Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 2016.03-20579-gd4aa4cc (Feb 10 2017 - 14:23:35 -0700), Build: jenkins-uboot_v2016.03-100
- CPU: Freescale i.MX6Q rev1.2 at 792 MHz
- Reset cause: POR
- Board: Nitrogen6_max
- I2C: ready
- DRAM: 3.8 GiB
- MMC: FSL_SDHC: 0, FSL_SDHC: 1
- SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB, total 2 MiB
- Display: hdmi:1280x720M@60 (1280x720)
- In: serial
- Out: serial
- Err: serial
- Net: Micrel ksz9021 at 6
- FEC [PRIME], usb_ether
- Hit any key to stop autoboot: 0
- AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
- flags: ncq stag pm led clo only pmp pio slum part
- No port device detected!
- ** Bad device size - sata 0 **
- switch to partitions #0, OK
- mmc0 is current device
- 4547 bytes read in 29 ms (152.3 KiB/s)
- ## Executing script at 10008000
- ** File not found uEnv.txt **
- 49361 bytes read in 1221 ms (39.1 KiB/s)
- only CEA modes allowed on HDMI port
- ----------- trying to load /initrd.img
- 6556084 bytes read in 640 ms (9.8 MiB/s)
- 5791064 bytes read in 671 ms (8.2 MiB/s)
- Kernel image @ 0x10800000 [ 0x000000 - 0x585d58 ]
- ## Flattened Device Tree blob at 13000000
- Booting using the fdt blob at 0x13000000
- reserving fdt memory region: addr=13000000 size=d000
- Using Device Tree in place at 13000000, end 1300ffff
- Starting kernel ...
- Booting Linux on physical CPU 0x0
- Initializing cgroup subsys cpu
- Linux version 4.1.15-4-boundary-12x (tele@sabertooth-xenial) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.1) ) #4 SMP PREEMPT Sun Jul 24 18:33:52 MST 2016
- CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d
- CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- Machine model: Freescale i.MX6 Quad Nitrogen6 Max Board
- Reserved memory: created CMA memory pool at 0x62000000, size 320 MiB
- Reserved memory: initialized node linux,cma, compatible id shared-dma-pool
- Memory policy: Data cache writealloc
- PERCPU: Embedded 12 pages/cpu @d00f3000 s17164 r8192 d23796 u49152
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 979775
- Kernel command line: cpu=6Q coherent_pool=64M board=nitrogen6_max mxc_hdmi.only_cea=1 console=ttymxc1,115200 vmalloc=400M consoleblank=0 rootwait fixrtc root=/dev/mmcblk0p1 wlcore.mac=00:19:b8:82:da:b0
- PID hash table entries: 4096 (order: 2, 16384 bytes)
- Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes)
- Inode-cache hash table entries: 131072 (order: 7, 524288 bytes)
- Memory: 3551600K/3932156K available (8196K kernel code, 314K rwdata, 2448K rodata, 1024K init, 444K bss, 52876K reserved, 327680K cma-reserved, 2260988K highmem)
- Virtual kernel memory layout:
- vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
- vmalloc : 0xe6800000 - 0xff000000 ( 392 MB)
- lowmem : 0x80000000 - 0xe6000000 (1632 MB)
- pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
- modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
- .text : 0x80008000 - 0x80b650ac (11637 kB)
- .init : 0x80c00000 - 0x80d00000 (1024 kB)
- .data : 0x80d00000 - 0x80d4ea40 ( 315 kB)
- .bss : 0x80d51000 - 0x80dc0320 ( 445 kB)
- SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- Preemptible hierarchical RCU implementation.
- Additional per-CPU info printed with stalls.
- NR_IRQS:16 nr_irqs:16 16
- L2C-310 erratum 769419 enabled
- L2C-310 enabling early BRESP for Cortex-A9
- L2C-310 full line of zeros enabled for Cortex-A9
- L2C-310 ID prefetch enabled, offset 16 lines
- L2C-310 dynamic clock gating enabled, standby mode enabled
- L2C-310 cache controller enabled, 16 ways, 1024 kB
- L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001
- mxc_clocksource_init 3000000
- Switching to timer-based delay loop, resolution 333ns
- sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns
- clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
- Console: colour dummy device 80x30
- Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)
- pid_max: default: 32768 minimum: 301
- Security Framework initialized
- AppArmor: AppArmor initialized
- Mount-cache hash table entries: 4096 (order: 2, 16384 bytes)
- Mountpoint-cache hash table entries: 4096 (order: 2, 16384 bytes)
- CPU: Testing write buffer coherency: ok
- CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
- Setting up static identity map for 0x10100000 - 0x10100058
- CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
- CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
- CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
- Brought up 4 CPUs
- SMP: Total of 4 processors activated (24.00 BogoMIPS).
- CPU: All CPU(s) started in SVC mode.
- devtmpfs: initialized
- VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
- clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- pinctrl core: initialized pinctrl subsystem
- NET: Registered protocol family 16
- DMA: preallocated 65536 KiB pool for atomic coherent allocations
- cpuidle: using governor ladder
- cpuidle: using governor menu
- CPU identified as i.MX6Q, silicon rev 1.2
- hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
- hw-breakpoint: maximum watchpoint size is 4 bytes.
- imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
- imx-gpc 20dc000.gpc: no fsl,ldo-bypass found!
- mxs-dma 110000.dma-apbh: initialized
- 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25, base_baud = 5000000) is a IMX
- 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 300, base_baud = 5000000) is a IMX
- console [ttymxc1] enabled
- 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 301, base_baud = 5000000) is a IMX
- serial_imx_probe_dt:170
- serial_imx_probe_dt:167
- serial_imx_probe_dt:56
- serial_imx_probe_dt:168
- 21f4000.serial: ttymxc4 at MMIO 0x21f4000 (irq = 302, base_baud = 5000000) is a IMX
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- 2000000.aips-bus:usbphy_nop1 supply vcc not found, using dummy regulator
- 2000000.aips-bus:usbphy_nop2 supply vcc not found, using dummy regulator
- i2c i2c-0: IMX I2C adapter registered
- i2c i2c-0: can't use DMA
- i2c i2c-1: IMX I2C adapter registered
- i2c i2c-1: can't use DMA
- i2c i2c-2: IMX I2C adapter registered
- i2c i2c-2: can't use DMA
- i2c i2c-1: Added multiplexed i2c bus 3
- i2c i2c-1: Added multiplexed i2c bus 4
- i2c-mux-gpio i2cmux@2: 2 port mux on 21a4000.i2c adapter
- i2c i2c-2: Added multiplexed i2c bus 5
- i2c-mux-gpio i2cmux@3: 1 port mux on 21a8000.i2c adapter
- Linux video capture interface: v2.00
- pps_core: LinuxPPS API ver. 1 registered
- pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- PTP clock support registered
- imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
- imx-ipuv3 2800000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
- mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 driver probed
- mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 dphy version is 0x3130302a
- MIPI CSI2 driver module loaded
- Advanced Linux Sound Architecture Driver Initialized.
- Bluetooth: Core ver 2.20
- NET: Registered protocol family 31
- Bluetooth: HCI device and connection manager initialized
- Bluetooth: HCI socket layer initialized
- Bluetooth: L2CAP socket layer initialized
- Bluetooth: SCO socket layer initialized
- NetLabel: Initializing
- NetLabel: domain hash size = 128
- NetLabel: protocols = UNLABELED CIPSOv4
- NetLabel: unlabeled traffic allowed by default
- Switched to clocksource mxc_timer1
- AppArmor: AppArmor Filesystem Enabled
- NET: Registered protocol family 2
- TCP established hash table entries: 16384 (order: 4, 65536 bytes)
- TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
- TCP: Hash tables configured (established 16384 bind 16384)
- UDP hash table entries: 1024 (order: 3, 32768 bytes)
- UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
- NET: Registered protocol family 1
- RPC: Registered named UNIX socket transport module.
- RPC: Registered udp transport module.
- RPC: Registered tcp transport module.
- RPC: Registered tcp NFSv4.1 backchannel transport module.
- Trying to unpack rootfs image as initramfs...
- Freeing initrd memory: 6404K (83a00000 - 84041000)
- CPU PMU: Failed to parse /soc/pmu/interrupt-affinity[0]
- hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
- imx rpmsg driver is registered.
