032915-Slic3r config

# generated by Slic3r 1.1.7 on Sun Mar 29 13:08:04 2015
avoid_crossing_perimeters = 0
bed_size = 184.15,200
bed_temperature = 0
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 2
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = M104 S0 ; turn off temperature\nG1 X0 Y180 F5000 ; push print out\nM84     ; disable motors\n
external_perimeter_speed = 75%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 3
fill_angle = 45
fill_density = 25%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_bed_temperature = 0
first_layer_extrusion_width = 0
first_layer_height = 0.4
first_layer_speed = 50%
first_layer_temperature = 0
g0 = 0
gap_fill_speed = 18
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 55
interface_shells = 0
layer_gcode =
layer_height = 0.35
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 20
min_skirt_length = 10
notes =
nozzle_diameter = 0.4
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 1
post_process =
print_center = 90,90
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 3.5
retract_length_toolchange = 0
retract_lift = 2
retract_restart_extra = 0.1
retract_restart_extra_toolchange = 0
retract_speed = 30
seam_position = aligned
skirt_distance = 4
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 15
small_perimeter_speed = 50%
solid_fill_pattern = rectilinear
solid_infill_below_area = 60
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60%
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ; home all axis\n\n
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 1
support_material_interface_spacing = 1
support_material_interface_speed = 50
support_material_pattern = rectilinear
support_material_spacing = 5
support_material_speed = 50
support_material_threshold = 0
temperature = 0
thin_walls = 1
threads = 4
toolchange_gcode =
top_infill_extrusion_width = 0
top_solid_infill_speed = 40%
top_solid_layers = 2
travel_speed = 120
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 3
wipe = 0
z_offset = 0