Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- ----------------------- Page 1-----------------------
- Fuel from 'Burning Water'
- provided by The Reclamation Project
- *** Working Plans ***
- 01/09/02
- UltimateMallStore Disclaimer: We have indication these plans work when built, but
- every person is unique this depends on your ability to make it work, also we are not
- responsible for any accidents or injuries, etc so please be careful ,if you choose to try it,
- use common sense and start SMALL, like a lawnmower engine, please report any
- successes you might have.
- The following file was received by Dave the Gravman via FAX, he kindly sent it to me,
- thanks Dave!
- • Convert your engine to burn hydrogen & oxygen
- • Make vapour from water on demand & pollution-free
- • Convert your vehicle to a ZPV: Zero Pollution Vehicle
- • Freedom from Gasoline
- • Simple and inexpensive conversion
- • On Demand vapour rate via throttle
- • Easy do it yourself public domain plans
- • Help clean the air while you save money
- These plans can be used to run your car, truck, RV, motorcycle, airplane, etc. from tap
- water.
- ----------------------- Page 2-----------------------
- Are you fed up with ga$oline price$ and THE POLLUTION?
- Would you like to do something about it besides complain and wait?
- Are you still CHOKING on the whole idea of fossil fuel CON$UMPTION? WHY?
- Wouldn't you like to free yourself from centrally-controlled or imported fuel?
- Do you have a 2nd vehicle you don't use every day?
- Now there is something we can actually do about it, as individuals willing to help clean
- the environment, and travel at lower cost to both you and your environment. Do-it-
- yourself plans allow the individual (that's you and me, folks) to make a difference.
- This is the easiest and lowest cost way to convert your car to run on (relatively) free
- energy. Now with existing technology, anyone can stand up and make a difference by
- reducing the local automotive pollution, eliminate ga$oline expen$e$, help restore our
- atmosphere, and breathe a little easier. You will be making use of your entire existing
- system, except the fuel tank and catalytic converter.
- THE PLAN:
- Know the Truth and set yourself FREE. Set a good example for the World you choose to
- create. Exercise your own Free Will. Live cleaner and healthier.
- Build and install a low-cost alternative method for running your vehicle (internal
- combustion) engine on TAP WATER, using off-the-shelf components. This is simply an
- efficient way to convert ordinary tap water into gaseous Hydrogen and Oxygen, and then
- burn these vapours in the engine, instead of that $melly, $tinky, expen$ive 'other $tuff.
- This 'minisystem' runs easily from your existing battery and electrical system, and it
- plugs into your carburetor with simple off-the-shelf fittings. You will be installing a
- plastic water tank, a control circuit, a reaction chamber, a hi-pressure carb/FI fitting, and
- 3 gauges (see Figure 1), and then hooking into your existing carb/FI.
- The SIMPLICITY comes from being an 'on-demand' system requiring no fancy storage,
- or plumbing. You crank the gas pedal or throttle and you electrically create more vapour
- for immediate consumption, on demand; Lo - Hi Flow Rate as needed from idle - max
- power. The only real change is that you are using tap water as fuel, instead of the
- traditional petroleum-based fuel. Given, a choice, which way would you choose?
- FAQs
- Q: Does it really work?
- ----------------------- Page 3-----------------------
- A: Yes; this is well-established technology dating back to stainless steel. But be sure to
- follow these instructions using the proper mechanical and electrical assembly techniques,
- as it incorporates the best qualities of several techniques.
- Q: How does it qualify as 'free energy'?
- A: If you're paying someone for the water you use, then it is not strictly 'free'. But, the
- alternative is to keep buying into the expen$ive ga$oline and re$ultant hydrocarbon
- pollution.
- Q: Is it Safe?
- A: Technically, it is safer than running on fossil fuel, because you are no longer choking
- on your own emissions (health-wise), but in general it is practically as safe as your current
- gasoline arrangement. You will be installing a few simple safety devices, using current
- automotive standards.
- Q: What kind of performance can I expect?
- A: Properly adjusted, your modified vapour-only fuel system will run cooler, and at a
- modestly higher power level. The mileage performance expected from this design ranges
- from 50-300 mpg, depending on your adjusting skills.
- Q: Can I do the modification myself?
- A: Why not? If you know someone with basic mechanical and/or electrical skills, you can
- even delegate some of the construction. If you are using a fuel-injected engine, you may
- have to get a mechanic's opinion.
- 0: What is the environmental impact that my vehicle will have?
- A: It will be producing H20 steam and unburnt 02, hence it will be cleaning the
- environment, rather than dumping nauseous toxins into it. Plus you will be helping to
- save our dwindling supply of atmospheric oxygen. Any excess vapour in the reaction
- becomes either steam or oxygen. You can also expect to be receiving more than casual
- interest from those around you.
- Q: Is this really a steam engine?
- A: No; really. Exceedingly hi temp & pressure are not used. This is strictly an internal
- combustion engine (burning orthohydrogen) with residual steam in the exhaust as a by
- product.
- Gasoline as a fuel is NOT NECESSARY; it is optional.
- 1. ORIGIN - In the 19th century, the gasoline portion of the refining process, was first
- considered to be a 'waste' product of extracting the purified crude oil. Later on, it was
- ----------------------- Page 4-----------------------
- discovered that it could be $old as fuel, instead of just dumping it back in the hole as had
- been the tradition.
- 2. CONSUMPTION RATE - The gasoline consumption rate for every mass-produced car
- has been carefully 'designed in' as a market asset. As an indication, simply observe how
- quickly and closely ALL the local different gas stations adjust their prices. Even the
- hybrid cars which use electric motors still consume a designed amount of gasoline, and
- their price tags are prohibitively high.
- 3. EFFICIENCY - There is a lot of thermo-chemical energy in gasoline, but there is even
- more energy in water. The DOE has quoted about 40%, 50 it is probably much more than
- that. Most people are unaware that 'internal combustion' is DEFINED as: a thermo-
- vapour process; as in 'no liquid in the reaction'; AND most of the gasoline in a standard
- internal combustion engine, is ACTUALLY CONSUMED cooked and finally broken
- down) IN THE CATALYTIC CONVERTER, which happens AFTER the fuel has been
- not-so-burnt in the engine. Sadly, this means that most of the fuel we use in this way, is
- used only to cool down the combustion process, rather than using a cleaner and more
- efficient means to do so.
- 4. ADDITIVES - Also sadly, we are told by 'authorities' that some of the many gasoline
- additives are in the mix to increase performance; but because of its current overly-
- complex molecular structure, the real built-in function of the gasoline formula is to slow
- down the combustion so that only so much is actually consumed in the cylinder, and the
- liquid balance goes to the catalytic converter. As a further insult, the additives are also
- there to clog and prevent the use of the Pogue-style carburetors, designed to get 200-300
- mpg.
- 5. PROFIT - Is the Pope catholic? does the bear poop in the woods? Of course the oil
- companies are making a huge profit. It is by design. What do you suppose the Gulf War
- was about? Just look at where the crude oil comes from and where the money is flowing.
- Rest assured that the oil companies do NOT want you to know how to make use of this
- water-fuel technology. They have been making money on our ignorance, dis-
- empowerment, and willingness to follow along in a mindless 'comfort-zone' of toxic waste,
- suppression, resentment, and apathy: WHO NEEDS IT?
- Let us proceed to set a good example and do it right, do it clean.
- Exceedingly simple
- Water is pumped as needed to replenish and maintain the liquid level in the chamber.
- The electrodes are vibrated with a 0.5-SA electrical pulse which breaks 2(H20) --- ( 2H2 +
- 02 ).
- When the pressure reaches say 30-60 psi, you turn the key and go. You step on the pedal,
- you send more energy to the electrodes, and thus more vapour to the cylinders; i.e. fuel
- vapour on demand.
- You set the idle - max flow rate to get the most efficient use of power, and you're off to the
- races.
- ----------------------- Page 5-----------------------
- In the BIG picture, your Free Energy is coming from the tap water, in an open system, as
- the latent energy in the water is enough to power the engine, and hence drive the
- alternator and whatever belt-driven accessories; AND the alternator is efficient enough to
- run the various electrical loads (10-20 amps), including the additional low current to run
- this vapour reaction. No extra batteries are required.
- ----------------------- Page 6-----------------------
- ----------------------- Page 7-----------------------
- OVERVIEW - Here is the suggested sequence of steps:
- 1. Install the CHT (or EGT) gauge and measure your current operating temp range
- (gasoline), for comparison.
- 2. Build & test the controller to verify the correct pulse output.
- 3. Build the reaction chamber & test it w. the controller (i.e pressure out).
- 4. Install the tank, controller, chamber, and pressure fittings.
- 5. Run engine & Adjust the control circuit as necessary for best performance.
- 6. Install the stainless steel valves and get the pistons/cylinders coated with ceramic.
- 7. Coat the exhaust system with ceramic without the catalytic converter OR let it rust out
- and replace the whole dang thang with stainless steel pipe sections.
- YOU WILL NEED:
- • - plastic water tank with pump and level sensor.
- • - control circuit, wiring, connectors, and epoxy.
- • - reaction chamber with electrodes and fittings.
- • - 3/8" stainless steel flex-tubing, fittings and clamps.- carb/FI vapor-pressure
- fitting kit. - pressure, CHT (or EGT), & level gauges.
- • - stainless steel valves.
- • - copper mesh junction.
- • - ceramic surface treatment for cylinders & pistons.
- • - stainless steel or ceramic treated exhaust assembly.
- BASIC TOOLS
- • - drill, screwdriver and pliers
- • - hole cutter
- • - wire-wrap, solder-iron and clippers
- • - DVM and oscilloscope.
- REACTION CHAMBER
- Construct as shown in Figure 2. Use a section of 4" PVC waste pipe with a threaded
- screw-cap fitting on one end and a standard end-cap at the other.
- ----------------------- Page 8-----------------------
- Make sure to drill-and-epoxy or tap threads through the PVC components for all fittings.
- Set and control the water level in the chamber so that it well submerses the pipe
- electrodes; yet leave some headroom to build up the hydrogen/oxygen vapour pressure.
- Use stainless steel wires inside the chamber or otherwise use a protective coating; use
- insulated wires outside. Ensure that the epoxy perfects the seal, or otherwise lay down a
- bead of water-proof silicone that can hold pressure.
- The screw fitting may require soft silicone sealant, or a gasket; its purpose is to hold
- pressure and allow periodic inspection of the electrodes. No leaks, no problems. Make
- sure you get a symmetric 1-5mm gap between the 2 stainless steel pipes. The referenced
- literature suggests that the closer to 1mm you get, the better. You WILL want to get your
- chamber level sensor verified BEFORE you epoxy the cap on.
- Make your solder connections at the wire/electrode junctions nice, smooth, and solid;
- then apply a water-proof coating, e.g. the epoxy you use for joining the pipes to the screw
- cap.
- This epoxy must be water-proof and be capable of holding metal to plastic under
- pressure.
- You WILL want to get your chamber level sensor verified BEFORE you epoxy the cap
- on.
- CONTROL CIRCUIT
- Figure 3
- ----------------------- Page 9-----------------------
- Figures 3 & 4 show a simple circuit to control and drive this mini-system. You are going
- to make a 'square-pulse' signal that 'plays' the electrodes like a tuning fork; which you
- can watch on an oscilloscope. The premise given by the literature is:
- ----------------------- Page 10-----------------------
- The faster you want do go down the road, the 'fatter' you make the pulses going into the
- reaction chamber. Duty cycle will vary with the throttle in the vicinity of 90%Mark
- 10%Space (Off/On).
- NOTE : Figures 4 and 5 have been revised, click to see the large version
- ----------------------- Page 11-----------------------
- ----------------------- Page 12-----------------------
- ----------------------- Page 13-----------------------
- There is nothing sacred about how the pulse waveform is generated; there are many ways
- to generate pulses, and the attached diagrams show a few. Figure 4 gives the NE555-
- circuit approach from the referenced patent. The output switching transistor must be
- rated for
- 1-5 amps @ I2VDC (in saturation).
- Go with a plan that works for you or your friendly neighbourhood technoid or mechanic,
- and go get all the circuit elements from your local electronics store, such as Radio-Shack
- or Circuits-R-Us, including the circuit board, IC sockets, and enclosure/box.
- DigiKey has better selection, service, and knowledge; plus they have no minimum order
- crap. Be sure to use a circuit board with a built-in ground plane, and to accommodate
- room for mounting 2 or 3 of the gauges. Mounting the reaction chamber in the engine
- compartment will require running a stub to your pressure gauge where you can watch it.
- You can easily make 30-gauge wire-wrap connections between the socket pins and
- through-hole discrete components having wire leads. Also make sure to get spec sheets on
- any IC you use. More details of the best circuits to use will be announced pending
- prototype testing. You WILL want to get your chamber level sensor verified BEFORE
- you epoxy the cap on.
- ----------------------- Page 14-----------------------
- ----------------------- Page 15-----------------------
- THROTTLE CONTROL
- If you have a throttle position sensor, you should be able to access the signal from the
- sensor itself OR from the computer connector. This signal is input to the circuit as the
- primary control (i.e. throttle level pulse width = vapour rate).
- ----------------------- Page 16-----------------------
- ----------------------- Page 17-----------------------
- If you don't have such a signal available, you will have to rig a rotary POT (variable
- resistor) to the gas linkage (i.e. coupled to something at the gas pedal or throttle cable
- running to the carb or Fl. If you make the attachment at the cart/Fl, be sure to use a POT
- that can handle the engine temp cycles. Don't use a cheezy-cheapy POT; get one rated for
- long life and mechanical wear; mount it securely to something sturdy and stationary that
- will not fall apart when you step on the gas.
- CONTROL RANGE
- The full throttle RANGE (idle-max) MUST control the vapour rate, i.e. pulse-width
- (duty). The resistor values at the throttle signal must allow the throttle signal voltage, say
- 1-4 Volt swing, to drive the VAPOR RATE. You will be using this voltage swing to
- generate a 10% ON 'square' pulse.
- The patent implies using a 'resonant' pulse in the 10-250 KHz frequency range; but it is
- not explicitly stated so. In this circuit, you will simply tune to whatever frequency makes
- the most efficient vapour conversion. You will have to get into the specs for each IC you
- use, to insure you connect the right pins to the right wires, to control the frequency and
- pulse width.
- You can use spare sockets to try out different discrete component values. Just keep the
- ones that are spec-compatible in the circuit, and get the job done.
- You crank up the throttle signal and put more electrical energy (fatter pulses) into the
- electrodes; verify you can get 10% duty on the scope (2 - 100 usec on the horizontal time-
- base). Your averaging DVM will display the 90%-I 0% DC voltage across the output
- transistor (Vce or Vds or Output to Ground). Set and connect DVM in the supply current
- and measure .5 - 5 amps, without blowing the DVM fuse. Now verify that you got
- everything you wanted.
- Verify your wiring connections using your DVM as a continuity detector. Check your
- wiring 1 at a time and yellow line your final schematic as you go. You can best use board-
- mount miniature POTs for anything you want to set-and-forget. The LEDs are there to
- give you a quick visual check of normal vs abnormal operation of your new creation. You
- WILL want to get your chamber level sensor verified BEFORE you epoxy the cap on (see
- Figures 2 & 4).
- Figure 2 also shows that fittings are required to the carb/FI I. There are ready-made kits
- (such as by Impco) available for making your pressure fittings to the carburetor or fuel-
- injector as the case may be. You will necessarily be sealing the built in vents and making a
- 1-way air-intake.
- The copper mesh comprises the inadvertent backfire' protection for the reaction
- chamber. Make sure that all vapor/duct junctions are air-tight and holding full pressure
- without leakage. Your new 'system' is considered successful and properly adjusted when
- you get the full power range at lower temp and minimum vapor flow without blowing the
- pressure safety valve.
- ----------------------- Page 18-----------------------
- CHT (or EGT)
- Monitor your engine temp with the CHT (cylinder head temp) or EGT (exhaust gas temp)
- instead of your original engine temp indicator (if any). Your existing gauge is TOO
- SLOW for this application and will not warn you against overheating until after you have
- burnt something.
- Make sure that your engine RUNS NO HOTTER than in the gasoline arrangement. VDO
- makes a CHT gauge with a platinum sensor that fits under your spark plug against the
- cylinder head (make sure it is REAL CLEAN before you reinstall your spark plug (as this
- is also an electrical ground).
- ENGINE/EXHAUST TREATMENT
- Get the valves replaced with stainless steel ones AND get the pistons/cylinders ceramic-
- treated ASAP when you have successfully converted and run your new creation. Do not
- delay as these items WILL RUST, either by sheer use or by neglect (i.e. letting it sit). You
- could make max use of your current exhaust system by using it with your new deal until it
- rusts through, then have your mechanic or welder friend to fit a stainless steel exhaust
- pipe (no catalytic converter is required). But it could be ea$ier to send your existing
- exhaust system out for the ceramic treatment, and then simply re-attach it to the exhaust
- ports.
- GENERAL
- 1. Do not discard or remove any of the old gasoline set up components, e.g. tank, carb/FI,
- catalytic converter, unless necessary. Better to always leave an easy way to revert back to
- something that at least runs, just in case. Some people are leaving their gasoline set up
- completely intact, and switching back and forth at will, just to have a backup plan.
- 2. Set your throttle circuit so that you get minimum vapour flow at IDLE, and maximum
- vapour flow at FULL POWER without blowing the pressure relief valve. In this way, you
- control how 'lean' your mixture is by the strength of the pulse (i.e. 'fatness' at the
- optimum pulse frequency).
- If you just don't get enough power (at any throttle setting), it means that you need to
- • (1) change the pulse frequency,
- • (2) change the gap between the electrodes,
- • (3) change the size (bigger) electrodes, OR
- • (4) make a higher output pulse voltage (last resort).
- Always use an output transistor, such as a MOSFET, that is rated for the voltage and
- current you need to get the job done. OK so you might have to play around with it some.
- Isn't that where all the Fun is anyhow?
- If you get ANY engine knock our loud combustions (not compensated by adjusting the
- timing), it means that you need to install an additional coil in the chamber, and drive the
- coil with an additional pulse signal (about 19 Hz on the .lsec time base) (see Figure 5).
- ----------------------- Page 19-----------------------
- Here, you will be slowing down the burn rate just enough so that the vapours burn
- throughout the power stroke of the piston. Be sure to include a board-mount POT to set
- the correct strength of this 2nd pulse signal into the coil. This is a stainless steel coil of
- about 1500 turns (thin wire) that you can arrange like a donut around the canter pipe
- (but NOT touching either electrode), directly over the circular 1-5mm gap. You want NO
- KNOCKING at any power/throttle setting; smooth power only, but also no excess
- hydrogen leftover from the combustion.
- 5. Build the canister(s) as tall as you can without compromising your ability to mount
- them conveniently near the dash panel, or in the engine compartment, as the case may be.
- This way, you can always make the electrodes bigger, if necessary without undue
- hardship. Remember that anything in the engine compartment should be mounted in a
- bullet-proof, vibration and temperature tolerant fashion.
- 6. If you have to drill a through-hole for wiring or plumbing through metal, make sure to
- also install a grommet for protection against chafing. Always watch your chamber
- pressure range from
- IDLE (15-25 psi) - FULL POWER (30-60 psi) - Set your safety-pressure relief-valve to 75
- psi and make sure it's rated for much higher.
- 7. Shut OFF the power switch and pull over if there is any MALFUNCTION of the
- system. Your engine will last longest when it still develops FULL POWER+ at some
- minimum temperature that we are sure you can find, by leaning back the Royal Vapour
- Flow and/or by making use of the water-vapour cooling technique (see Figure 7). Keep
- good mpg performance records, and periodic maintenance/inspection. Keep it clean; save
- some money; clean the air; heal the planet; happy motoring; tell a friend; enjoy your
- freedom and self-empowerment; haul ass.
- 8. There lacks documented material for perfecting this vapour system through a fuel
- injector; there may be some details you will discover on your own as working prototypes
- progress. For example, you may be restricted to inject the hydrogen/oxygen vapour
- WITHOUT ANY water vapour, as it may rust the injectors. If engine temp and CHT is a
- problem, then you will want to re-think your plan, e.g. ceramic-coating the injectors.
- There is always 'replacing the Fl system with a Carb'.
- 9. If you install the water-vapour system (for lower operating temp/stress), you will want
- to lean the mixture (vapour/air) for minimum vapour flow rate to achieve any given
- throttle position (idle - max). Make sure that you get a minimum flow for IDLE an a
- modestly sufficient flow for MAX, that does the cooling job without killing the
- combustion.
- 10. If you cannot find stainless steel pipe combinations that yield the 1-5mm gap, you can
- always regress back to alternating plates of +/- electrodes.
- 11. If you are concerned about the water freezing in your system, you can (a) add some
- 98% isopropyl alcohol and re-adjust the pulse frequency accordingly; or (b) install some
- electric heating coils.
- ----------------------- Page 20-----------------------
- 12. Do not let ANYONE ever compromise your dream, your freedom, your independence,
- your truth.
- REFERENCES
- 1. Stephen Chambers 'Apparatus for Producing Orthohydrogen and/or Parahydrogen'
- US Patent 6126794
- 2. Stanley Meyer 'Method for the Production of a Fuel Gas' US Patent 4936961
- 3. Creative Science & Research, 'Fuel From Water', fuelless.com
- 4. Carl Cella 'A Water-Fuelled Car' Nexus Magazine Oct-Nov 1996
- 5. Peter Lindemann's Free Energy site and his article from NEXUS
- 'Where in the World is All the Free Energy'
- 6. George Wiseman's Eagle Research
- 'The Gas-Saver and HyCO Series'
- 7. C. Michael Holler 'The Dromedary Newsletter' and 'SuperCarb Techniques'
- 8. Stephen Chambers 'Prototype Vapor Fuel System'
- DISCLAIMER: The author of this document assumes no liability for the use or misuse if
- this information; which is made available as public-domain information, for the purposes
- of education, ecology, health, well-being, freedom, liberty, and pursuit of happiness.
- COMMON LAW COPYRIGHT #285714: All rights to the use and duplication of these
- plans are hereby reserved for the People, in their efforts to heal and restore the
- environment. Dare to express your uniqueness and environmental ideals. This technology
- is an exercise in responsible self-determination.
- Thank you for your purchase, please leave me your positive feedback and after I will
- leave you the same feedback enjoy !
- Thank you Take care Best Regards U.M.S
- ----------------------- Page 21-----------------------
- ----------------------- Page 22-----------------------
- ----------------------- Page 23-----------------------
- Figure 3
- NOTE : Figures 4 and 5 have been revised, click to see the large version
- ----------------------- Page 24-----------------------
- ----------------------- Page 25-----------------------
- ----------------------- Page 26-----------------------
Advertisement
Add Comment
Please, Sign In to add comment