522:  Meet unrecognized object node "X_TP_WANUSB3gLinkConfig", skip the node
[ parseConfigNode ] 522:  Meet unrecognized object node "QueueManagement", skip the node
[ parseConfigNode ] 522:  Meet unrecognized object node "X_TP_IPTV", skip the node
[ parseConfigNode ] 522:  Meet unrecognized object node "VoiceService", skip the node
[ parseConfigNode ] 527:  Meet unrecognized parameter node "VoiceService", skip the node
[ parseConfigNode ] 522:  Meet unrecognized object node "X_TP_SpeedDialCfg", skip the node
[ parseConfigNode ] 522:  Meet unrecognized object node "X_TP_MultiIspDialPlan", skip the node
[ parseConfigNode ] 522:  Meet unrecognized object node "X_TP_CallLogCfg", skip the node
sendto: No such file or directory
pid 250 send 2001 error
[ util_execSystem ] 135:  oal_startDynDns cmd is "dyndns /var/tmp/dconf/dyndns.conf"

[ oal_sys_getOldTZInfo ] 333:  Open TZ file error!
[ util_execSystem ] 135:  oal_sys_unsetTZ cmd is "echo "" > /etc/TZ"

[ util_execSystem ] 135:  oal_sys_unsetTZ cmd is "echo "" > /etc/TZ"

[ util_execSystem ] 135:  oal_startNoipDns cmd is "noipdns /var/tmp/dconf/noipdns.conf"

[ util_execSystem ] 135:  oal_startCmxDns cmd is "cmxdns /var/tmp/dconf/cmxdns.conf"

ioctl: No such device
[ util_execSystem ] 135:  oal_br_addBridge cmd is "brctl addbr br0;brctl setfd br0 0;brctl stp br0 off"

[ util_execSystem ] 135:  oal_ipt_addLanRules cmd is "iptables -t filter -A INPUT -i br+ -j ACCEPT
"

[ util_execSystem ] 135:  oal_intf_setIntf cmd is "ifconfig br0 192.168.0.1 netmask 255.255.255.0 up"

[ util_execSystem ] 135:  oal_util_setProcLanAddr cmd is "echo "br0 16820416," > /proc/netRaeth v3.0 (/cWorkqueueon)
ntract_Lo
phy_tx_ring = 0x030bd000, tx_ring = 0xa30bd000

phy_rx_ring0 = 0x030be000, rx_ring0 = 0xa30be000

RTL8367RB is ready now!
SMACCR1 -- : 0x0000e8de
SMACCR0 -- : 0x275f1826
caESW: Link Status Changed - Port5 Link UP
ESW: Link Status Changed - Port4 Link UP
lACDMA_CSG_CFG = 81000000
ddGDMA1_FWD_CFG = 20710000
r"

[ util_execSystem ] 135:  oal_intf_enableIntf cmd is "ifconfig eth0 up"

[ util_execSystem ] 135:  rsl_initLanEthIntfObj cmd is "vconfig add eth0 3"

[ util_execSystem ] 135:  rsl_initLanEthIntfObj cmd is "ifconfig eth0.3 up"

[ util_execSystem ] 135:  oal_br_addIntfIntoBdevice eth0.3 entered promiscuous mode
ridevice eth0 entered promiscuous mode
dgebr0: port 1(eth0.3) entering forwarding state
 cbr0: port 1(eth0.3) entering forwarding state
md is "brctl addif br0 eth0.3"

[ util_execSystem ] 135:  rsl_initLanEthIntfObj cmd is "vconfig add eth0 2"

[ util_execSystem ] 135:  rsl_initLanEthIntfObj cmd is "ifconfig eth0.2 up"

[ util_execSystem ] 135:  oal_eth_setIGMPSnoopParam cmd is "brctl setbrsnooping br0 1"

[ util_execSystem ] 135:  oal_wlan_ra_setCountryRegion cmd is "cp /etc/SingleSKU_FCC.dat /var/Wireless/RT2860AP/SingleSKU.dat"

[ util_execSystem ] 135:  oal_wlan_ra_setCountryRegion cmd is "iwpriv ra0 set CountryRegion=0"

ra0       no private ioctls.

[ util_execSystem ] 135:  oal_wlan_ra_loadDriver cmd is "insmod /lib/modules/kmdir/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko"

rt2860v2_ap: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint


=== pAd = c099c000, size = 922056 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.6_edcca_monitor_20131227
[ util_execSystem ] 135:  oal_wlan_ra_initWlan cmd is "ifconfig ra0 up"

RX DESC a3214000  size = 4096
RTMP_TimerListAdd: add timer obj c0a3ff70!
RTMP_TimerListAdd: add timer obj c0a01940!
RTMP_TimerListAdd: add timer obj c0a04194!
RTMP_TimerListAdd: add timer obj c0a04254!
RTMP_TimerListAdd: add timer obj c0a04314!
RTMP_TimerListAdd: add timer obj c0a043d4!
RTMP_TimerListAdd: add timer obj c0a04494!
RTMP_TimerListAdd: add timer obj c0a04554!
RTMP_TimerListAdd: add timer obj c0a04614!
RTMP_TimerListAdd: add timer obj c0a046d4!
RTMP_TimerListAdd: add timer obj c0a04794!
RTMP_TimerListAdd: add timer obj c0a04854!
RTMP_TimerListAdd: add timer obj c0a04914!
RTMP_TimerListAdd: add timer obj c0a049d4!
RTMP_TimerListAdd: add timer obj c0a04a94!
RTMP_TimerListAdd: add timer obj c0a04b54!
RTMP_TimerListAdd: add timer obj c0a04c14!
RTMP_TimerListAdd: add timer obj c0a04cd4!
RTMP_TimerListAdd: add timer obj c0a01914!
RTMP_TimerListAdd: add timer obj c0a04168!
RTMP_TimerListAdd: add timer obj c0a04228!
RTMP_TimerListAdd: add timer obj c0a042e8!
RTMP_TimerListAdd: add timer obj c0a043a8!
RTMP_TimerListAdd: add timer obj c0a04468!
RTMP_TimerListAdd: add timer obj c0a04528!
RTMP_TimerListAdd: add timer obj c0a045e8!
RTMP_TimerListAdd: add timer obj c0a046a8!
RTMP_TimerListAdd: add timer obj c0a04768!
RTMP_TimerListAdd: add timer obj c0a04828!
RTMP_TimerListAdd: add timer obj c0a048e8!
RTMP_TimerListAdd: add timer obj c0a049a8!
RTMP_TimerListAdd: add timer obj c0a04a68!
RTMP_TimerListAdd: add timer obj c0a04b28!
RTMP_TimerListAdd: add timer obj c0a04be8!
RTMP_TimerListAdd: add timer obj c0a04ca8!
RTMP_TimerListAdd: add timer obj c0a018e8!
RTMP_TimerListAdd: add timer obj c0a041c0!
RTMP_TimerListAdd: add timer obj c0a04280!
RTMP_TimerListAdd: add timer obj c0a04340!
RTMP_TimerListAdd: add timer obj c0a04400!
RTMP_TimerListAdd: add timer obj c0a044c0!
RTMP_TimerListAdd: add timer obj c0a04580!
RTMP_TimerListAdd: add timer obj c0a04640!
RTMP_TimerListAdd: add timer obj c0a04700!
RTMP_TimerListAdd: add timer obj c0a047c0!
RTMP_TimerListAdd: add timer obj c0a04880!
RTMP_TimerListAdd: add timer obj c0a04940!
RTMP_TimerListAdd: add timer obj c0a04a00!
RTMP_TimerListAdd: add timer obj c0a04ac0!
RTMP_TimerListAdd: add timer obj c0a04b80!
RTMP_TimerListAdd: add timer obj c0a04c40!
RTMP_TimerListAdd: add timer obj c0a04d00!
RTMP_TimerListAdd: add timer obj c09a89b0!
RTMP_TimerListAdd: add timer obj c09a85a4!
RTMP_TimerListAdd: add timer obj c09a8980!
RTMP_TimerListAdd: add timer obj c09a8d28!
RTMP_TimerListAdd: add timer obj c09a8a78!
RTMP_TimerListAdd: add timer obj c09a8aa8!
RTMP_TimerListAdd: add timer obj c09a8c68!
RTMP_TimerListAdd: add timer obj c09a8c98!
RTMP_TimerListAdd: add timer obj c09abbe8!
RTMP_TimerListAdd: add timer obj c09ab7dc!
RTMP_TimerListAdd: add timer obj c09abbb8!
RTMP_TimerListAdd: add timer obj c09abf60!
RTMP_TimerListAdd: add timer obj c09abcb0!
RTMP_TimerListAdd: add timer obj c09abce0!
RTMP_TimerListAdd: add timer obj c09abea0!
RTMP_TimerListAdd: add timer obj c09abed0!
RTMP_TimerListAdd: add timer obj c09aee20!
RTMP_TimerListAdd: add timer obj c09aea14!
RTMP_TimerListAdd: add timer obj c09aedf0!
RTMP_TimerListAdd: add timer obj c09af198!
RTMP_TimerListAdd: add timer obj c09aeee8!
RTMP_TimerListAdd: add timer obj c09aef18!
RTMP_TimerListAdd: add timer obj c09af0d8!
RTMP_TimerListAdd: add timer obj c09af108!
RTMP_TimerListAdd: add timer obj c09b2058!
RTMP_TimerListAdd: add timer obj c09b1c4c!
RTMP_TimerListAdd: add timer obj c09b2028!
RTMP_TimerListAdd: add timer obj c09b23d0!
RTMP_TimerListAdd: add timer obj c09b2120!
RTMP_TimerListAdd: add timer obj c09b2150!
RTMP_TimerListAdd: add timer obj c09b2310!
RTMP_TimerListAdd: add timer obj c09b2340!
RTMP_TimerListAdd: add timer obj c09b5290!
RTMP_TimerListAdd: add timer obj c09b4e84!
RTMP_TimerListAdd: add timer obj c09b5260!
RTMP_TimerListAdd: add timer obj c09b5608!
RTMP_TimerListAdd: add timer obj c09b5358!
RTMP_TimerListAdd: add timer obj c09b5388!
RTMP_TimerListAdd: add timer obj c09b5548!
RTMP_TimerListAdd: add timer obj c09b5578!
RTMP_TimerListAdd: add timer obj c09b84c8!
RTMP_TimerListAdd: add timer obj c09b80bc!
RTMP_TimerListAdd: add timer obj c09b8498!
RTMP_TimerListAdd: add timer obj c09b8840!
RTMP_TimerListAdd: add timer obj c09b8590!
RTMP_TimerListAdd: add timer obj c09b85c0!
RTMP_TimerListAdd: add timer obj c09b8780!
RTMP_TimerListAdd: add timer obj c09b87b0!
RTMP_TimerListAdd: add timer obj c09bb700!
RTMP_TimerListAdd: add timer obj c09bb2f4!
RTMP_TimerListAdd: add timer obj c09bb6d0!
RTMP_TimerListAdd: add timer obj c09bba78!
RTMP_TimerListAdd: add timer obj c09bb7c8!
RTMP_TimerListAdd: add timer obj c09bb7f8!
RTMP_TimerListAdd: add timer obj c09bb9b8!
RTMP_TimerListAdd: add timer obj c09bb9e8!
RTMP_TimerListAdd: add timer obj c09be938!
RTMP_TimerListAdd: add timer obj c09be52c!
RTMP_TimerListAdd: add timer obj c09be908!
RTMP_TimerListAdd: add timer obj c09becb0!
RTMP_TimerListAdd: add timer obj c09bea00!
RTMP_TimerListAdd: add timer obj c09bea30!
RTMP_TimerListAdd: add timer obj c09bebf0!
RTMP_TimerListAdd: add timer obj c09bec20!
RTMP_TimerListAdd: add timer obj c0a03d4c!
RTMP_TimerListAdd: add timer obj c0a03940!
RTMP_TimerListAdd: add timer obj c0a03d1c!
RTMP_TimerListAdd: add timer obj c0a040c4!
RTMP_TimerListAdd: add timer obj c0a03e14!
RTMP_TimerListAdd: add timer obj c0a03e44!
RTMP_TimerListAdd: add timer obj c0a03d7c!
RTMP_TimerListAdd: add timer obj c0a03dac!
RTMP_TimerListAdd: add timer obj c0a03ddc!
RTMP_TimerListAdd: add timer obj c0a168dc!
RTMP_TimerListAdd: add timer obj c0a169f8!
RTMP_TimerListAdd: add timer obj c0a16908!
RTMP_TimerListAdd: add timer obj c0a05e84!
RTMP_TimerListAdd: add timer obj c09a5e70!
RTMP_TimerListAdd: add timer obj c09a90a8!
RTMP_TimerListAdd: add timer obj c09ac2e0!
RTMP_TimerListAdd: add timer obj c09af518!
RTMP_TimerListAdd: add timer obj c09b2750!
RTMP_TimerListAdd: add timer obj c09b5988!
RTMP_TimerListAdd: add timer obj c09b8bc0!
RTMP_TimerListAdd: add timer obj c09bbdf8!
RTMP_TimerListAdd: add timer obj c0a05b94!
!!! use RTMP_RBUS_SUPPORT: AP_PROFILE_PATH_RBUS is /var/Wireless/RT2860AP/RT2860AP.dat
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
exec!
spiflash_ioctl_read, Read from 0x007f0000 length 0x200, ret 0, retlen 0x200
eeFlashId = 0x7620!
E2PROM: D0 target power=0xff1c
E2PROM: 40 MW Power Delta= 0
3. Phy Mode = 9
RTMP_TimerListAdd: add timer obj c09a5a68!
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = -1, D2 = 10, CalCode = 26 !!!
RT6352_Temperature_Init : BBPR49 = 0xffffffff
RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff5
Current Temperature from BBP_R49=0xfffffff2
RT6352_TssiTableAdjust: upper_bound = 0x7F decimal: 127
RT6352_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128
*** RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -128 -128 -128 -128 -25 -12
 - 0 - 12 28 127 127 127 127 127, offset=-11, tuning=1
RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -128 -128 -128 -128 -36 -23 - -11 - 1 17 116 116 116 116 116, offset=-11, tuning=1
mp_temperature=0xfffffffc, step = +0
E2PROM: G Tssi[-7 .. +7] = -128 -128 -128 -128 -128 -36 -23 - -11 - 1 17 116 116 116 116 116, offset=-11, tuning=1
 TX BW Filter Calibration !!!
 RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= f, phase= 2)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= 1, phase=3e)
TX IQ Calibration Done!
bAutoTxAgcG = 1
MCS Set = ff ff 00 00 01
SYNC - BBP R4 to 20MHz.l
RTMP_TimerListAdd: add timer obj c0a0619c!
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
Main bssid = e8:de:27:5f:18:26
<==== rt28xx_init, Status=0
0x1300 = 00064300
[ util_execSystem ] 135:  oal_wlan_ra_initWlan cmd is "echo 1 > /proc/tplink/led_wlan_24G"

[ util_execSystem ] 135:  oal_br_addIntfIntoBridge cmd device ra0 entered promiscuous mode
is br0: port 2(ra0) entering forwarding state
"bbr0: port 2(ra0) entering forwarding state
rctl addif br0 ra0"

[ util_execSystem ] 135:  oal_br_addIntfIntoBridge device apcli0 entered promiscuous mode
cmd is "brctl addif br0 apcli0"

[ util_execSystem ] 135:  oal_br_addIntfIntoBridge cmd is "brctl addif br0 apcli0"

brctl: bridge br0: Device or resdevice ra1 entered promiscuous mode
ource busy
[ util_execSystem ] 135:  oal_br_addIntfIntoBridge cmd is "brctl addif br0 spiflash_ioctl_read, Read from 0x007f0000 length 0x2, ret 0, retlen 0x2
ra1"

[ util_execSystem ] 135:  oal_wlan_ra_initEnd cmd is "wlNetlinkTool &"

[ util_execSystem ] 135:  oal_wlan_ra_setCountryRegion cmd is "cp /etc/SingleSKU_5G_FCC.dat /var/Wireless/RT2860AP/SingleSKU_5G.dat"

[ util_execSystem ] 135:  oal_wlan_ra_setCountryRegion cmd is "iwpriv rai0 set CountryRegionABand=0"

WLAN-Start wlNetlinkTool
Waiting for Wireless Events from interfaces...
swWlanChkAhbErr: netlink to do
rai0      no private ioctls.

[ util_execSystem ] 135:  oal_wlan_ra_loadDriver cmd is "insmod /lib/modules/kmdir/kernel/drivers/net/wireless/MT7610_ap/MT7610_ap.ko"



=== pAd = c0f82000, size = 1298408 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
device_id =0x7650
spiflash_ioctl_read, Read from 0x007f8000 length 0x200, ret 0, retlen 0x200
eeFlashId = 0x7610!
==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
MACVersion = 0x76502000
[ util_execSystem ] 135:  oal_wlan_ra_initWlan cmd is "ifconfig rai0MAC[Ver:Rev=0x76502000 : 0x76100002]
 up"

load fw spent 12ms
RX DESC a22a2000 size = 4096
RX1 DESC a22a3000 size = 4096
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
1. Phy Mode = 49
2. Phy Mode = 49
ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1
ext_pa_current_setting = 1
MT76x0_TssiTableAdjust: upper_bound = 0x7F decimal: 127
MT76x0_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128
*** MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -14 -8 -4 * 0 * 3 14 16 127 127 127 127, offset=-4, tuning=1
MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -18 -12 -8 * -4 * -1 10 12 123 123 123 123, offset=-4, tuning=1
mp_temperature=0xfffffffc, step = +0
MT76x0_TssiTableAdjust: upper_bound = 0x7F decimal: 127
MT76x0_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128
*** MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -18 -11 -6 * -4 * 4 15 20 127 127 127 127, offset=-4, tuning=1
MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -22 -15 -10 * -4 * 0 11 16 123 123 123 123, offset=-4, tuning=1
mp_temperature=0xfffffffc, step = +0
3. Phy Mode = 49
AntCfgInit: primary/secondary ant 0/1
ChipStructAssign(): RALINK6590 hook !
bAutoTxAgcG = 1
MCS Set = ff 00 00 00 01
MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
Main bssid = e8:de:27:5f:18:28
<==== rt28xx_init, Status=0
MT76x0_Calibration - Channel = 42, bPowerOn = 1, bSaveCal = 1
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
FullCalibration - Channel = 42, param = 0x301, bSave = 1, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
FullCalibration - Channel = 136, param = 0x401, bSave = 1, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
FullCalibration - Channel = 155, param = 0x501, bSave = 1, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
FullCalibration - Channel = 42, param = 0x701, bSave = 0, CalibrationMode = 255
MT76x0_Calibration - Channel = 36, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 36, param = 0x701, bSave = 0, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
MT76x0_Calibration - Channel = 40, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 40, param = 0x701, bSave = 0, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
MT76x0_Calibration - Channel = 44, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 44, param = 0x701, bSave = 0, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
MT76x0_Calibration - Channel = 48, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 48, param = 0x701, bSave = 0, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
MT76x0_Calibration - Channel = 52, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 52, param = 0x701, bSave = 0, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
MT76x0_Calibration - Channel = 56, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 56, param = 0x701, bSave = 0, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
MT76x0_Calibration - Channel = 60, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 60, param = 0x701, bSave = 0, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
MT76x0_Calibration - Channel = 64, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 64, param = 0x701, bSave = 0, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
MT76x0_Calibration - Channel = 149, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 149, param = 0x901, bSave = 0, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
MT76x0_Calibration - Channel = 153, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 153, param = 0x901, bSave = 0, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
MT76x0_Calibration - Channel = 157, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 157, param = 0x901, bSave = 0, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
MT76x0_Calibration - Channel = 161, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 161, param = 0x901, bSave = 0, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
MT76x0_Calibration - Channel = 165, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 165, param = 0x901, bSave = 0, CalibrationMode = 255
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c  28
APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
MT76x0_Calibration - Channel = 42, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 42, param = 0x701, bSave = 0, CalibrationMode = 255
0x1300 = 00064300
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
********callback func register
[ util_execSystem ] 135:  oal_wlan_ra_initWlan cmd is "echo 1 > /proc/tplink/led_wlan_5G"

[ util_execSystem ] 13device rai0 entered promiscuous mode
5: br0: port 5(rai0) entering forwarding state
 obr0: port 5(rai0) entering forwarding state
al_br_addIntfIntoBridge cmd is "brctl addif br0 rai0"

[ util_execSystem device apclii0 entered promiscuous mode
] 135:  oal_br_addIntfIntoBridge cmd is "brctl addif br0 apclii0"

[ util_execSystem ] 135:  oal_br_addIntfIntoBridge cmd is "brctl addif br0 apclii0"
device rai1 entered promiscuous mode

brctl: bridge br0: Device or resource busy
[spiflash_ioctl_read, Read from 0x007f8000 length 0x2, ret 0, retlen 0x2
 util_execSystem ] 135:  oal_br_addIntfIntoBridge cmd is "brctl addif br0 rai1"

wlNetlinkTool is already there.
sendto: No such file or directory
pid 250 send 2030 error
sendto: No such file or directory
pid 250 send 2004 error
[ util_execSystem ] 135:  oal_startDhcps cmd is "dhcpd /var/tmp/dconf/udhcpd.conf"

[ util_execSystem ] 135:  oal_lan6_startRadvd cmd is "radvd -C /var/tmp/dconf/radvd_br0.conf -p /var/run/radvd_br0.pid &"

[ util_execSystem ] 135:  oal_br_delIntfFromBridge cmd is "brctl delif br0 eth0.2"

brctl: bridge br0: Invalid argument
[ util_execSystem ] 135:  oal_intf_setIfMac cmd is "ifconfig eth0.2 down"

[ util_execSystem ] 135:  oal_intf_setIfMac cmd is "ifconfig eth0.2 hw ether E8:DE:27:5F:18:27 up"

[ util_execSystem ] 135:  oal_intf_enableIntf cmd is "ifconfig eth0.2 up"

radvd starting
iptables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135:  oal_intf_enableIntf cmd is "ifconfig eth0.2 up"

[ util_execSystem ] 135:  oal_wan6_startDhcp6c cmd is "dhcp6c -c /var/tmp/dconf/dhcp6c_eth0.2.conf -p /var/run/dhcp6c_eth0.2.pid eth0.2 eth0.2 &"

[ util_execSystem ] 135:  oal_wan6_enableAcceptRa cmd is "echo 2 > /proc/sys/net/ipv6/conf/eth0.2/accept_ra"

[ util_execSystem ] 135:  oal_wan6_enableAcceptRa cmd is "echo 0 > /proc/sys/net/ipv6/conf/eth0.2/autoconf"

[ util_execSystem ] 135:  oal_rip_updateConfig cmd is "rm -f /var/tmp/dconf/zebra.conf"

[ util_execSystem ] 135:  oal_rip_updateConfig cmd is "rm -f /var/tmp/dconf/ripd.conf"

[ util_execSystem ] 135:  removeAllRIPIpTableRule cmd is "iptables -L INPUT -v --line-numbers > /var/iptable"

[ getPidFromPidFile ] 112:  Cann't open file: /var/run/zebra.pid.
[ util_execSystem ] 135:  controlRipProcess cmd is "zebra -d -f /var/tmp/dconf/zebra.conf"

[ getPidFromPidFile ] 112:  Cann't open file: /var/run/ripd.pid.
[ util_execSystem ] 135:  oal_ipt_setDDoSRules cmd is "iptables -F FIREWALL_DDOS"

[ util_execSystem ] 135:  ddos_clearAll cmd is "rm -f /var/tmp/dosHost"

[ util_execSystem ] 135:  oal_initFirewallObj cmd is "ebtables -N FIREWALL"

[ util_execSystem ] 135:  oal_initIp6FirewallObj cmd is "ip6tables -F"

[ util_execSystem ] 135:  oal_initIp6FirewallObj cmd is "ip6tables -X"

[ util_execSystem ] 135:  oal_initIp6FirewallObj cmd is "ip6tables -P INPUT ACCEPT"

[ util_execSystem ] 135:  oal_initIp6FirewallObj cmd is "ip6tables -P FORWARD DROP"

[ util_execSystem ] 135:  oal_initIp6FirewallObj cmd is "ip6tables -P OUTPUT ACCEPT"

[ util_execSystem ] 135:  oal_initIp6FirewallObj cmd is "ip6tables -N FIREWALL"

[ util_execSystem ] 135:  oal_initIp6FirewallObj cmd is "ip6tables -N FWRULE"

[ util_execSystem ] 135:  oal_initIp6FirewallObj cmd is "ip6tables -A INPUT -i lo -p ALL -j ACCEPT -m comment   --comment "loop back""

[ util_execSystem ] 135:  oal_initIp6FirewallObj cmd is "ip6tables -A INPUT  -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT"

[ util_execSystem ] 135:  oal_initIp6FirewallObj cmd is "ip6tables -A FORWARD -i br+ -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT"

[ util_execSystem ] 135:  oal_initIp6FirewallObj cmd is "ip6tables -A FORWARD -o br+ -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT"

[ util_execSystem ] 135:  oal_initIp6FirewallObj cmd is "ip6tables -A FORWARD -j FIREWALL"

[ util_execSystem ] 135:  oal_fw6_setFwEnabeld cmd is "ip6tables -D FIREWALL -j ACCEPT"

ip6tables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135:  oal_fw6_setFwEnabeld cmd is "ip6tables -F FIREWALL"

[ util_execSystem ] 135:  oal_fw6_setFwEnabeld cmd is "ip6tables -A FIREWALL -j ACCEPT"

[ rsl_setStorageServiceObj ] 1024:  mountFlag is 3,We start usb server

[ util_execSystem ] 135:  oal_killDlnaMediaSeverProcess cmd is "killall ushare"

killall: ushare: no process killed
uShare (version 1.1a), a lightweight UPnP A/V and DLNA Media Server.
Benjamin Zores (C) 2005-2007, for GeeXboX Team.
See http://ushare.geexbox.org/ for updates.
[ util_execSystem ] 135:  oal_ipt_setWanPort cmd is "iptables -t filter -D INPUT -p tcp --dport 21 -j ACCEPT"

iptables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135:  oal_ipt_setWanPort cmd is "iptables -t nat -D PREROUTING -p tcp --dport 21 -j ACCEPT"

iptables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135:  oal_startPrintSrv cmd is "insmod /lib/modules/GPL_NetUSB.ko"

kcg 323 :GPL NetUSB up!
[ util_execSystem ] 135:  oal_startPrintSrv cmd is "insmod /lib/modules/NetUSB.ko"

kc   90 : run_telnetDBGDServer start
kc  227 : init_DebugD end
INFO17F1: NetUSB 1.02.47, 00020624 : Dec 16 2013 11:39:50
INFO17F3:  AUTH ISOC
INFO17F4:  filterAudio
usbcore: registered new interface driver KC NetUSB General Driver
INFO013F:  init proc : PAGE_SIZE 4096
INFO16C5:  infomap c115d750
INFO16C8:  sleep to wait br0 to wake up
INFO02D0:  use dev Name br0
INFO16D1:  sleep to wait br0 end.
INFO16EA:  UDP_BROAD 7437 tcpPort:20005
INFO02D0:  use dev Name br0
[ util_execSystem ] 135:  setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_ftp.ko"

INFO15D1: tcpConnector() started...
[ util_execSystem ] 135:  setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_ftp.ko"

[ util_execSystem ] 135:  oal_openAlg cmd is "iptables -D FORWARD_VPN_PASSTHROUGH  -p udp --dport 500 -j DROP"

iptables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135:  setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko"

[ util_execSystem ] 135:  setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_pptp.ko"

[ util_execSystem ] 135:  oal_openAlg cmd is "iptables -D FORWARD_VPN_PASSTHROUGH  -p tcp --dport 1723 -j DROP"

iptables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135:  oal_openAlg cmd is "iptables -D FORWARD_VPN_PASSTHROUGH  -p udp --dport 1701 -j DROP"

iptables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135:  setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_tftp.ko"

[ util_execSystem ] 135:  setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_tftp.ko"

[ util_execSystem ] 135:  setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_h323.ko"

[ util_execSystem ] 135:  setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_h323.ko"

[ util_execSystem ] 135:  setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_sip.ko"

[ util_execSystem ] 135:  setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_sip.ko"

[ util_execSystem ] 135:  setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_rtsp.ko"

nf_conntrack_rtsp v0.6.21 loading
[ util_execSystem ] 135:  setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_rtsp.ko"

nf_nat_rtsp v0.6.21 loading
[ util_execSystem ] 135:  oal_wan_HWNat_enable cmd is "insmod /lib/modules/kmdir/kernel/net/nat/hw_nat/hw_nat.ko"

Ralink HW NAT Module Enabled
=============== ACL Value =========
REG_ESW_VLAN_VTCR value is 0x80004000

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80004001

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80004002

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80004003

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80004004

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80004005

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80004006

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80004007

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80004008

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80004009

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000400a

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000400b

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80008000

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000a000

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80008001

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000a001

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80008002

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000a002

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80008003

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000a003

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80008004

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000a004

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80008005

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000a005

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80008006

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000a006

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80008007

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000a007

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80008008

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000a008

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x80008009

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000a009

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000800a

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000a00a

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000800b

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
REG_ESW_VLAN_VTCR value is 0x8000a00b

REG_ESW_VLAN_VAWD1 value is 0x0
REG_ESW_VLAN_VAWD2 value is 0x0
============ ACL Value End=========
INFO14AE: Bind to br0
[ util_execSystem ] 135:  oal_sys_unsetTZ cmd is "echo "" > /etc/TZ"

[ util_execSystem ] 135:  oal_sys_unsetTZ cmd is "echo "" > /etc/TZ"