boot-with-new-kernel-4.2.0

U-Boot 2014.07-tld-4 (Aug 17 2015 - 16:10:11)
ZyXEL NSA310S/320S 1/2-Bay Power Media Server

SoC:   Kirkwood 88F6702_A1
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot:  0
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Partition Map for USB device 0  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            14950400        515da524-01     83
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
13455 bytes read in 215 ms (60.5 KiB/s)
3147200 bytes read in 330 ms (9.1 MiB/s)
7148518 bytes read in 412 ms (16.5 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-4.2.0-kirkwood-tld-1
   Created:      2015-09-12   8:22:14 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3147136 Bytes = 3 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-4.2.0-kirkwood-tld-1
   Created:      2015-09-12   8:22:41 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7148454 Bytes = 6.8 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
   Booting using the fdt blob at 0x1c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 0f44a000, end 0fb1b3a6 ... OK
   Loading Device Tree to 0f443000, end 0f44948e ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.2.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Aug 31 23:12:00 PDT 2015
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine model: Zyxel NSA310S
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootfstype=ext4
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 243588K/262144K available (6019K kernel code, 571K rwdata, 1988K rodata, 284K init, 312K bss, 18556K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc07da1b4   (8009 kB)
[    0.000000]       .init : 0xc07db000 - 0xc0822000   ( 284 kB)
[    0.000000]       .data : 0xc0822000 - 0xc08b0e24   ( 572 kB)
[    0.000000]        .bss : 0xc08b0e24 - 0xc08ff1a4   ( 313 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[    0.000011] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[    0.000504] Console: colour dummy device 80x30
[    0.000540] Calibrating delay loop... 990.41 BogoMIPS (lpj=4952064)
[    0.090102] pid_max: default: 32768 minimum: 301
[    0.090249] Security Framework initialized
[    0.090349] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090374] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.091234] Initializing cgroup subsys blkio
[    0.091271] Initializing cgroup subsys devices
[    0.091298] Initializing cgroup subsys freezer
[    0.091334] Initializing cgroup subsys net_cls
[    0.091436] CPU: Testing write buffer coherency: ok
[    0.091922] Setting up static identity map for 0x8200 - 0x8258
[    0.092285] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[    0.096562] devtmpfs: initialized
[    0.103339] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.103881] prandom: seed boundary self test passed
[    0.108390] prandom: 100 self tests passed
[    0.108416] pinctrl core: initialized pinctrl subsystem
[    0.110146] NET: Registered protocol family 16
[    0.110601] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.140118] cpuidle: using governor ladder
[    0.170115] cpuidle: using governor menu
[    0.170600] Feroceon L2: Enabling L2
[    0.170650] Feroceon L2: Cache support initialised.
[    0.171112] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[    0.177406] No ATAGs?
[    0.211782] vgaarb: loaded
[    0.212214] usbcore: registered new interface driver usbfs
[    0.212306] usbcore: registered new interface driver hub
[    0.212390] usbcore: registered new device driver usb
[    0.213627] clocksource: Switched to clocksource orion_clocksource
[    0.278656] NET: Registered protocol family 2
[    0.279421] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.279467] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.279501] TCP: Hash tables configured (established 2048 bind 2048)
[    0.279572] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.279598] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.279825] NET: Registered protocol family 1
[    0.280278] RPC: Registered named UNIX socket transport module.
[    0.280293] RPC: Registered udp transport module.
[    0.280302] RPC: Registered tcp transport module.
[    0.280310] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.280623] Unpacking initramfs...
[    1.021442] Freeing initrd memory: 6984K (cf44a000 - cfb1c000)
[    1.021568] NetWinder Floating Point Emulator V0.97 (double precision)
[    1.022818] futex hash table entries: 256 (order: -1, 3072 bytes)
[    1.022854] Initialise system trusted keyring
[    1.022982] audit: initializing netlink subsys (disabled)
[    1.023040] audit: type=2000 audit(1.010:1): initialized
[    1.023919] zpool: loaded
[    1.023939] zbud: loaded
[    1.024274] VFS: Disk quotas dquot_6.6.0
[    1.024347] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.025024] NFS: Registering the id_resolver key type
[    1.025093] Key type id_resolver registered
[    1.025104] Key type id_legacy registered
[    1.025134] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.025153] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.025394] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.025988] Key type big_key registered
[    1.048964] Key type asymmetric registered
[    1.048992] Asymmetric key parser 'x509' registered
[    1.049099] bounce: pool size: 64 pages
[    1.049194] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.049214] io scheduler noop registered
[    1.049229] io scheduler deadline registered
[    1.049296] io scheduler cfq registered (default)
[    1.050831] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    1.051634] irq: Cannot allocate irq_descs @ IRQ33, assuming pre-allocated
[    1.052134] irq: Cannot allocate irq_descs @ IRQ65, assuming pre-allocated
[    1.053104] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00
[    1.053128] pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
[    1.053145] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[    1.053162] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.053593] PCI: bus0: Fast back to back transfers disabled
[    1.053921] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.054164] PCI: bus1: Fast back to back transfers enabled
[    1.054272] pci 0000:00:01.0: PCI bridge to [bus 01]
[    1.054619] mv_xor f1060800.xor: Marvell shared XOR driver
[    1.094450] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy )
[    1.134421] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy )
[    1.134654] mv_xor f1060900.xor: Marvell shared XOR driver
[    1.174422] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy )
[    1.214423] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy )
[    1.214929] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.216506] console [ttyS0] disabled
[    1.216577] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 10416666) is a 16550A
[    1.874199] console [ttyS0] enabled
[    1.879134] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1
[    1.885498] nand: Eon NAND 128MiB 3,3V 8-bit
[    1.889755] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.897314] Scanning device for bad blocks
[    1.906536] Bad eraseblock 100 at 0x000000c80000
[    1.916221] Bad eraseblock 200 at 0x000001900000
[    1.969567] libphy: Fixed MDIO Bus: probed
[    1.974150] libphy: orion_mdio_bus: probed
[    1.983526] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    1.990997] mv643xx_eth: Set the PHY to fix link down
[    1.996825] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 5c:f4:ab:df:07:2b
[    2.006070] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.012600] ehci-pci: EHCI PCI platform driver
[    2.017172] ehci-orion: EHCI orion driver
[    2.021376] orion-ehci f1050000.ehci: EHCI Host Controller
[    2.026906] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    2.034720] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000
[    2.053741] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    2.059972] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.066760] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.073973] usb usb1: Product: EHCI Host Controller
[    2.078834] usb usb1: Manufacturer: Linux 4.2.0-kirkwood-tld-1 ehci_hcd
[    2.085436] usb usb1: SerialNumber: f1050000.ehci
[    2.090945] hub 1-0:1.0: USB hub found
[    2.094775] hub 1-0:1.0: 1 port detected
[    2.099704] mousedev: PS/2 mouse device common for all mice
[    2.105754] i2c /dev entries driver
[    2.111882] ht1382 0-0068: rtc core: registered ht1382 as rtc0
[    2.120435] hidraw: raw HID events driver (C) Jiri Kosina
[    2.126302] drop_monitor: Initializing network drop monitor service
[    2.132837] NET: Registered protocol family 17
[    2.137459] Key type dns_resolver registered
[    2.142581] Loading compiled-in X.509 certificates
[    2.147420] registered taskstats version 1
[    2.151572] zswap: loading zswap
[    2.154816] zswap: using zbud pool
[    2.158214] zswap: using lzo compressor
[    2.171762] Key type encrypted registered
[    2.177583] ht1382 0-0068: setting system clock to 2070-01-02 15:51:34 UTC (3155903494)
[    2.188134] Freeing unused kernel memory: 284K (c07db000 - c0822000)
Loading, please wait...
[    2.271081] systemd-udevd[86]: starting version 215
[    2.285993] random: systemd-udevd urandom read with 4 bits of entropy available
[    2.413740] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    2.478443] SCSI subsystem initialized
[    2.540656] sata_mv f1080000.sata: slots 32 ports 2
[    2.575615] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[    2.582320] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.599351] scsi host0: sata_mv
[    2.603020] usb 1-1: Product: USB2.0 Hub
[    2.611780] hub 1-1:1.0: USB hub found
[    2.619624] hub 1-1:1.0: 4 ports detected
[    2.627883] scsi host1: sata_mv
[    2.645152] ata1: SATA max UDMA/133 irq 32
[    2.649239] ata2: SATA max UDMA/133 irq 32
[    2.903667] usb 1-1.3: new high-speed USB device number 3 using orion-ehci
[    2.993671] ata1: SATA link down (SStatus 0 SControl F300)
[    3.014728] usb 1-1.3: New USB device found, idVendor=0781, idProduct=5571
[    3.021595] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.028912] usb 1-1.3: Product: Cruzer Fit
[    3.032992] usb 1-1.3: Manufacturer: SanDisk
[    3.037280] usb 1-1.3: SerialNumber: 4C530005850112109093
[    3.054032] usb-storage 1-1.3:1.0: USB Mass Storage device detected
[    3.060654] scsi host2: usb-storage 1-1.3:1.0
[    3.067007] usbcore: registered new interface driver usb-storage
[    3.076503] usbcore: registered new interface driver uas
[    3.363674] ata2: SATA link down (SStatus 0 SControl F300)
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Waiting for root file system ... [    4.064719] scsi 2:0:0:0: Direct-Access     SanDisk  Cruzer Fit       1.27 PQ: 0 ANSI: 6
[    4.082170] sd 2:0:0:0: [sda] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[    4.091642] sd 2:0:0:0: [sda] Write Protect is off
[    4.097260] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    4.112992]  sda: sda1
[    4.119009] sd 2:0:0:0: [sda] Attached SCSI removable disk
[    4.129080] sd 2:0:0:0: Attached scsi generic sg0 type 0
Begin: Running /scripts/local-block ... done.
done.
Begin: Checking root file system ... fsck from util-linux 2.25.2
fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
[    9.607328] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[   11.040216] systemd-udevd[297]: starting version 215
. ok
[....] Synthesizing the initial hotplug events...[   11.355981] input: gpio_keys as /devices/platform/gpio_keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[   11.556342] orion_wdt: Initial timeout 25 sec
[   11.844602] random: nonblocking pool is initialized
done.
[ ok ] Activating swap...done.
[   12.858990] EXT4-fs (sda1): re-mounted. Opts: (null)
[....] Checking root file system...fsck from util-linux 2.25.2
rootfs: clean, 31415/467712 files, 353638/1868800 blocks
done.
[   13.096457] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.25.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[   16.029776] NET: Registered protocol family 10
[   16.145141] mv643xx_eth: Set the PHY back to auto-negotiation mode
[   16.151461] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1
Copyright 2004-2014 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/5c:f4:ab:df:07:2b
Sending on   LPF/eth0/5c:f4:ab:df:07:2b
Sending on   Socket/fallback
DHCPREQUEST on eth0 to 255.255.255.255 port 67
Unable to set up timer: unexpected error

If you think you have received this message due to a bug rather
than a configuration issue please read the section on submitting
bugs on either our web page at www.isc.org or in the README file
before submitting a bug.  These pages explain the proper
process and the information we find helpful for debugging..

exiting.
Failed to bring up eth0.
done.
[ ok ] Starting rpcbind daemon....
[FAIL] Starting NFS common utilities: statd idmapd failed!
[ ok ] Cleaning up temporary files....
[FAIL] startpar: service(s) returned failure: nfs-common ... failed!
INIT: Entering runlevel: 2
[   17.824301] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled
[   17.834162] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1205 (syslogd)
. ok
[ ok ] Starting system message bus: dbus.
[FAIL] Starting NFS common utilities: statd idmapd failed!
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1206 (klogd)
. ok
[FAIL] startpar: service(s) returned failure: nfs-common ... failed!