Dropad A8X Uboot Log

OK


U-Boot 1.3.4-svn (Jun 23 2011 - 09:48:17) for SMDKC110 B Type



CPU:  S5PC110@1000MHz(OK)

        APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz

	MPLL = 667MHz, EPLL = 80MHz

		       HclkDsys = 166MHz, PclkDsys = 83MHz

		       HclkPsys = 133MHz, PclkPsys = 66MHz

		       SCLKA2M  = 200MHz

Serial = CLKUART

Board:   SMDKC110

DRAM:    336 MB

Flash:   1 MB

SD/MMC:  7580 MB

OneNAND:
Muxed OneNAND 512MB 1.8V 16-bit (0x50)

OneNAND version = 0x013e

Scanning device for bad blocks

Bad eraseblock 629 at 0x09d40000

Bad eraseblock 635 at 0x09ec0000

Bad eraseblock 644 at 0x0a100000

Bad eraseblock 666 at 0x0a680000

Bad eraseblock 769 at 0x0c040000

Bad eraseblock 824 at 0x0ce00000

Bad eraseblock 876 at 0x0db00000

Bad eraseblock 879 at 0x0dbc0000

Bad eraseblock 904 at 0x0e200000

OneNAND: 512 MB

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

Partially written block 761 being set for retirement

**>> Block 761 retired

Block 761 is in state 9 after gc, should be erased

------check_poweron is 0!

------check_poweron is 0!

------check_poweron is 0!

------check_poweron good now!


OneNAND read: offset 0x80000, size 0x200000

Main area read (8 blocks):

 2097152 bytes read: OK

*** Warning - using default environment


In:      serial

Out:     serial

Err:     serial

checking mode for fastboot ...

Hit any key to stop autoboot:  0


OneNAND read: offset 0x600000, size 0x400000

Main area read (16 blocks):

 4194304 bytes read: OK


OneNAND read: offset 0xb00000, size 0x180000

Main area read (6 blocks):

 1572864 bytes read: OK

Boot with zImage

get_format

-------- 1 --------

## Loading init Ramdisk from Legacy Image at 30a00000 ...

   Image Name:   ramdisk

   Created:      2011-07-05   3:42:18 UTC

   Image Type:   ARM Linux RAMDisk Image (uncompressed)

   Data Size:    1299203 Bytes =  1.2 MB

   Load Address: 30800000

   Entry Point:  30800000

   Verifying Checksum ... OK


Starting kernel ...


Uncompressing Linux............................................................................................................................................................................................................... done, booting the kernel.
Initializing cgroup subsys cpu
Linux version 2.6.32.9 (root@caixl-desktop) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #397 PREEMPT Mon Jun 20 10:15:23 CST 2011
CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: SMDKC110
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x41001099
Memory policy: ECC disabled, Data cache writeback
  Normal zone: 1 pages exceeds realsize 0
CPU S5PV210/S5PC110 (id 0x43110221)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
mout_mmc: bad source 15
copy: bad source 0
mout_audss: bad source 0
S5PV210: PLL settings, A=1000000000, M=667000000, E=80000000
s5pv210: 37748736 bytes system memory reserved for mfc at 0x30b3e000
s5pv210: 37748736 bytes system memory reserved for mfc at 0x40204000
s5pv210: 14680064 bytes system memory reserved for fimc0 at 0x42604000
s5pv210: 3145728 bytes system memory reserved for fimc1 at 0x43404000
s5pv210: 6291456 bytes system memory reserved for fimc2 at 0x43704000
s5pv210: 5132288 bytes system memory reserved for jpeg at 0x32f3e000
s5pv210: 10485760 bytes system memory reserved for texstream at 0x33423000
s5pv210: 3145728 bytes system memory reserved for fimd at 0x43d04000
s5pv210: 8388608 bytes system memory reserved for g2d at 0x33e23000
Built 3 zonelists in Zone order, mobility grouping on.  Total pages: 121666
Kernel command line: console=ttySAC2,115200 init=/linuxrc no_console_suspend fbcon=rotate:2
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 95MB 256MB 128MB = 479MB total
Memory: 353272KB available (5004K code, 1492K data, 520K init, 0K highmem)
SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=4
Hierarchical RCU implementation.
NR_IRQS:339
VIC @f4000000: id 0x00041192, vendor 0x41
VIC @f4010000: id 0x00041192, vendor 0x41
VIC @f4020000: id 0x00041192, vendor 0x41
vic_pm_register: too few VICs, increase CONFIG_ARM_VIC_NR
VIC @f4030000: id 0x00041192, vendor 0x41
vic_pm_register: too few VICs, increase CONFIG_ARM_VIC_NR
mult[140737]
max_delta_ns[2147483647]
min_delta_ns[30517]
rate[32768]
HZ[256]
Console: colour dummy device 80x30
console [ttySAC2] enabled
Calibrating delay loop... 996.00 BogoMIPS (lpj=1945600)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
S5PC110 Hardware version : EVT1
S3C Power Management, Copyright 2004 Simtec Electronics
S5PV210 Power Domain API Enable
S5PV210: Initializing architecture
s3c24xx-pwm s3c24xx-pwm.0: tin at 4168750, tdiv at 4168750, tin=divclk, base 0
s3c24xx-pwm s3c24xx-pwm.1: tin at 8337500, tdiv at 8337500, tin=divclk, base 8
s3c24xx-pwm s3c24xx-pwm.2: tin at 4168750, tdiv at 4168750, tin=divclk, base 12
s3c24xx-pwm s3c24xx-pwm.3: tin at 4168750, tdiv at 4168750, tin=divclk, base 16
bio: create slab <bio-0> at 0
s3c-i2c s3c2410-i2c.0: slave address 0x10
s3c-i2c s3c2410-i2c.0: bus frequency set to 65 KHz
s3c-i2c s3c2410-i2c.0: i2c-0: S3C I2C adapter
s3c-i2c s3c2410-i2c.1: slave address 0x10
s3c-i2c s3c2410-i2c.1: bus frequency set to 81 KHz
s3c-i2c s3c2410-i2c.1: i2c-1: S3C I2C adapter
s3c-i2c s3c2410-i2c.2: slave address 0x10
s3c-i2c s3c2410-i2c.2: bus frequency set to 65 KHz
s3c-i2c s3c2410-i2c.2: i2c-2: S3C I2C adapter
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Switching to clocksource clock_source_systimer
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 1268K
[ JACK_DRIVER (sec_jack_init,832) ]
SEC JACK: Registering jack driver
input: sec_jack as /devices/virtual/input/input0
[ JACK_DRIVER (sec_jack_probe,701) ] registering switch_sendend switch_dev sysfs sec_jack
[ JACK_DRIVER (detect_irq_handler,407) ] jack isr
[ JACK_DRIVER (detect_irq_handler,407) ] jack isr
[ JACK_DRIVER (sec_jack_probe,758) ] det isr det=0Xbe, ret =0
[ JACK_DRIVER (jack_detect_change,298) ]
JACK dev detached 0
S5PV210 ADC driver, (c) 2010 Samsung Electronics
cpuidle: phy_regs_save:0x359e0000
------------pix_i2c register dev success
Loaded driver for PL330 DMAC-0 s3c-pl330
	DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32
Loaded driver for PL330 DMAC-1 s3c-pl330
	DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
Loaded driver for PL330 DMAC-2 s3c-pl330
	DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
NetWinder Floating Point Emulator V0.97 (extended precision)
ashmem: initialized
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 693
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
i2c /dev entries driver
i2c-gpio i2c-gpio.3: using pins 14 (SDA) and 15 (SCL)
i2c-gpio i2c-gpio.4: using pins 125 (SDA) and 126 (SCL)
i2c-gpio i2c-gpio.12: using pins 18 (SDA) and 19 (SCL)
i2c-gpio i2c-gpio.8: using pins 16 (SDA) and 17 (SCL)
i2c-gpio i2c-gpio.7: using pins 214 (SDA) and 215 (SCL)
i2c-gpio i2c-gpio.9: using pins 212 (SDA) and 213 (SCL)
Linux video capture interface: v2.00
IPC probe success
mfc_init: <6>S5PC110 MFC Driver, (c) 2009 Samsung Electronics

S3C JPEG Driver, (c) 2007 Samsung Electronics
JPEG driver for S5PV210
i2c i2c-1: attached s5p_ddc into i2c adapter successfully
S5PC11X HPD Driver, (c) 2009 Samsung Electronics
S5PC11X CEC Driver, (c) 2009 Samsung Electronics
max8698_ldo_enable[246] ldo 2
regulator: LDO2: 1100 mV
max8698_ldo_enable[246] ldo 3
regulator: LDO3: 1100 mV
max8698_ldo_enable[246] ldo 4
regulator: LDO4: 3300 mV
max8698_ldo_enable[246] ldo 5
regulator: LDO5: 3300 mV
regulator: LDO6: 1800 mV
max8698_ldo_enable[246] ldo 7
regulator: LDO7: 3300 mV
max8698_ldo_enable[246] ldo 8
regulator: LDO8: 3300 mV
regulator: LDO9: 3000 mV
max8698_ldo_enable[246] ldo 10
regulator: BUCK1: 750 <--> 1500 mV
max8698_ldo_enable[246] ldo 11
regulator: BUCK2: 950 <--> 1200 mV
regulator: BUCK3: 1800 mV
	 s3cfb_probe
s3cfb s3cfb: [fb2] dma: 0x43d04000, cpu: 0xe9400000, size: 0x002ee000
fbcon: s3cfb (fb0) is primary device
Console: switching to colour frame buffer device 100x30
FIMD src sclk = 133400000
s3cfb s3cfb: vclk(34635000) should be smaller than 33000000
s3cfb s3cfb: vclk(33350000) should be smaller than 33000000 Hz
parent clock: 133400000, vclk: 33000000, vclk div: 4
s3cfb s3cfb: registered successfully
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
s5pv210-uart.0: s3c2410_serial0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
s5pv210-uart.1: s3c2410_serial1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
s5pv210-uart.2: s3c2410_serial2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
s5pv210-uart.3: s3c2410_serial3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
brd: module loaded
loop: module loaded
Muxed OneNAND 512MB 1.8V 16-bit (0x50)
OneNAND version = 0x013e
Scanning device for bad blocks
onenand_bbt_wait: ecc error = 0xaaaa, controller error 0x0400
Bad eraseblock 629 at 0x09d40000
onenand_bbt_wait: ecc error = 0xaaaa, controller error 0x0400
Bad eraseblock 635 at 0x09ec0000
onenand_bbt_wait: ecc error = 0xaaaa, controller error 0x0400
Bad eraseblock 644 at 0x0a100000
onenand_bbt_wait: ecc error = 0xaaaa, controller error 0x0400
Bad eraseblock 666 at 0x0a680000
onenand_bbt_wait: ecc error = 0xaaaa, controller error 0x0400
Bad eraseblock 761 at 0x0be40000
onenand_bbt_wait: ecc error = 0xaaaa, controller error 0x0400
Bad eraseblock 769 at 0x0c040000
onenand_bbt_wait: ecc error = 0xaaaa, controller error 0x0400
Bad eraseblock 824 at 0x0ce00000
onenand_bbt_wait: ecc error = 0xaaaa, controller error 0x0400
Bad eraseblock 876 at 0x0db00000
onenand_bbt_wait: ecc error = 0xaaaa, controller error 0x0400
Bad eraseblock 879 at 0x0dbc0000
onenand_bbt_wait: ecc error = 0xaaaa, controller error 0x0400
Bad eraseblock 904 at 0x0e200000
Creating 8 MTD partitions on "<NULL>":
0x0000000c0000-0x000000100000 : "misc"
0x000000100000-0x000000600000 : "recovery"
0x000000600000-0x000000b00000 : "kernel"
0x000000b00000-0x000000e00000 : "ramdisk"
0x000000e00000-0x000008600000 : "system"
0x000008600000-0x000009a00000 : "backup"
0x000009a00000-0x00000ea00000 : "cache"
0x00000ea00000-0x000020000000 : "userdata"
PPP generic driver version 2.4.2
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
	 s3c_udc_probe
s3c-udc : S3C HS USB OTG Device Driver, (c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009 (DMA Mode)
android init
android_probe pdata: c05d2280
android_bind
android_usb gadget: android_usb ready
Registered gadget driver 'android_usb'
f_adb init
android_register_function adb
f_mass_storage init
android_register_function usb_mass_storage
mass_storage_bind_config
fsg_probe pdata: c05d22a4
android_usb gadget: Number of LUNs=2
adb_bind_config
mice: PS/2 mouse device common for all mice
input: m3g-keypad as /devices/virtual/input/input1
m3g_keypad_open
release power
input: nastech-tk as /devices/platform/i2c-gpio.3/i2c-3/3-0046/input/input2
---------------nastech_tk_checkonline----success!
nastech IT7235 touchscreen key driver sucess!
input: Goodix-TS as /devices/platform/i2c-gpio.4/i2c-4/4-0055/input/input3
--------------goodix_ts_init_hw success!
Goodix-TS 4-0055:  Guitar Version: GT801_1R06_2011031601_Goodix_Tech
GOODIX GT801 touchscreen driver sucess!
bma150 7-0038: bma150 found
bma150 7-0038: al_version=2, ml_version=1
input: accelerometer as /devices/virtual/input/input4
input: geomagnetic as /devices/platform/i2c-gpio.9/i2c-9/9-002e/input/input5
input: geomagnetic_raw as /devices/platform/i2c-gpio.9/i2c-9/9-002e/input/input6
input: orientation as /devices/virtual/input/input7
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
using rtc device, s3c, for alarms
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
M3G ADC battery Driver probe success!!!
ibcow_init: ibcom ow module init
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
Bluetooth: Virtual HCI driver ver 1.3
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCILL protocol initialized
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz)
MMC e_unknown
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
s3c-sdhci s3c-sdhci.1: clock source 2: sclk_mmc (47642857 Hz)
MMC e_unknown
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
logger: created 64K log 'log_system'
Advanced Linux Sound Architecture Driver Version 1.0.21.
s3c_idma_preallocate_buffer:  VA-e8900000  PA-C0000000  163840bytes
s3c_preallocate_dma_buffer: VA-ff005000, PA-352A0000, 131072bytes
asoc: AK4671 <-> s3c64xx-i2s mapping ok
mmc_rescan mmc0,  search for SDIO
ALSA device list:
  #0: smdkc110 (AK4671)
mmc_rescan mmc0,  search for SD
TCP cubic registered
NET: Registered protocol family 17
Bluetooth: L2CAP ver 2.14
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
OV7670 8-0021: ov7670 has been probed
OV7670 8-0021: fetching platform data
OV7670 8-0021: parallel mode
FIMC0 registered successfully
FIMC1 registered successfully
FIMC2 registered successfully
S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics
s5p-tvout s5p-tvout: hpd status is cable removed
regulator_init_complete: incomplete constraints, leaving VCC_MEM on
regulator_init_complete: incomplete constraints, leaving {VADC/VSYS/VKEY}_2.8V on
regulator_init_complete: incomplete constraints, leaving VCC_1.8V on
regulator_init_complete: incomplete constraints, leaving VMMC_2.8V/VEXT_2.8V on
s3c2410-rtc s3c2410-rtc: setting system clock to 2011-10-22 16:51:15 UTC (1319302275)
Freeing init memory: 520K
mmc0: new high speed SDHC card at address e624
mmcblk0: mmc0:e624 SU08G 7.40 GiB
 mmcblk0: p1
PA FB = 0x43D04000, bits per pixel = 32
screen width=800 height=480 va=0xd3d04000 pa=0x43d04000
Back frameBuffer[0].VAddr=d3e7b000 PAddr=43e7b000 size=1536000
mmc_rescan mmc1,  search for SDIO
mmc_rescan mmc1,  search for SD
mmc_rescan mmc1,  search for MMC
yaffs: dev is 32505860 name is "mtdblock4" rw
yaffs: passed flags ""
yaffs: dev is 32505863 name is "mtdblock7" rw
yaffs: passed flags ""
yaffs: dev is 32505862 name is "mtdblock6" rw
yaffs: passed flags ""
onenand_wait: ECC error = 0xaaaa
onenand_wait: ECC error = 0xaaaa
onenand_wait: ECC error = 0xaaaa
onenand_wait: ECC error = 0xaaaa
onenand_wait: ECC error = 0xaaaa
onenand_wait: ECC error = 0xaaaa
onenand_wait: ECC error = 0xaaaa
onenand_wait: ECC error = 0xaaaa
onenand_wait: ECC error = 0xaaaa
onenand_wait: ECC error = 0xaaaa
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s5pv210-ohci s5pv210-ohci: s5pv210 OHCI
s5pv210-ohci s5pv210-ohci: new USB bus registered, assigned bus number 1
s5pv210-ohci s5pv210-ohci: irq 87, io mem 0xec300000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
sh: can't access tty; job control turned off
# init: cannot find '/system/bin/usb_modeswitch', disabling 'usbmodeswitch'
init: cannot find '/system/bin/3gd', disabling '3gd'
warning: `rild' uses 32-bit capabilities (legacy support in use)
enabling adb
adb_open
PVR_K:(Warning): SysFinalise: Version string: SGX540 S5PC110 [473, services4/system/s5pc110/sysconfig.c]
IIS Audio: 16Bits Stereo 44100Hz
HW Param read reg[0x18] = 0x2
HW Param write reg[0x50] = 0x0
HW Param write reg[0x51] = 0x93
HW Param write reg[0x52] = 0x9
DmaAddr=@c0000000 Total=32768bytes PrdSz=8192 #Prds=4 dma_area=0xe8900000
LOUT3 write reg[0x50] = 0xac
LOUT3 write reg[0x51] = 0xab
LOUT3 write reg[0x52] = 0xab
SND_SOC_AK4671 out3 speaker power down
IIS Audio: 16Bits Stereo 44100Hz
HW Param read reg[0x18] = 0xa
HW Param write reg[0x50] = 0x0
HW Param write reg[0x51] = 0x93
HW Param write reg[0x52] = 0xa9
DmaAddr=@c0000000 Total=32768bytes PrdSz=8192 #Prds=4 dma_area=0xe8900000
LOUT3 write reg[0x50] = 0xac
LOUT3 write reg[0x51] = 0xab
LOUT3 write reg[0x52] = 0xab
SND_SOC_AK4671 out3 speaker power down
s3c-fimc: FIMC2 1 opened.
request_suspend_state: wakeup (3->0) at 18870508540 (2011-10-22 16:51:29.944826315 UTC)
[WIFI] Device powering ON
[WIFI] WIFI_REG_ON = 1
[WIFI] WIFI_RST = 1
MMC e_inserting

Dongle Host Driver, version 4.218.243.1
mmc_rescan mmc1,  search for SDIO
mmc1: new SDIO card at address 0001
DHD: dongle ram size is set to 294912(orig 294912)
Firmware version = wl0: Aug 11 2010 13:21:21 version 4.218.243.1
eth0: Broadcom Dongle Host Driver mac=78:d6:f0:25:f9:af
Enter wl_control_wl_start
Exited wl_control_wl_start
Unkown PRIVATE command, ignored
Unkown PRIVATE command, ignored
Unkown PRIVATE command, ignored
Unkown PRIVATE command, ignored
Unkown PRIVATE command, ignored
Unkown PRIVATE command, ignored
STA connect received 1
Unkown PRIVATE command, ignored
IIS Audio: 16Bits Stereo 44100Hz
HW Param read reg[0x18] = 0xa
HW Param write reg[0x50] = 0x0
HW Param write reg[0x51] = 0x93
HW Param write reg[0x52] = 0xa9
DmaAddr=@c0000000 Total=32768bytes PrdSz=8192 #Prds=4 dma_area=0xe8900000
LOUT3 write reg[0x50] = 0xac
LOUT3 write reg[0x51] = 0xab
LOUT3 write reg[0x52] = 0xab
SND_SOC_AK4671 out3 speaker power down
IIS Audio: 16Bits Stereo 44100Hz
HW Param read reg[0x18] = 0xa
HW Param write reg[0x50] = 0x0
HW Param write reg[0x51] = 0x93
HW Param write reg[0x52] = 0xa9
DmaAddr=@c0000000 Total=32768bytes PrdSz=8192 #Prds=4 dma_area=0xe8900000
LOUT3 write reg[0x50] = 0xac
LOUT3 write reg[0x51] = 0xab
LOUT3 write reg[0x52] = 0xab
SND_SOC_AK4671 out3 speaker power down
press vol up
release vol up
press vol up
IIS Audio: 16Bits Stereo 44100Hz
HW Param read reg[0x18] = 0xa
HW Param write reg[0x50] = 0x0
HW Param write reg[0x51] = 0x93
HW Param write reg[0x52] = 0xa9
DmaAddr=@c0000000 Total=32768bytes PrdSz=8192 #Prds=4 dma_area=0xe8900000
LOUT3 write reg[0x50] = 0xac
LOUT3 write reg[0x51] = 0xab
LOUT3 write reg[0x52] = 0xab
release vol up
press vol up
release vol up
SND_SOC_AK4671 out3 speaker power down
press power
release power
IIS Audio: 16Bits Stereo 44100Hz
HW Param read reg[0x18] = 0xa
HW Param write reg[0x50] = 0x0
HW Param write reg[0x51] = 0x93
HW Param write reg[0x52] = 0xa9
DmaAddr=@c0000000 Total=32768bytes PrdSz=8192 #Prds=4 dma_area=0xe8900000
LOUT3 write reg[0x50] = 0xac
LOUT3 write reg[0x51] = 0xab
LOUT3 write reg[0x52] = 0xab
SND_SOC_AK4671 out3 speaker power down
IIS Audio: 16Bits Stereo 44100Hz
HW Param read reg[0x18] = 0xa
HW Param write reg[0x50] = 0x0
HW Param write reg[0x51] = 0x93
HW Param write reg[0x52] = 0xa9
DmaAddr=@c0000000 Total=32768bytes PrdSz=8192 #Prds=4 dma_area=0xe8900000
LOUT3 write reg[0x50] = 0xac
LOUT3 write reg[0x51] = 0xab
LOUT3 write reg[0x52] = 0xab