Data hosted with ♥ by Pastebin.com - Download Raw - See Original
  1.  
  2. PRELOADER.3.2.0.REL_R2787.w11
  3. DD: efuse2: 00006070 => 55e7 => 0x01c4; 00000060 => 0xbcc8... done
  4. DD: efuse3: 00000505 => 0xbcc4... done
  5. DD: efuse4: 00008999 => 0xbcdc... done
  6. DD: efuse5: 0000aaaa => 0xbce0... done
  7. DD: efuse6: di: a1; sds_num: 0; gphy_num: 0
  8. DD: efuse gphy: done
  9. DD: efuse sds: done
  10. DD: efuse lxb: break
  11. II: Disabling OCP/LX timeout monitors... done
  12. Get prestate = 1 in the init stage...
  13. II: NOR SPI-F... Generic 3B NOR SPI-F [00ef4018] selected... done
  14. II: OCP 100MHz(400/P4/C1), MEM 325MHz, LX 200MHz, SPIF 50MHz(1000/(5*4))
  15.  
  16. DRAM AUTO CALIBRATION
  17. AutoK: ZQ Calibration Passed
  18. AutoK: MR0: 0x00100b62
  19. AutoK: MR1: 0x00110040
  20. AutoK: MR2: 0x00120000
  21. AutoK: MR3: 0x00130000
  22. bit:00, max_w_s(00), max_w_len(21), max_r_s(00), max_r_len(31): (0xb8001510) = 0x1e0f00
  23. bit:01, max_w_s(00), max_w_len(21), max_r_s(02), max_r_len(29): (0xb8001514) = 0x1e1102
  24. bit:02, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb8001518) = 0x1e1102
  25. bit:03, max_w_s(00), max_w_len(21), max_r_s(02), max_r_len(29): (0xb800151c) = 0x1e1102
  26. bit:04, max_w_s(00), max_w_len(21), max_r_s(02), max_r_len(29): (0xb8001520) = 0x1e1102
  27. bit:05, max_w_s(00), max_w_len(21), max_r_s(02), max_r_len(29): (0xb8001524) = 0x1e1102
  28. bit:06, max_w_s(00), max_w_len(21), max_r_s(00), max_r_len(31): (0xb8001528) = 0x1e0f00
  29. bit:07, max_w_s(00), max_w_len(21), max_r_s(00), max_r_len(31): (0xb800152c) = 0x1e0f00
  30. bit:08, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb8001530) = 0x1e1102
  31. bit:09, max_w_s(00), max_w_len(21), max_r_s(00), max_r_len(31): (0xb8001534) = 0x1e0f00
  32. bit:10, max_w_s(00), max_w_len(19), max_r_s(00), max_r_len(31): (0xb8001538) = 0x1e0f00
  33. bit:11, max_w_s(00), max_w_len(21), max_r_s(02), max_r_len(29): (0xb800153c) = 0x1e1102
  34. bit:12, max_w_s(00), max_w_len(21), max_r_s(02), max_r_len(29): (0xb8001540) = 0x1e1102
  35. bit:13, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb8001544) = 0x1e1102
  36. bit:14, max_w_s(00), max_w_len(21), max_r_s(02), max_r_len(29): (0xb8001548) = 0x1e1102
  37. bit:15, max_w_s(00), max_w_len(21), max_r_s(00), max_r_len(31): (0xb800154c) = 0x1e0f00
  38. bit:16, max_w_s(00), max_w_len(17), max_r_s(02), max_r_len(29): (0xb8001550) = 0x1e1102
  39. bit:17, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb8001554) = 0x1e1102
  40. bit:18, max_w_s(00), max_w_len(17), max_r_s(04), max_r_len(27): (0xb8001558) = 0x1e1304
  41. bit:19, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb800155c) = 0x1e1102
  42. bit:20, max_w_s(00), max_w_len(19), max_r_s(04), max_r_len(27): (0xb8001560) = 0x1e1304
  43. bit:21, max_w_s(00), max_w_len(17), max_r_s(02), max_r_len(29): (0xb8001564) = 0x1e1102
  44. bit:22, max_w_s(00), max_w_len(19), max_r_s(00), max_r_len(31): (0xb8001568) = 0x1e0f00
  45. bit:23, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb800156c) = 0x1e1102
  46. bit:24, max_w_s(00), max_w_len(17), max_r_s(02), max_r_len(29): (0xb8001570) = 0x1e1102
  47. bit:25, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb8001574) = 0x1e1102
  48. bit:26, max_w_s(00), max_w_len(17), max_r_s(00), max_r_len(31): (0xb8001578) = 0x1e0f00
  49. bit:27, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb800157c) = 0x1e1102
  50. bit:28, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb8001580) = 0x1e1102
  51. bit:29, max_w_s(00), max_w_len(17), max_r_s(02), max_r_len(29): (0xb8001584) = 0x1e1102
  52. bit:30, max_w_s(00), max_w_len(19), max_r_s(04), max_r_len(27): (0xb8001588) = 0x1e1304
  53. bit:31, max_w_s(00), max_w_len(17), max_r_s(00), max_r_len(31): (0xb800158c) = 0x1e0f00
  54. AutoK: dram auto calibrtaion is done
  55.  
  56. II: MEM_PROBE_OK
  57. II: MEM_XLAT_OK
  58. II: MEM_TO_REG_OK
  59. II: MEM_CNTLR_ZQ_STRICT_OK
  60. II: MEM_CAL_OK
  61. II: cntlr zq result: 0018e975
  62. II: dcr result: 11210000
  63. II: Decompressing U-Boot (0x80f00000 <- 0x9fc1a200)... (212 KB <- 80 KB) OK
  64. II: Starting U-boot...
  65.  
  66. CIG Version: 3.04.09
  67.  
  68. U-Boot 2011.12.NA-svn94986 (Jan 15 2016 - 17:00:30)
  69.  
  70. Board: RTL9601B CPU:100MHz LX:200MHz DDR2:325MHz..
  71. SPI-F: 1x16 MB (plr_flash_info @ 9f002d20)
  72. [debug] start to init flash_info (1)
  73. [debug] <0> unit size=0x10000, unit count=256
  74. *** Warning - bad CRC, using default environment
  75.  
  76. *** !!! Check Result: Chk_CRC: 0x0, Chk_Empty: 0x0
  77. Net: LUNA GMAC
  78. Warning: eth device name has a space!
  79.  
  80. **************************************
  81. * *
  82. * KEY -- Enter console terminal *
  83. * *
  84. **************************************
  85. waiting for your select .....
  86. do_jffs2_fsload offset 0x80400000 loadaddr=0xbd088000..
  87. get loadbit 0,bootbit 0
  88. Get current Image = ImageA..
  89.  
  90. --- jffs2_part_info: partition number 2 for device sflash0 (sflash.0)
  91.  
  92. Loading 'uImage' from CRAMFS Partition 'imagea' to 0x80400000.
  93.  
  94. Root Filesystem crc check successfully!
  95.  
  96.  
  97. PRODUCT: sfu
  98. SS : noss
  99. DSP : nodsp
  100. WIFI: nowifi
  101. XDSL: nodsl
  102. Software version: 3FE45655AOCK31
  103. ## Booting kernel from Legacy Image at 80400000 ...
  104. Image Name: Linux Kernel Image
  105. Created: 2015-12-11 6:28:09 UTC
  106. Image Type: MIPS Linux Kernel Image (gzip compressed)
  107. Data Size: 1440099 Bytes = 1.4 MB
  108. Load Address: 80000000
  109. Entry Point: 80000000
  110. Verifying Checksum ... OK
  111. Uncompressing Kernel Image ... OK
  112.  
  113. Starting kernel ...
  114.  
  115. Linux version 2.6.30.9-cig-sfu-1 (taojipeng@sw1-dev) (gcc version 4.4.6 (Realtek RSDK-1.5.6p2) ) #1 Fri Dec 11 11:48:11 CST 2015
  116. CPU revision is: 0000dc02
  117. Determined physical RAM map:
  118. memory: 03800000 @ 00000000 (usable)
  119. User-defined physical RAM map:
  120. memory: 01f00000 @ 00000000 (usable)
  121. Zone PFN ranges:
  122. Normal 0x00000000 -> 0x00001f00
  123. Movable zone start PFN for each node
  124. early_node_map[1] active PFN ranges
  125. 0: 0x00000000 -> 0x00001f00
  126. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 7874
  127. Kernel command line: console=ttyS0,115200 mem=31M root=/dev/mtdblock2 mtdparts=sflash:512K@0x0(Boot),0x180000@0x80000(Config),7M@0x200000(ImageA),7M@0x900000(ImageB) rootfstype=cramfs hasEeprom=0 5srst=0
  128. root_dev_setup line 179 root: /dev/mtdblock2
  129. icache: 64kB/32B, dcache: 32kB/32B, scache: 0kB/0B
  130. NR_IRQS:128
  131. PID hash table entries: 128 (order: 7, 512 bytes)
  132. console [ttyS0] enabled
  133. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  134. Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  135. Memory: 28056k/31744k available (2448k kernel code, 3688k reserved, 653k data, 108k init, 0k highmem)
  136. Calibrating delay loop... 97.79 BogoMIPS (lpj=48896)
  137. Mount-cache hash table entries: 512
  138. IMEM section size = 0x3244
  139. net_namespace: 788 bytes
  140. NET: Registered protocol family 16
  141. bio: create slab <bio-0> at 0
  142. Sangoma WANPIPE Router v1.1 (c) 1995-2000 Sangoma Technologies Inc.
  143. NET: Registered protocol family 2
  144. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  145. TCP established hash table entries: 1024 (order: 1, 8192 bytes)
  146. TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  147. TCP: Hash tables configured (established 1024 bind 1024)
  148. TCP reno registered
  149. NET: Registered protocol family 1
  150. Realtek GPIO Driver for Flash Reload Default
  151. netlog: listening on port 4660
  152. NTFS driver 2.1.29 [Flags: R/W].
  153. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
  154. msgmni has been set to 54
  155. alg: No test for stdrng (krng)
  156. io scheduler noop registered
  157. io scheduler deadline registered
  158. io scheduler cfq registered (default)
  159. Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  160. serial8250: ttyS0 at MMIO 0x0 (irq = 49) is a 16550A
  161. loop: module loaded
  162. PPP generic driver version 2.4.2
  163. NET: Registered protocol family 24
  164. ===============================================================================
  165. init_luna_nor_spi_map: flash map at 0xbd000000
  166. luna spi probe...
  167. luna SPI FLASH G2 driver version 1.00-II: NOR SPI-F... Generic 3B NOR SPI-F detected... done
  168. master->name sflash
  169. cmd: cmdlinepart
  170. 4 cmdlinepart partitions found on MTD device sflash
  171. add luna nor spi partition
  172. MTD partitions obtained from kernel command line
  173. Creating 4 MTD partitions on "sflash":
  174. 0x000000000000-0x000000080000 : "Boot"
  175. 0x000000080000-0x000000200000 : "Config"
  176. 0x000000200000-0x000000900000 : "ImageA"
  177. 0x000000900000-0x000001000000 : "ImageB"
  178. ===============================================================================
  179. u32 classifier
  180. nf_conntrack version 0.5.0 (496 buckets, 1984 max)
  181. ip_tables: (C) 2000-2006 Netfilter Core Team
  182. TCP cubic registered
  183. Realtek SD2-FastPath v1.00beta_2.4.26-uc0
  184. /proc/FastPath created
  185. Realtek MCast FastPath
  186. /proc/mc_FastPath created
  187. NET: Registered protocol family 10
  188. lo: Disabled Privacy Extensions
  189. IPv6 over IPv4 tunneling driver
  190. sit0: Disabled Privacy Extensions
  191. ip6tnl0: Disabled Privacy Extensions
  192. NET: Registered protocol family 17
  193. Bridge firewalling registered
  194. Ebtables v2.0 registered
  195. VFS: Mounted root (cramfs filesystem) readonly on device 31:2.
  196. Freeing unused kernel memory: 108k freed
  197.  
  198. # num is 10,nothing need to do
  199. ONT>Starting Application: 0x00002000, /bin/TimerMgr................Done.
  200. Starting Application: 0x00001000, /bin/LogMgr................Done.
  201. app 0x00007000 stop invalid timer[0]
  202. ### Invalid Decimal_Factor, use default 0xdb
  203. ### Invalid Settle_Time, use default 0x68
  204. ### Invalid P1_Mask, use default 0x5a
  205. ### Invalid P0_Mask, use default 0x8
  206. Tx has been calibrated!!
  207. Starting Application: 0x00007000, /bin/MiscMgr................Done.
  208. Check base image file CRC ... cal_crc (706307a4) ori_crc (706307a4) Success.
  209. Mount Backup[/dev/mtdblock3] as cramfs...Success.
  210. major ID[0xa9] minor ID[0x1]
  211. cp: can't stat '/mnt/rwdir2/sys.log': No such file or directory
  212. mv: can't create '/mnt/rwdir2/sys.log': Read-only file system
  213. cp: can't stat '/mnt/rwdir2/sys.log': No such file or directory
  214. mv: can't create '/mnt/rwdir2/sys.log': Read-only file system
  215. Starting Application: 0x00003000, /bin/MecMgr................Done.
  216. Starting Application: 0x00004000, /bin/PonMgr................Done.
  217. ------>NET open default xml failedStarting Application: 0x00009000, /bin/NetMgr................Done.
  218. Starting Application: 0x00005000, /bin/EthMgr................Done.
  219. Starting Application: 0x0000c000, /bin/WebMgr................Done.
  220. Laser TX OFF
  221. Laser TX ON
  222. Preparing stress ...
  223.  
  224. INFO: ALL APPs are ready.
  225. ONT>ls
  226. ONT>
  227. ONT>cd /
  228. ONT>