API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Jun 4th, 2016
514
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
PowerShell 20.26 KB | None | 0 0
raw download clone embed print report
  1. root@turris:/# reboot
  2. procd: - shutdown -
  3. root@turris:/# [  687.511346] br-lan: port 2(eth1) entered disabled state
  4. [  687.516637] br-lan: port 1(eth0) entered disabled state
  5. [  687.522680] device eth0 left promiscuous mode
  6. [  687.527095] br-lan: port 1(eth0) entered disabled state
  7. [  687.533609] device eth1 left promiscuous mode
  8. [  687.538095] br-lan: port 2(eth1) entered disabled state
  9. procd: [  687.674354] Restarting system.
  10. - reboot -
  11.  
  12.  
  13. U-Boot 2015.04-04656-g6e465ba-dirty (Jun 26 2015 - 12:46:48)
  14.  
  15. CPU0:  P2020E, Version: 2.1, (0x80ea0021)
  16. Core:  e500, Version: 5.1, (0x80211051)
  17. Clock Configuration:
  18.        CPU0:1200 MHz, CPU1:1200 MHz,
  19.        CCB:600  MHz,
  20.        DDR:400  MHz (800 MT/s data rate) (Asynchronous), LBC:37.500 MHz
  21. L1:    D-cache 32 KiB enabled
  22.        I-cache 32 KiB enabled
  23. wdt status 00000005 reset
  24.        Watchdog enabled
  25. Board: TURRIS CPLD: V4.1 PCBA: V4.0
  26. Error, wrong i2c adapter 2 max 2 possible
  27. in: 56
  28. out: 0
  29. io_config: 255
  30. rom_loc: nor upper bank
  31. SD/MMC : 4-bit Mode
  32. eSPI : Enabled
  33. I2C:   Error, wrong i2c adapter 2 max 2 possible
  34. ready
  35. SPI:   ready
  36. DRAM:  Error, wrong i2c adapter 2 max 2 possible
  37. Detected UDIMM 9905428-181.A00LF
  38. 2 GiB (DDR3, 64-bit, CL=6, ECC off)
  39. Flash: 16 MiB
  40. L2:    512 KiB enabled
  41. NAND:  256 MiB
  42. MMC:   FSL_SDHC: 0
  43. *** Warning - bad CRC, using default environment
  44.  
  45. PCIe1: Root Complex of mini PCIe SLOT, no link, regs @ 0xffe0a000
  46. PCIe1: Bus 00 - 00
  47. PCIe2: Root Complex of PCIe SLOT, x1 gen1, regs @ 0xffe09000
  48.   02:00.0     - 168c:0030 - Network controller
  49. PCIe2: Bus 01 - 02
  50. PCIe3: Root Complex of PCIe SLOT, no link, regs @ 0xffe08000
  51. PCIe3: Bus 03 - 03
  52. Error, wrong i2c adapter 2 max 2 possible
  53. In:    serial
  54. Out:   serial
  55. Err:   serial
  56. Net:   Phy 5 not found
  57. PHY reset timed out
  58. eTSEC1
  59. Error: eTSEC1 address not set.
  60. , eTSEC2
  61. Error: eTSEC2 address not set.
  62. , eTSEC3 [PRIME]
  63. Error: eTSEC3 address not set.
  64.  
  65. Hit any key to stop autoboot:  0
  66. BOOT NAND
  67. wdt status 00000003
  68.  
  69. NAND read: device 0 offset 0x0, size 0x200000
  70.  2097152 bytes read: OK
  71.  
  72. Loading from nand0, offset 0x200000
  73.    Image Name:   Linux-3.10.18
  74.    Created:      2014-02-06  13:15:36 UTC
  75.    Image Type:   PowerPC Linux Kernel Image (gzip compressed)
  76.    Data Size:    1823906 Bytes = 1.7 MiB
  77.    Load Address: 00000000
  78.    Entry Point:  00000000
  79. WARNING: adjusting available memory to 30000000
  80. ## Booting kernel from Legacy Image at 02200000 ...
  81.    Image Name:   Linux-3.10.18
  82.    Created:      2014-02-06  13:15:36 UTC
  83.    Image Type:   PowerPC Linux Kernel Image (gzip compressed)
  84.    Data Size:    1823906 Bytes = 1.7 MiB
  85.    Load Address: 00000000
  86.    Entry Point:  00000000
  87.    Verifying Checksum ... OK
  88. ## Flattened Device Tree blob at 02000000
  89.    Booting using the fdt blob at 0x2000000
  90.    Uncompressing Kernel Image ... OK
  91.    Loading Device Tree to 03ffa000, end 03fffbfc ... OK
  92. WARNING: could not find compatible node fsl-usb2-dr
  93. [    0.000000] Using P2020 RDB machine description
  94. [    0.000000] Memory CAM mapping: 256/256 Mb, residual: 1536Mb
  95. [    0.000000] Linux version 3.10.18 (beast@ubuntu-openwrt) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38891) ) #1 SMP Thu Feb 6 14:15:32 CET 2014
  96. [    0.000000] CPU maps initialized for 1 thread per core
  97. [    0.000000] bootconsole [udbg0] enabled
  98. setup_arch: bootmem
  99. mpc85xx_rdb_setup_arch()
  100. [    0.000000] mpc85xx_rdb_setup_arch: Could not find Quicc Engine node
  101. [    0.000000] MPC85xx RDB board from Freescale Semiconductor
  102. arch: exit
  103. [    0.000000] Zone ranges:
  104. [    0.000000]   DMA      [mem 0x00000000-0x1fffffff]
  105. [    0.000000]   Normal   empty
  106. [    0.000000]   HighMem  [mem 0x20000000-0x7fffffff]
  107. [    0.000000] Movable zone start for each node
  108. [    0.000000] Early memory node ranges
  109. [    0.000000]   node   0: [mem 0x00000000-0x7fffffff]
  110. [    0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
  111. [    0.000000] PERCPU: Embedded 7 pages/cpu @c13d8000 s6816 r8192 d13664 u32768
  112. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 523264
  113. [    0.000000] Kernel command line: root=/dev/mtdblock8 rw rootfstype=jffs2 console=ttyS0,115200
  114. [    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
  115. [    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  116. [    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  117. [    0.000000] Sorting __ex_table...
  118. [    0.000000] Memory: 2010296k/2097152k available (3520k kernel code, 86856k reserved, 156k data, 209k bss, 180k init)
  119. [    0.000000] Kernel virtual memory layout:
  120. [    0.000000]   * 0xfffbf000..0xfffff000  : fixmap
  121. [    0.000000]   * 0xffc00000..0xffe00000  : highmem PTEs
  122. [    0.000000]   * 0xffbfd000..0xffc00000  : early ioremap
  123. [    0.000000]   * 0xe1000000..0xffbfd000  : vmalloc & ioremap
  124. [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  125. [    0.000000] Hierarchical RCU implementation.
  126. [    0.000000] NR_IRQS:512 nr_irqs:512 16
  127. [    0.000000] mpic: Setting up MPIC " OpenPIC  " version 1.2 at ffe40000, max 2 CPUs
  128. [    0.000000] mpic: ISU size: 256, shift: 8, mask: ff
  129. [    0.000000] mpic: Initializing for 256 sources
  130. [    0.000000] mpc85xx_rdb_pic_init: Could not find qe-ic node
  131. [    0.000000] clocksource: timebase mult[d555555] shift[24] registered
  132. [    0.006302] pid_max: default: 32768 minimum: 301
  133. [    0.010965] Mount-cache hash table entries: 512
  134. [    0.016957] mpic: requesting IPIs...
  135. [    0.021069] Brought up 2 CPUs
  136. [    0.024545] NET: Registered protocol family 16
  137.  
  138. [    0.036122] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->1
  139. [    0.043964] PCI host bridge /pcie@ffe09000 (primary) ranges:
  140. [    0.049611]  MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
  141. [    0.056825]   IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000
  142. [    0.063961] /pcie@ffe09000: PCICSRBAR @ 0xfff00000
  143. [    0.068998] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0
  144. [    0.076839] PCI host bridge /pcie@ffe0a000  ranges:
  145. [    0.081703]  MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000
  146. [    0.088917]   IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000
  147. [    0.096052] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
  148. [    0.110220] PCI: Probing PCI hardware
  149. [    0.113990] fsl-pci ffe09000.pcie: PCI host bridge to bus 0000:00
  150. [    0.120017] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
  151. [    0.126175] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xbfffffff]
  152. [    0.133043] pci_bus 0000:00: root bus resource [bus 00-ff]
  153. [    0.138555] pci 0000:00:00.0: ignoring class 0x0b2000 (doesn't match header type 01)
  154. [    0.154280] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
  155. [    0.159596] fsl-pci ffe0a000.pcie: PCI host bridge to bus 0001:02
  156. [    0.165614] pci_bus 0001:02: root bus resource [io  0x20000-0x2ffff] (bus address [0x0000-0xffff])
  157. [    0.174561] pci_bus 0001:02: root bus resource [mem 0x80000000-0x9fffffff]
  158. [    0.181429] pci_bus 0001:02: root bus resource [bus 02-ff]
  159. [    0.186932] pci 0001:02:00.0: ignoring class 0x0b2000 (doesn't match header type 01)
  160. [    0.194801] pci 0001:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  161. [    0.202840] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
  162. [    0.208081] pci 0000:00:00.0: BAR 9: can't assign mem pref (size 0x100000)
  163. [    0.214880] pci 0000:01:00.0: BAR 6: assigned [mem 0xa0020000-0xa002ffff pref]
  164. [    0.222090] pci 0000:00:00.0: PCI bridge to [bus 01]
  165. [    0.227044] pci 0000:00:00.0:   bridge window [io  0x0000-0xffff]
  166. [    0.233130] pci 0000:00:00.0:   bridge window [mem 0xa0000000-0xbfffffff]
  167. [    0.239911] pci 0001:02:00.0: PCI bridge to [bus 03]
  168. [    0.244865] pci 0001:02:00.0:   bridge window [io  0x20000-0x2ffff]
  169. [    0.251125] pci 0001:02:00.0:   bridge window [mem 0x80000000-0x9fffffff]
  170. [    0.257903] Some PCI device resources are unassigned, try booting with pci=realloc
  171. [    0.265471] pci 0000:00:00.0: enabling device (0106 -> 0107)
  172. [    0.271121] pci 0001:02:00.0: enabling device (0106 -> 0107)
  173. [    0.279753] bio: create slab <bio-0> at 0
  174. [    0.284842] Switching to clocksource timebase
  175. [    0.290270] NET: Registered protocol family 2
  176. [    0.294811] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
  177. [    0.301834] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
  178. [    0.308257] TCP: Hash tables configured (established 4096 bind 4096)
  179. [    0.314616] TCP: reno registered
  180. [    0.317781] UDP hash table entries: 256 (order: 1, 8192 bytes)
  181. [    0.323609] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  182. [    0.329987] NET: Registered protocol family 1
  183. [    0.335462] bounce pool size: 64 pages
  184. [    0.345007] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  185. [    0.350772] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  186. [    0.360924] msgmni has been set to 983
  187. [    0.364677] io scheduler noop registered
  188. [    0.368519] io scheduler deadline registered (default)
  189. [    0.413905] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
  190. [    0.422154] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A
  191. [    0.428918] console [ttyS0] enabled, bootconsole disabled
  192. [    0.428918] console [ttyS0] enabled, bootconsole disabled
  193. [    0.439987] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A
  194. [    0.447296] ffe04500.serial: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550
  195. [    0.454684] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550
  196. [    0.462872] ef000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
  197. [    0.472899] Amd/Fujitsu Extended Query Table at 0x0040
  198. [    0.478068]   Amd/Fujitsu Extended Query version 1.3.
  199. [    0.483125] number of CFI chips: 1
  200. [    0.486747] 6 ofpart partitions found on MTD device ef000000.nor
  201. [    0.492766] Creating 6 MTD partitions on "ef000000.nor":
  202. [    0.498090] 0x000000000000-0x000000020000 : "NOR (RO) DTB Image"
  203. [    0.504619] 0x000000020000-0x0000001c0000 : "NOR (RO) Linux Kernel Image"
  204. [    0.511895] 0x0000001c0000-0x000000340000 : "NOR (RO) JFFS2 Root File System"
  205. [    0.519540] 0x000000340000-0x000000e20000 : "NOR (RO) NAND FW backup"
  206. [    0.526454] 0x000000e40000-0x000000f00000 : "NOR (RW) Cert backup"
  207. [    0.533110] 0x000000f00000-0x000001000000 : "NOR (RO) U-Boot Image"
  208. [    0.544840] ONFI param page 0 valid
  209. [    0.548389] ONFI flash detected
  210. [    0.551533] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64
  211. [    0.563331] Bad block table found at page 131008, version 0x01
  212. [    0.569909] Bad block table found at page 130944, version 0x01
  213. [    0.576405] 3 ofpart partitions found on MTD device ff800000.flash
  214. [    0.582598] Creating 3 MTD partitions on "ff800000.flash":
  215. [    0.588088] 0x000000000000-0x000000200000 : "NAND (RW) DTB Image"
  216. [    0.594761] 0x000000200000-0x000000700000 : "NAND (RW) Linux Kernel Image"
  217. [    0.602144] 0x000000700000-0x000010000000 : "NAND (RW) JFFS2 Root File System"
  218. [    0.609962] eLBC NAND device at 0xff800000, bank 1
  219. [    0.615192] fsl_espi ffe07000.spi: master is unqueued, this is deprecated
  220. [    0.622025] fsl_espi ffe07000.spi: at 0xe103c000 (irq = 59)
  221. [    0.628013] ar8216: Module init.
  222. [    0.631718] libphy: Fixed MDIO Bus: probed
  223. [    0.636048] libphy: Freescale PowerQUICC MII Bus: probed
  224. [    0.641705] ar8216: probe addr 0.
  225. [    0.645119] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd033
  226. [    0.650196] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd034
  227. [    0.655249] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd036
  228. [    0.660403] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd033
  229. [    0.665455] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd034
  230. [    0.670507] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd036
  231. [    0.675661] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd033
  232. [    0.680712] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd034
  233. [    0.685764] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd036
  234. [    0.690919] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd033
  235. [    0.695970] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd034
  236. [    0.701022] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd036
  237. [    0.706073] ar8216: gonna list.
  238. [    0.709211] ar8216: after list.
  239. [    0.712349] ar8216: Identifying chip.
  240. [    0.737260] switch0: Atheros AR8327 rev. 2 switch registered on mdio@ffe24520
  241. [    0.744402] ar8216: FOUND!!!.
  242. [    1.958264] fsl-gianfar ffe24000.ethernet eth0: mac: 00:00:00:00:00:00
  243. [    1.964804] fsl-gianfar ffe24000.ethernet eth0: Running with NAPI enabled
  244. [    1.971598] fsl-gianfar ffe24000.ethernet eth0: RX BD ring size for Q[0]: 256
  245. [    1.978739] fsl-gianfar ffe24000.ethernet eth0: TX BD ring size for Q[0]: 256
  246. [    1.986321] fsl-gianfar ffe25000.ethernet eth1: mac: 00:00:00:00:00:00
  247. [    1.992862] fsl-gianfar ffe25000.ethernet eth1: Running with NAPI enabled
  248. [    1.999659] fsl-gianfar ffe25000.ethernet eth1: RX BD ring size for Q[0]: 256
  249. [    2.006801] fsl-gianfar ffe25000.ethernet eth1: TX BD ring size for Q[0]: 256
  250. [    2.014387] fsl-gianfar ffe26000.ethernet eth2: mac: 00:00:00:00:00:00
  251. [    2.020929] fsl-gianfar ffe26000.ethernet eth2: Running with NAPI enabled
  252. [    2.027760] fsl-gianfar ffe26000.ethernet eth2: RX BD ring size for Q[0]: 256
  253. [    2.034903] fsl-gianfar ffe26000.ethernet eth2: TX BD ring size for Q[0]: 256
  254. [    2.042159] ucc_geth_driver: QE UCC Gigabit Ethernet Controller
  255. [    2.048462] i2c /dev entries driver
  256. [    2.052126] mpc-i2c ffe03000.i2c: timeout 1000000 us
  257. [    2.059751] rtc-mcp7940 0-006f: rtc core: registered mcp7940 as rtc0
  258. [    2.066183] mpc-i2c ffe03100.i2c: timeout 1000000 us
  259. [    2.071487] booke_wdt: powerpc book-e watchdog driver loaded
  260. [    2.077532] TCP: cubic registered
  261. [    2.080845] NET: Registered protocol family 17
  262. [    2.085373] Bridge firewalling registered
  263. [    2.089390] 8021q: 802.1Q VLAN Support v1.8
  264. [    2.095043] rtc-mcp7940 0-006f: setting system clock to 2016-06-04 07:41:57 UTC (1465026117)
  265. [    3.919021] jffs2: notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
  266. [    3.937941] VFS: Mounted root (jffs2 filesystem) on device 31:8.
  267. [    3.944152] Freeing unused kernel memory: 180K (c0343000 - c0370000)
  268. procd: Console is alive
  269. procd: - watchdog -
  270. procd: - preinit -
  271. ifconfig: SIOCSIFFLAGS: Cannot assign requested address
  272. sendto(): Network is unreachable
  273. Press the [f] key and hit [enter] to enter failsafe mode
  274. [    5.467908] usbcore: registered new interface driver usbfs
  275. [    5.473501] usbcore: registered new interface driver hub
  276. [    5.478948] usbcore: registered new device driver usb
  277. [    5.486251] Button Hotplug driver version 0.4.1
  278. [    5.496324] SCSI subsystem initialized
  279. [    5.502717] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  280. [    5.509326] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
  281. [    5.515969] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
  282. [    5.523268] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000
  283. [    5.537150] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
  284. [    5.543059] hub 1-0:1.0: USB hub found
  285. [    5.546828] hub 1-0:1.0: 1 port detected
  286. [    5.551334] ehci-platform: EHCI generic platform driver
  287. [    5.561735] sdhci: Secure Digital Host Controller Interface driver
  288. [    5.567929] sdhci: Copyright(c) Pierre Ossman
  289. [    5.572681] sdhci-pltfm: SDHCI platform and OF driver helper
  290. [    5.609152] mmc0: SDHCI controller on ffe2e000.sdhc [ffe2e000.sdhc] using DMA
  291. [    5.620146] usbcore: registered new interface driver usb-storage
  292. [    5.861161] usb 1-1: new high-speed USB device number 2 using fsl-ehci
  293. [    5.998127] hub 1-1:1.0: USB hub found
  294. [    6.002016] hub 1-1:1.0: 2 ports detected
  295. mount_root: mounting /dev/root
  296. ifconfig: SIOCSIFFLAGS: Cannot assign requested address
  297. procd: - early -
  298. procd: - watchdog -
  299. procd: - ubus -
  300. procd: - init -
  301. Please press Enter to activate this console.
  302. [    8.779879] NET: Registered protocol family 10
  303. [    8.789012] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
  304. [    8.798133] ip6_tables: (C) 2000-2006 Netfilter Core Team
  305. [    8.813927] Loading modules backported from Linux version master-2013-11-05-0-gafa3093
  306. [    8.821902] Backport generated by backports.git backports-20130802-0-gdb67a3f
  307. [    8.833740] ip_tables: (C) 2000-2006 Netfilter Core Team
  308. [    8.886846] usbcore: registered new interface driver ums-alauda
  309. [    8.897575] usbcore: registered new interface driver ums-cypress
  310. [    8.904405] usbcore: registered new interface driver ums-datafab
  311. [    8.911189] usbcore: registered new interface driver ums-freecom
  312. [    8.918044] usbcore: registered new interface driver ums-isd200
  313. [    8.924811] usbcore: registered new interface driver ums-jumpshot
  314. [    8.931671] usbcore: registered new interface driver ums-karma
  315. [    8.938552] usbcore: registered new interface driver ums-sddr09
  316. [    8.945440] usbcore: registered new interface driver ums-sddr55
  317. [    8.952298] usbcore: registered new interface driver ums-usbat
  318. [    8.963530] xt_time: kernel timezone is -0000
  319. [    8.976588] cfg80211: Calling CRDA to update world regulatory domain
  320. [    8.983342] cfg80211: World regulatory domain updated:
  321. [    8.988530] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  322. [    8.996725] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  323. [    9.004476] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  324. [    9.012229] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  325. [    9.019979] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
  326. [    9.027730] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
  327. [    9.035480] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
  328. [    9.092511] PPP generic driver version 2.4.2
  329. [    9.097667] NET: Registered protocol family 24
  330. [    9.274511] cfg80211: Calling CRDA for country: US
  331. [    9.279700] cfg80211: Regulatory domain changed to country: US
  332. [    9.285570] cfg80211:  DFS Master region FCC
  333. [    9.289673] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  334. [    9.298034] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
  335. [    9.305814] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 1700 mBm)
  336. [    9.313567] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
  337. [    9.321320] cfg80211:   (5490000 KHz - 5600000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
  338. [    9.329072] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2400 mBm)
  339. [    9.336823] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 3000 mBm)
  340. [    9.344575] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
  341. [    9.352516] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xf3540000, irq=24
  342. [   18.434053] ar8216: Module config init.
  343. [   18.438260] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  344. [   18.445881] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
  345. [   18.453656] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
  346. [   19.013815] ar8216: Module config init.
  347. [   19.017911] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  348. [   19.024106] device eth0 entered promiscuous mode
  349. [   19.031640] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  350. [   19.041323] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
  351. [   19.047552] device eth1 entered promiscuous mode
  352. [   19.166374] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
  353. [   20.017152] ar8216: config aneg.
  354. [   21.023425] libphy: mdio@ffe24520:00 - Link is Up - 1000/Full
  355. [   21.029821] br-lan: port 1(eth0) entered forwarding state
  356. [   21.035254] br-lan: port 1(eth0) entered forwarding state
  357. [   21.040684] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  358. [   21.048459] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  359. [   21.055132] libphy: fixed-0:06 - Link is Up - 1000/Full
  360. [   21.060382] br-lan: port 2(eth1) entered forwarding state
  361. [   21.065802] br-lan: port 2(eth1) entered forwarding state
  362. [   21.071313] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
  363. [   22.165476] libphy: mdio@ffe24520:07 - Link is Up - 100/Full
  364. [   22.171764] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
  365. [   23.037150] br-lan: port 1(eth0) entered forwarding state
  366. [   23.069142] br-lan: port 2(eth1) entered forwarding state
  367. procd: - init complete -
  368. procd: Instance log::instance1 s in a crash loop 6 crashes, 0 seconds since last crash
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!