Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 2015.04-04654-gbcfb33e-dirty (Jun 26 2015 - 12:50:49)
- CPU0: P2020E, Version: 2.1, (0x80ea0021)
- Core: e500, Version: 5.1, (0x80211051)
- Clock Configuration:
- CPU0:1200 MHz, CPU1:1200 MHz,
- CCB:600 MHz,
- DDR:400 MHz (800 MT/s data rate) (Asynchronounfig: 255
- rom_loc: nor upper bank
- SD/MMC : 4-bit Mode
- eSPI : Enabled
- I2C: Error, wrong i2c adapter 2 max 2 possible
- ready
- SPI: ready
- DRAM: Error, wrong i2c adapter 2 max 2 possible
- Detected UDIMM 9905594-009.A00LF
- 2 GiB (DDR3, 64-bit, CL=6, ECC off)
- Flash: 16 MiB
- L2: 512 KiB enabled
- NAND: 256 MiB
- MMC: FSL_SDHC: 0
- *** Warning - bad CRC, using default environment
- PCIe1: Root Complex of mini PCIe SLOT, no link, regs @ 0xffe0a000
- PCIe1: Bus 00 - 00
- PCIe2: Root Complex of PCIe SLOT, x1 gen1, regs @ 0xffe09000
- 02:00.0 - 168c:0030 - Network controller
- PCIe2: Bus 01 - 02
- PCIe3: Root Complex of PCIe SLOT, x1 gen1, regs @ 0xffe08000
- 04:00.0 - 104c:8241 - Serial bus controller
- PCIe3: Bus 03 - 04
- Error, wrong i2c adapter 2 max 2 possible
- In: serial
- Out: serial
- Err: serial
- Net: Phy 5 not found
- PHY reset timed out
- eTSEC1
- Error: eTSEC1 address not set.
- , eTSEC2
- Error: eTSEC2 address not set.
- , eTSEC3 [PRIME]
- Error: eTSEC3 address not set.
- Hit any key to stop autoboot: 1 0
- BOOT NAND
- wdt status 00000003
- UBI: attaching mtd2 to ubi0
- UBI: scanning is finished
- UBI: attached mtd2 (name "mtd=0", size 256 MiB) to ubi0
- UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
- UBI: good PEBs: 2044, bad PEBs: 4, corrupted PEBs: 0
- UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
- UBI: max/mean erase counter: 71/9, WL threshold: 4096, image sequence number: 5942799
- UBI: available PEBs: 0, total reserved PEBs: 2044, PEBs reserved for bad PEB handling: 36
- Loading file '/boot/fdt' to addr 0x02000000 with size 13003 (0x000032cb)...
- Done
- Loading file '/boot/zImage' to addr 0x02100000 with size 2455784 (0x002578e8)...
- Done
- WARNING: adjusting available memory to 30000000
- ## Booting kernel from Legacy Image at 02100000 ...
- Image Name: Linux-3.18.35-dce73e520c6d548378
- Created: 2016-10-26 19:34:16 UTC
- Image Type: PowerPC Linux Kernel Image (gzip compressed)
- Data Size: 2455720 Bytes = 2.3 MiB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 02000000
- Booting using the fdt blob at 0x2000000
- Uncompressing Kernel Image ... OK
- Loading Device Tree to 03ff9000, end 03fff2ca ... OK
- WARNING: could not find compatible node fsl-usb2-dr
- [ 0.000000] Using P2020 RDB machine description
- [ 0.000000] Memory CAM mapping: 256/256 Mb, residual: 1536Mb
- [ 0.000000] Initializing cgroup subsys cpuset
- [ 0.000000] Initializing cgroup subsys cpu
- [ 0.000000] Initializing cgroup subsys cpuacct
- [ 0.000000] Linux version 3.18.35-dce73e520c6d548378632f4054fb5d27-4 (beast@build) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49274) ) #1 SMP Wed Oct 26 21:34:10 CEST 2016
- [ 0.000000] CPU maps initialized for 1 thread per core
- [ 0.000000] bootconsole [udbg0] enabled
- setup_arch: bootmem
- mpc85xx_rdb_setup_arch()
- [ 0.000000] mpc85xx_qe_init: Could not find Quicc Engine node
- [ 0.000000] MPC85xx RDB board from Freescale Semiconductor
- arch: exit
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA [mem 0x00000000-0x1fffffff]
- [ 0.000000] Normal empty
- [ 0.000000] HighMem [mem 0x20000000-0x7fffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x7fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x7fffffff]
- [ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
- [ 0.000000] PERCPU: Embedded 9 pages/cpu @c151e000 s6656 r8192 d22016 u36864
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 523264
- [ 0.000000] Kernel command line: root=ubi0:rootfs rootfstype=ubifs ubi.mtd=9,2048 rootflags=chk_data_crc rw console=ttyS0,115200
- [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000] Sorting __ex_table...
- [ 0.000000] allocated 4194304 bytes of page_cgroup
- [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
- [ 0.000000] Memory: 2004868K/2097152K available (3740K kernel code, 184K rwdata, 820K rodata, 192K init, 243K bss, 92284K reserved, 1572856K highmem)
- [ 0.000000] Kernel virtual memory layout:
- [ 0.000000] * 0xfffbf000..0xfffff000 : fixmap
- [ 0.000000] * 0xffc00000..0xffe00000 : highmem PTEs
- [ 0.000000] * 0xffbfd000..0xffc00000 : early ioremap
- [ 0.000000] * 0xe1000000..0xffbfd000 : vmalloc & ioremap
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:512 nr_irqs:512 16
- [ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs
- [ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff
- [ 0.000000] mpic: Initializing for 256 sources
- [ 0.000000] mpc85xx_rdb_pic_init: Could not find qe-ic node
- [ 0.000008] clocksource: timebase mult[d555555] shift[24] registered
- [ 0.006307] pid_max: default: 32768 minimum: 301
- [ 0.010971] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.017506] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.024934] Initializing cgroup subsys memory
- [ 0.029228] Initializing cgroup subsys devices
- [ 0.033647] Initializing cgroup subsys freezer
- [ 0.038079] Initializing cgroup subsys net_cls
- [ 0.042512] Initializing cgroup subsys blkio
- [ 0.046898] mpic: requesting IPIs...
- [ 0.051306] Brought up 2 CPUs
- [ 0.056672] NET: Registered protocol family 16
- [ 0.066062] cpuidle: using governor ladder
- [ 0.075556] Found FSL PCI host bridge at 0x00000000ffe08000. Firmware bus number: 0->1
- [ 0.083399] PCI host bridge /pcie@ffe08000 (primary) ranges:
- [ 0.089049] MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
- [ 0.096262] IO 0x00000000ffc20000..0x00000000ffc2ffff -> 0x0000000000000000
- [ 0.103398] /pcie@ffe08000: PCICSRBAR @ 0xfff00000
- [ 0.108386] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->1
- [ 0.116225] PCI host bridge /pcie@ffe09000 ranges:
- [ 0.121093] MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
- [ 0.128306] IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000
- [ 0.135441] /pcie@ffe09000: PCICSRBAR @ 0xfff00000
- [ 0.140430] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0
- [ 0.148268] PCI host bridge /pcie@ffe0a000 ranges:
- [ 0.153137] MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000
- [ 0.160350] IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000
- [ 0.167485] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
- [ 0.181278] PCI: Probing PCI hardware
- [ 0.184971] fsl-pci ffe08000.pcie: PCI host bridge to bus 0000:00
- [ 0.190990] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
- [ 0.197155] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xdfffffff]
- [ 0.204023] pci_bus 0000:00: root bus resource [bus 00-ff]
- [ 0.211530] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
- [ 0.216869] fsl-pci ffe09000.pcie: PCI host bridge to bus 0001:02
- [ 0.222888] pci_bus 0001:02: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff])
- [ 0.231836] pci_bus 0001:02: root bus resource [mem 0xa0000000-0xbfffffff]
- [ 0.238703] pci_bus 0001:02: root bus resource [bus 02-ff]
- [ 0.244419] pci 0001:02:00.0: Primary bus is hard wired to 0
- [ 0.250001] pci 0001:02:00.0: bridge configuration invalid ([bus 01-01]), reconfiguring
- [ 0.260018] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
- [ 0.265350] fsl-pci ffe0a000.pcie: PCI host bridge to bus 0002:04
- [ 0.271370] pci_bus 0002:04: root bus resource [io 0x40000-0x4ffff] (bus address [0x0000-0xffff])
- [ 0.280317] pci_bus 0002:04: root bus resource [mem 0x80000000-0x9fffffff]
- [ 0.287186] pci_bus 0002:04: root bus resource [bus 04-ff]
- [ 0.292899] pci 0002:04:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- [ 0.300906] pci 0002:04:00.0: PCI bridge to [bus 05-ff]
- [ 0.306136] PCI: Cannot allocate resource region 0 of PCI bridge 1, will remap
- [ 0.313285] PCI: Cannot allocate resource region 0 of device 0000:00:00.0, will remap
- [ 0.321105] PCI: Cannot allocate resource region 0 of device 0001:02:00.0, will remap
- [ 0.328929] PCI: Cannot allocate resource region 0 of device 0002:04:00.0, will remap
- [ 0.336786] pci 0000:00:00.0: BAR 0: no space for [mem size 0x00100000]
- [ 0.343358] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x00100000]
- [ 0.350312] pci 0000:00:00.0: PCI bridge to [bus 01]
- [ 0.355268] pci 0000:00:00.0: bridge window [mem 0xc0000000-0xdfffffff]
- [ 0.362048] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc
- [ 0.371119] pci 0001:02:00.0: BAR 0: no space for [mem size 0x00100000]
- [ 0.377696] pci 0001:02:00.0: BAR 0: failed to assign [mem size 0x00100000]
- [ 0.384654] pci 0001:03:00.0: BAR 6: assigned [mem 0xa0020000-0xa002ffff pref]
- [ 0.391866] pci 0001:02:00.0: PCI bridge to [bus 03]
- [ 0.396821] pci 0001:02:00.0: bridge window [io 0x20000-0x2ffff]
- [ 0.403080] pci 0001:02:00.0: bridge window [mem 0xa0000000-0xbfffffff]
- [ 0.409861] pci_bus 0001:02: Some PCI device resources are unassigned, try booting with pci=realloc
- [ 0.418939] pci 0002:04:00.0: BAR 0: no space for [mem size 0x00100000]
- [ 0.425510] pci 0002:04:00.0: BAR 0: failed to assign [mem size 0x00100000]
- [ 0.432463] pci 0002:04:00.0: PCI bridge to [bus 05]
- [ 0.437419] pci 0002:04:00.0: bridge window [io 0x40000-0x4ffff]
- [ 0.443678] pci 0002:04:00.0: bridge window [mem 0x80000000-0x9fffffff]
- [ 0.450459] pci_bus 0002:04: Some PCI device resources are unassigned, try booting with pci=realloc
- [ 0.459773] mpic-msgr ffe41400.message: Found 0 message registers
- [ 0.465789] mpic-msgr ffe41400.message: Of-device full name /soc@ffe00000/message@41400
- [ 0.473791] mpic-msgr ffe41400.message: Failed to find message register block alias
- [ 0.490954] Switched to clocksource timebase
- [ 0.495870] NET: Registered protocol family 2
- [ 0.500596] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.507598] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
- [ 0.514044] TCP: Hash tables configured (established 4096 bind 4096)
- [ 0.520399] TCP: reno registered
- [ 0.523567] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.529397] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.535763] NET: Registered protocol family 1
- [ 0.541286] futex hash table entries: 512 (order: 2, 16384 bytes)
- [ 0.552580] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.558353] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.568472] msgmni has been set to 972
- [ 0.572769] bounce: pool size: 64 pages
- [ 0.576579] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
- [ 0.583922] io scheduler noop registered
- [ 0.587828] io scheduler deadline registered (default)
- [ 0.593212] pcieport 0001:02:00.0: enabling device (0106 -> 0107)
- [ 0.599348] pcieport 0002:04:00.0: enabling device (0106 -> 0107)
- [ 0.627087] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.635539] console [ttyS0] disabled
- [ 0.639064] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42, base_baud = 37500000) is a 16550A
- [ 0.647739] console [ttyS0] enabled
- [ 0.647739] console [ttyS0] enabled
- [ 0.654685] bootconsole [udbg0] disabled
- [ 0.654685] bootconsole [udbg0] disabled
- [ 0.662855] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 37500000) is a 16550A
- [ 0.672073] console [ttyS0] disabled
- [ 0.675685] console [ttyS0] enabled
- [ 0.679535] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 37500000) is a 16550
- [ 0.689509] ef000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
- [ 0.699532] Amd/Fujitsu Extended Query Table at 0x0040
- [ 0.704700] Amd/Fujitsu Extended Query version 1.3.
- [ 0.709758] number of CFI chips: 1
- [ 0.713453] 6 ofpart partitions found on MTD device ef000000.nor
- [ 0.719473] Creating 6 MTD partitions on "ef000000.nor":
- [ 0.724793] 0x000000000000-0x000000020000 : "NOR (RO) DTB Image"
- [ 0.731260] 0x000000020000-0x0000001c0000 : "NOR (RO) Linux Kernel Image"
- [ 0.738436] 0x0000001c0000-0x000000340000 : "NOR (RO) JFFS2 Root File System"
- [ 0.745986] 0x000000340000-0x000000e40000 : "NOR (RO) NAND FW backup"
- [ 0.752808] 0x000000e40000-0x000000f00000 : "NOR (RW) Cert backup"
- [ 0.759403] 0x000000f00000-0x000001000000 : "NOR (RO) U-Boot Image"
- [ 0.766569] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
- [ 0.772943] nand: Micron MT29F2G08ABAEAWP
- [ 0.776962] nand: 256MiB, SLC, page size: 2048, OOB size: 64
- [ 0.783975] Bad block table found at page 131008, version 0x01
- [ 0.790560] Bad block table found at page 130944, version 0x01
- [ 0.797087] 4 ofpart partitions found on MTD device ff800000.flash
- [ 0.803279] Creating 4 MTD partitions on "ff800000.flash":
- [ 0.808773] 0x000000000000-0x000000200000 : "NAND (RW) DTB Image"
- [ 0.815323] 0x000000200000-0x000000700000 : "NAND (RW) Linux Kernel Image"
- [ 0.822593] 0x000000700000-0x000010000000 : "NAND (RW) JFFS2 Root File System"
- [ 0.830412] 0x000000000000-0x000010000000 : "rootfs-ubifs"
- [ 0.836473] eLBC NAND device at 0xff800000, bank 1
- [ 0.841659] fsl_espi ffe07000.spi: cs=0, init_csmode=0x100008
- [ 0.847434] fsl_espi ffe07000.spi: cs=1, init_csmode=0x100008
- [ 0.853191] fsl_espi ffe07000.spi: cs=2, init_csmode=0x100008
- [ 0.858946] fsl_espi ffe07000.spi: cs=3, init_csmode=0x100008
- [ 0.864758] fsl_espi ffe07000.spi: master is unqueued, this is deprecated
- [ 0.872392] fsl_espi ffe07000.spi: at 0xe105e000 (irq = 59)
- [ 0.878358] libphy: Fixed MDIO Bus: probed
- [ 0.882639] libphy: Freescale PowerQUICC MII Bus: probed
- [ 0.890487] switch0: Atheros AR8337 rev. 2 switch registered on mdio@ffe24520
- [ 0.941815] fsl-gianfar ffe24000.ethernet: enabled errata workarounds, flags: 0x4
- [ 0.959727] fsl-gianfar ffe24000.ethernet eth0: mac: 00:00:00:00:00:00
- [ 0.966271] fsl-gianfar ffe24000.ethernet eth0: Running with NAPI enabled
- [ 0.973067] fsl-gianfar ffe24000.ethernet eth0: RX BD ring size for Q[0]: 256
- [ 0.980212] fsl-gianfar ffe24000.ethernet eth0: TX BD ring size for Q[0]: 256
- [ 0.987611] fsl-gianfar ffe25000.ethernet: enabled errata workarounds, flags: 0x4
- [ 1.005481] fsl-gianfar ffe25000.ethernet eth1: mac: 00:00:00:00:00:00
- [ 1.012025] fsl-gianfar ffe25000.ethernet eth1: Running with NAPI enabled
- [ 1.018822] fsl-gianfar ffe25000.ethernet eth1: RX BD ring size for Q[0]: 256
- [ 1.025966] fsl-gianfar ffe25000.ethernet eth1: TX BD ring size for Q[0]: 256
- [ 1.033173] fsl-gianfar ffe26000.ethernet: enabled errata workarounds, flags: 0x4
- [ 1.051037] fsl-gianfar ffe26000.ethernet eth2: mac: 00:00:00:00:00:00
- [ 1.057580] fsl-gianfar ffe26000.ethernet eth2: Running with NAPI enabled
- [ 1.064379] fsl-gianfar ffe26000.ethernet eth2: RX BD ring size for Q[0]: 256
- [ 1.071523] fsl-gianfar ffe26000.ethernet eth2: TX BD ring size for Q[0]: 256
- [ 1.078748] ucc_geth_driver: QE UCC Gigabit Ethernet Controller
- [ 1.084881] i2c /dev entries driver
- [ 1.088507] mpc-i2c ffe03000.i2c: timeout 1000000 us
- [ 1.096094] rtc-ds1307 0-006f: rtc core: registered mcp7940x as rtc0
- [ 1.102468] rtc-ds1307 0-006f: 64 bytes nvram
- [ 1.107129] mpc-i2c ffe03100.i2c: timeout 1000000 us
- [ 1.112365] booke_wdt: powerpc book-e watchdog driver loaded
- [ 1.118344] TCP: cubic registered
- [ 1.122019] NET: Registered protocol family 10
- [ 1.127176] NET: Registered protocol family 17
- [ 1.131678] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 1.144322] Bridge firewalling registered
- [ 1.148341] 8021q: 802.1Q VLAN Support v1.8
- [ 1.153592] UBI: attaching mtd9 to ubi0
- [ 2.499713] UBI: scanning is finished
- [ 2.513633] UBI: attached mtd9 (name "rootfs-ubifs", size 256 MiB) to ubi0
- [ 2.520525] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- [ 2.527319] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
- [ 2.533939] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
- [ 2.540819] UBI: good PEBs: 2044, bad PEBs: 4, corrupted PEBs: 0
- [ 2.546830] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
- [ 2.553972] UBI: max/mean erase counter: 71/9, WL threshold: 4096, image sequence number: 5942799
- [ 2.562853] UBI: available PEBs: 0, total reserved PEBs: 2044, PEBs reserved for bad PEB handling: 36
- [ 2.572108] UBI: background thread "ubi_bgt0d" started, PID 943
- [ 2.578979] rtc-ds1307 0-006f: setting system clock to 2016-10-30 13:49:05 UTC (1477835345)
- [ 2.588693] UBIFS: background thread "ubifs_bgt0_0" started, PID 945
- [ 2.641303] UBIFS: recovery needed
- [ 2.752242] UBIFS: recovery completed
- [ 2.755968] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
- [ 2.761992] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
- [ 2.771141] UBIFS: FS size: 252555264 bytes (240 MiB, 1989 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
- [ 2.781071] UBIFS: reserved for root: 0 bytes (0 KiB)
- [ 2.786129] UBIFS: media format: w4/r0 (latest is w4/r0), UUID EF9F9252-45FD-441A-8FED-83ED1E451584, small LPT model
- [ 2.799721] VFS: Mounted root (ubifs filesystem) on device 0:12.
- [ 2.805971] Freeing unused kernel memory: 192K (c0477000 - c04a7000)
- [ 3.018110] init: Console is alive
- [ 3.021629] init: - watchdog -
- [ 3.761310] random: nonblocking pool is initialized
- [ 4.037208] usbcore: registered new interface driver usbfs
- [ 4.042756] usbcore: registered new interface driver hub
- [ 4.048125] usbcore: registered new device driver usb
- [ 4.061794] Button Hotplug driver version 0.4.1
- [ 4.105134] raid6: int32x1 171 MB/s
- [ 4.125057] raid6: int32x2 300 MB/s
- [ 4.145047] raid6: int32x4 414 MB/s
- [ 4.164944] raid6: int32x8 375 MB/s
- [ 4.168694] raid6: using algorithm int32x4 (414 MB/s)
- [ 4.173748] raid6: using intx1 recovery algorithm
- [ 4.179217] xor: measuring software checksum speed
- [ 4.193934] 8regs : 1468.000 MB/sec
- [ 4.207935] 8regs_prefetch: 1308.000 MB/sec
- [ 4.221935] 32regs : 1468.000 MB/sec
- [ 4.235933] 32regs_prefetch: 1352.000 MB/sec
- [ 4.240554] xor: using function: 32regs (1468.000 MB/sec)
- [ 4.523530] Btrfs loaded
- [ 4.744258] JFS: nTxBlock = 8192, nTxLock = 65536
- [ 4.972979] SGI XFS with security attributes, no debug enabled
- [ 5.012969] SCSI subsystem initialized
- [ 5.033656] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 5.040279] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
- [ 5.046920] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
- [ 5.054223] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000
- U-Boot 2015.04-04654-gbcfb33e-dirty (Jun 26 2015 - 12:50:49)
- CPU0: P2020E, Version: 2.1, (0x80ea0021)
- Core: e500, Version: 5.1, (0x80211051)
- Clock Configuration:
- CPU0:1200 MHz, CPU1:1200 MHz,
- CCB:600 MHz,
- DDR:400 MHz (800 MT/s data rate) (Asynchronous), LBC:37.500 MHz
- L1: D-cache 32 KiB enabled
- I-cache 32 KiB enabled
- wdt status 00000005 reset
- Watchdog enabled
- Board: TURRIS CPLD: V4.1 PCBA: V4.0
- Error, wrong i2c adapter 2 max 2 possible
- in: 56
- out: 0
- io_config: 255
- rom_loc: nor upper bank
- SD/MMC : 4-bit Mode
- eSPI : Enabled
- I2C: Error, wrong i2c adapter 2 max 2 possible
- ready
- SPI: ready
- DRAM: Error, wrong i2c adapter 2 max 2 possible
- Detected UDIMM 9905594-009.A00LF
- 2 GiB (DDR3, 64-bit, CL=6, ECC off)
- Flash: 16 MiB
- L2: 512 KiB enabled
- NAND: 256 MiB
- MMC: FSL_SDHC: 0
- *** Warning - bad CRC, using default environment
- PCIe1: Root Complex of mini PCIe SLOT, no link, regs @ 0xffe0a000
- PCIe1: Bus 00 - 00
- PCIe2: Root Complex of PCIe SLOT, x1 gen1, regs @ 0xffe09000
- 02:00.0 - 168c:0030 - Network controller
- PCIe2: Bus 01 - 02
- PCIe3: Root Complex of PCIe SLOT, x1 gen1, regs @ 0xffe08000
- 04:00.0 - 104c:8241 - Serial bus controller
- PCIe3: Bus 03 - 04
- Error, wrong i2c adapter 2 max 2 possible
- In: serial
- Out: serial
- Err: serial
- Net: Phy 5 not found
- PHY reset timed out
- eTSEC1
- Error: eTSEC1 address not set.
- , eTSEC2
- Error: eTSEC2 address not set.
- , eTSEC3 [PRIME]
- Error: eTSEC3 address not set.
- Hit any key to stop autoboot: 1 0
- BOOT NAND
- wdt status 00000003
- UBI: attaching mtd2 to ubi0
- UBI: scanning is finished
- UBI: attached mtd2 (name "mtd=0", size 256 MiB) to ubi0
- UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
- UBI: good PEBs: 2044, bad PEBs: 4, corrupted PEBs: 0
- UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
- UBI: max/mean erase counter: 71/9, WL threshold: 4096, image sequence number: 5942799
- UBI: available PEBs: 0, total reserved PEBs: 2044, PEBs reserved for bad PEB handling: 36
- Loading file '/boot/fdt' to addr 0x02000000 with size 13003 (0x000032cb)...
- Done
- Loading file '/boot/zImage' to addr 0x02100000 with size 2455784 (0x002578e8)...
- Done
- WARNING: adjusting available memory to 30000000
- ## Booting kernel from Legacy Image at 02100000 ...
- Image Name: Linux-3.18.35-dce73e520c6d548378
- Created: 2016-10-26 19:34:16 UTC
- Image Type: PowerPC Linux Kernel Image (gzip compressed)
- Data Size: 2455720 Bytes = 2.3 MiB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 02000000
- Booting using the fdt blob at 0x2000000
- Uncompressing Kernel Image ... OK
- Loading Device Tree to 03ff9000, end 03fff2ca ... OK
- WARNING: could not find compatible node fsl-usb2-dr
- [ 0.000000] Using P2020 RDB machine description
- [ 0.000000] Memory CAM mapping: 256/256 Mb, residual: 1536Mb
- [ 0.000000] Initializing cgroup subsys cpuset
- [ 0.000000] Initializing cgroup subsys cpu
- [ 0.000000] Initializing cgroup subsys cpuacct
- [ 0.000000] Linux version 3.18.35-dce73e520c6d548378632f4054fb5d27-4 (beast@build) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49274) ) #1 SMP Wed Oct 26 21:34:10 CEST 2016
- [ 0.000000] CPU maps initialized for 1 thread per core
- [ 0.000000] bootconsole [udbg0] enabled
- setup_arch: bootmem
- mpc85xx_rdb_setup_arch()
- [ 0.000000] mpc85xx_qe_init: Could not find Quicc Engine node
- [ 0.000000] MPC85xx RDB board from Freescale Semiconductor
- arch: exit
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA [mem 0x00000000-0x1fffffff]
- [ 0.000000] Normal empty
- [ 0.000000] HighMem [mem 0x20000000-0x7fffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x7fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x7fffffff]
- [ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
- [ 0.000000] PERCPU: Embedded 9 pages/cpu @c151e000 s6656 r8192 d22016 u36864
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 523264
- [ 0.000000] Kernel command line: root=ubi0:rootfs rootfstype=ubifs ubi.mtd=9,2048 rootflags=chk_data_crc rw console=ttyS0,115200
- [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000] Sorting __ex_table...
- [ 0.000000] allocated 4194304 bytes of page_cgroup
- [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
- [ 0.000000] Memory: 2004868K/2097152K available (3740K kernel code, 184K rwdata, 820K rodata, 192K init, 243K bss, 92284K reserved, 1572856K highmem)
- [ 0.000000] Kernel virtual memory layout:
- [ 0.000000] * 0xfffbf000..0xfffff000 : fixmap
- [ 0.000000] * 0xffc00000..0xffe00000 : highmem PTEs
- [ 0.000000] * 0xffbfd000..0xffc00000 : early ioremap
- [ 0.000000] * 0xe1000000..0xffbfd000 : vmalloc & ioremap
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:512 nr_irqs:512 16
- [ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs
- [ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff
- [ 0.000000] mpic: Initializing for 256 sources
- [ 0.000000] mpc85xx_rdb_pic_init: Could not find qe-ic node
- [ 0.000007] clocksource: timebase mult[d555555] shift[24] registered
- [ 0.006306] pid_max: default: 32768 minimum: 301
- [ 0.010970] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.017505] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.024932] Initializing cgroup subsys memory
- [ 0.029225] Initializing cgroup subsys devices
- [ 0.033644] Initializing cgroup subsys freezer
- [ 0.038075] Initializing cgroup subsys net_cls
- [ 0.042509] Initializing cgroup subsys blkio
- [ 0.046897] mpic: requesting IPIs...
- [ 0.051303] Brought up 2 CPUs
- [ 0.056665] NET: Registered protocol family 16
- [ 0.066053] cpuidle: using governor ladder
- [ 0.075559] Found FSL PCI host bridge at 0x00000000ffe08000. Firmware bus number: 0->1
- [ 0.083403] PCI host bridge /pcie@ffe08000 (primary) ranges:
- [ 0.089052] MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
- [ 0.096265] IO 0x00000000ffc20000..0x00000000ffc2ffff -> 0x0000000000000000
- [ 0.103400] /pcie@ffe08000: PCICSRBAR @ 0xfff00000
- [ 0.108390] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->1
- [ 0.116229] PCI host bridge /pcie@ffe09000 ranges:
- [ 0.121097] MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
- [ 0.128311] IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000
- [ 0.135446] /pcie@ffe09000: PCICSRBAR @ 0xfff00000
- [ 0.140436] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0
- [ 0.148274] PCI host bridge /pcie@ffe0a000 ranges:
- [ 0.153142] MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000
- [ 0.160356] IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000
- [ 0.167491] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
- [ 0.181294] PCI: Probing PCI hardware
- [ 0.184986] fsl-pci ffe08000.pcie: PCI host bridge to bus 0000:00
- [ 0.191006] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
- [ 0.197170] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xdfffffff]
- [ 0.204039] pci_bus 0000:00: root bus resource [bus 00-ff]
- [ 0.211544] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
- [ 0.216882] fsl-pci ffe09000.pcie: PCI host bridge to bus 0001:02
- [ 0.222901] pci_bus 0001:02: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff])
- [ 0.231849] pci_bus 0001:02: root bus resource [mem 0xa0000000-0xbfffffff]
- [ 0.238716] pci_bus 0001:02: root bus resource [bus 02-ff]
- [ 0.244432] pci 0001:02:00.0: Primary bus is hard wired to 0
- [ 0.250015] pci 0001:02:00.0: bridge configuration invalid ([bus 01-01]), reconfiguring
- [ 0.260031] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
- [ 0.265364] fsl-pci ffe0a000.pcie: PCI host bridge to bus 0002:04
- [ 0.271383] pci_bus 0002:04: root bus resource [io 0x40000-0x4ffff] (bus address [0x0000-0xffff])
- [ 0.280331] pci_bus 0002:04: root bus resource [mem 0x80000000-0x9fffffff]
- [ 0.287199] pci_bus 0002:04: root bus resource [bus 04-ff]
- [ 0.292915] pci 0002:04:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- [ 0.300921] pci 0002:04:00.0: PCI bridge to [bus 05-ff]
- [ 0.306152] PCI: Cannot allocate resource region 0 of PCI bridge 1, will remap
- [ 0.313302] PCI: Cannot allocate resource region 0 of device 0000:00:00.0, will remap
- [ 0.321121] PCI: Cannot allocate resource region 0 of device 0001:02:00.0, will remap
- [ 0.328945] PCI: Cannot allocate resource region 0 of device 0002:04:00.0, will remap
- [ 0.336802] pci 0000:00:00.0: BAR 0: no space for [mem size 0x00100000]
- [ 0.343375] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x00100000]
- [ 0.350329] pci 0000:00:00.0: PCI bridge to [bus 01]
- [ 0.355284] pci 0000:00:00.0: bridge window [mem 0xc0000000-0xdfffffff]
- [ 0.362065] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc
- [ 0.371135] pci 0001:02:00.0: BAR 0: no space for [mem size 0x00100000]
- [ 0.377713] pci 0001:02:00.0: BAR 0: failed to assign [mem size 0x00100000]
- [ 0.384670] pci 0001:03:00.0: BAR 6: assigned [mem 0xa0020000-0xa002ffff pref]
- [ 0.391883] pci 0001:02:00.0: PCI bridge to [bus 03]
- [ 0.396837] pci 0001:02:00.0: bridge window [io 0x20000-0x2ffff]
- [ 0.403097] pci 0001:02:00.0: bridge window [mem 0xa0000000-0xbfffffff]
- [ 0.409878] pci_bus 0001:02: Some PCI device resources are unassigned, try booting with pci=realloc
- [ 0.418956] pci 0002:04:00.0: BAR 0: no space for [mem size 0x00100000]
- [ 0.425526] pci 0002:04:00.0: BAR 0: failed to assign [mem size 0x00100000]
- [ 0.432480] pci 0002:04:00.0: PCI bridge to [bus 05]
- [ 0.437435] pci 0002:04:00.0: bridge window [io 0x40000-0x4ffff]
- [ 0.443694] pci 0002:04:00.0: bridge window [mem 0x80000000-0x9fffffff]
- [ 0.450475] pci_bus 0002:04: Some PCI device resources are unassigned, try booting with pci=realloc
- [ 0.459788] mpic-msgr ffe41400.message: Found 0 message registers
- [ 0.465804] mpic-msgr ffe41400.message: Of-device full name /soc@ffe00000/message@41400
- [ 0.473806] mpic-msgr ffe41400.message: Failed to find message register block alias
- [ 0.490972] Switched to clocksource timebase
- [ 0.495887] NET: Registered protocol family 2
- [ 0.500615] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.507616] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
- [ 0.514058] TCP: Hash tables configured (established 4096 bind 4096)
- [ 0.520417] TCP: reno registered
- [ 0.523587] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.529415] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.535779] NET: Registered protocol family 1
- [ 0.541304] futex hash table entries: 512 (order: 2, 16384 bytes)
- [ 0.552605] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.558377] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.568497] msgmni has been set to 972
- [ 0.572793] bounce: pool size: 64 pages
- [ 0.576600] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
- [ 0.583945] io scheduler noop registered
- [ 0.587850] io scheduler deadline registered (default)
- [ 0.593236] pcieport 0001:02:00.0: enabling device (0106 -> 0107)
- [ 0.599369] pcieport 0002:04:00.0: enabling device (0106 -> 0107)
- [ 0.627116] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.635573] console [ttyS0] disabled
- [ 0.639099] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42, base_baud = 37500000) is a 16550A
- [ 0.647775] console [ttyS0] enabled
- [ 0.647775] console [ttyS0] enabled
- [ 0.654720] bootconsole [udbg0] disabled
- [ 0.654720] bootconsole [udbg0] disabled
- [ 0.662889] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 37500000) is a 16550A
- [ 0.672111] console [ttyS0] disabled
- [ 0.675724] console [ttyS0] enabled
- [ 0.679578] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 37500000) is a 16550
- [ 0.689550] ef000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
- [ 0.699573] Amd/Fujitsu Extended Query Table at 0x0040
- [ 0.704741] Amd/Fujitsu Extended Query version 1.3.
- [ 0.709800] number of CFI chips: 1
- [ 0.713508] 6 ofpart partitions found on MTD device ef000000.nor
- [ 0.719528] Creating 6 MTD partitions on "ef000000.nor":
- [ 0.724848] 0x000000000000-0x000000020000 : "NOR (RO) DTB Image"
- [ 0.731317] 0x000000020000-0x0000001c0000 : "NOR (RO) Linux Kernel Image"
- [ 0.738495] 0x0000001c0000-0x000000340000 : "NOR (RO) JFFS2 Root File System"
- [ 0.746047] 0x000000340000-0x000000e40000 : "NOR (RO) NAND FW backup"
- [ 0.752872] 0x000000e40000-0x000000f00000 : "NOR (RW) Cert backup"
- [ 0.759465] 0x000000f00000-0x000001000000 : "NOR (RO) U-Boot Image"
- [ 0.766637] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
- [ 0.773006] nand: Micron MT29F2G08ABAEAWP
- [ 0.777026] nand: 256MiB, SLC, page size: 2048, OOB size: 64
- [ 0.784034] Bad block table found at page 131008, version 0x01
- [ 0.790621] Bad block table found at page 130944, version 0x01
- [ 0.797149] 4 ofpart partitions found on MTD device ff800000.flash
- [ 0.803345] Creating 4 MTD partitions on "ff800000.flash":
- [ 0.808844] 0x000000000000-0x000000200000 : "NAND (RW) DTB Image"
- [ 0.815391] 0x000000200000-0x000000700000 : "NAND (RW) Linux Kernel Image"
- [ 0.822660] 0x000000700000-0x000010000000 : "NAND (RW) JFFS2 Root File System"
- [ 0.830477] 0x000000000000-0x000010000000 : "rootfs-ubifs"
- [ 0.836536] eLBC NAND device at 0xff800000, bank 1
- [ 0.841727] fsl_espi ffe07000.spi: cs=0, init_csmode=0x100008
- [ 0.847506] fsl_espi ffe07000.spi: cs=1, init_csmode=0x100008
- [ 0.853263] fsl_espi ffe07000.spi: cs=2, init_csmode=0x100008
- [ 0.859017] fsl_espi ffe07000.spi: cs=3, init_csmode=0x100008
- [ 0.864833] fsl_espi ffe07000.spi: master is unqueued, this is deprecated
- [ 0.872467] fsl_espi ffe07000.spi: at 0xe105e000 (irq = 59)
- [ 0.878424] libphy: Fixed MDIO Bus: probed
- [ 0.882705] libphy: Freescale PowerQUICC MII Bus: probed
- [ 0.890534] switch0: Atheros AR8337 rev. 2 switch registered on mdio@ffe24520
- [ 0.941837] fsl-gianfar ffe24000.ethernet: enabled errata workarounds, flags: 0x4
- [ 0.959749] fsl-gianfar ffe24000.ethernet eth0: mac: 00:00:00:00:00:00
- [ 0.966292] fsl-gianfar ffe24000.ethernet eth0: Running with NAPI enabled
- [ 0.973089] fsl-gianfar ffe24000.ethernet eth0: RX BD ring size for Q[0]: 256
- [ 0.980234] fsl-gianfar ffe24000.ethernet eth0: TX BD ring size for Q[0]: 256
- [ 0.987631] fsl-gianfar ffe25000.ethernet: enabled errata workarounds, flags: 0x4
- [ 1.005502] fsl-gianfar ffe25000.ethernet eth1: mac: 00:00:00:00:00:00
- [ 1.012045] fsl-gianfar ffe25000.ethernet eth1: Running with NAPI enabled
- [ 1.018841] fsl-gianfar ffe25000.ethernet eth1: RX BD ring size for Q[0]: 256
- [ 1.025985] fsl-gianfar ffe25000.ethernet eth1: TX BD ring size for Q[0]: 256
- [ 1.033194] fsl-gianfar ffe26000.ethernet: enabled errata workarounds, flags: 0x4
- [ 1.051054] fsl-gianfar ffe26000.ethernet eth2: mac: 00:00:00:00:00:00
- [ 1.057598] fsl-gianfar ffe26000.ethernet eth2: Running with NAPI enabled
- [ 1.064396] fsl-gianfar ffe26000.ethernet eth2: RX BD ring size for Q[0]: 256
- [ 1.071541] fsl-gianfar ffe26000.ethernet eth2: TX BD ring size for Q[0]: 256
- [ 1.078765] ucc_geth_driver: QE UCC Gigabit Ethernet Controller
- [ 1.084896] i2c /dev entries driver
- [ 1.088523] mpc-i2c ffe03000.i2c: timeout 1000000 us
- [ 1.096113] rtc-ds1307 0-006f: rtc core: registered mcp7940x as rtc0
- [ 1.102487] rtc-ds1307 0-006f: 64 bytes nvram
- [ 1.107151] mpc-i2c ffe03100.i2c: timeout 1000000 us
- [ 1.112385] booke_wdt: powerpc book-e watchdog driver loaded
- [ 1.118365] TCP: cubic registered
- [ 1.122040] NET: Registered protocol family 10
- [ 1.127193] NET: Registered protocol family 17
- [ 1.131697] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 1.144340] Bridge firewalling registered
- [ 1.148359] 8021q: 802.1Q VLAN Support v1.8
- [ 1.153604] UBI: attaching mtd9 to ubi0
- [ 2.499743] UBI: scanning is finished
- [ 2.513658] UBI: attached mtd9 (name "rootfs-ubifs", size 256 MiB) to ubi0
- [ 2.520550] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- [ 2.527345] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
- [ 2.533965] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
- [ 2.540845] UBI: good PEBs: 2044, bad PEBs: 4, corrupted PEBs: 0
- [ 2.546856] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
- [ 2.553998] UBI: max/mean erase counter: 71/9, WL threshold: 4096, image sequence number: 5942799
- [ 2.562879] UBI: available PEBs: 0, total reserved PEBs: 2044, PEBs reserved for bad PEB handling: 36
- [ 2.572134] UBI: background thread "ubi_bgt0d" started, PID 943
- [ 2.579001] rtc-ds1307 0-006f: setting system clock to 2016-10-30 13:49:57 UTC (1477835397)
- [ 2.588709] UBIFS: background thread "ubifs_bgt0_0" started, PID 945
- [ 2.641323] UBIFS: recovery needed
- [ 2.752261] UBIFS: recovery completed
- [ 2.755988] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
- [ 2.762012] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
- [ 2.771161] UBIFS: FS size: 252555264 bytes (240 MiB, 1989 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
- [ 2.781092] UBIFS: reserved for root: 0 bytes (0 KiB)
- [ 2.786149] UBIFS: media format: w4/r0 (latest is w4/r0), UUID EF9F9252-45FD-441A-8FED-83ED1E451584, small LPT model
- [ 2.799742] VFS: Mounted root (ubifs filesystem) on device 0:12.
- [ 2.805990] Freeing unused kernel memory: 192K (c0477000 - c04a7000)
- [ 3.018158] init: Console is alive
- [ 3.021678] init: - watchdog -
- [ 3.762021] random: nonblocking pool is initialized
- [ 4.037277] usbcore: registered new interface driver usbfs
- [ 4.042825] usbcore: registered new interface driver hub
- [ 4.048194] usbcore: registered new device driver usb
- [ 4.061843] Button Hotplug driver version 0.4.1
- [ 4.105152] raid6: int32x1 171 MB/s
- [ 4.125074] raid6: int32x2 300 MB/s
- [ 4.145062] raid6: int32x4 414 MB/s
- [ 4.164960] raid6: int32x8 375 MB/s
- [ 4.168710] raid6: using algorithm int32x4 (414 MB/s)
- [ 4.173764] raid6: using intx1 recovery algorithm
- [ 4.179229] xor: measuring software checksum speed
- [ 4.193952] 8regs : 1468.000 MB/sec
- [ 4.207953] 8regs_prefetch: 1308.000 MB/sec
- [ 4.221952] 32regs : 1468.000 MB/sec
- [ 4.235951] 32regs_prefetch: 1352.000 MB/sec
- [ 4.240571] xor: using function: 32regs (1468.000 MB/sec)
- [ 4.524224] Btrfs loaded
- [ 4.745276] JFS: nTxBlock = 8192, nTxLock = 65536
- [ 4.974450] SGI XFS with security attributes, no debug enabled
- [ 5.014476] SCSI subsystem initialized
- [ 5.035172] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 5.041795] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
- [ 5.048435] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
- [ 5.055734] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement