Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- eugene@home:~$ sudo smartctl /dev/sda -a
- [sudo] password for eugene:
- smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.8.0-21-generic] (local build)
- Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
- === START OF INFORMATION SECTION ===
- Model Family: Seagate Momentus 5400.6
- Device Model: ST9500325AS
- Serial Number: S2W1N81X
- LU WWN Device Id: 5 000c50 03e3b7104
- Firmware Version: 0003SDM1
- User Capacity: 500.107.862.016 bytes [500 GB]
- Sector Size: 512 bytes logical/physical
- Device is: In smartctl database [for details use: -P show]
- ATA Version is: 8
- ATA Standard is: ATA-8-ACS revision 4
- Local Time is: Mon Jun 10 17:13:22 2013 FET
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x82) Offline data collection activity
- was completed without error.
- Auto Offline Data Collection: Enabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 0) seconds.
- Offline data collection
- capabilities: (0x7b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 1) minutes.
- Extended self-test routine
- recommended polling time: ( 139) minutes.
- Conveyance self-test routine
- recommended polling time: ( 2) minutes.
- SCT capabilities: (0x103b) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 10
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x000f 108 099 006 Pre-fail Always - 16178691
- 3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0
- 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 853
- 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
- 7 Seek_Error_Rate 0x000f 079 060 030 Pre-fail Always - 89454094
- 9 Power_On_Hours 0x0032 092 092 000 Old_age Always - 7273
- 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
- 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 756
- 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
- 187 Reported_Uncorrect 0x0032 080 080 000 Old_age Always - 20
- 188 Command_Timeout 0x0032 100 097 000 Old_age Always - 91
- 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
- 190 Airflow_Temperature_Cel 0x0022 061 051 045 Old_age Always - 39 (Min/Max 38/42)
- 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 54
- 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 19
- 193 Load_Cycle_Count 0x0032 028 028 000 Old_age Always - 144607
- 194 Temperature_Celsius 0x0022 039 049 000 Old_age Always - 39 (0 8 0 0 0)
- 195 Hardware_ECC_Recovered 0x001a 056 052 000 Old_age Always - 16178691
- 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
- 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
- 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
- 254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
- SMART Error Log Version: 1
- ATA Error Count: 20 (device log contains only the most recent five errors)
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 20 occurred at disk power-on lifetime: 2139 hours (89 days + 3 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 b3 72 5f 00 Error: UNC at LBA = 0x005f72b3 = 6255283
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 00 08 b0 72 5f 40 00 00:47:38.035 READ FPDMA QUEUED
- ef 02 00 00 00 00 00 00 00:47:37.967 SET FEATURES [Enable write cache]
- 00 00 00 00 00 00 00 ff 00:47:37.935 NOP [Abort queued commands]
- 60 00 08 b0 72 5f 40 00 00:47:35.592 READ FPDMA QUEUED
- ef 02 00 00 00 00 00 00 00:47:35.582 SET FEATURES [Enable write cache]
- Error 19 occurred at disk power-on lifetime: 2139 hours (89 days + 3 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 b3 72 5f 00 Error: UNC at LBA = 0x005f72b3 = 6255283
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 00 08 b0 72 5f 40 00 00:47:35.592 READ FPDMA QUEUED
- ef 02 00 00 00 00 00 00 00:47:35.582 SET FEATURES [Enable write cache]
- 00 00 00 00 00 00 00 ff 00:47:35.458 NOP [Abort queued commands]
- 60 00 08 b0 72 5f 40 00 00:47:33.024 READ FPDMA QUEUED
- ef 02 00 00 00 00 00 00 00:47:33.023 SET FEATURES [Enable write cache]
- Error 18 occurred at disk power-on lifetime: 2139 hours (89 days + 3 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 b3 72 5f 00 Error: UNC at LBA = 0x005f72b3 = 6255283
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 00 08 b0 72 5f 40 00 00:47:33.024 READ FPDMA QUEUED
- ef 02 00 00 00 00 00 00 00:47:33.023 SET FEATURES [Enable write cache]
- 00 00 00 00 00 00 00 ff 00:47:32.960 NOP [Abort queued commands]
- 60 00 08 b0 72 5f 40 00 00:47:30.628 READ FPDMA QUEUED
- ef 02 00 00 00 00 00 00 00:47:30.557 SET FEATURES [Enable write cache]
- Error 17 occurred at disk power-on lifetime: 2139 hours (89 days + 3 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 b3 72 5f 00 Error: UNC at LBA = 0x005f72b3 = 6255283
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 00 08 b0 72 5f 40 00 00:47:30.628 READ FPDMA QUEUED
- ef 02 00 00 00 00 00 00 00:47:30.557 SET FEATURES [Enable write cache]
- 00 00 00 00 00 00 00 ff 00:47:30.523 NOP [Abort queued commands]
- 60 00 08 b0 72 5f 40 00 00:47:28.204 READ FPDMA QUEUED
- ef 02 00 00 00 00 00 00 00:47:28.203 SET FEATURES [Enable write cache]
- Error 16 occurred at disk power-on lifetime: 2139 hours (89 days + 3 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 00 b3 72 5f 00 Error: UNC at LBA = 0x005f72b3 = 6255283
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 00 08 b0 72 5f 40 00 00:47:28.204 READ FPDMA QUEUED
- ef 02 00 00 00 00 00 00 00:47:28.203 SET FEATURES [Enable write cache]
- 00 00 00 00 00 00 00 ff 00:47:28.140 NOP [Abort queued commands]
- 60 00 08 b0 72 5f 40 00 00:47:25.786 READ FPDMA QUEUED
- ef 02 00 00 00 00 00 00 00:47:25.706 SET FEATURES [Enable write cache]
- SMART Self-test log structure revision number 1
- No self-tests have been logged. [To run self-tests, use: smartctl -t]
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement