Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- [ 0.000000] Linux version 3.7.10 (noltari@skynet) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Sun Mar 24 14:47:25 CET 2013
- [ 0.000000] Detected Broadcom 0x6328 CPU revision 10b0
- [ 0.000000] CPU frequency is 320 MHz
- [ 0.000000] 64MB of RAM installed
- [ 0.000000] registering 32 GPIOs
- [ 0.000000] board_bcm963xx: Boot address 0xb8000000
- [ 0.000000] board_bcm963xx: CFE version: 1.0.37-106.5
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
- [ 0.000000] board_bcm963xx: board name: 96328A-1241N
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x03ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
- [ 0.000000] On node 0 totalpages: 16384
- [ 0.000000] free_area_init_node: node 0, pgdat 802cdd60, node_mem_map 81000000
- [ 0.000000] Normal zone: 128 pages used for memmap
- [ 0.000000] Normal zone: 0 pages reserved
- [ 0.000000] Normal zone: 16256 pages, LIFO batch:3
- [ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
- [ 0.000000] pcpu-alloc: [0] 0
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] __ex_table already sorted, skipping sort
- [ 0.000000] Memory: 61464k/65536k available (2296k kernel code, 4072k reserved, 594k data, 244k init, 0k highmem)
- [ 0.000000] NR_IRQS:128
- [ 0.036000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
- [ 0.036000] pid_max: default: 32768 minimum: 301
- [ 0.040000] Mount-cache hash table entries: 512
- [ 0.044000] NET: Registered protocol family 16
- [ 0.272000] registering PCI controller with io_map_base unset
- [ 0.284000] bio: create slab <bio-0> at 0
- [ 0.288000] PCI host bridge to bus 0000:00
- [ 0.292000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff]
- [ 0.296000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
- [ 0.300000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 0.304000] pci 0000:00:00.0: [14e4:6328] type 01 class 0x060400
- [ 0.304000] pci 0000:00:00.0: PME# supported from D0 D3hot
- [ 0.304000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- [ 0.308000] pci 0000:01:00.0: [14e4:a8d8] type 00 class 0x028000
- [ 0.308000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x00003fff 64bit]
- [ 0.308000] pci 0000:01:00.0: supports D1 D2
- [ 0.308000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
- [ 0.308000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
- [ 0.308000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
- [ 0.312000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
- [ 0.316000] pci 0000:00:00.0: PCI bridge to [bus 01]
- [ 0.320000] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff]
- [ 0.324000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
- [ 0.328000] Switching to clocksource MIPS
- [ 0.336000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
- [ 0.344000] bcma: bus0: Found chip with id 0xA8D9, rev 0x01 and package 0x0A
- [ 0.352000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
- [ 0.360000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
- [ 0.368000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
- [ 0.376000] bcma: bus0: Found rev 6 PMU (capabilities 0x108C2606)
- [ 0.376000] bcma: bus0: SPROM offset 0x800
- [ 0.416000] bcma: bus0: invalid sprom read from the PCIe card, try to use fallback sprom
- [ 0.424000] bcm63xx_sprom_bcma: filled sprom for chip id 0xa8d9
- [ 0.432000] bcma: bus0: Using SPROM revision 8 provided by platform.
- [ 0.432000] bcma: bus0: PMU resource config unknown or not needed for device 0xA8D9
- [ 0.432000] bcma: bus0: Workarounds unknown or not needed for device 0xA8D9
- [ 0.440000] bcma: bus0: GPIO driver not activated
- [ 0.440000] bcma: bus0: Bus registered
- [ 0.444000] NET: Registered protocol family 2
- [ 0.452000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.460000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.464000] TCP: Hash tables configured (established 2048 bind 2048)
- [ 0.472000] TCP: reno registered
- [ 0.476000] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.480000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.488000] NET: Registered protocol family 1
- [ 0.492000] PCI: CLS 0 bytes, default 16
- [ 0.496000] audit: initializing netlink socket (disabled)
- [ 0.500000] type=2000 audit(0.500:1): initialized
- [ 0.508000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.512000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.524000] msgmni has been set to 120
- [ 0.528000] io scheduler noop registered
- [ 0.532000] io scheduler deadline registered (default)
- [ 0.540000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart
- [ 0.548000] console [ttyS0] enabled, bootconsole disabled
- [ 0.564000] m25p80 spi0.0: found mx25l12805d, expected m25p80
- [ 0.572000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
- [ 0.576000] bcm63xxpart: CFE boot tag found with version 6 and board type 96328A-1241N
- [ 0.584000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
- [ 0.592000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 10ff00
- [ 0.600000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ed0000
- [ 0.608000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000
- [ 0.616000] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000
- [ 0.620000] bcm63xxpart: Spare partition is offset 410004 and length bdfffc
- [ 0.628000] 5 bcm63xxpart partitions found on MTD device spi0.0
- [ 0.636000] Creating 5 MTD partitions on "spi0.0":
- [ 0.640000] 0x000000000000-0x000000010000 : "CFE"
- [ 0.648000] 0x000000010100-0x000000120000 : "kernel"
- [ 0.652000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
- [ 0.668000] 0x000000120000-0x000000ff0000 : "rootfs"
- [ 0.676000] mtd: partition "rootfs" set to be root filesystem
- [ 0.684000] mtd: partition "rootfs_data" created automatically, ofs=410000, len=BE0000
- [ 0.692000] 0x000000410000-0x000000ff0000 : "rootfs_data"
- [ 0.700000] 0x000000ff0000-0x000001000000 : "nvram"
- [ 0.708000] 0x000000010000-0x000000ff0000 : "linux"
- [ 0.756000] b53_common: found switch: BCM63xx, rev 0
- [ 0.764000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
- [ 0.768000] Registered led device: 96328A-1241N:green:power
- [ 0.772000] Registered led device: 96328A-1241N:red:alarm
- [ 0.772000] Registered led device: 96328A-1241N:green:inet
- [ 0.772000] TCP: cubic registered
- [ 0.776000] NET: Registered protocol family 17
- [ 0.780000] 8021q: 802.1Q VLAN Support v1.8
- [ 0.796000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- [ 0.808000] Freeing unused kernel memory: 244k freed
- [ 3.668000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex
- [ 4.052000] Button Hotplug driver version 0.4.1
- [ 4.080000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
- [ 7.728000] jffs2: notice: (337) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 10 of xref (0 dead, 3 orphan) found.
- [ 9.188000] SCSI subsystem initialized
- [ 9.512000] usbcore: registered new interface driver usbfs
- [ 9.516000] usbcore: registered new interface driver hub
- [ 9.524000] usbcore: registered new device driver usb
- [ 10.336000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 10.448000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
- [ 10.452000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
- [ 10.484000] bcm63xx_ehci bcm63xx_ehci.0: irq 50, io mem 0xb0002500
- [ 10.500000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
- [ 10.508000] hub 1-0:1.0: USB hub found
- [ 10.512000] hub 1-0:1.0: 1 port detected
- [ 10.548000] Initializing USB Mass Storage driver...
- [ 10.552000] usbcore: registered new interface driver usb-storage
- [ 10.560000] USB Mass Storage support registered.
- [ 10.828000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
- [ 10.968000] scsi0 : usb-storage 1-1:1.0
- [ 11.972000] scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
- [ 14.212000] sd 0:0:0:0: [sda] 8060928 512-byte logical blocks: (4.12 GB/3.84 GiB)
- [ 14.224000] sd 0:0:0:0: [sda] Write Protect is off
- [ 14.228000] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
- [ 14.228000] sd 0:0:0:0: [sda] No Caching mode page present
- [ 14.236000] sd 0:0:0:0: [sda] Assuming drive cache: write through
- [ 14.244000] sd 0:0:0:0: [sda] No Caching mode page present
- [ 14.252000] sd 0:0:0:0: [sda] Assuming drive cache: write through
- [ 14.260000] sda: sda1 sda2 sda3
- [ 14.268000] sd 0:0:0:0: [sda] No Caching mode page present
- [ 14.276000] sd 0:0:0:0: [sda] Assuming drive cache: write through
- [ 14.280000] sd 0:0:0:0: [sda] Attached SCSI removable disk
- [ 31.468000] EXT4-fs (sda1): recovery complete
- [ 31.476000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
- [ 33.948000] Compat-drivers backport release: compat-drivers-2013-01-21-1
- [ 33.956000] Backport based on wireless-testing.git master-2013-02-22
- [ 33.960000] compat.git: wireless-testing.git
- [ 34.044000] cfg80211: Calling CRDA to update world regulatory domain
- [ 34.048000] cfg80211: World regulatory domain updated:
- [ 34.056000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 34.064000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 34.072000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 34.080000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 34.088000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 34.096000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 34.572000] lib80211: common routines for IEEE802.11 drivers
- [ 34.576000] lib80211_crypt: registered algorithm 'NULL'
- [ 34.596000] lib80211_crypt: registered algorithm 'WEP'
- [ 34.620000] lib80211_crypt: registered algorithm 'CCMP'
- [ 34.644000] lib80211_crypt: registered algorithm 'TKIP'
- [ 36.056000] usbcore: registered new interface driver usb8xxx
- [ 36.216000] usbcore: registered new interface driver rt2500usb
- [ 36.412000] usbcore: registered new interface driver rt73usb
- [ 36.452000] usbcore: registered new interface driver rtl8187
- [ 36.488000] usbcore: registered new interface driver rt2800usb
- [ 37.132000] PPP generic driver version 2.4.2
- [ 37.580000] brcmsmac bcma0:0: mfg 4bf core 812 rev 23 class 0 irq 31
- [ 37.612000] usbcore: registered new interface driver p54usb
- [ 38.012000] bcma: bus0: Switched to core: 0x812
- [ 38.016000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
- [ 38.216000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 38.564000] NET: Registered protocol family 24
- [ 38.792000] nf_conntrack version 0.5.0 (964 buckets, 3856 max)
- [ 40.088000] usbcore: registered new interface driver ath9k_htc
- [ 40.220000] usbcore: registered new interface driver brcmfmac
- [ 40.364000] usbcore: registered new interface driver carl9170
- [ 40.532000] usbcore: registered new interface driver zd1201
- [ 40.732000] usbcore: registered new interface driver zd1211rw
- [ 45.540000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex
- [ 47.056000] device eth0.1 entered promiscuous mode
- [ 47.064000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex
- [ 47.072000] device eth0 entered promiscuous mode
- [ 47.076000] br-lan: port 1(eth0.1) entered forwarding state
- [ 47.080000] br-lan: port 1(eth0.1) entered forwarding state
- [ 49.084000] br-lan: port 1(eth0.1) entered forwarding state
- [ 53.004000] brcmsmac bcma0:0: brcms_ops_bss_info_changed: qos enabled: false (implement)
- [ 53.012000] brcmsmac bcma0:0: brcms_ops_config: change power-save mode: false (implement)
- [ 57.260000] wlan0: authenticate with
- [ 57.268000] wlan0: send auth to (try 1/3)
- [ 57.276000] wlan0: authenticated
- [ 57.292000] brcmsmac bcma0:0 wlan0: disabling HT/VHT due to WEP/TKIP use
- [ 57.304000] wlan0: associate with (try 1/3)
- [ 57.312000] wlan0: RX AssocResp from (capab=0x431 status=0 aid=2)
- [ 57.324000] brcmsmac bcma0:0: brcmsmac: brcms_ops_bss_info_changed: associated
- [ 57.332000] brcmsmac bcma0:0: brcms_ops_bss_info_changed: qos enabled: true (implement)
- [ 57.340000] wlan0: associated
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement