DDR Version 1.00 20141007
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT


U-Boot 2014.10-RK3288-01-g0933ad2 (Dec 11 2014 - 17:23:34)

CPU: rk3288
CPU's clock information:
    arm pll = 600000000HZ
    periph pll = 297000000HZ
    ddr pll = 200000000HZ
    codec pll = 384000000HZ
Board:	Rockchip platform Board
DRAM:  Found dram banks:1
Adding bank:0000000000000000(0000000080000000)
128 MiB
storage init OK!
Using default environment

GetParam
check parameter success
Unknow param: MACHINE_MODEL:rk30sdk!
Unknow param: MACHINE_ID:007!
Unknow param: MANUFACTURER:RK30SDK!
Unknow param: PWR_HLD: 0,0,A,0,1!
failed to prepare fdt from boot!
power key: bank-0 pin-5
can't find dts node for ricoh619
pmic:act8846
Can't find dts node for fuel guage cw201x
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2014-12-11#2.19
sn:****************
checkKey
vbus = 0
recovery key pressed.
no fuel gauge found
no fuel gauge found
read logo_on switch from dts [0]
no fuel gauge found
failed to load fdt from recovery!
kernel   @ 0x02000000 (0x002ecd3c)
ramdisk  @ 0x04bf0000 (0x00275b8f)
Secure Boot state: 0
bootrk: do_bootm_linux...
   Loading Device Tree to 04810000, end 0482b184 ... OK
Add bank:0000000000000000, 0000000080000000

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x500

Linux version 3.18.0-next-20141211+ (fun@build) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP Sat Dec 20 00:15:29 JST 2014

CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d

CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

Machine model: Firefly-RK3288

bootconsole [earlycon0] enabled

Memory policy: Data cache writealloc

PERCPU: Embedded 9 pages/cpu @ee7b4000 s7744 r8192 d20928 u36864

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 522768

Kernel command line: console=ttyS2,115200 earlyprintk init=/sbin/init root=/dev/mmcblk0p1 rootwait

PID hash table entries: 4096 (order: 2, 16384 bytes)

Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

Memory: 2073244K/2097152K available (4275K kernel code, 221K rwdata, 1368K rodata, 244K init, 290K bss, 23908K reserved, 0K cma-reserved, 1318912K highmem)

Virtual kernel memory layout:

    vector  : 0xffff0000 - 0xffff1000   (   4 kB)

    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)

    vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)

    lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)

    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)

    modules : 0xbf000000 - 0xbfe00000   (  14 MB)

      .text : 0xc0008000 - 0xc058af94   (5644 kB)

      .init : 0xc058b000 - 0xc05c8000   ( 244 kB)

      .data : 0xc05c8000 - 0xc05ff6d8   ( 222 kB)

       .bss : 0xc05ff6d8 - 0xc0647f24   ( 291 kB)

Hierarchical RCU implementation.

	Additional per-CPU info printed with stalls.

NR_IRQS:16 nr_irqs:16 16

L2C: failed to init: -19

Architected cp15 timer(s) running at 24.00MHz (phys).

sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns

Switching to timer-based delay loop, resolution 41ns

Console: colour dummy device 80x30

Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)

Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)

CPU: Testing write buffer coherency: ok

CPU0: thread -1, cpu 0, socket 5, mpidr 80000500

Setting up static identity map for 0x432498 - 0x4324f0

CPU1: thread -1, cpu 1, socket 5, mpidr 80000501

CPU2: thread -1, cpu 2, socket 5, mpidr 80000502

CPU3: thread -1, cpu 3, socket 5, mpidr 80000503

Brought up 4 CPUs

CPU: All CPU(s) started in SVC mode.

devtmpfs: initialized

VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0

pinctrl core: initialized pinctrl subsystem

NET: Registered protocol family 16

DMA: preallocated 256 KiB pool for atomic coherent allocations

cpuidle: using governor ladder

cpuidle: using governor menu

hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.

hw-breakpoint: maximum watchpoint size is 4 bytes.

reg-fixed-voltage sdmmc-regulator: Failed to find supply vin

reg-fixed-voltage sdmmc-regulator: Failed to register regulator: -517

platform sdmmc-regulator: Driver reg-fixed-voltage requests probe deferral

reg-fixed-voltage flash-regulator: Failed to find supply vin

reg-fixed-voltage flash-regulator: Failed to register regulator: -517

platform flash-regulator: Driver reg-fixed-voltage requests probe deferral

vcc_5v: supplied by vcc_sys

vcc_host_5v: supplied by vcc_5v

vcc_otg_5v: supplied by vcc_5v

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

pps_core: LinuxPPS API ver. 1 registered

pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>

PTP clock support registered

cfg80211: Calling CRDA to update world regulatory domain

Switched to clocksource arch_sys_counter

NET: Registered protocol family 2

TCP established hash table entries: 8192 (order: 3, 32768 bytes)

TCP bind hash table entries: 8192 (order: 4, 65536 bytes)

TCP: Hash tables configured (established 8192 bind 8192)

TCP: reno registered

UDP hash table entries: 512 (order: 2, 16384 bytes)

UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)

NET: Registered protocol family 1

futex hash table entries: 1024 (order: 4, 65536 bytes)

bounce: pool size: 64 pages

Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)

io scheduler noop registered

io scheduler deadline registered (default)

dma-pl330 ff250000.dma-controller: Loaded driver for PL330 DMAC-241330

dma-pl330 ff250000.dma-controller: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16

dma-pl330 ffb20000.dma-controller: Loaded driver for PL330 DMAC-241330

dma-pl330 ffb20000.dma-controller: 	DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10

Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled

dw-apb-uart ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 33, base_baud = 1500000) is a 16550A

dw-apb-uart ff190000.serial: ttyS1 at MMIO 0xff190000 (irq = 34, base_baud = 1500000) is a 16550A

console [ttyS2] disabled

dw-apb-uart ff690000.serial: ttyS2 at MMIO 0xff690000 (irq = 35, base_baud = 1500000) is a 16550A

console [ttyS2] enabled
console [ttyS2] enabled

bootconsole [earlycon0] disabled
bootconsole [earlycon0] disabled

dw-apb-uart ff1b0000.serial: ttyS3 at MMIO 0xff1b0000 (irq = 36, base_baud = 1500000) is a 16550A
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
dwc2 ff540000.usb: DWC OTG Controller
dwc2 ff540000.usb: new USB bus registered, assigned bus number 1
dwc2 ff540000.usb: irq 38, io mem 0x00000000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: DWC OTG Controller
usb usb1: Manufacturer: Linux 3.18.0-next-20141211+ dwc2_hsotg
usb usb1: SerialNumber: ff540000.usb
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb 1-1: new high-speed USB device number 2 using dwc2
usb 1-1: New USB device found, idVendor=1a40, idProduct=0101
usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1: Product: USB 2.0 Hub [MTT]
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
dwc2 ff580000.usb: DWC OTG Controller
dwc2 ff580000.usb: new USB bus registered, assigned bus number 2
dwc2 ff580000.usb: irq 39, io mem 0x00000000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: DWC OTG Controller
usb usb2: Manufacturer: Linux 3.18.0-next-20141211+ dwc2_hsotg
usb usb2: SerialNumber: ff580000.usb
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
rk3x-i2c ff140000.i2c: using default SCL frequency: 100000
rk3x-i2c ff140000.i2c: Initialized RK3xxx I2C bus at f00a6000
rk3x-i2c ff160000.i2c: using default SCL frequency: 100000
rk3x-i2c ff160000.i2c: Initialized RK3xxx I2C bus at f00a8000
rk3x-i2c ff170000.i2c: using default SCL frequency: 100000
rk3x-i2c ff170000.i2c: Initialized RK3xxx I2C bus at f00aa000
fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
vdd_cpu: supplied by vcc_sys
fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
vdd_gpu: supplied by vcc_sys
rtc-hym8563 0-0051: rtc core: registered hym8563 as rtc0
rk3x-i2c ff650000.i2c: Initialized RK3xxx I2C bus at f00ac000
rk3x-i2c ff660000.i2c: using default SCL frequency: 100000
rk3x-i2c ff660000.i2c: Initialized RK3xxx I2C bus at f00ae000
lirc_dev: IR Remote Control driver registered, major 247
IR NEC protocol handler initialized
IR RC5(x/sz) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
IR SANYO protocol handler initialized
IR Sharp protocol handler initialized
IR MCE Keyboard/mouse protocol handler initialized
IR LIRC bridge handler initialized
IR XMP protocol handler initialized
Registered IR keymap rc-empty
input: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc0/input0
rc0: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc0
input: MCE IR Keyboard/Mouse (gpio-rc-recv) as /devices/virtual/input/input1
rc rc0: lirc_dev: driver ir-lirc-codec (gpio-rc-recv) registered at minor = 0
rockchip-thermal ff280000.tsadc: Missing tshut mode property, using default (gpio)
rockchip-thermal ff280000.tsadc: Missing tshut-polarity property, using default (low)
thermal thermal_zone1: failed to read out thermal zone 1
thermal thermal_zone2: failed to read out thermal zone 2
softdog: Software Watchdog Timer: 0.08 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)
Driver 'mmcblk' needs updating - please use bus_type methods
Synopsys Designware Multimedia Card Interface Driver
dwmmc_rockchip ff0c0000.dwmmc: IDMAC supports 32-bit address mode.
dwmmc_rockchip ff0c0000.dwmmc: Using PIO mode.
dwmmc_rockchip ff0c0000.dwmmc: Version ID is 270a
dwmmc_rockchip ff0c0000.dwmmc: DW MMC controller at irq 24, 32 bit host data width, 256 deep fifo
platform ff0c0000.dwmmc: Driver dwmmc_rockchip requests probe deferral
dwmmc_rockchip ff0d0000.dwmmc: IDMAC supports 32-bit address mode.
dwmmc_rockchip ff0d0000.dwmmc: Using PIO mode.
dwmmc_rockchip ff0d0000.dwmmc: Version ID is 270a
dwmmc_rockchip ff0d0000.dwmmc: DW MMC controller at irq 25, 32 bit host data width, 256 deep fifo
dwmmc_rockchip ff0d0000.dwmmc: No vqmmc regulator found
mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
dwmmc_rockchip ff0d0000.dwmmc: 1 slots initialized
dwmmc_rockchip ff0f0000.dwmmc: IDMAC supports 32-bit address mode.
dwmmc_rockchip ff0f0000.dwmmc: Using PIO mode.
dwmmc_rockchip ff0f0000.dwmmc: Version ID is 270a
dwmmc_rockchip ff0f0000.dwmmc: DW MMC controller at irq 26, 32 bit host data width, 256 deep fifo
platform ff0f0000.dwmmc: Driver dwmmc_rockchip requests probe deferral
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usbcore: registered new interface driver r8188eu
usbcore: registered new interface driver rtl8723au
TCP: cubic registered
NET: Registered protocol family 17
Registering SWP/SWPB emulation handler
vcc_sd: supplied by vcc_io
vcc_flash: supplied by vcc_io
dwmmc_rockchip ff0c0000.dwmmc: IDMAC supports 32-bit address mode.
dwmmc_rockchip ff0c0000.dwmmc: Using PIO mode.
dwmmc_rockchip ff0c0000.dwmmc: Version ID is 270a
dwmmc_rockchip ff0c0000.dwmmc: DW MMC controller at irq 24, 32 bit host data width, 256 deep fifo
dwmmc_rockchip ff0c0000.dwmmc: No vqmmc regulator found
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
dwmmc_rockchip ff0c0000.dwmmc: 1 slots initialized
dwmmc_rockchip ff0f0000.dwmmc: IDMAC supports 32-bit address mode.
dwmmc_rockchip ff0f0000.dwmmc: Using PIO mode.
dwmmc_rockchip ff0f0000.dwmmc: Version ID is 270a
dwmmc_rockchip ff0f0000.dwmmc: DW MMC controller at irq 26, 32 bit host data width, 256 deep fifo
mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
dwmmc_rockchip ff0f0000.dwmmc: 1 slots initialized
input: gpio-keys as /devices/platform/gpio-keys/input/input2
rtc-hym8563 0-0051: setting system clock to 2011-01-01 12:26:59 UTC (1293884819)
vcc_sd: disabling
vcc18_lcd: disabling
vcca_33: disabling
vcca_18: disabling
vdd10_lcd: disabling
vdd_gpu: disabling
of_dma_request_slave_channel: dma-names property of node '/serial@ff690000' missing or empty
ttyS2 - failed to request DMA
Waiting for root device /dev/mmcblk0p1...
mmc2: BKOPS_EN bit is not set
mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc2: new high speed MMC card at address 0001
mmcblk0: mmc2:0001 AWMB3R 14.5 GiB
mmcblk0boot0: mmc2:0001 AWMB3R partition 1 4.00 MiB
mmcblk0boot1: mmc2:0001 AWMB3R partition 2 4.00 MiB
 mmcblk0: unknown partition table
VFS: Cannot open root device "mmcblk0p1" or unknown-block(179,1): error -6
Please append a correct "root=" boot option; here are the available partitions:
b300        15267840 mmcblk0  driver: mmcblk
b310            4096 mmcblk0boot1  (driver?)
b308            4096 mmcblk0boot0  (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,1)
CPU: 3 PID: 1 Comm: swapper/0 Not tainted 3.18.0-next-20141211+ #1
Hardware name: Rockchip Cortex-A9 (Device Tree)
Backtrace:
[<c0011d3c>] (dump_backtrace) from [<c0011f5c>] (show_stack+0x18/0x1c)
 r7:c05b8254 r6:ee314000 r5:c05ffbf0 r4:00000000
[<c0011f44>] (show_stack) from [<c042d9e4>] (dump_stack+0x78/0x94)
[<c042d96c>] (dump_stack) from [<c042c7e8>] (panic+0x90/0x1e8)
 r5:c05ffbf0 r4:ee314000
[<c042c75c>] (panic) from [<c058c288>] (mount_block_root+0x250/0x28c)
 r3:00000022 r2:ee11305c r1:ee05fed0 r0:c04faea8
 r7:c05b8254
[<c058c038>] (mount_block_root) from [<c058c404>] (mount_root+0x58/0x6c)
 r10:00000000 r9:c05ff700 r8:c05ff700 r7:c05c424c r6:c05b8269 r5:c04faf0c
 r4:0b300001
[<c058c3ac>] (mount_root) from [<c058c57c>] (prepare_namespace+0x164/0x1c4)
 r5:c05ff724 r4:c05b8254
[<c058c418>] (prepare_namespace) from [<c058be80>] (kernel_init_freeable+0x194/0x1e0)
 r6:c05b8230 r5:000000c0 r4:00000008
[<c058bcec>] (kernel_init_freeable) from [<c042bb28>] (kernel_init+0x14/0xec)
 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c042bb14 r4:c05ff700
[<c042bb14>] (kernel_init) from [<c000ea98>] (ret_from_fork+0x14/0x3c)
 r5:c042bb14 r4:00000000
CPU0: stopping
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.18.0-next-20141211+ #1
Hardware name: Rockchip Cortex-A9 (Device Tree)
Backtrace:
[<c0011d3c>] (dump_backtrace) from [<c0011f5c>] (show_stack+0x18/0x1c)
 r7:c05c9f6c r6:00000000 r5:00000000 r4:00000000
[<c0011f44>] (show_stack) from [<c042d9e4>] (dump_stack+0x78/0x94)
[<c042d96c>] (dump_stack) from [<c0013ed0>] (handle_IPI+0xd0/0x168)
 r5:00000000 r4:c05ff9d8
[<c0013e00>] (handle_IPI) from [<c000866c>] (gic_handle_irq+0x5c/0x64)
 r7:c05c9f6c r6:c05c9f38 r5:c05d1174 r4:f0002000
[<c0008610>] (gic_handle_irq) from [<c0012a00>] (__irq_svc+0x40/0x54)
Exception stack(0xc05c9f38 to 0xc05c9f80)
9f20:                                                       ffffffed 00000000
9f40: 00000000 c001d3a0 00000000 00000000 c05c5b48 c05d0400 00000000 ffffffed
9f60: 00000000 c05c9f8c c05c9f90 c05c9f80 c000f5f0 c000f5f4 60000113 ffffffff
 r7:c05c9f6c r6:ffffffff r5:60000113 r4:c000f5f4
[<c000f5c0>] (arch_cpu_idle) from [<c004c2e4>] (cpu_startup_entry+0xe0/0x23c)
[<c004c204>] (cpu_startup_entry) from [<c042bafc>] (rest_init+0x68/0x80)
 r7:c05d0400 r4:c05d0de0
[<c042ba94>] (rest_init) from [<c058bc80>] (start_kernel+0x330/0x39c)
[<c058b950>] (start_kernel) from [<00008074>] (0x8074)
 r9:410fc0d1 r8:0000406a r7:c05d3ff4 r6:c05b8424 r5:c05d0480 r4:c05ff994
CPU2: stopping
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 3.18.0-next-20141211+ #1
Hardware name: Rockchip Cortex-A9 (Device Tree)
Backtrace:
[<c0011d3c>] (dump_backtrace) from [<c0011f5c>] (show_stack+0x18/0x1c)
 r7:ee07ffa4 r6:00000000 r5:00000002 r4:00000000
[<c0011f44>] (show_stack) from [<c042d9e4>] (dump_stack+0x78/0x94)
[<c042d96c>] (dump_stack) from [<c0013ed0>] (handle_IPI+0xd0/0x168)
 r5:00000002 r4:c05ff9d8
[<c0013e00>] (handle_IPI) from [<c000866c>] (gic_handle_irq+0x5c/0x64)
 r7:ee07ffa4 r6:ee07ff70 r5:c05d1174 r4:f0002000
[<c0008610>] (gic_handle_irq) from [<c0012a00>] (__irq_svc+0x40/0x54)
Exception stack(0xee07ff70 to 0xee07ffb8)
ff60:                                     ffffffed 00000000 00000000 c001d3a0
ff80: 00000000 00000000 c05c5b48 c05ffa04 00000000 ffffffed 00000000 ee07ffc4
ffa0: ee07ffc8 ee07ffb8 c000f5f0 c000f5f4 60000113 ffffffff
 r7:ee07ffa4 r6:ffffffff r5:60000113 r4:c000f5f4
[<c000f5c0>] (arch_cpu_idle) from [<c004c2e4>] (cpu_startup_entry+0xe0/0x23c)
[<c004c204>] (cpu_startup_entry) from [<c0013bcc>] (secondary_start_kernel+0x124/0x148)
 r7:c05ffa04 r4:00000002
[<c0013aa8>] (secondary_start_kernel) from [<00008704>] (0x8704)
 r5:00000015 r4:2e06406a
CPU1: stopping
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.18.0-next-20141211+ #1
Hardware name: Rockchip Cortex-A9 (Device Tree)
Backtrace:
[<c0011d3c>] (dump_backtrace) from [<c0011f5c>] (show_stack+0x18/0x1c)
 r7:ee07dfa4 r6:00000000 r5:00000001 r4:00000000
[<c0011f44>] (show_stack) from [<c042d9e4>] (dump_stack+0x78/0x94)
[<c042d96c>] (dump_stack) from [<c0013ed0>] (handle_IPI+0xd0/0x168)
 r5:00000001 r4:c05ff9d8
[<c0013e00>] (handle_IPI) from [<c000866c>] (gic_handle_irq+0x5c/0x64)
 r7:ee07dfa4 r6:ee07df70 r5:c05d1174 r4:f0002000
[<c0008610>] (gic_handle_irq) from [<c0012a00>] (__irq_svc+0x40/0x54)
Exception stack(0xee07df70 to 0xee07dfb8)
df60:                                     ffffffed 00000000 00000000 c001d3a0
df80: 00000000 00000000 c05c5b48 c05ffa04 00000000 ffffffed 00000000 ee07dfc4
dfa0: ee07dfc8 ee07dfb8 c000f5f0 c000f5f4 60000113 ffffffff
 r7:ee07dfa4 r6:ffffffff r5:60000113 r4:c000f5f4
[<c000f5c0>] (arch_cpu_idle) from [<c004c2e4>] (cpu_startup_entry+0xe0/0x23c)
[<c004c204>] (cpu_startup_entry) from [<c0013bcc>] (secondary_start_kernel+0x124/0x148)
 r7:c05ffa04 r4:00000001
[<c0013aa8>] (secondary_start_kernel) from [<00008704>] (0x8704)
 r5:00000015 r4:2e06406a
---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,1)