- Bus freq driver module loaded
- futex hash table entries: 1024 (order: 4, 65536 bytes)
- audit: initializing netlink subsys (disabled)
- audit: type=2000 audit(1.540:1): initialized
- VFS: Disk quotas dquot_6.6.0
- VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- squashfs: version 4.0 (2009/01/31) Phillip Lougher
- NFS: Registering the id_resolver key type
- Key type id_resolver registered
- Key type id_legacy registered
- fuse init (API version 7.23)
- bounce: pool size: 64 pages
- io scheduler noop registered
- io scheduler deadline registered
- io scheduler cfq registered (default)
- backlight_lcd supply power not found, using dummy regulator
- backlight_lvds0 supply power not found, using dummy regulator
- backlight_lvds1 supply power not found, using dummy regulator
- ldb 2000000.aips-bus:ldb@020e0008: failed to find valid LVDS channel
- ldb: probe of 2000000.aips-bus:ldb@020e0008 failed with error -22
- mxc_hdmi 20e0000.hdmi_video: Detected HDMI controller 0x13:0xa:0xa0:0xc1
- fbcvt: 1280x720@60: CVT Name - .921M9
- mxc_sdc_fb fb@3: registered mxc display driver hdmi
- mxc_sdc_fb fb@3: 1280x720 h_sync,r,l: 40,110,220 v_sync,l,u: 5,5,20 pixclock=74250000 Hz
- imx-ipuv3 2800000.ipu: try ipu internal clk
- imx-ipuv3 2800000.ipu: disp=0, pixel_clk=74250000 74250000 parent=74250000 div=1
- find_field: [0] = 0x7ff, max=23
- find_field: [1] = 0xfff, max=23
- find_field: [2] = 0x17ff, max=23
- find_field: [0] = 0x820, max=29
- imx-ipuv3 2800000.ipu: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
- mxc_sdc_fb fb@3: 1280x720 h_sync,r,l: 40,110,220 v_sync,l,u: 5,5,20 pixclock=74250000 Hz
- imx-ipuv3 2800000.ipu: try ipu internal clk
- imx-ipuv3 2800000.ipu: disp=0, pixel_clk=74250000 74250000 parent=74250000 div=1
- Console: switching to colour frame buffer device 160x45
- mxc_sdc_fb fb@3: 1280x720 h_sync,r,l: 40,110,220 v_sync,l,u: 5,5,20 pixclock=74250000 Hz
- imx-ipuv3 2800000.ipu: try ipu internal clk
- imx-ipuv3 2800000.ipu: disp=0, pixel_clk=74250000 74250000 parent=74250000 div=1
- mxc_sdc_fb fb@3: 1280x720 h_sync,r,l: 40,110,220 v_sync,l,u: 5,5,20 pixclock=74250000 Hz
- imx-ipuv3 2800000.ipu: try ipu internal clk
- imx-ipuv3 2800000.ipu: disp=0, pixel_clk=74250000 74250000 parent=74250000 div=1
- add tfp410 i2c driver
- imx-sdma 20ec000.sdma: no iram assigned, using external mem
- imx-sdma 20ec000.sdma: no event needs to be remapped
- imx-sdma 20ec000.sdma: loaded firmware 3.3
- imx-sdma 20ec000.sdma: initialized
- imx sema4 driver is registered.
- [drm] Initialized drm 1.1.0 20060810
- [drm] Initialized vivante 1.0.0 20120216 on minor 0
- mxc_sdc_fb fb@3: 640x480 h_sync,r,l: 96,16,48 v_sync,l,u: 2,10,33 pixclock=25175000 Hz
- imx-ipuv3 2800000.ipu: try ipu internal clk
- brd: module loaded
- loop: module loaded
- [max77823_init] start
- ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024
- ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480
- ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000
- ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000
- imx-ipuv3 2800000.ipu: disp=0, pixel_clk=25175000 25142857 parent=264000000 div=10
- ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled
- ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
- ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
- scsi host0: ahci-imx
- ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 312
- m25p80 spi0.0: sst25vf016b (2048 Kbytes)
- 3 ofpart partitions found on MTD device spi0.0
- Creating 3 MTD partitions on "spi0.0":
- 0x000000000000-0x0000000c0000 : "U-Boot"
- 0x0000000c0000-0x0000000c2000 : "env"
- 0x0000000c2000-0x000000200000 : "splash"
- spi_imx 2008000.ecspi: probed
- CAN device driver interface
- 2090000.flexcan supply xceiver not found, using dummy regulator
- flexcan 2090000.flexcan: device registered (reg_base=e6a90000, irq=34)
- 2188000.ethernet supply phy not found, using dummy regulator
- pps pps0: new PPS source ptp0
- libphy: fec_enet_mii_bus: probed
- fec 2188000.ethernet eth0: registered PHC device 0
- ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- ehci-pci: EHCI PCI platform driver
- usbcore: registered new interface driver cdc_acm
- cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
- usbcore: registered new interface driver usb-storage
- usbcore: registered new interface driver usbserial
- usbcore: registered new interface driver usbserial_generic
- usbserial: USB Serial support registered for generic
- usbcore: registered new interface driver cp210x
- usbserial: USB Serial support registered for cp210x
- usbcore: registered new interface driver ftdi_sio
- usbserial: USB Serial support registered for FTDI USB Serial Device
- usbcore: registered new interface driver keyspan
- usbserial: USB Serial support registered for Keyspan - (without firmware)
- usbserial: USB Serial support registered for Keyspan 1 port adapter
- usbserial: USB Serial support registered for Keyspan 2 port adapter
- usbserial: USB Serial support registered for Keyspan 4 port adapter
- usbcore: registered new interface driver pl2303
- usbserial: USB Serial support registered for pl2303
- usbcore: registered new interface driver qcserial
- usbserial: USB Serial support registered for Qualcomm USB modem
- 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator
- setup_reset_gpios:-2, flags 0
- setup_reset_gpios:204, flags 1
- setup_reset_gpios:-2, flags 0
- 2184200.usb supply vbus not found, using dummy regulator
- ci_hdrc ci_hdrc.1: EHCI Host Controller
- ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
- ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- mousedev: PS/2 mouse device common for all mice
- rtc-rv4162 0-0068: rv4162_probe: chip found: flags 0x00
- rtc-rv4162 0-0068: rtc core: registered rtc-rv4162 as rtc0
- check_alarm_past: alarm in the past
- snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
- i2c /dev entries driver
- mxc_v4l2_output v4l2_out: V4L2 device registered as video16
- mxc_v4l2_output v4l2_out: V4L2 device registered as video17
- imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
- device-mapper: ioctl: 4.31.0-ioctl (2015-3-12) initialised: dm-devel@redhat.com
- sdhci: Secure Digital Host Controller Interface driver
- sdhci: Copyright(c) Pierre Ossman
- sdhci-pltfm: SDHCI platform and OF driver helper
- /soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified
- sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found
- mmc2: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
- /soc/aips-bus@02100000/usdhc@02198000: voltage-ranges unspecified
- sdhci-esdhc-imx 2198000.usdhc: could not get ultra high speed state, work on normal mode
- sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO
- sdhci-esdhc-imx 2198000.usdhc: No vqmmc regulator found
- sdhci-esdhc-imx 2194000.usdhc: card claims to support voltages below defined range
- mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
- /soc/aips-bus@02100000/usdhc@0219c000: voltage-ranges unspecified
- sdhci-esdhc-imx 219c000.usdhc: could not get ultra high speed state, work on normal mode
- sdhci-esdhc-imx 219c000.usdhc: No vqmmc regulator found
- mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA
- mxc_vpu 2040000.vpu_fsl: VPU initialized
- mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
- mxc_hdmi_cec soc:hdmi_cec@00120000: HDMI CEC initialized
- caam 2100000.caam: Entropy delay = 3200
- ata1: SATA link down (SStatus 0 SControl 300)
- ahci-imx 2200000.sata: no device found, disabling link.
- ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug
- caam 2100000.caam: Instantiated RNG4 SH0
- mmc0: host does not support reading read-only switch, assuming write-enable
- mmc0: new high speed SDHC card at address aaaa
- mmcblk0: mmc0:aaaa SS04G 3.69 GiB
- mmcblk0: p1
- caam 2100000.caam: Instantiated RNG4 SH1
- caam 2100000.caam: device ID = 0x0a16010000000000 (Era -524)
- caam 2100000.caam: job rings = 2, qi = 0
- mmc1: MAN_BKOPS_EN bit is not set
- caam algorithms registered in /proc/crypto
- caam_jr 2101000.jr0: registering rng-caam
- usbcore: registered new interface driver usbhid
- usbhid: USB HID core driver
- mmc1: new DDR MMC card at address 0001
- mmcblk1: mmc1:0001 S10004 3.56 GiB
- mmcblk1boot0: mmc1:0001 S10004 partition 1 4.00 MiB
- mmcblk1boot1: mmc1:0001 S10004 partition 2 4.00 MiB
- mmcblk1rpmb: mmc1:0001 S10004 partition 3 4.00 MiB
- sgtl5000 0-000a: sgtl5000 revision 0x11
- mmc2: queuing unknown CIS tuple 0x91 (3 bytes)
- mmc2: new SDIO card at address 0001
- mxc_sdc_fb fb@3: 1280x720 h_sync,r,l: 40,110,220 v_sync,l,u: 5,5,20 pixclock=74250000 Hz
- imx-ipuv3 2800000.ipu: try ipu internal clk
- imx-ipuv3 2800000.ipu: disp=0, pixel_clk=74250000 74250000 parent=74250000 div=1
- sgtl5000 0-000a: Using internal LDO instead of VDDD
- imx-sgtl5000 sound: sgtl5000 <-> 2028000.ssi mapping ok
- imx-audio-hdmi sound-hdmi: hdmi-hifi <-> soc:hdmi_audio@00120000 mapping ok
- NET: Registered protocol family 26
- NET: Registered protocol family 10
- sit: IPv6 over IPv4 tunneling driver
- NET: Registered protocol family 17
- can: controller area network core (rev 20120528 abi 9)
- NET: Registered protocol family 29
- can: raw protocol (rev 20120528)
- can: broadcast manager protocol (rev 20120528 t)
- can: netlink gateway (rev 20130117) max_hops=1
- Bluetooth: RFCOMM TTY layer initialized
- Bluetooth: RFCOMM socket layer initialized
- Bluetooth: RFCOMM ver 1.11
- Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- Bluetooth: BNEP filters: protocol multicast
- Bluetooth: BNEP socket layer initialized
- 8021q: 802.1Q VLAN Support v1.8
- rfkill_gpio bt_rfkill: bt_rfkill device registered.
- Key type dns_resolver registered
- Registering SWP/SWPB emulation handler
- AppArmor: AppArmor sha1 policy hashing enabled
- imx6q-pcie 1ffc000.pcie: Link up, Gen=1
- imx6q-pcie 1ffc000.pcie: PCI host bridge to bus 0000:00
- pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
- pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]
- pci_bus 0000:00: root bus resource [bus 00-ff]
- PCI: bus0: Fast back to back transfers disabled
- pci 0000:01:00.0: Setting PCI class for tw6869 PCIe device
- PCI: bus1: Fast back to back transfers disabled
- pci 0000:00:00.0: BAR 0: assigned [mem 0x01000000-0x010fffff]
- pci 0000:00:00.0: BAR 9: assigned [mem 0x01100000-0x011fffff pref]
- pci 0000:00:00.0: BAR 6: assigned [mem 0x01200000-0x0120ffff pref]
- pci 0000:01:00.0: BAR 0: assigned [mem 0x01100000-0x01100fff pref]
- pci 0000:00:00.0: PCI bridge to [bus 01]
- pci 0000:00:00.0: bridge window [mem 0x01100000-0x011fffff pref]
- pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
- pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
- rtc-rv4162 0-0068: setting system clock to 2017-02-15 11:56:54 UTC (1487159814)
- wlan-en: disabling
- usb_otg_vbus: disabling
- ALSA device list:
- #0: imx6q-nitrogen6_max-sgtl5000
- #1: imx-hdmi-soc
- Freeing unused kernel memory: 1024K (80c00000 - 80d00000)
- Loading, please wait...
- starting version 229
- random: systemd-udevd urandom read with 13 bits of entropy available
- usb 1-1: new high-speed USB device number 2 using ci_hdrc
- hub 1-1:1.0: USB hub found
- hub 1-1:1.0: 3 ports detected
- usb 1-1.1: new full-speed USB device number 3 using ci_hdrc
- input: A4TECH USB Device as /devices/soc0/soc/2100000.aips-bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-1.1:1.0/0003:09DA:054F.0001/input/input0
- hid-generic 0003:09DA:054F.0001: input: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-ci_hdrc.1-1.1/input0
- input: A4TECH USB Device as /devices/soc0/soc/2100000.aips-bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-1.1:1.1/0003:09DA:054F.0002/input/input1
- hid-generic 0003:09DA:054F.0002: input: USB HID v1.11 Mouse [A4TECH USB Device] on usb-ci_hdrc.1-1.1/input1
- Begin: Loading essential drivers ... done.
- Begin: Running /scripts/init-premount ... done.
- Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
- Begin: Running /scripts/local-premount ... ext4
- done.
- Begin: Will now check root file system ... fsck from util-linux 2.27.1
- [/sbin/fsck.ext4 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0 /dev/mmcblk0p1
- xenial: recovering journal
- xenial: clean, 172164/235712 files, 802579/941824 blocks
- done.
- EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
- done.
- Begin: Running /scripts/local-bottom ... done.
- Begin: Running /scripts/init-bottom ... done.
- systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
- systemd[1]: Detected architecture arm.
- Welcome to Ubuntu 16.04.1 LTS!
- systemd[1]: Set hostname to <nitrogen>.
- systemd[1]: Reached target Remote File Systems (Pre).
- [ OK ] Reached target Remote File Systems (Pre).
- systemd[1]: Listening on Journal Audit Socket.
- [ OK ] Listening on Journal Audit Socket.
- systemd[1]: Listening on fsck to fsckd communication Socket.
- [ OK ] Listening on fsck to fsckd communication Socket.
- systemd[1]: Created slice System Slice.
- [ OK ] Created slice System Slice.
- systemd[1]: Reached target Encrypted Volumes.
- [ OK ] Reached target Encrypted Volumes.
- systemd[1]: Created slice User and Session Slice.
- [ OK ] Created slice User and Session Slice.
- systemd[1]: Listening on Journal Socket.
- [ OK ] Listening on Journal Socket.
- systemd[1]: Started Read required files in advance.
- [ OK ] Started Read required files in advance.
- systemd[1]: Listening on Journal Socket (/dev/log).
- [ OK ] Listening on Journal Socket (/dev/log).
- systemd[1]: Starting Journal Service...
- Starting Journal Service...
- systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
- [ OK ] Set up automount Arbitrary Executab...ats File System Automount Point.
- systemd[1]: Created slice system-serial\x2dgetty.slice.
- [ OK ] Created slice system-serial\x2dgetty.slice.
- systemd[1]: Reached target Remote File Systems.
- [ OK ] Reached target Remote File Systems.
- systemd[1]: Started Forward Password Requests to Wall Directory Watch.
- [ OK ] Started Forward Password Requests to Wall Directory Watch.
- systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
- [ OK ] Listening on /dev/initctl Compatibility Named Pipe.
- systemd[1]: Reached target User and Group Name Lookups.
- [ OK ] Reached target User and Group Name Lookups.
- systemd[1]: Starting Uncomplicated firewall...
- Starting Uncomplicated firewall...
- systemd[1]: Starting Set console keymap...
- Starting Set console keymap...
- systemd[1]: Starting Remount Root and Kernel File Systems...
- Starting Remount Root and Kernel File Systems...
- EXT4-fs (mmcblk0p1): re-mounted. Opts: errors=remount-ro
- systemd[1]: Starting Load Kernel Modules...
- Starting Load Kernel Modules...
- systemd[1]: Mounting Debug File System...
- Mounting Debug File System...
- systemd[1]: Reached target Slices.
- [ OK ] Reached target Slices.
- systemd[1]: Starting Create list of required static device nodes for the current kernel...
- Starting Create list of required st... nodes for the current kernel...
- systemd[1]: Listening on udev Kernel Socket.
- [ OK ] Listening on udev Kernel Socket.
- systemd[1]: Listening on udev Control Socket.
- [ OK ] Listening on udev Control Socket.
- systemd[1]: Mounted Debug File System.
- [ OK ] Mounted Debug File System.
- systemd[1]: Started Journal Service.
- [ OK ] Started Journal Service.
- [ OK ] Started Uncomplicated firewall.
- [ OK ] Started Set console keymap.
- [ OK ] Started Remount Root and Kernel File Systems.
- [ OK ] Started Load Kernel Modules.
- [ OK ] Started Create list of required sta...ce nodes for the current kernel.
- Starting Create Static Device Nodes in /dev...
- Mounting Configuration File System...
- Starting Apply Kernel Variables...
- Mounting FUSE Control File System...
- Starting udev Coldplug all Devices...
- Starting Load/Save Random Seed...
- Starting Flush Journal to Persistent Storage...
- [ OK ] Mounted FUSE Control File System.
- [ OK ] Mounted Configuration File System.
- [ OK ] Started Create Static Device Nodes in /dev.
- [ OK ] Started Apply Kernel Variables.
- [ OK ] Started Load/Save Random Seed.
- [ OK ] Started Flush Journal to Persistent Storage.
- [ OK ] Reached target Local File Systems (Pre).
- [ OK ] Reached target Local File Systems.
- Starting Set console font and keymap...
- Starting Raise network interfaces...
- Starting Tell Plymouth To Write Out Runtime Data...
- Starting Create Volatile Files and Directories...
- Starting udev Kernel Device Manager...
- [ OK ] Started udev Coldplug all Devices.
- [ OK ] Started Tell Plymouth To Write Out Runtime Data.
- [ OK ] Started Create Volatile Files and Directories.
- Starting Update UTMP about System Boot/Shutdown...
- [ OK ] Reached target System Time Synchronized.
- [ OK ] Started Update UTMP about System Boot/Shutdown.
- [ OK ] Started udev Kernel Device Manager.
- [ OK ] Started Dispatch Password Requests to Console Directory Watch.
- [ OK ] Reached target Paths.
- [ OK ] Started Set console font and keymap.
- [ OK ] Created slice system-getty.slice.
- [ OK ] Created slice system-systemd\x2dbacklight.slice.
- Starting Load/Save Screen Backlight...ss of backlight:backlight_lcd...
- Starting Load/Save Screen Backlight... of backlight:backlight_lvds1...
- Starting Load/Save Screen Backlight... of backlight:backlight_lvds0...
- [ OK ] Started Load/Save Screen Backlight ...ss of backlight:backlight_lvds1.
- [ OK ] Started Load/Save Screen Backlight ...ness of backlight:backlight_lcd.
- [ OK ] Started Load/Save Screen Backlight ...ss of backlight:backlight_lvds0.
- ft5x06-ts 2-0038: Could not detect touch screen -19.
- ft5x06-ts 3-0038: Could not detect touch screen -19.
- egalax_ts 2-0004: Failed to read firmware version
- tc358743_read_reg:reg=0 ret=-5
- tc358743_probe:cannot find camera
- tc358743_probe: failed, error=-19
- ov5640_read_reg:write reg error:reg=300a
- Goodix-TS 2-0014: i2c test failed attempt 1: -5
- Goodix-TS 2-0014: i2c test failed attempt 2: -5
- Goodix-TS 2-0014: I2C communication failure: -5
- [ OK ] Found device /dev/ttymxc1.
- Goodix-TS 2-005d: i2c test failed attempt 1: -5
- [ OK ] Started ifup for eth0.
- Goodix-TS 2-005d: i2c test failed attempt 2: -5
- [ OK ] Found device /sys/subsystem/net/devices/eth0.
- Goodix-TS 2-005d: I2C communication failure: -5
- atmel_mxt_ts 2-004a: not detected
- ili210x_i2c 2-0041: i2c transfer failed
- ili210x_i2c 2-0041: Failed to get firmware version, err: -5
- tsc2004_reset: write_cmd -5
- tsc2004 2-0048: Failed to reset TSC -5
- [ OK ] Reached target Sound Card.
- ov5640_read_reg(mipi):reg=300a ret=-5
- ov5642_read_reg:write reg error:reg=300a
- [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
- Starting Load/Save RF Kill Switch Status...
- [ OK ] Started Load/Save RF Kill Switch Status.
- mxc_v4l_open: Mxc Camera no sensor ipu0/csi1
- mxc_v4l_open: Mxc Camera no sensor ipu0/csi0
- mxc_v4l_open: Mxc Camera no sensor ipu1/csi1
- mxc_v4l_open: Mxc Camera no sensor ipu0/csi0
- [ OK ] Stopped LSB: Start NTP daemon.
- [ OK ] Started Raise network interfaces.
- [ OK ] Stopped LSB: Start NTP daemon.
- [ TIME ] Timed out waiting for device dev-sda5.device.
- [DEPEND] Dependency failed for /dev/sda5.
- [DEPEND] Dependency failed for Swap.
- [ OK ] Reached target System Initialization.
- [ OK ] Listening on D-Bus System Message Bus Socket.
- [ OK ] Reached target Sockets.
- [ OK ] Reached target Basic System.
- Starting Bluetooth service...
- Starting Accounts Service...
- Starting LSB: desktop iconset selector...
- [ OK ] Started D-Bus System Message Bus.
- [ OK ] Started Bluetooth service.
- [ OK ] Reached target Bluetooth.
- Starting Network Manager...
- Starting Restore /etc/resolv.conf i...re the ppp link was shut down...
- Starting Login Service...
- Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"...
- Starting Save/Restore Sound Card State...
- Starting LSB: Set sysfs variables from /etc/sysfs.conf...
- [ OK ] Started Daily apt activities.
- Starting Permit User Sessions...
- [ OK ] Started Daily Cleanup of Temporary Directories.
- [ OK ] Reached target Timers.
- [ OK ] Started Run anacron jobs.
- Starting LSB: setting xorg.conf...
- Starting Attaching uart to bluetooth...
- Starting autohdmi.service...
- Starting Modem Manager...
- [ OK ] Started Restore /etc/resolv.conf if...fore the ppp link was shut down.
- [ OK ] Started Permit User Sessions.
- [ OK ] Started Save/Restore Sound Card State.
- [ OK ] Started autohdmi.service.
- [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand".
- [ OK ] Started LSB: setting xorg.conf.
- [ OK ] Started LSB: Set sysfs variables from /etc/sysfs.conf.
- [ OK ] Started Login Service.
- Starting Authenticate and Authorize Users to Run Privileged Tasks...
- Starting Hostname Service...
- Starting Light Display Manager...
- Starting Load/Save RF Kill Switch Status...
- [ OK ] Started Load/Save RF Kill Switch Status.
- [ OK ] Started Hostname Service.
- [ OK ] Started Network Manager.
- [ OK ] Reached target Network.
- Starting OpenBSD Secure Shell server...
- Starting Network Manager Wait Online...
- [ OK ] Started Authenticate and Authorize Users to Run Privileged Tasks.
- [ OK ] Started Accounts Service.
- Starting Network Manager Script Dispatcher Service...
- [ OK ] Started Modem Manager.
- [ OK ] Started Network Manager Script Dispatcher Service.
- [ OK ] Started Light Display Manager.
- Starting WPA supplicant...
- [ OK ] Started OpenBSD Secure Shell server.
- [ OK ] Started LSB: desktop iconset selector.
- [ OK ] Started Network Manager Wait Online.
- [ OK ] Reached target Network is Online.
- Starting LSB: disk temperature monitoring daemon...
- Starting /etc/rc.local Compatibility...
- [ OK ] Started /etc/rc.local Compatibility.
- [ OK ] Started LSB: disk temperature monitoring daemon.
- [ OK ] Started WPA supplicant.
- Starting Hold until boot process finishes up...
- [ OK ] Started Hold until boot process finishes up.
- Starting Set console scheme...
- [ OK ] Started Getty on tty1.
- [ OK ] Started Serial Getty on ttymxc1.
- [ OK ] Reached target Login Prompts.
- [ OK ] Reached target Multi-User System.
- [ OK ] Started Set console scheme.
- [ OK ] Created slice User Slice of ubuntu.
- Starting User Manager for UID 1000...
- [ OK ] Started Session c1 of user ubuntu.
- [ OK ] Started Attaching uart to bluetooth.
- [ OK ] Started User Manager for UID 1000.
- [ OK ] Reached target Graphical Interface.
- [ OK ] Started Stop ureadahead data collection 45s after completed startup.
- Starting Update UTMP about System Runlevel Changes...
- [ OK ] Started Update UTMP about System Runlevel Changes.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement