Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- barebox@Freescale i.MX53 LOCO:/mkdir /mnt/disk1
- barebox@Freescale i.MX53 LOCO:/ bootargs="root=/dev/mmcblk0p3 rootwait rootfstype=ext4"
- barebox@Freescale i.MX53 LOCO:/ mount /dev/disk0.1 fat /mnt/disk1
- barebox@Freescale i.MX53 LOCO:/ bootm /mnt/disk1/uImage
- Image Name: Linux-2.6.35.3
- Created: 2013-06-13 14:17:14 UTC
- OS: Linux
- Architecture: ARM
- Type: Kernel Image
- Compression: uncompressed
- Data Size: 2945628 Bytes = 2.8 MiB
- Load Address: 70008000
- Entry Point: 70008000
- Loading OS U-Boot uImage '/mnt/disk1/uImage'
- commandline: console=ttymxc0,115200
- arch_number: 3273
- Linux version 2.6.35.3 (testserver@Server6) (gcc version 4.7.3 (Buildroot 2013.05) ) #1 PREEMPT Thu Jun 13 16:17:07 CEST 2013
- CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f
- CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
- Machine: Freescale MX53 LOCO Board
- Memory policy: ECC disabled, Data cache writeback
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 250880
- Kernel command line: console=ttymxc0,115200
- PID hash table entries: 4096 (order: 2, 16384 bytes)
- Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
- Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
- Memory: 480MB 512MB = 992MB total
- Memory: 998308k/998308k available, 17500k reserved, 0K highmem
- Virtual kernel memory layout:
- vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- DMA : 0xf9e00000 - 0xffe00000 ( 96 MB)
- vmalloc : 0xe0800000 - 0xf4000000 ( 312 MB)
- lowmem : 0x80000000 - 0xe0000000 (1536 MB)
- pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
- modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
- .init : 0x80008000 - 0x80032000 ( 168 kB)
- .text : 0x80032000 - 0x807de000 (7856 kB)
- .data : 0x80802000 - 0x8085a0c0 ( 353 kB)
- SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- Hierarchical RCU implementation.
- RCU-based detection of stalled CPUs is disabled.
- Verbose stalled-CPUs detection is disabled.
- NR_IRQS:368
- MXC GPIO hardware
- MXC IRQ initialized
- MXC_Early serial console at MMIO 0x53fbc000 (options '115200')
- bootconsole [ttymxc0] enabled
- Console: colour dummy device 80x30
- Calibrating delay loop... 999.42 BogoMIPS (lpj=4997120)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 512
- CPU: Testing write buffer coherency: ok
- regulator: core version 0.5
- NET: Registered protocol family 16
- i.MX IRAM pool: 128 KB@0xe0840000
- IRAM READY
- CPU is i.MX53 Revision 2.1
- Using SDMA I.API
- MXC DMA API initialized
- IMX usb wakeup probe
- IMX usb wakeup probe
- bio: create slab <bio-0> at 0
- SCSI subsystem initialized
- Freescale USB OTG Driver loaded, $Revision: 1.55 $
- ****************************** NOTICE *****************************
- You have seen this notice as you have enabled OTG driver for mx53 LOCO board
- For mx53 loco board, the OTG function is unavailable due to hardware limitation
- So, Only one usb function (device or host) can be available for certain image
- Please config your kernel to disable OTG and the usb function you don't want to use
- And remain the other usb function you would like to use
- Below OTG configs should be removed:
- CONFIG_MXC_OTG, CONFIG_USB_OTG
- Choose one of below configs for host or device function
- But DO NOT choose them together
- OTG host config
- CONFIG_USB_EHCI_ARC_OTG
- OTG device config
- CONFIG_USB_GADGET
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- da9052_ssc_i2c 0-0048: 2 - da9052_i2c_read:master_xfer Failed!!
- da9052_i2c_is_connected - i2c read failed.....
- da9052_ssc_i2c 0-0048: 2 - da9052_i2c_read:master_xfer Failed!!
- da9052_i2c_is_connected - i2c read failed.....
- da9052_ssc_i2c 0-0048: 2 - da9052_i2c_read:master_xfer Failed!!
- da9052_i2c_is_connected - i2c read failed.....
- da9052_ssc_i2c 0-0048: 2 - da9052_i2c_read:master_xfer Failed!!
- da9052_i2c_is_connected - i2c read failed.....
- da9052_ssc_i2c 0-0048: 2 - da9052_i2c_read:master_xfer Failed!!
- da9052_i2c_is_connected - i2c read failed.....
- da9052_ssc_i2c 0-0048: 2 - da9052_i2c_read:master_xfer Failed!!
- da9052_i2c_is_connected - i2c read failed.....
- da9052_ssc_i2c 0-0048: 2 - da9052_i2c_read:master_xfer Failed!!
- da9052_i2c_is_connected - i2c read failed.....
- da9052_ssc_i2c 0-0048: 2 - da9052_i2c_read:master_xfer Failed!!
- da9052_i2c_is_connected - i2c read failed.....
- da9052_ssc_i2c 0-0048: 2 - da9052_i2c_read:master_xfer Failed!!
- da9052_i2c_is_connected - i2c read failed.....
- da9052_ssc_i2c 0-0048: 2 - da9052_i2c_read:master_xfer Failed!!
- da9052_i2c_is_connected - i2c read failed.....
- da9052_ssc_i2c 0-0048: 2 - da9052_i2c_read:master_xfer Failed!!
- da9052_i2c_is_connected - i2c read failed.....
- IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
- Advanced Linux Sound Architecture Driver Version 1.0.23.
- Bluetooth: Core ver 2.15
- NET: Registered protocol family 31
- Bluetooth: HCI device and connection manager initialized
- Bluetooth: HCI socket layer initialized
- Switching to clocksource mxc_timer1
- NET: Registered protocol family 2
- IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
- TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
- TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
- TCP: Hash tables configured (established 131072 bind 65536)
- TCP reno registered
- UDP hash table entries: 512 (order: 1, 8192 bytes)
- UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
- NET: Registered protocol family 1
- RPC: Registered udp transport module.
- RPC: Registered tcp transport module.
- RPC: Registered tcp NFSv4.1 backchannel transport module.
- LPMode driver module loaded
- Static Power Management for Freescale i.MX5
- PM driver module loaded
- sdram autogating driver module loaded
- Bus freq driver module loaded
- DI1 is primary
- mxc_dvfs_core_probe
- mxc_dvfs_core_probe: failed to get gp regulator
- DVFS driver module loaded
- i.MXC CPU frequency driver
- mxc_cpufreq_driver_init: failed to get gp regulator
- DVFS PER driver module loaded
- JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
- msgmni has been set to 1949
- alg: No test for stdrng (krng)
- cryptodev: driver loaded.
- io scheduler noop registered
- io scheduler deadline registered
- io scheduler cfq registered (default)
- regulator: get() with no identifier
- By setting, SII driver will not be enabled
- By setting, LDB driver will not be enabled
- mxc_ipu mxc_ipu: Channel already disabled 9
- mxc_ipu mxc_ipu: Channel already uninitialized 9
- IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
- Console: switching to colour frame buffer device 128x48
- mxc_ipu mxc_ipu: Channel already disabled 7
- mxc_ipu mxc_ipu: Channel already uninitialized 7
- mxc_ipu mxc_ipu: Channel already disabled 10
- mxc_ipu mxc_ipu: Channel already uninitialized 10
- Serial: MXC Internal UART driver
- mxcintuart.0: ttymxc0 at MMIO 0x53fbc000 (irq = 31) is a Freescale i.MX
- console [ttymxc0] enabled, bootconsole disabled
- console [ttymxc0] enabled, bootconsole disabled
- mxcintuart.1: ttymxc1 at MMIO 0x53fc0000 (irq = 32) is a Freescale i.MX
- mxcintuart.2: ttymxc2 at MMIO 0x5000c000 (irq = 33) is a Freescale i.MX
- mxcintuart.3: ttymxc3 at MMIO 0x53ff0000 (irq = 13) is a Freescale i.MX
- mxcintuart.4: ttymxc4 at MMIO 0x63f90000 (irq = 86) is a Freescale i.MX
- loop: module loaded
- MXC MTD nand Driver 3.0
- i.MX GPMI NFC
- vcan: Virtual CAN interface driver
- Freescale FlexCAN Driver
- FEC Ethernet Driver
- fec_enet_mii_bus: probed
- ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
- fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
- fsl-ehci fsl-ehci.0: irq 18, io base 0x53f80000
- fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
- fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
- fsl-ehci fsl-ehci.1: irq 14, io base 0x53f80200
- fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 1 port detected
- usbcore: registered new interface driver cdc_acm
- cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- ARC USBOTG Device Controller driver (1 August 2005)
- mice: PS/2 mouse device common for all mice
- input: gpio-keys as /devices/platform/gpio-keys/input/input0
- MXC keypad loaded
- egalax_ts 2-0004: egalax_ts: failed to read firmware version
- egalax_ts: probe of 2-0004 failed with error -5
- p1003_fwv33 2-0041: couldn't read panel infomation.
- p1003_fwv33: probe of 2-0041 failed with error -5
- DA9052 TSI Device Driver, v1.0
- mxc_rtc mxc_rtc.0: rtc core: registered mxc_rtc as rtc0
- i2c /dev entries driver
- IR NEC protocol handler initialized
- IR RC5(x) protocol handler initialized
- IR RC6 protocol handler initialized
- IR JVC protocol handler initialized
- IR Sony protocol handler initialized
- Linux video capture interface: v2.00
- mxc_v4l2_output mxc_v4l2_output.0: Registered device video0
- usbcore: registered new interface driver uvcvideo
- USB Video Class driver (v0.1.0)
- APM Battery Driver
- check mma8450 chip ID
- mma8450 0-001c: build time Jun 13 2013 16:11:38
- input: mma8450 as /devices/virtual/input/input1
- add mma8450 i2c driver
- MXC WatchDog Driver 2.0
- MXC Watchdog # 0 Timer: initial timeout 60 sec
- Bluetooth: Virtual HCI driver ver 1.3
- Bluetooth: HCI UART driver ver 2.2
- Bluetooth: HCIATH3K protocol initialized
- Bluetooth: Generic Bluetooth USB driver ver 0.6
- usbcore: registered new interface driver btusb
- VPU initialized
- mxc_asrc registered
- gpu mmu enabled
- mxsdhci: MXC Secure Digital Host Controller Interface driver
- mxsdhci: MXC SDHCI Controller Driver.
- mmc0: SDHCI detect irq 0 irq 1 INTERNAL DMA
- mxsdhci: MXC SDHCI Controller Driver.
- mmc1: SDHCI detect irq 203 irq 3 INTERNAL DMA
- usbcore: registered new interface driver usbhid
- usbhid: USB HID core driver
- Cirrus Logic CS42888 ALSA SoC Codec Driver
- sgtl5000-i2c 1-000a: SGTL5000 revision 17
- mxc_spdif mxc_spdif.0: MXC SPDIF Audio Transmitter
- No device for codec mxc spdif
- No device for DAI mxc spdif
- No device for DAI imx-ssi-1-0
- No device for DAI imx-ssi-1-1
- No device for DAI imx-ssi-2-0
- No device for DAI imx-ssi-2-1
- No device for DAI imx-spdif-dai
- DMA Sound Buffer Allocated: Playback UseIram=1 ext_ram=0 buf->addr=f8016000 buf->area=e0856000 size=24576
- DMA Sound Buffer Allocated: Capture UseIram=1 ext_ram=1 buf->addr=cf3d8000 buf->area=fa8ad000 size=24576
- asoc: SGTL5000 <-> imx-ssi-2-0 mapping ok
- mmc0: new high speed SDHC card at address aaaa
- mmcblk0: mmc0:aaaa SU04G 3.69 GiB
- mmcblk0: p1 p2 p3
- DMA Sound Buffer Allocated: Playback UseIram=1 ext_ram=1 buf->addr=cf410000 buf->area=fa8b3000 size=24576
- asoc: mxc spdif <-> imx-spdif-dai mapping ok
- ALSA device list:
- #0: imx-3stack (SGTL5000)
- #1: imx-3stack-spdif (mxc spdif)
- TCP cubic registered
- NET: Registered protocol family 17
- can: controller area network core (rev 20090105 abi 8)
- NET: Registered protocol family 29
- can: raw protocol (rev 20090105)
- can: broadcast manager protocol (rev 20090105 t)
- Bluetooth: L2CAP ver 2.14
- Bluetooth: L2CAP socket layer initialized
- Bluetooth: SCO (Voice Link) ver 0.6
- Bluetooth: SCO socket layer initialized
- Bluetooth: RFCOMM TTY layer initialized
- Bluetooth: RFCOMM socket layer initialized
- Bluetooth: RFCOMM ver 1.11
- Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- Bluetooth: BNEP filters: protocol multicast
- Bluetooth: HIDP (Human Interface Emulation) ver 1.2
- VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
- mxc_rtc mxc_rtc.0: setting system clock to 1970-01-01 00:00:00 UTC (0)
- Root-NFS: No NFS server available, giving up.
- VFS: Unable to mount root fs via NFS, trying floppy.
- VFS: Cannot open root device "(null)" or unknown-block(2,0)
- Please append a correct "root=" boot option; here are the available partitions:
- b300 3872256 mmcblk0 driver: mmcblk
- b301 512 mmcblk0p1
- b302 16384 mmcblk0p2
- b303 3854336 mmcblk0p3
- Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)
- [<80037158>] (unwind_backtrace+0x0/0xe0) from [<803ee744>] (panic+0x68/0xdc)
- [<803ee744>] (panic+0x68/0xdc) from [<80008db8>] (mount_block_root+0x1cc/0x210)
- [<80008db8>] (mount_block_root+0x1cc/0x210) from [<80009030>] (prepare_namespace+0x11c/0x170)
- [<80009030>] (prepare_namespace+0x11c/0x170) from [<80008a24>] (kernel_init+0x120/0x160)
- [<80008a24>] (kernel_init+0x120/0x160) from [<800338b4>] (kernel_thread_exit+0x0/0x8)
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement