API tools faq
paste
Advertisement
Guest User

Untitled

a guest
May 5th, 2015
263
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 13.89 KB | None | 0 0
raw download clone embed print report
  1. [ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42625) ) #3 Wed Oct 1 14:00:51 CEST 2014
  2. [ 0.000000] MyLoader: sysp=aaaa5554, boardp=aaaa5554, parts=aaaa5554
  3. [ 0.000000] bootconsole [early0] enabled
  4. [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
  5. [ 0.000000] SoC: Atheros AR7161 rev 2
  6. [ 0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.000MHz
  7. [ 0.000000] Determined physical RAM map:
  8. [ 0.000000] memory: 04000000 @ 00000000 (usable)
  9. [ 0.000000] Initrd not found or empty - disabling initrd
  10. [ 0.000000] Zone ranges:
  11. [ 0.000000] Normal [mem 0x00000000-0x03ffffff]
  12. [ 0.000000] Movable zone start for each node
  13. [ 0.000000] Early memory node ranges
  14. [ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
  15. [ 0.000000] On node 0 totalpages: 16384
  16. [ 0.000000] free_area_init_node: node 0, pgdat 80334b60, node_mem_map 81000000
  17. [ 0.000000] Normal zone: 128 pages used for memmap
  18. [ 0.000000] Normal zone: 0 pages reserved
  19. [ 0.000000] Normal zone: 16384 pages, LIFO batch:3
  20. [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  21. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  22. [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
  23. [ 0.000000] pcpu-alloc: [0] 0
  24. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
  25. [ 0.000000] Kernel command line: board=DIR-825-B1 console=ttyS0,115200 mtdparts=spi0.0:256k(uboot)ro,64k(config)ro,6208k(firmware),64k(caldata)ro,1600k(unknown)ro,64k@0x7f0000(caldata_copy) rootfstype=squashfs,jffs2 noinitrd
  26. [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
  27. [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  28. [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  29. [ 0.000000] Writing ErrCtl register=00000000
  30. [ 0.000000] Readback ErrCtl register=00000000
  31. [ 0.000000] Memory: 61076k/65536k available (2369k kernel code, 4460k reserved, 621k data, 272k init, 0k highmem)
  32. [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  33. [ 0.000000] NR_IRQS:51
  34. [ 0.060000] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
  35. [ 0.060000] pid_max: default: 32768 minimum: 301
  36. [ 0.060000] Mount-cache hash table entries: 512
  37. [ 0.070000] NET: Registered protocol family 16
  38. [ 0.070000] MIPS: machine is D-Link DIR-825 rev. B1
  39. [ 0.380000] registering PCI controller with io_map_base unset
  40. [ 2.690000] bio: create slab <bio-0> at 0
  41. [ 2.690000] PCI host bridge to bus 0000:00
  42. [ 2.700000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
  43. [ 2.700000] pci_bus 0000:00: root bus resource [io 0x0000]
  44. [ 2.710000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
  45. [ 2.710000] pci 0000:00:11.0: [168c:ff1d] type 00 class 0x020000
  46. [ 2.710000] pci 0000:00:11.0: fixup device configuration
  47. [ 2.720000] pci 0000:00:11.0: reg 10: [mem 0x00000000-0x0000ffff]
  48. [ 2.720000] pci 0000:00:11.0: PME# supported from D0 D3hot
  49. [ 2.720000] pci 0000:00:12.0: [168c:ff1d] type 00 class 0x020000
  50. [ 2.720000] pci 0000:00:12.0: fixup device configuration
  51. [ 2.720000] pci 0000:00:12.0: reg 10: [mem 0x00000000-0x0000ffff]
  52. [ 2.720000] pci 0000:00:12.0: PME# supported from D0 D3hot
  53. [ 2.720000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
  54. [ 2.720000] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
  55. [ 2.730000] pci 0000:00:12.0: BAR 0: assigned [mem 0x10010000-0x1001ffff]
  56. [ 2.730000] pci 0000:00:11.0: using irq 40 for pin 1
  57. [ 2.740000] pci 0000:00:12.0: using irq 41 for pin 1
  58. [ 2.740000] Switching to clocksource MIPS
  59. [ 2.750000] NET: Registered protocol family 2
  60. [ 2.750000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
  61. [ 2.750000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
  62. [ 2.760000] TCP: Hash tables configured (established 512 bind 512)
  63. [ 2.760000] TCP: reno registered
  64. [ 2.770000] UDP hash table entries: 256 (order: 0, 4096 bytes)
  65. [ 2.770000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  66. [ 2.780000] NET: Registered protocol family 1
  67. [ 2.780000] PCI: CLS 0 bytes, default 32
  68. [ 2.800000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  69. [ 2.800000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  70. [ 2.810000] msgmni has been set to 119
  71. [ 2.820000] io scheduler noop registered
  72. [ 2.820000] io scheduler deadline registered (default)
  73. [ 2.820000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
  74. [ 2.860000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
  75. [ 2.860000] console [ttyS0] enabled, bootconsole disabled
  76. [ 2.880000] ath79-spi ath79-spi: master is unqueued, this is deprecated
  77. [ 2.880000] m25p80 spi0.0: found m25p64, expected m25p80
  78. [ 2.890000] m25p80 spi0.0: m25p64 (8192 Kbytes)
  79. [ 2.890000] 6 cmdlinepart partitions found on MTD device spi0.0
  80. [ 2.900000] Creating 6 MTD partitions on "spi0.0":
  81. [ 2.900000] 0x000000000000-0x000000040000 : "uboot"
  82. [ 2.910000] 0x000000040000-0x000000050000 : "config"
  83. [ 2.920000] 0x000000050000-0x000000660000 : "firmware"
  84. [ 2.930000] 2 uimage-fw partitions found on MTD device firmware
  85. [ 2.930000] 0x000000050000-0x00000015e4db : "kernel"
  86. [ 2.940000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  87. [ 2.950000] 0x00000015e4db-0x000000660000 : "rootfs"
  88. [ 2.960000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  89. [ 2.970000] mtd: device 4 (rootfs) set to be root filesystem
  90. [ 2.980000] 1 squashfs-split partitions found on MTD device rootfs
  91. [ 2.980000] 0x000000380000-0x000000660000 : "rootfs_data"
  92. [ 2.990000] 0x000000660000-0x000000670000 : "caldata"
  93. [ 3.000000] 0x000000670000-0x000000800000 : "unknown"
  94. [ 3.000000] 0x0000007f0000-0x000000800000 : "caldata_copy"
  95. [ 3.010000] Realtek RTL8366S ethernet switch driver version 0.2.2
  96. [ 3.020000] rtl8366s rtl8366s: using GPIO pins 5 (SDA) and 7 (SCK)
  97. [ 3.030000] rtl8366s rtl8366s: RTL8366 ver. 1 chip found
  98. [ 3.050000] rtl8366s rtl8366s: applying initvals
  99. [ 3.060000] libphy: rtl8366s: probed
  100. [ 3.080000] libphy: ag71xx_mdio: probed
  101. [ 3.390000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
  102. [ 3.700000] ag71xx ag71xx.1: connected to PHY at rtl8366s:04 [uid=001cc960, driver=Generic PHY]
  103. [ 3.710000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RGMII
  104. [ 3.720000] TCP: cubic registered
  105. [ 3.720000] NET: Registered protocol family 17
  106. [ 3.720000] Bridge firewalling registered
  107. [ 3.730000] 8021q: 802.1Q VLAN Support v1.8
  108. [ 3.740000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
  109. [ 3.750000] Freeing unused kernel memory: 272K (8034c000 - 80390000)
  110. [ 5.790000] usbcore: registered new interface driver usbfs
  111. [ 5.790000] usbcore: registered new interface driver hub
  112. [ 5.800000] usbcore: registered new device driver usb
  113. [ 5.810000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  114. [ 5.810000] ehci-platform: EHCI generic platform driver
  115. [ 5.820000] ehci-platform ehci-platform: EHCI Host Controller
  116. [ 5.820000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
  117. [ 5.830000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
  118. [ 5.860000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
  119. [ 5.860000] hub 1-0:1.0: USB hub found
  120. [ 5.870000] hub 1-0:1.0: 2 ports detected
  121. [ 5.870000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  122. [ 5.880000] ohci-platform ohci-platform: Generic Platform OHCI Controller
  123. [ 5.890000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
  124. [ 5.890000] ohci-platform ohci-platform: irq 14, io mem 0x1c000000
  125. [ 5.960000] hub 2-0:1.0: USB hub found
  126. [ 5.960000] hub 2-0:1.0: 2 ports detected
  127. [ 6.230000] usb 1-1: new high-speed USB device number 2 using ehci-platform
  128. [ 6.270000] ar71xx: pll_reg 0xb8050010: 0x11110000
  129. [ 6.270000] eth0: link up (1000Mbps/Full duplex)
  130. [ 9.530000] jffs2: notice: (440) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 73 of xref (0 dead, 59 orphan) found.
  131. [ 9.580000] eth0: link down
  132. [ 11.890000] NET: Registered protocol family 10
  133. [ 11.910000] nf_conntrack version 0.5.0 (958 buckets, 3832 max)
  134. [ 11.930000] ip6_tables: (C) 2000-2006 Netfilter Core Team
  135. [ 11.940000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
  136. [ 11.950000] Backport generated by backports.git backports-20140320-37-g5c33da0
  137. [ 11.970000] ip_tables: (C) 2000-2006 Netfilter Core Team
  138. [ 12.010000] usbcore: registered new interface driver usbserial
  139. [ 12.030000] usbcore: registered new interface driver usbserial_generic
  140. [ 12.030000] usbserial: USB Serial support registered for generic
  141. [ 12.080000] xt_time: kernel timezone is -0000
  142. [ 12.100000] cfg80211: Calling CRDA to update world regulatory domain
  143. [ 12.100000] cfg80211: World regulatory domain updated:
  144. [ 12.110000] cfg80211: DFS Master region: unset
  145. [ 12.110000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
  146. [ 12.120000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
  147. [ 12.130000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
  148. [ 12.140000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
  149. [ 12.150000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
  150. [ 12.150000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
  151. [ 12.160000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
  152. [ 12.170000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
  153. [ 12.180000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
  154. [ 12.230000] PPP generic driver version 2.4.2
  155. [ 12.250000] NET: Registered protocol family 24
  156. [ 12.290000] usbcore: registered new interface driver option
  157. [ 12.300000] usbserial: USB Serial support registered for GSM modem (1-port)
  158. [ 12.320000] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
  159. [ 12.330000] ath: EEPROM regdomain: 0x0
  160. [ 12.330000] ath: EEPROM indicates default country code should be used
  161. [ 12.330000] ath: doing EEPROM country->regdmn map search
  162. [ 12.330000] ath: country maps to regdmn code: 0x3a
  163. [ 12.330000] ath: Country alpha2 being used: US
  164. [ 12.330000] ath: Regpair used: 0x3a
  165. [ 12.350000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
  166. [ 12.360000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
  167. [ 12.380000] cfg80211: Calling CRDA for country: US
  168. [ 12.380000] cfg80211: Regulatory domain changed to country: US
  169. [ 12.390000] cfg80211: DFS Master region: FCC
  170. [ 12.390000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
  171. [ 12.400000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
  172. [ 12.410000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
  173. [ 12.420000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
  174. [ 12.420000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
  175. [ 12.430000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
  176. [ 12.440000] PCI: Enabling device 0000:00:12.0 (0000 -> 0002)
  177. [ 12.450000] ath: phy1: eeprom contains invalid mac address: 75:32:b2:43:20:10
  178. [ 12.460000] ath: phy1: random mac address will be used: 7a:fb:ec:14:ff:9b
  179. [ 12.470000] ath: EEPROM regdomain: 0x0
  180. [ 12.470000] ath: EEPROM indicates default country code should be used
  181. [ 12.470000] ath: doing EEPROM country->regdmn map search
  182. [ 12.470000] ath: country maps to regdmn code: 0x3a
  183. [ 12.470000] ath: Country alpha2 being used: US
  184. [ 12.470000] ath: Regpair used: 0x3a
  185. [ 12.570000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
  186. [ 12.570000] ieee80211 phy1: Atheros AR9280 Rev:2 mem=0xb0010000, irq=41
  187. [ 15.230000] rtl8366s rtl8366s: applying initvals
  188. [ 19.060000] ar71xx: pll_reg 0xb8050010: 0x11110000
  189. [ 19.060000] eth0: link up (1000Mbps/Full duplex)
  190. [ 19.070000] device eth0.1 entered promiscuous mode
  191. [ 19.070000] device eth0 entered promiscuous mode
  192. [ 19.080000] br-lan: port 1(eth0.1) entered forwarding state
  193. [ 19.090000] br-lan: port 1(eth0.1) entered forwarding state
  194. [ 20.800000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
  195. [ 20.820000] device wlan0 entered promiscuous mode
  196. [ 20.830000] br-lan: port 2(wlan0) entered forwarding state
  197. [ 20.830000] br-lan: port 2(wlan0) entered forwarding state
  198. [ 20.860000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
  199. [ 20.890000] device wlan1 entered promiscuous mode
  200. [ 20.890000] br-lan: port 3(wlan1) entered forwarding state
  201. [ 20.900000] br-lan: port 3(wlan1) entered forwarding state
  202. [ 21.060000] br-lan: port 2(wlan0) entered disabled state
  203. [ 21.060000] br-lan: port 3(wlan1) entered disabled state
  204. [ 21.090000] br-lan: port 1(eth0.1) entered forwarding state
  205. [ 21.870000] br-lan: port 3(wlan1) entered forwarding state
  206. [ 21.880000] br-lan: port 3(wlan1) entered forwarding state
  207. [ 21.880000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
  208. [ 21.940000] br-lan: port 2(wlan0) entered forwarding state
  209. [ 21.940000] br-lan: port 2(wlan0) entered forwarding state
  210. [ 21.950000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
  211. [ 23.880000] br-lan: port 3(wlan1) entered forwarding state
  212. [ 23.940000] br-lan: port 2(wlan0) entered forwarding state
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!