Advertisement
Guest User

Untitled

a guest
Apr 5th, 2013
111
0
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 11.78 KB | None | 0 0
  1. root@OpenWrt:/# dmesg
  2. [ 0.000000] Linux version 3.3.8 (dani@tool) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #11 Fri Apr 5 23:57:50 CEST 2013
  3. [ 0.000000] Detected Broadcom 0x6358 CPU revision a1
  4. [ 0.000000] CPU frequency is 300 MHz
  5. [ 0.000000] 64MB of RAM installed
  6. [ 0.000000] registering 40 GPIOs
  7. [ 0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
  8. [ 0.000000] C0 register($16, 0): 0x80008083
  9. [ 0.000000] C0 register($22, 0): 0xe30e1006
  10. [ 0.000000] C0 register($22, 0): 0xe30e1006
  11. [ 0.000000] C0 register($16, 1): 0x3f196c86
  12. [ 0.000000] board_bcm963xx: Boot address 0xbe000000
  13. [ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
  14. [ 0.000000] No bcm_tag found!
  15. [ 0.000000] bootconsole [early0] enabled
  16. [ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
  17. [ 0.000000] board_bcm963xx: board name: HW556_C
  18. [ 0.000000] Determined physical RAM map:
  19. [ 0.000000] memory: 04000000 @ 00000000 (usable)
  20. [ 0.000000] Initrd not found or empty - disabling initrd
  21. [ 0.000000] Zone PFN ranges:
  22. [ 0.000000] Normal 0x00000000 -> 0x00004000
  23. [ 0.000000] Movable zone start PFN for each node
  24. [ 0.000000] Early memory PFN ranges
  25. [ 0.000000] 0: 0x00000000 -> 0x00004000
  26. [ 0.000000] On node 0 totalpages: 16384
  27. [ 0.000000] free_area_init_node: node 0, pgdat 8029f7a0, node_mem_map 81000000
  28. [ 0.000000] Normal zone: 128 pages used for memmap
  29. [ 0.000000] Normal zone: 0 pages reserved
  30. [ 0.000000] Normal zone: 16256 pages, LIFO batch:3
  31. [ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
  32. [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
  33. [ 0.000000] pcpu-alloc: [0] 0
  34. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
  35. [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
  36. [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
  37. [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  38. [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  39. [ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes, 1024 sets per way.
  40. [ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
  41. [ 0.000000] Memory: 61780k/65536k available (2224k kernel code, 3756k reserved, 398k data, 176k init, 0k highmem)
  42. [ 0.000000] NR_IRQS:128
  43. [ 0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
  44. [ 0.036000] pid_max: default: 32768 minimum: 301
  45. [ 0.040000] Mount-cache hash table entries: 512
  46. [ 0.048000] NET: Registered protocol family 16
  47. [ 0.064000] registering PCI controller with io_map_base unset
  48. [ 0.080000] bio: create slab <bio-0> at 0
  49. [ 0.088000] PCI host bridge to bus 0000:00
  50. [ 0.092000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
  51. [ 0.096000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
  52. [ 0.100000] pci 0000:00:01.0: [168c:ff1d] type 0 class 0x000200
  53. [ 0.100000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
  54. [ 0.112000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
  55. [ 0.116000] Switching to clocksource MIPS
  56. [ 0.128000] NET: Registered protocol family 2
  57. [ 0.132000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  58. [ 0.140000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
  59. [ 0.148000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
  60. [ 0.156000] TCP: Hash tables configured (established 2048 bind 2048)
  61. [ 0.160000] TCP reno registered
  62. [ 0.164000] UDP hash table entries: 256 (order: 0, 4096 bytes)
  63. [ 0.172000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  64. [ 0.176000] NET: Registered protocol family 1
  65. [ 0.184000] pci 0000:00:01.0: fixup device configuration
  66. [ 0.192000] PCI: CLS 0 bytes, default 16
  67. [ 0.196000] audit: initializing netlink socket (disabled)
  68. [ 0.200000] type=2000 audit(0.200:1): initialized
  69. [ 0.208000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  70. [ 0.212000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  71. [ 0.224000] msgmni has been set to 120
  72. [ 0.228000] io scheduler noop registered
  73. [ 0.232000] io scheduler deadline registered (default)
  74. [ 0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
  75. [ 0.248000] console [ttyS0] enabled, bootconsole disabled
  76. [ 0.264000] physmap platform flash device: 02000000 at 1e000000
  77. [ 0.272000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
  78. [ 0.280000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
  79. [ 0.280000] Amd/Fujitsu Extended Query Table at 0x0040
  80. [ 0.288000] Amd/Fujitsu Extended Query version 1.3.
  81. [ 0.292000] number of CFI chips: 1
  82. [ 0.296000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
  83. [ 0.304000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
  84. [ 0.312000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
  85. [ 0.316000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length dc0000
  86. [ 0.324000] bcm63xxpart: Partition 3 is cal_data offset ee0000 and length 20000
  87. [ 0.332000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
  88. [ 0.340000] bcm63xxpart: Partition 5 is linux offset 20000 and length ec0000
  89. [ 0.348000] bcm63xxpart: Spare partition is offset 3e0004 and length affffc
  90. [ 0.356000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
  91. [ 0.360000] Creating 6 MTD partitions on "physmap-flash.0":
  92. [ 0.368000] 0x000000000000-0x000000020000 : "CFE"
  93. [ 0.376000] 0x000000020100-0x000000120000 : "kernel"
  94. [ 0.380000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  95. [ 0.396000] 0x000000120000-0x000000ee0000 : "rootfs"
  96. [ 0.404000] mtd: partition "rootfs" set to be root filesystem
  97. [ 0.412000] mtd: partition "rootfs_data" created automatically, ofs=3E0000, len=B00000
  98. [ 0.420000] 0x0000003e0000-0x000000ee0000 : "rootfs_data"
  99. [ 0.428000] 0x000000ee0000-0x000000f00000 : "cal_data"
  100. [ 0.440000] 0x000000fe0000-0x000001000000 : "nvram"
  101. [ 0.448000] 0x000000020000-0x000000ee0000 : "linux"
  102. [ 0.464000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
  103. [ 0.472000] Registered led device: HW556:red:message
  104. [ 0.472000] Registered led device: HW556:red:hspa
  105. [ 0.476000] Registered led device: HW556:red:dsl
  106. [ 0.476000] Registered led device: HW556:red:power
  107. [ 0.476000] Registered led device: HW556:red:all
  108. [ 0.476000] TCP cubic registered
  109. [ 0.480000] NET: Registered protocol family 17
  110. [ 0.484000] 8021q: 802.1Q VLAN Support v1.8
  111. [ 0.496000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  112. [ 0.508000] Freeing unused kernel memory: 176k freed
  113. [ 3.084000] eth0: link forced UP - 100/full - flow control off/off
  114. [ 3.312000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
  115. [ 4.368000] There is already a switch registered on the device 'eth0'
  116. [ 5.788000] Button Hotplug driver version 0.4.1
  117. [ 5.816000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
  118. [ 9.744000] JFFS2 notice: (351) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 9 of xref (0 dead, 2 orphan) found.
  119. [ 12.948000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
  120. [ 12.956000] Backport based on wireless-testing.git master-2012-09-07
  121. [ 12.964000] compat.git: wireless-testing.git
  122. [ 13.020000] cfg80211: Calling CRDA to update world regulatory domain
  123. [ 13.024000] cfg80211: World regulatory domain updated:
  124. [ 13.032000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  125. [ 13.040000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  126. [ 13.048000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  127. [ 13.056000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  128. [ 13.064000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  129. [ 13.072000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  130. [ 13.564000] SCSI subsystem initialized
  131. [ 13.636000] There is already a switch registered on the device 'eth0'
  132. [ 13.856000] usbcore: registered new interface driver usbfs
  133. [ 13.864000] usbcore: registered new interface driver hub
  134. [ 13.872000] usbcore: registered new device driver usb
  135. [ 14.844000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
  136. [ 14.860000] ath: phy0: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
  137. [ 14.868000] ath: phy0: random mac address will be used: 92:e3:2c:88:96:9a
  138. [ 14.876000] ath: EEPROM regdomain: 0x0
  139. [ 14.876000] ath: EEPROM indicates default country code should be used
  140. [ 14.876000] ath: doing EEPROM country->regdmn map search
  141. [ 14.876000] ath: country maps to regdmn code: 0x3a
  142. [ 14.876000] ath: Country alpha2 being used: US
  143. [ 14.876000] ath: Regpair used: 0x3a
  144. [ 14.888000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
  145. [ 14.888000] Registered led device: ath9k-phy0
  146. [ 14.888000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc02c0000, irq=39
  147. [ 14.920000] cfg80211: Calling CRDA for country: US
  148. [ 14.924000] cfg80211: Regulatory domain changed to country: US
  149. [ 14.928000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  150. [ 14.940000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
  151. [ 14.948000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
  152. [ 14.956000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  153. [ 14.964000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  154. [ 14.972000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  155. [ 14.980000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
  156. [ 15.936000] ip_tables: (C) 2000-2006 Netfilter Core Team
  157. [ 16.344000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  158. [ 16.452000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
  159. [ 16.456000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
  160. [ 16.492000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
  161. [ 16.508000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
  162. [ 16.516000] hub 1-0:1.0: USB hub found
  163. [ 16.520000] hub 1-0:1.0: 2 ports detected
  164. [ 16.656000] nf_conntrack version 0.5.0 (968 buckets, 3872 max)
  165. [ 17.080000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
  166. [ 17.316000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  167. [ 17.352000] hub 1-1:1.0: USB hub found
  168. [ 17.360000] hub 1-1:1.0: 2 ports detected
  169. [ 17.424000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
  170. [ 17.428000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
  171. [ 17.436000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
  172. [ 17.504000] hub 2-0:1.0: USB hub found
  173. [ 17.508000] hub 2-0:1.0: 1 port detected
  174. [ 17.696000] Initializing USB Mass Storage driver...
  175. [ 17.704000] usbcore: registered new interface driver usb-storage
  176. [ 17.708000] USB Mass Storage support registered.
  177. [ 21.960000] eth0: link forced UP - 100/full - flow control off/off
  178. [ 21.968000] device eth0 entered promiscuous mode
  179. [ 21.976000] br-lan: port 1(eth0) entered forwarding state
  180. [ 21.980000] br-lan: port 1(eth0) entered forwarding state
  181. [ 23.984000] br-lan: port 1(eth0) entered forwarding state
  182. root@OpenWrt:/#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement