# generated by Slic3r 1.2.6 on Sat Feb 28 18:50:58 2015
avoid_crossing_perimeters = 0
bed_shape = 119.343x12.5434,117.378x24.9494,114.127x37.082,109.625x48.8084,103.923x60,97.082x70.5342,89.1774x80.2957,80.2957x89.1774,70.5342x97.082,60x103.923,48.8084x109.625,37.082x114.127,24.9494x117.378,12.5434x119.343,0x120,-12.5434x119.343,-24.9494x117.378,-37.082x114.127,-48.8084x109.625,-60x103.923,-70.5342x97.082,-80.2957x89.1774,-89.1774x80.2957,-97.082x70.5342,-103.923x60,-109.625x48.8084,-114.127x37.082,-117.378x24.9494,-119.343x12.5434,-120x0,-119.343x-12.5434,-117.378x-24.9494,-114.127x-37.082,-109.625x-48.8084,-103.923x-60,-97.082x-70.5342,-89.1774x-80.2957,-80.2957x-89.1774,-70.5342x-97.082,-60x-103.923,-48.8084x-109.625,-37.082x-114.127,-24.9494x-117.378,-12.5434x-119.343,0x-120,12.5434x-119.343,24.9494x-117.378,37.082x-114.127,48.8084x-109.625,60x-103.923,70.5342x-97.082,80.2957x-89.1774,89.1774x-80.2957,97.082x-70.5342,103.923x-60,109.625x-48.8084,114.127x-37.082,117.378x-24.9494,119.343x-12.5434,120x0
bed_temperature = 0
before_layer_gcode =
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 90
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 0
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = M104 S0 ; heat off\nG28 ; home axis\nM84 ; disable motors\nM106 ; FAN BACK ON DAMNIT
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 60%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1.23
extrusion_width = 0
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 45
fill_density = 20%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 0
first_layer_extrusion_width = 0
first_layer_height = 0.25
first_layer_speed = 30%
first_layer_temperature = 210
gap_fill_speed = 40
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 90
interface_shells = 0
layer_gcode =
layer_height = 0.1
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 0
notes =
nozzle_diameter = 0.4
octoprint_apikey =
octoprint_host =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base]_[layer_height].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process =
pressure_advance = 0
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 4.5
retract_length_toolchange = 1
retract_lift = 1
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 100
seam_position = aligned
skirt_distance = 5
skirt_height = 1
skirts = 5
slowdown_below_layer_time = 30
small_perimeter_speed = 60
solid_infill_below_area = 35
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 70
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ;home\nG29 ;probe bed\nG90 ;set absolute coordinates\nM42 P8 S255 ;40mm fan on\nM106 ;30mm fan on
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = honeycomb
support_material_spacing = 2.5
support_material_speed = 90
support_material_threshold = 0
temperature = 210
thin_walls = 1
threads = 6
toolchange_gcode =
top_infill_extrusion_width = 0.2
top_solid_infill_speed = 50
top_solid_layers = 4
travel_speed = 180
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 1
xy_size_compensation = 0
z_offset = -0.08