API tools faq
paste
Advertisement
Guest User

wdr7500 boot

a guest
May 14th, 2013
1,860
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 21.82 KB | None | 0 0
raw download clone embed print report
  1. U-Boot 1.1.4 (Jan 26 2013 - 13:35:40)
  2.  
  3. ap135 - Scorpion 1.0DRAM:
  4. sri
  5. Scorpion 1.0
  6. ath_ddr_initial_config(178): (32bit) ddr2 init
  7. tap = 0x00000003
  8. Tap (low, high) = (0x3, 0x1f)
  9. Tap values = (0x11, 0x11, 0x11, 0x11)
  10. 128 MB
  11. Flash Manuf Id 0x1c, DeviceId0 0x30, DeviceId1 0x17
  12. flash size 8MB, sector count = 128
  13. Flash: 8 MB
  14. Using default environment
  15.  
  16. *** Warning *** : PCIe WLAN Module not found !!!
  17. In: serial
  18. Out: serial
  19. Err: serial
  20. Net: ath_gmac_enet_initialize...
  21. athrs_sgmii_res_cal: cal value = 0xe
  22. No valid address in Flash. Using fixed address
  23. No valid address in Flash. Using fixed address
  24. ath_gmac_enet_initialize: reset mask:c02200
  25. Scorpion ----> S17 PHY *
  26. Vlan config...
  27. TEST: FINAL REG VAL after TX Calibration - 0x46000000
  28. TEST: FINAL XMII VAL after RX Calibration - 0x56000000
  29. TEST: FINAL ETH_CFG VAL after RX Calibration - 0x00028001
  30. athrs17_reg_init: complete
  31. : cfg1 0x80000000 cfg2 0x7335
  32. eth0: ba:be:fa:ce:08:41
  33. eth0 up
  34. athrs17_reg_init_wan done
  35. SGMII in forced mode
  36. athr_gmac_sgmii_setup SGMII done
  37. : cfg1 0x800c0000 cfg2 0x7214
  38. eth1: ba:be:fa:ce:08:41
  39. eth1 up
  40. eth0, eth1
  41. Setting 0x18116290 to 0x54a9214f
  42. Autobooting in 1 seconds
  43. ## Booting image at 9f020000 ...
  44. Uncompressing Kernel Image ... OK
  45.  
  46. Starting kernel ...
  47.  
  48. Booting QCA955x
  49. \00
  50. Linux version 2.6.31--LSDK-9.2.0_U6.616 (root@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #1 Sat Jan 26 13:40:17 CST 2013
  51. Ram size passed from bootloader =128M
  52. flash_size passed from bootloader = 8
  53. CPU revision is: 00019750 (MIPS 74Kc)
  54. cpu apb ddr apb ath_sys_frequency: cpu 720 ddr 600 ahb 200
  55. Determined physical RAM map:
  56. memory: 08000000 @ 00000000 (usable)
  57. Zone PFN ranges:
  58. Normal 0x00000000 -> 0x00008000
  59. Movable zone start PFN for each node
  60. early_node_map[1] active PFN ranges
  61. 0: 0x00000000 -> 0x00008000
  62. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
  63. Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6912k(rootfs),64k(config),64k(ART) mem=128M
  64. PID hash table entries: 512 (order: 9, 2048 bytes)
  65. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  66. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  67. Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  68. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  69. Writing ErrCtl register=00000000
  70. Readback ErrCtl register=00000000
  71. Memory: 112868k/131072k available (1889k kernel code, 18028k reserved, 435k data, 120k init, 0k highmem)
  72. NR_IRQS:128
  73. plat_time_init: plat time init done
  74. Calibrating delay loop... 359.42 BogoMIPS (lpj=718848)
  75. Mount-cache hash table entries: 512
  76.  
  77. ****************ALLOC***********************
  78. Packet mem: 802774e0 (0xe00000 bytes)
  79. ********************************************
  80.  
  81. NET: Registered protocol family 16
  82. ath_pcibios_init: bus 0
  83. ***** Warning PCIe 0 H/W not found !!!
  84. registering PCI controller with io_map_base unset
  85. ath_pcibios_init: bus 1
  86. ath_pcibios_init(232): PCI 1 CMD write: 0x356
  87. registering PCI controller with io_map_base unset
  88. Reset button pressed.
  89. bio: create slab <bio-0> at 0
  90. pcibios_map_irq: IRQ 76 for bus 1
  91. NET: Registered protocol family 2
  92. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  93. TCP established hash table entries: 4096 (order: 3, 32768 bytes)
  94. TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
  95. TCP: Hash tables configured (established 4096 bind 4096)
  96. TCP reno registered
  97. NET: Registered protocol family 1
  98. ATH GPIOC major 0
  99. squashfs: version 4.0 (2009/01/31) Phillip Lougher
  100. msgmni has been set to 220
  101. Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
  102. io scheduler noop registered
  103. io scheduler deadline registered (default)
  104. Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  105. serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
  106. console [ttyS0] enabled
  107. PPP generic driver version 2.4.2
  108. NET: Registered protocol family 24
  109. 5 cmdlinepart partitions found on MTD device ath-nor0
  110. Creating 5 MTD partitions on "ath-nor0":
  111. 0x000000000000-0x000000020000 : "u-boot"
  112. 0x000000020000-0x000000120000 : "kernel"
  113. 0x000000120000-0x0000007e0000 : "rootfs"
  114. 0x0000007e0000-0x0000007f0000 : "config"
  115. 0x0000007f0000-0x000000800000 : "ART"
  116. ->Oops: flash id 0x1c3017 .
  117. TCP cubic registered
  118. NET: Registered protocol family 10
  119. NET: Registered protocol family 17
  120. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  121. All bugs added by David S. Miller <davem@redhat.com>
  122. athwdt_init: Registering WDT success
  123. ath_otp_init: Registering OTP success
  124. VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  125. Freeing unused kernel memory: 120k freed
  126.  
  127. init started: BusyBox v1.01 (2012.11.27-00:48+0000) multi-call binary
  128. This Board use 2.6.31
  129. xt_time: kernel timezone is -0000
  130. nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
  131. CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
  132. nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
  133. sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
  134. ip_tables: (C) 2000-2006 Netfilter Core Team
  135. insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
  136. insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
  137. PPPoL2TP kernel driver, V1.0
  138. PPTP driver version 0.8.3
  139. insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
  140.  
  141. (none) mips #1 Sat Jan 26 13:40:17 CST 2013 (none)
  142.  
  143. (none) login: qca955x_GMAC: Length per segment 1536
  144. 955x_GMAC: qca955x_gmac_attach
  145. 955x_GMAC: qca955x_set_gmac_caps
  146. Currently in polling mode unit1
  147. mac:1 Registering S17....
  148. qca955x_GMAC: RX TASKLET - Pkts per Intr:200
  149. qca955x_GMAC: Max segments per packet : 1
  150. qca955x_GMAC: Max tx descriptor count : 220
  151. qca955x_GMAC: Max rx descriptor count : 220
  152. qca955x_GMAC: Mac capability flags : 12002200
  153. 955x_GMAC: qca955x_gmac_attach
  154. 955x_GMAC: qca955x_set_gmac_caps
  155. Currently in polling mode unit0
  156. mac:0 Registering S17....
  157. qca955x_GMAC: RX TASKLET - Pkts per Intr:200
  158. qca955x_GMAC: Max segments per packet : 1
  159. qca955x_GMAC: Max tx descriptor count : 220
  160. qca955x_GMAC: Max rx descriptor count : 220
  161. qca955x_GMAC: Mac capability flags : 10002A00
  162. 955x_GMAC: Serdes PLL is locked value 0x1f038116
  163. athr_gmac_ring_alloc Allocated 3520 at 0x87950000
  164. athr_gmac_ring_alloc Allocated 3520 at 0x87a8e000
  165. 955x_GMAC: eth1 in SGMII MODE
  166. Scorpion -----> S17 PHY
  167. ACL is not yet enabled. Enabling...
  168. Hello, nat helper module for 1.08!
  169. netlink_kernel_create succeeded at tp_rule_nl_prot: [29]
  170.  
  171. ######## S17 SSDK init succeeded! ########
  172. _athrs17_mac0_intf SGMII done
  173. athrs17_reg_init:done
  174. 955x_SGMII::athr_gmac_sgmii_setup Done
  175. Setting Drop CRC Errors, Pause Frames and Length Error frames
  176. Setting PHY...
  177. Phy setup Complete
  178. ADDRCONF(NETDEV_UP): eth0: link is not ready
  179. device eth0.1 entered promiscuous mode
  180. device eth0 entered promiscuous mode
  181. SET INTF MAC 0:1c-fa-68-fe-32-f4
  182. SET INTF MAC 1:1c-fa-68-fe-32-f5
  183. br0: port 1(eth0.1) entering forwarding state
  184. nf_conntrack_rtsp v0.6.21 loading
  185. nf_nat_rtsp v0.6.21 loading
  186. adf: module license 'Proprietary' taints kernel.
  187. Disabling lock debugging due to kernel taint
  188. ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
  189. ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
  190. ath_dfs: Version 2.0.0
  191. Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
  192. ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
  193. ath_ahb: 10.0.107 (Atheros/multi-bss)
  194. check DDR Activity - HIGH
  195. ar9300_set_reset: Scorpion SoC RTC reset done.
  196. Enterprise mode: 0x43fc0000
  197. Restoring Cal data from Flash
  198. check DDR Activity - HIGH
  199. ar9300_set_reset: Scorpion SoC RTC reset done.
  200. ath_get_caps[5863] rx chainmask mismatch actual 7 sc_chainmak 0
  201. ath_get_caps[5838] tx chainmask mismatch actual 7 sc_chainmak 0
  202. check DDR Activity - HIGH
  203. ar9300_set_reset: Scorpion SoC RTC reset done.
  204. check DDR Activity - HIGH
  205. ar9300_set_reset: Scorpion SoC RTC reset done.
  206. check DDR Activity - HIGH
  207. ar9300_set_reset: Scorpion SoC RTC reset done.
  208. SC Callback Registration for wifi0
  209. wifi0: Atheros ???: mem=0xb8100000, irq=2
  210. ath_pci: 10.0.107 (Atheros/multi-bss)
  211. ath_pci_probe
  212. ath_pci 0000:01:00.0: ath DEBUG: sc=0x87aa7ce0
  213.  
  214. ol_ath_pci_configure : num_desired MSI set to 0
  215.  
  216. Using PCI Legacy Interrupt
  217. __ol_ath_attach: ath_attach TODO
  218. ol_ath_attach() BMI inited.
  219. ol_ath_attach() BMI Get Target Info.
  220. ol_ath_attach() TARGET TYPE: 7 Vers 0x4000002c
  221. NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
  222. ol_ath_attach() configure Target .
  223. ol_transfer_bin_file: flash cal data len 65535 doesn't equal to 2116
  224. ol_transfer_bin_file: Board data file AR9888v1
  225. ol_transfer_bin_file 1535: Download Board data len 2116
  226. ol_ath_download_firmware: Using 0x1234 for the remainder of init
  227. ol_transfer_bin_file 1527: Download OTP data len 3572
  228. ol_transfer_bin_file 1553: Download Firmware data len 183920
  229. ol_ath_attach() Download FW.
  230. ol_ath_attach() HT Create .
  231. ol_ath_attach() HIF Claim.
  232. ol_ath_attach() BMI Done.
  233. ol_ath_attach() WMI attached. wmi_handle 86ce0000
  234. +HWT
  235. -HWT
  236. HTC Service:0x0300 ep:1 TX flow control disabled
  237. TXRX: Created pdev 86df3a00
  238. wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event
  239. num_rf_chain : 00000003
  240. ht_cap_info: : 0000085b
  241. vht_cap_info : 338001b2
  242. vht_supp_mcs : 0000ffea
  243. wmi_ready_event_rx: WMI UNIFIED READY event
  244. ol_ath_connect_htc() WMI is ready
  245. ol_ath_set_host_app_area TODO
  246. ol_ath_attach() connect HTC.
  247. target uses HTT version 2.0; host uses 2.0
  248. ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
  249. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
  250. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
  251. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
  252. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
  253. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
  254. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
  255. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
  256. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
  257. ol_ath_phyerr_attach: called
  258. OL Resmgr Init-ed
  259. ol_if_dfs_setup: called
  260. ol_if_dfs_attach: called; ptr=87af3974, radar_info=87addb98
  261. ol_ath_rtt_meas_report_attach: called
  262. ol_ath_attach() UMAC attach .
  263. __ol_ath_attach: init tx/rx TODO
  264. __ol_ath_attach: hard_header_len reservation 58
  265. __ol_ath_attach: dev name wifi1
  266. SC Callback Registration for wifi1
  267. check DDR Activity - HIGH
  268. ar9300_set_reset: Scorpion SoC RTC reset done.
  269. check DDR Activity - HIGH
  270. ar9300_set_reset: Scorpion SoC RTC reset done.
  271. check DDR Activity - HIGH
  272. ar9300_set_reset: Scorpion SoC RTC reset done.
  273. VAP device ath0 created
  274.  
  275. DES SSID SET=<redacted>
  276. ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
  277. check DDR Activity - HIGH
  278. ar9300_set_reset: Scorpion SoC RTC reset done.
  279. check DDR Activity - HIGH
  280. ar9300_set_reset: Scorpion SoC RTC reset done.
  281. check DDR Activity - HIGH
  282. ar9300_set_reset: Scorpion SoC RTC reset done.
  283. Invoking ACS module for Best channel selection
  284. check DDR Activity - HIGH
  285. ar9300_set_reset: Scorpion SoC RTC reset done.
  286. check DDR Activity - HIGH
  287. ar9300_set_reset: Scorpion SoC RTC reset done.
  288. check DDR Activity - HIGH
  289. ar9300_set_reset: Scorpion SoC RTC reset done.
  290. check DDR Activity - HIGH
  291. ar9300_set_reset: Scorpion SoC RTC reset done.
  292. Channel 1 average beacon RSSI 25 noisefloor -107 ieee80211_acs_find_best_11ng_centerchan chan: 1 beacon RSSI + weighted noisefloor: -189
  293. Channel 6 average beacon RSSI 8 noisefloor -107 ieee80211_acs_find_best_11ng_centerchan chan: 6 beacon RSSI + weighted noisefloor: -206
  294. Channel 6 average beacon RSSI 8 noisefloor -107 ieee80211_acs_find_best_11ng_centerchan chan: 6 beacon RSSI + weighted noisefloor: -206
  295. Channel 11 average beacon RSSI 9 noisefloor -107 ieee80211_acs_find_best_11ng_centerchan chan: 11 beacon RSSI + weighted noisefloor: -205
  296. ieee80211_acs_find_best_11ng_centerchan found best 11ng center chan: 6 rssi: -206
  297. check DDR Activity - HIGH
  298. ar9300_set_reset: Scorpion SoC RTC reset done.
  299. check DDR Activity - HIGH
  300. ar9300_set_reset: Scorpion SoC RTC reset done.
  301. check DDR Activity - HIGH
  302. ar9300_set_reset: Scorpion SoC RTC reset done.
  303. ieee80211_dfs_cac_start[267] ===NON DFS chan === 2437
  304. check DDR Activity - HIGH
  305. ar9300_set_reset: Scorpion SoC RTC reset done.
  306. check DDR Activity - HIGH
  307. ar9300_set_reset: Scorpion SoC RTC reset done.
  308. check DDR Activity - HIGH
  309. ar9300_set_reset: Scorpion SoC RTC reset done.
  310. check DDR Activity - HIGH
  311. ar9300_set_reset: Scorpion SoC RTC reset done.
  312. check DDR Activity - HIGH
  313. ar9300_set_reset: Scorpion SoC RTC reset done.
  314. ieee80211_dfs_cac_start[267] ===NON DFS chan === 2437
  315. check DDR Activity - HIGH
  316. ar9300_set_reset: Scorpion SoC RTC reset done.
  317. check DDR Activity - HIGH
  318. ar9300_set_reset: Scorpion SoC RTC reset done.
  319. check DDR Activity - HIGH
  320. ar9300_set_reset: Scorpion SoC RTC reset done.
  321. athr_gmac_ring_alloc Allocated 3520 at 0x86dfd000
  322. athr_gmac_ring_alloc Allocated 3520 at 0x87ae4000
  323. 955x_GMAC: eth0 in RGMII MODE
  324. Scorpion -----> S17 PHY
  325. athrs17_reg_init_wan done
  326. Setting Drop CRC Errors, Pause Frames and Length Error frames
  327. Setting PHY...
  328. ADDRCONF(NETDEV_UP): eth1: link is not ready
  329. device eth1 entered promiscuous mode
  330. check DDR Activity - HIGH
  331. ar9300_set_reset: Scorpion SoC RTC reset done.
  332. check DDR Activity - HIGH
  333. ar9300_set_reset: Scorpion SoC RTC reset done.
  334. check DDR Activity - HIGH
  335. ar9300_set_reset: Scorpion SoC RTC reset done.
  336. ieee80211_dfs_cac_start[267] ===NON DFS chan === 2437
  337. device ath0 entered promiscuous mode
  338. br1: port 2(ath0) entering forwarding state
  339. ieee80211_ioctl_siwmode: imr.ifm_active=918144, new mode=3, valid=1
  340. check DDR Activity - HIGH
  341. ar9300_set_reset: Scorpion SoC RTC reset done.
  342. check DDR Activity - HIGH
  343. ar9300_set_reset: Scorpion SoC RTC reset done.
  344. br1: port 2(ath0) entering disabled state
  345. DEVICE IS DOWN ifname=ath0
  346. DEVICE IS DOWN ifname=ath0
  347. check DDR Activity - HIGH
  348. ar9300_set_reset: Scorpion SoC RTC reset done.
  349. check DDR Activity - HIGH
  350. ar9300_set_reset: Scorpion SoC RTC reset done.
  351. check DDR Activity - HIGH
  352. ar9300_set_reset: Scorpion SoC RTC reset done.
  353. check DDR Activity - HIGH
  354. ar9300_set_reset: Scorpion SoC RTC reset done.
  355. ieee80211_dfs_cac_start[267] ===NON DFS chan === 2437
  356. br1: port 2(ath0) entering forwarding state
  357. check DDR Activity - HIGH
  358. ar9300_set_reset: Scorpion SoC RTC reset done.
  359. check DDR Activity - HIGH
  360. ar9300_set_reset: Scorpion SoC RTC reset done.
  361. br1: port 2(ath0) entering disabled state
  362. br1: starting userspace STP failed, starting kernel STP
  363. check DDR Activity - HIGH
  364. ar9300_set_reset: Scorpion SoC RTC reset done.
  365. check DDR Activity - HIGH
  366. ar9300_set_reset: Scorpion SoC RTC reset done.
  367. check DDR Activity - HIGH
  368. ar9300_set_reset: Scorpion SoC RTC reset done.
  369. ieee80211_dfs_cac_start[267] ===NON DFS chan === 2437
  370. br1: topology change detected, propagating
  371. br1: port 2(ath0) entering forwarding state
  372. isCountryCodeValid: EEPROM regdomain 0x52
  373. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
  374. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
  375. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
  376. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
  377. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
  378. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
  379. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
  380. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
  381. ath_ioctl: SIOC80211IFCREATE CALLED
  382. wmi_unified_vdev_create_send: ID = 0 VAP Addr = 1c:fa:68:fe:32:f2:
  383. TXRX: Created vdev 86f6ee00 (1c:fa:68:fe:32:f2)
  384. VAP device ath1 created
  385. TXRX: ol_txrx_peer_find_add_id: peer 86f60400 ID 129
  386. TXRX: ol_txrx_peer_find_add_id: peer 86f60400 ID 145
  387. Setting vdev param = f, value = 1
  388. ol_ath_vap_set_param: VAP param unsupported param:80 value:1
  389. ol_ath_vap_set_param: VAP param unsupported param:35 value:0
  390.  
