Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 1.1.4 (Dec 22 2015 - 12:54:58)
- DB120
- DRAM:
- sri
- Wasp 1.2
- wasp_ddr_initial_config(249): (32bit) ddr2 init
- wasp_ddr_initial_config(426): Wasp ddr init done
- Tap value selected = 0xf [0x0 - 0x1f]
- 128 MB
- Top of RAM usable for U-Boot at: 88000000
- Reserving 276k for U-Boot at: 87fb8000
- Reserving 192k for malloc() at: 87f88000
- Reserving 44 Bytes for Board Info at: 87f87fd4
- Reserving 36 Bytes for Global Data at: 87f87fb0
- Reserving 128k for boot params() at: 87f67fb0
- Stack Pointer at: 87f67f98
- Now running in RAM - U-Boot at: 87fb8000
- Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x14
- flash size 1MB, sector count = 16
- Flash: 1 MB
- *** Warning - bad CRC, using default environment
- Now starting pci_init process
- pci_init_board: PCIe PLL not set for 40MHz refclk
- BOARD IS NOT CALIBRATED!!!
- pci_init finished
- In: serial
- Out: serial
- Err: serial
- Net: ag934x_enet_initialize...
- No valid address in Flash. Using fixed address
- No valid address in Flash. Using fixed address
- wasp reset mask:c02200
- WASP ----> S27 PHY
- s27 reg init
- : cfg1 0x80000000 cfg2 0x7114
- eth0: 00:03:7f:09:0b:ad
- athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
- eth0 up
- WASP ----> S27 PHY
- s27 reg init lan
- ATHRS27: resetting s27
- ATHRS27: s27 reset done
- : cfg1 0x800c0000 cfg2 0x7214
- eth1: 00:03:7f:09:0b:ad
- athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
- athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
- athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
- athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
- athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
- eth1 up
- eth0, eth1
- Atheros on-chip NAND FLash Controller Driver, Version 0.1 (c) 2010 Atheros Communications, Ltd.
- Ath Nand ID[87fef17c]: 2c:48:00:26:89
- ONFI MICRON MT29F16G08ABABAWP
- Micronset ns -0x80000-0x1000
- ====== NAND Parameters ======
- sc = 0x87fef158 bbt = 0x87f98538 bbt_size = 0x400 nf_ctrl = 0x485
- page = 0x1000 block = 0x80000 oob = 0xe0
- size = 2048MB
- Setting 0xb8116290 to 0x20402d0f
- Hit any key to stop autoboot: 0
- Loading from device 0: ath-nand (offset 0x0)
- ** Bad Magic Number 0x73797375 **
- uboot>
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement