API tools faq
paste
Advertisement
xamoko

Boot

xamoko
May 16th, 2014
34
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 14.81 KB | None | 0 0
raw download clone embed print report
  1. >
  2. ROM VER: 1.1.4
  3. CFG 05
  4.  
  5. ROM VER: 1.1.4
  6. CFG 05
  7.  
  8. DDR autotuning Rev 0.3ff
  9. DDR size from 0xa0000000 - 0xa3ffffff
  10. DDR check ok... start booting...
  11.  
  12.  
  13.  
  14. U-Boot 2010.06-LANTIQ-v-2.0.40-svn4469 (Aug 28 2013 - 09:28:56)
  15.  
  16. CLOCK CPU 500M RAM 250M
  17. DRAM: 64 MiB
  18. Using default environment
  19.  
  20. In: serial
  21. Out: serial
  22. Err: serial
  23. Net: Internal phy(GE) firmware version: 0x8434
  24. vr9 Switch8192 KiB W25Q64 at 0:3 is now current device
  25.  
  26.  
  27. Type "run flash_nfs" to mount root filesystem over NFS
  28.  
  29. Hit any key to stop autoboot: 0
  30. 8192 KiB W25Q64 at 0:3 is now current device
  31. 8192 KiB W25Q64 at 0:3 is now current device
  32. Uncompressing ...
  33. Starting kernel ...
  34.  
  35. Linux version 3.10.36 (marco@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r40679) ) #14 Sat May 10 12:37:04
  36. SoC: VR9 rev 1.2
  37. bootconsole [early0] enabled
  38. CPU revision is: 00019556 (MIPS 34Kc)
  39. MIPS: machine is TDW8970 - TP-LINK TD-W8970
  40. Determined physical RAM map:
  41. memory: 04000000 @ 00000000 (usable)
  42. Initrd not found or empty - disabling initrd
  43. Zone ranges:
  44. Normal [mem 0x00000000-0x03ffffff]
  45. Movable zone start for each node
  46. Early memory node ranges
  47. node 0: [mem 0x00000000-0x03ffffff]
  48. Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
  49. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  50. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
  51. Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
  52. PID hash table entries: 256 (order: -2, 1024 bytes)
  53. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  54. Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  55. Writing ErrCtl register=0005d560
  56. Readback ErrCtl register=0005d560
  57. Memory: 60544k/65536k available (3090k kernel code, 4992k reserved, 850k data, 208k init, 0k highmem)
  58. NR_IRQS:256
  59. CPU Clock: 500MHz
  60. Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
  61. pid_max: default: 32768 minimum: 301
  62. Mount-cache hash table entries: 512
  63. pinctrl core: initialized pinctrl subsystem
  64. NET: Registered protocol family 16
  65. pinctrl-xway 1e100b10.pinmux: Init done
  66. dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
  67. dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
  68. arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
  69. arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
  70. ath9k,eeprom ath9k_eep.8: failed to find mtd device
  71. bio: create slab <bio-0> at 0
  72. usbcore: registered new interface driver usbfs
  73. usbcore: registered new interface driver hub
  74. usbcore: registered new device driver usb
  75. PCI host bridge to bus 0000:00
  76. pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff]
  77. pci_bus 0000:00: root bus resource [io 0x1d800000-0x1d8fffff]
  78. pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
  79. ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
  80. pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff]
  81. pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref]
  82. pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit]
  83. pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref]
  84. pci 0000:00:00.0: PCI bridge to [bus 01]
  85. pci 0000:00:00.0: bridge window [mem 0x1c000000-0x1c0fffff]
  86. pci 0000:00:00.0: bridge window [mem 0x1c100000-0x1c1fffff pref]
  87. PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
  88. ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1
  89. ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned
  90. ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
  91. ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
  92. Switching to clocksource MIPS
  93. NET: Registered protocol family 2
  94. TCP established hash table entries: 512 (order: 0, 4096 bytes)
  95. TCP bind hash table entries: 512 (order: -1, 2048 bytes)
  96. TCP: Hash tables configured (established 512 bind 512)
  97. TCP: reno registered
  98. UDP hash table entries: 256 (order: 0, 4096 bytes)
  99. UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  100. NET: Registered protocol family 1
  101. gptu: totally 6 16-bit timers/counters
  102. gptu: misc_register on minor 63
  103. gptu: succeeded to request irq 126
  104. gptu: succeeded to request irq 127
  105. gptu: succeeded to request irq 128
  106. gptu: succeeded to request irq 129
  107. gptu: succeeded to request irq 130
  108. gptu: succeeded to request irq 131
  109. phy-xrx200 gphy-xrx200.5: requesting lantiq/vr9_phy11g_a2x.bin
  110. phy-xrx200 gphy-xrx200.5: booting GPHY0 firmware at 38C0000
  111. phy-xrx200 gphy-xrx200.5: booting GPHY1 firmware at 38C0000
  112. squashfs: version 4.0 (2009/01/31) Phillip Lougher
  113. jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  114. msgmni has been set to 118
  115. io scheduler noop registered
  116. io scheduler deadline registered (default)
  117. 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
  118. console [ttyLTQ0] enabled, bootconsole disabled
  119. console [ttyLTQ0] enabled, bootconsole disabled
  120. spi_gpio spi.7: master is unqueued, this is deprecated
  121. m25p80 spi32766.0: found s25fl064k, expected en25q64
  122. m25p80 spi32766.0: s25fl064k (8192 Kbytes)
  123. 4 ofpart partitions found on MTD device spi32766.0
  124. Creating 4 MTD partitions on "spi32766.0":
  125. 0x000000000000-0x000000020000 : "u-boot"
  126. 0x000000020000-0x0000007c0000 : "firmware"
  127. 0x00000016b79c-0x0000007c0000 : "rootfs"
  128. mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing rey
  129. mtd: device 2 (rootfs) set to be root filesystem
  130. mtd: partition "rootfs_data" created automatically, ofs=0x690000, len=0x130000
  131. 0x000000690000-0x0000007c0000 : "rootfs_data"
  132. 0x0000007c0000-0x0000007d0000 : "config"
  133. 0x0000007d0000-0x000000800000 : "boardconfig"
  134. libphy: lantiq,xrx200-mdio: probed
  135. net-xrx200: invalid MAC, using random
  136. eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
  137. eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
  138. eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
  139. eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
  140. wdt 1f8803f0.watchdog: Init done
  141. leds-gpio gpio-leds.10: pins are not configured from the driver
  142. TCP: cubic registered
  143. NET: Registered protocol family 17
  144. Bridge firewalling registered
  145. 8021q: 802.1Q VLAN Support v1.8
  146. ath9k,eeprom ath9k_eep.8: using random mac
  147. ath9k,eeprom ath9k_eep.8: using led pin 0.
  148. ath9k,eeprom ath9k_eep.8: loaded ath9k eeprom
  149. VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  150. Freeing unused kernel memory: 208K (803dc000 - 80410000)
  151. eth0: port 4 got link
  152. procd: Console is alive
  153. procd: - watchdog -
  154. procd: - preinit -
  155. Press the [f] key and hit [enter] to enter failsafe mode
  156. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  157. SCSI subsystem initialized
  158. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  159. IFXUSB: ifxusb_hcd: version 3.2 B110801
  160. Chip Version :000c BurstSize=4
  161. IFXUSB: USB core #0 soft-reset
  162. IFXUSB: USB core #0 soft-reset
  163. ifxusb_hcd ifxusb_hcd: IFX USB Controller
  164. ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
  165. ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
  166. IFXUSB: Init: Power Port (0)
  167. ehci-platform: EHCI generic platform driver
  168. hub 1-0:1.0: USB hub found
  169. hub 1-0:1.0: 1 port detected
  170. IFXUSB: USB core #1 soft-reset
  171. IFXUSB: USB core #1 soft-reset
  172. ifxusb_hcd ifxusb_hcd: IFX USB Controller
  173. ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2
  174. ifxusb_hcd ifxusb_hcd: irq 91, io mem 0xbe106000
  175. IFXUSB: Init: Power Port (0)
  176. hub 2-0:1.0: USB hub found
  177. hub 2-0:1.0: 1 port detected
  178. ifxusb_hcd ifxusb_hcd: requested GPIO 233
  179. usbcore: registered new interface driver usb-storage
  180. kmod: ran 15 iterations
  181. kmod: 3 modules could not be probed
  182. kmod: - ehci-hcd - 0
  183. kmod: dependency not loaded ehci-hcd
  184. kmod: dependency not loaded ehci-hcd
  185. kmod: - ehci-platform - 1
  186. kmod: - gpio-button-hotplug - 0
  187. usb 2-1: new high-speed USB device number 2 using ifxusb_hcd
  188. usb-storage 2-1:1.0: USB Mass Storage device detected
  189. scsi0 : usb-storage 2-1:1.0
  190. scsi 0:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 0 CCS
  191. sd 0:0:0:0: [sda] 16121856 512-byte logical blocks: (8.25 GB/7.68 GiB)
  192. sd 0:0:0:0: [sda] Write Protect is off
  193. sd 0:0:0:0: [sda] No Caching mode page found
  194. sd 0:0:0:0: [sda] Assuming drive cache: write through
  195. sd 0:0:0:0: [sda] No Caching mode page found
  196. sd 0:0:0:0: [sda] Assuming drive cache: write through
  197. sda: sda1
  198. sd 0:0:0:0: [sda] No Caching mode page found
  199. sd 0:0:0:0: [sda] Assuming drive cache: write through
  200. sd 0:0:0:0: [sda] Attached SCSI removable disk
  201. jffs2: notice: (280) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan).
  202. block: extroot: is not ready yet, retrying in 5 seconds
  203. EXT4-fs (sda1): recovery complete
  204. EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
  205. fs-state: switched to extroot
  206. procd: - early -
  207. procd: - watchdog -
  208. procd: - ubus -
  209. procd: - init -
  210. Please press Enter to activate this console.
  211. IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
  212.  
  213. NET: Registered protocol family 10
  214. NET: Registered protocol family 8
  215. NET: Registered protocol family 20
  216. RPC: Registered named UNIX socket transport module.
  217. RPC: Registered udp transport module.
  218. RPC: Registered tcp transport module.
  219. RPC: Registered tcp NFSv4.1 backchannel transport module.
  220. gre: GRE over IPv4 demultiplexor driver
  221. ip_gre: GRE over IPv4 tunneling driver
  222. Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
  223. PPP generic driver version 2.4.2
  224. nf_conntrack version 0.5.0 (949 buckets, 3796 max)
  225. ip6_tables: (C) 2000-2006 Netfilter Core Team
  226. MEI CPE Driver, Version 1.2.0
  227.  
  228. (c) Copyright 2009, Infineon Technologies AG
  229. ### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###
  230.  
  231.  
  232. Lantiq CPE API Driver version: DSL CPE API V4.11.4
  233.  
  234. Predefined debug level: 2
  235. u32 classifier
  236. input device check on
  237. Actions configured
  238. Mirror/redirect action on
  239. fuse init (API version 7.22)
  240. Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2
  241. Backport generated by backports.git backports-20140221-0-g8e94650
  242. ip_tables: (C) 2000-2006 Netfilter Core Team
  243. Infineon Technologies DEU driver version 2.0.0
  244. IFX DEU DES initialized (multiblock).
  245. IFX DEU AES initialized (multiblock).
  246. IFX DEU ARC4 initialized (multiblock).
  247. IFX DEU SHA1 initialized.
  248. IFX DEU MD5 initialized.
  249. IFX DEU SHA1_HMAC initialized.
  250. IFX DEU MD5_HMAC initialized.
  251. PPP MPPE Compression module registered
  252. NET: Registered protocol family 24
  253. PPTP driver version 0.8.5
  254. usbcore: registered new interface driver ums-alauda
  255. usbcore: registered new interface driver ums-cypress
  256. usbcore: registered new interface driver ums-datafab
  257. usbcore: registered new interface driver ums-freecom
  258. usbcore: registered new interface driver ums-isd200
  259. usbcore: registered new interface driver ums-jumpshot
  260. usbcore: registered new interface driver ums-karma
  261. usbcore: registered new interface driver ums-sddr09
  262. usbcore: registered new interface driver ums-sddr55
  263. usbcore: registered new interface driver ums-usbat
  264. usbcore: registered new interface driver usblp
  265. usbcore: registered new interface driver usbserial
  266. usbcore: registered new interface driver usbserial_generic
  267. usbserial: USB Serial support registered for generic
  268. xt_time: kernel timezone is -0000
  269. cfg80211: Calling CRDA to update world regulatory domain
  270. cfg80211: World regulatory domain updated:
  271. cfg80211: DFS Master region: unset
  272. cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
  273. cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
  274. cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
  275. cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
  276. cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
  277. cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
  278. cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
  279. usbcore: registered new interface driver option
  280. usbserial: USB Serial support registered for GSM modem (1-port)
  281. usbcore: registered new interface driver qcserial
  282. usbserial: USB Serial support registered for Qualcomm USB modem
  283. PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
  284. cfg80211: Calling CRDA for country: US
  285. cfg80211: Regulatory domain changed to country: US
  286. cfg80211: DFS Master region: FCC
  287. cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
  288. cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
  289. cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
  290. cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
  291. cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
  292. cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
  293. ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xbc000000, irq=144
  294. device eth0 entered promiscuous mode
  295. br-lan: port 1(eth0) entered forwarding state
  296. br-lan: port 1(eth0) entered forwarding state
  297. br-lan: port 1(eth0) entered forwarding state
  298. ATM1.0.26 ATM (A1) firmware version 0.24
  299. ifxmips_atm: ATM init succeed
  300. cfg80211: Calling CRDA for country: IT
  301. cfg80211: Regulatory domain changed to country: IT
  302. cfg80211: DFS Master region: ETSI
  303. cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
  304. cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
  305. cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
  306. cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm), (0 s)
  307. cfg80211: (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm), (0 s)
  308. cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
  309. IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
  310. device wlan0 entered promiscuous mode
  311. br-lan: port 2(wlan0) entered forwarding state
  312. br-lan: port 2(wlan0) entered forwarding state
  313. br-lan: port 2(wlan0) entered disabled state
  314. br-lan: port 2(wlan0) entered forwarding state
  315. br-lan: port 2(wlan0) entered forwarding state
  316. IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
  317. br-lan: port 2(wlan0) entered forwarding state
  318. �procd: - init complete -
  319.  
  320.  
  321.  
  322. BusyBox v1.19.4 (2014-04-20 01:05:23 CEST) built-in shell (ash)
  323. Enter 'help' for a list of built-in commands.
  324.  
  325. _______ ________ __
  326. | |.-----.-----.-----.| | | |.----.| |_
  327. | - || _ | -__| || | | || _|| _|
  328. |_______|| __|_____|__|__||________||__| |____|
  329. |__| W I R E L E S S F R E E D O M
  330. -----------------------------------------------------
  331. BARRIER BREAKER (Bleeding Edge, r40746)
  332. -----------------------------------------------------
  333. * 1/2 oz Galliano Pour all ingredients into
  334. * 4 oz cold Coffee an irish coffee mug filled
  335. * 1 1/2 oz Dark Rum with crushed ice. Stir.
  336. * 2 tsp. Creme de Cacao
  337. -----------------------------------------------------
  338. root@OpenWrt:/#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!