  391. DES SSID SET=<redacted>
  392. ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
  393. OL vap_stop +
  394. wmi_unified_vdev_stop_send
  395. OL vap_stop -
  396. STOPPED EVENT for vap 0
  397. Setting vdev param = 1a, value = 1
  398. Setting vdev param = 3, value = 100
  399. Setting vdev param = d, value = 1
  400. Setting vdev param = 12, value = 1
  401. Setting vdev param = 1e, value = 1
  402. OL vap_stop +
  403. wmi_unified_vdev_stop_send
  404. OL vap_stop -
  405. STOPPED EVENT for vap 0
  406. OL vap_start +
  407. OL vap_start -
  408. ol_vdev_start_resp_ev
  409. ol_ath_vap_join: join operation is only for STA/IBSS mode
  410. set channel freq 5745
  411. WMI channel freq=5745, mode=a band_center_freq1=5775
  412. ol_if_dfs_configure: called
  413. ol_if_dfs_disable: called
  414. ol_ath_wmm_update:
  415. ieee80211_dfs_cac_start[267] ===NON DFS chan === 5745
  416. Setting vdev param = 3, value = 100
  417. Notification to UMAC VAP layer
  418. FIRMWARE:75 C ,5401 M 1f 5775 2f 9744 408
  419. device ath1 entered promiscuous mode
  420. br1: topology change detected, propagating
  421. br1: port 3(ath1) entering forwarding state
  422. ieee80211_ioctl_siwmode: imr.ifm_active=131738, new mode=3, valid=1
  423. wmi_unified_vdev_stop_send
  424. STOPPED EVENT for vap 0
  425. br1: port 3(ath1) entering disabled state
  426. ol_ath_vap_set_param: VAP param unsupported param:32 value:0
  427. ol_ath_vap_set_param: VAP param unsupported param:121 value:1
  428. DEVICE IS DOWN ifname=ath1
  429. DEVICE IS DOWN ifname=ath1
  430. ol_ath_vap_set_param: VAP param unsupported param:32 value:0
  431. ol_ath_vap_set_param: VAP param unsupported param:32 value:0
  432. ol_ath_vap_set_param: VAP param unsupported param:32 value:1
  433. ol_ath_vap_set_param: VAP param unsupported param:74 value:1
  434. Group Keyidx set=1
  435. wmi_unified_vdev_install_key_send Setting Key for Macaddress:0xf232fe68fa1c
  436. Keyix=1 Keylen=16 Keyflags=1 Cipher=4
  437. Keydata=0x71 0xdd 0x9c 0x85 0x11 0x96 0x2a 0xd5 0x2d 0x82 0xfa 0xac 0x1a 0x96 0xa7 0x3d
  438. ol_ath_vap_set_param: VAP param unsupported param:74 value:0
  439. TXRX: ol_txrx_peer_find_add_id: peer 86f60400 ID 114
  440. TXRX: sec spec for peer 86f60400 (1c:fa:68:fe:32:f2): mcast key of type 6
  441. Setting vdev param = 1f, value = 1
  442. OL vap_stop +
  443. wmi_unified_vdev_stop_send
  444. OL vap_stop -
  445. STOPPED EVENT for vap 0
  446. OL vap_start +
  447. OL vap_start -
  448. ol_vdev_start_resp_ev
  449. ol_ath_vap_join: join operation is only for STA/IBSS mode
  450. set channel freq 5745
  451. WMI channel freq=5745, mode=a band_center_freq1=5775
  452. ol_if_dfs_configure: called
  453. ol_if_dfs_disable: called
  454. ol_ath_wmm_update:
  455. ieee80211_dfs_cac_start[267] ===NON DFS chan === 5745
  456. Setting vdev param = 3, value = 100
  457. Notification to UMAC VAP layer
  458. FIRMWARE:75 C ,5401 M 1f 5775 2f 8624 238
  459. br1: topology change detected, propagating
  460. br1: port 3(ath1) entering forwarding state
  461. FWLOG: [32170] WAL_DBGID_SECURITY_ENCR_EN ( )
  462. FWLOG: [32170] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
  463. wmi_unified_vdev_stop_send
  464. STOPPED EVENT for vap 0
  465. br1: port 3(ath1) entering disabled state
  466. OL vap_stop +
  467. wmi_unified_vdev_stop_send
  468. OL vap_stop -
  469. STOPPED EVENT for vap 0
  470. OL vap_start +
  471. OL vap_start -
  472. ol_vdev_start_resp_ev
  473. ol_ath_vap_join: join operation is only for STA/IBSS mode
  474. set channel freq 5745
  475. WMI channel freq=5745, mode=a band_center_freq1=5775
  476. ol_if_dfs_configure: called
  477. ol_if_dfs_disable: called
  478. ol_ath_wmm_update:
  479. ieee80211_dfs_cac_start[267] ===NON DFS chan === 5745
  480. Setting vdev param = 3, value = 100
  481. Notification to UMAC VAP layer
  482. FIRMWARE:75 C ,5401 M 1f 5775 2f 8624 238
  483. br1: topology change detected, propagating
  484. br1: port 3(ath1) entering forwarding state
  485. fuse init (API version 7.12)
  486. usbcore: registered new interface driver usbfs
  487. usbcore: registered new interface driver hub
  488. usbcore: registered new device driver usb
  489. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  490. Port Status 1c000004
  491. ath-ehci ath-ehci.0: ATH EHCI
  492. ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
  493. ehci_reset Intialize USB CONTROLLER in host mode: 13
  494. ehci_reset Port Status 1c000000
  495. ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
  496. ehci_reset Intialize USB CONTROLLER in host mode: 13
  497. ehci_reset Port Status 1c000000
  498. ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
  499. usb usb1: configuration #1 chosen from 1 choice
  500. hub 1-0:1.0: USB hub found
  501. hub 1-0:1.0: 1 port detected
  502. Port Status 1c000000
  503. ath-ehci1 ath-ehci1.1: ATH EHCI
  504. ath-ehci1 ath-ehci1.1: new USB bus registered, assigned bus number 2
  505. ehci_reset Intialize USB CONTROLLER in host mode: 13
  506. ehci_reset Port Status 1c000000
  507. ath-ehci1 ath-ehci1.1: irq 3, io mem 0x1b400000
  508. ehci_reset Intialize USB CONTROLLER in host mode: 13
  509. ehci_reset Port Status 1c000000
  510. ath-ehci1 ath-ehci1.1: USB 2.0 started, EHCI 1.00
  511. usb usb2: configuration #1 chosen from 1 choice
  512. hub 2-0:1.0: USB hub found
  513. hub 2-0:1.0: 1 port detected
  514. SCSI subsystem initialized
  515. Initializing USB Mass Storage driver...
  516. usbcore: registered new interface driver usb-storage
  517. USB Mass Storage support registered.
  518. GPL NetUSB up!
  519. kc 86 : run_telnetDBGDServer start
  520. kc 223 : init_DebugD end
  521. INFO1758: NetUSB 1.184, 0002061F : May 7 2012 10:35:23
  522. INFO175A: AUTH ISOC
  523. INFO175B:
  524. usbcore: registered new interface driver KC NetUSB General Driver
  525. INFO0076: init proc : PAGE_SIZE 4096
  526. INFO17B4: Check mac address
  527. INFO162C: infomap 8668c220
  528. INFO162F: sleep to wait br0 to wake up
  529. INFO02D0: use dev Name br0
  530. INFO1638: sleep to wait br0 end.
  531. INFO1651: UDP_BROAD 7437 tcpPort:625868800
  532. INFO02D0: use dev Name br0
  533. INFO1538: tcpConnector() started...
  534. 955x_GMAC: qca955x_soc_gmac_set_mac_duplex
  535. 955x_GMAC: qca955x_soc_gmac_set_link Done
  536. ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
  537. br1: topology change detected, propagating
  538. br1: port 1(eth1) entering forwarding state
  539.  
  540. Enet:1 port1 up
  541. 955x_GMAC: enet unit:1 is up...
  542. eth1 SGMII 1000Mbps full duplex
  543. 955x_GMAC: qca955x_soc_gmac_set_mac_duplex
  544. 955x_GMAC: qca955x_soc_gmac_set_link Done
  545. 955x_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
  546. ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  547. INFO1415: Bind to br0
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!