Sd card 1 s905w

GXL:BL1:9ac50e:bb16dc;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:800;NAND:0;READ:0;0.0;CHK                                                                          :0;
TE: 24512

BL2 Built : 11:04:41, Jan 26 2018.
gxl g034b32c - xingyu.chen@droid12-sz

set vcck to 1120 mv
set vddee to 1000 mv
Board ID = 1
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0 16bit @ 720MHz

bist_test rank: 0 2c 01 57 35 0f 5c 2f 05 59 36 0e 5f 35 35 35 35 35 35 34 34 34                                                                           34 34 34 637
Rank0: 2048MB-2T-11
AddrBus test pass!
NAND init
Load fip header from NAND, src: 0x0000c000, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from NAND, src: 0x00010000, des: 0x01100000, size: 0x0000d600
Load bl31 from NAND, src: 0x00020000, des: 0x05100000, size: 0x0002c600
Load bl33 from NAND, src: 0x00050000, des: 0x01000000, size: 0x00067200
NOTICE:  BL3-1: v1.0(release):35dd647
NOTICE:  BL3-1: Built : 15:20:30, Feb  7 2018
[BL31]: GXL CPU setup!
NOTICE:  BL31: BL33 decompress pass
mpu_config_enable:ok
[Image: gxl_v1.1.3308-b30529c-dirty 2018-05-28 19:44:39]
OPS=0xc4
21 0d c4 00 b6 b1 a3 f8 49 9d f4 a8 7d 17 fc 3e
[0.352819 Inits done]
secure task start!
high task start!
low task start!
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01 (Sep 07 2018 - 16:46:33)

DRAM:  2 GiB
Relocation Offset is: 76eb0000
===============y20180907k=====================
register usb cfg[0][1] = 0000000077f59ae0
[CANVAS]canvas init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
NAND device id: 2c 84 64 54 a9 0 0 0
detect NAND device: B revision L95B NAND 16GiB MT29F128G08CBECB
param data[32~43]: 53, 50, 45, 43,54, 45
nand Manufacturer: specteck

bus_c=6,bus_t=7,sys=4.0ns,T_REA=16,T_RHOH=15
new oob mode
show_phydev_list
0: nfboot
detect new nand here and new_type:50
NAND CKECK:arg nbbt: valid=1, blk=9, page=0
NAND CKECK:arg fbbt: valid=1, blk=3, page=0
outside dtb: 0000000000000000
using dtb on nand
amlnf_dtb_init_partitions: probe.
NAND CKECK:arg ndtb: valid=1, blk=7, page=17
dtb magic 5f4c4d41
      Amlogic multi-dtb tool
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 2 dtbs.
        aml_dt soc: gxl platform: p212 variant: 2g
        dtb 0 soc: gxl   plat: p212   vari: 1g
        dtb 1 soc: gxl   plat: p212   vari: 2g
      Find match dtb: 1
start dts,buffer=0000000073ed6300,dt_addr=0000000073ee1300
      Amlogic multi-dtb tool
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 2 dtbs.
        aml_dt soc: gxl platform: p212 variant: 2g
        dtb 0 soc: gxl   plat: p212   vari: 1g
        dtb 1 soc: gxl   plat: p212   vari: 2g
      Find match dtb: 1
parts: 10
00:      logo   0000000002000000 1
01:  recovery   0000000002000000 1
02:       rsv   0000000000800000 1
03:       tee   0000000000800000 1
04:     crypt   0000000002000000 1
05:      misc   0000000002000000 1
06:      boot   0000000002000000 1
07:    system   0000000080000000 1
08:     cache   0000000020000000 2
09:      data   ffffffffffffffff 4
cache !!!
NAND CKECK:arg ncnf: valid=1, blk=2, page=0
aml_key_init probe.
NAND CKECK:arg nkey: valid=1, blk=4, page=17
boot_device_flag 1
NAND CKECK:arg nenv: valid=1, blk=6, page=15
NAND CKECK:arg phyp: valid=1, blk=5, page=1
amlnand_phydev_init,1429,phydev->offset=0,phydev->size=1000000
amlnand_phydev_init,1429,phydev->offset=19000000,phydev->size=2a000000
amlnand_phydev_init,1429,phydev->offset=43000000,phydev->size=9e000000
amlnand_phydev_init,1429,phydev->offset=e1000000,phydev->size=31f000000
nfboot    : 0x000000000000-0x000001000000 :partn=0:single_chip single_plane
nfcache   : 0x000019000000-0x00002a000000 :partn=1:single_chip multi_plane
nfcode    : 0x000043000000-0x00009e000000 :partn=8:single_chip multi_plane
nfdata    : 0x0000e1000000-0x00031f000000 :partn=1:single_chip multi_plane
amlnf_logic_init() start
(nfcache), size:2a000000
nftl version 1.01.002
Nov 18 2016, fix logic partition calculation
size_in_blk 42; total_block 41;
get the phy_dev_size=20000000H tmp_off_size=100000H phy_dev_block=21Hnftl start:                                                                          size_in_blk=41,free_block_num=8-blks(37), total_blocks(33)
this part not enough free block 37 , 33!!
 create_part_list fail!
aml_nftl_initialize: fail
(nfcode), size:9e000000
nftl version 1.01.002
Nov 18 2016, fix logic partition calculation
get the phy_dev_size=8b000000H tmp_off_size=458000H phy_dev_block=8cHnftl start:                                                                          size_in_blk=158,free_block_num=18-blks(153), total_blocks(140)
amlnf_logic_init() done
MMC:   aml_priv->desc_buf = 0x0000000073f05c10
aml_priv->desc_buf = 0x0000000073f07f30
SDIO Port B: 0, SDIO Port C: 1
uboot env amlnf_env_read : ####
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
[store]To run cmd[amlnf dtb_read 0x1000000 0x40000]
cmd dtb_read:
amlnf_dtb_read: ####
262144 bytes dtd_read : OK
      Amlogic multi-dtb tool
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 2 dtbs.
        aml_dt soc: gxl platform: p212 variant: 2g
        dtb 0 soc: gxl   plat: p212   vari: 1g
        dtb 1 soc: gxl   plat: p212   vari: 2g
      Find match dtb: 1
vpu: clk_level in dts: 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpu: vpu_clk_gate_init_off
vpp: vpp_init
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970000
HPLL: 0xc000027b
config HPLL done
j = 4  vid_clk_div = 1
hdmitx: set enc for VIC: 16
HDMITX-DWC addr=0x10004006 rd_data=0x40
Error: HDMITX-DWC exp_data=0xff mask=0x9f
rx version is 1.4 or below  div=10
hdmtix: set audio
hdmitx phy setting done
Net:   dwmac.c9410000amlkey_init() enter!
[EFUSE_MSG]keynum is 8
[BL31]: tee size: 0

Start read misc partition datas!
info->attemp_times = 0
info->active_slot = 0
info->slot_info[0].bootable = 1
info->slot_info[0].online = 1
info->slot_info[1].bootable = 0
info->slot_info[1].online = 0
info->attemp_times = 0
attemp_times = 0
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f851000
[CANVAS]addr=0x7f851000 width=3840, height=2160
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 8
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
detect sadckey ....
update by key...
InUsbBurn
noSof
card in
init_part() 278: PART_TYPE_DOS
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL16G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 14.8 GiB
mmc clock: 40000000
Bus Width: 4-bit
[MSG]Reload bmps env.
Err imgread(L587):Logo header err.
[MSG]ini sz 0x25dB
[fat]Filesize is 0x25dB[0M]
[fat]0x:leftSz 25d < BPS 2000, gotSz 25d

=========sdc_burn_paras=====>>>
[common]
erase_bootloader = 0
erase_flash      = 2
reboot           = 0x0
key_overwrite    = 0x0

[burn_ex]
package          = atvXperience_tx3_mini_v1.3.img
media            =

[burn_parts]
burn_num         = 0

<<<<=====sdc_burn_paras======

[fat]Filesize is 0x3d3b1dd4B[979M]
[fat]0x:leftSz c40 < BPS 2000, gotSz 6c40
[MSG]image version [0x00000002]
[MSG]cfg10=0xADFC318C
[fat]Seek 0xbab00 from 0x6c40
[MSG]itemSizeNotAligned 0x1500
[MSG]align 4 mmc read...        [fat]0x:leftSz 300 < BPS 2000, gotSz 15800
[MSG]Down(mem) part(dtb) sz(0x15800) fmt(normal)
[MSG]Burn Start...
[MSG]load dt.img to 0x0000000001000000, sz=0x15800
[MSG]Burn complete
[MSG]echo video prepare for upgrade
hpd_state=1
[OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[CANVAS]addr=0x3d800000 width=3840, height=2160
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970000
HPLL: 0xc000027b
config HPLL done
j = 4  vid_clk_div = 1
hdmitx: set enc for VIC: 16
rx version is 1.4 or below  div=10
hdmtix: set audio
hdmitx phy setting done
[MSG]dw,dh[1920, 1080]
[MSG]w,h[4,14]
[MSG]Exit before re-init
command:        store  exit
amlnf_exit : ok
dtb magic 5f4c4d41
      Amlogic multi-dtb tool
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 2 dtbs.
        aml_dt soc: gxl platform: p212 variant: 2g
        dtb 0 soc: gxl   plat: p281   vari: 1g
        dtb 1 soc: gxl   plat: p281   vari: 2g
      Not match any dtb.
start dts,buffer=0000000001000000,dt_addr=0000000001000000
check_valid_dts: FDT_ERR_BADMAGIC
get_partition_from_dts: -9
ERR(../drivers/usb/gadget/v2_burning/v2_common/optimus_download.c)L761:Failed at                                                                           get_partition_from_dts
ERR(../drivers/usb/gadget/v2_burning/v2_sdc_burn/optimus_sdc_burn.c)L663:Fail to                                                                           init stoarge for sdc burn
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL16G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 14.8 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading aml_autoscript
** Unable to read file aml_autoscript **
reading recovery.img
** Unable to read file recovery.img **
(Re)start USB...
USB0:   USB3.0 XHCI init start
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
"Synchronous Abort" handler, esr 0x96000004
ELR:     77f00bd4
LR:      77f02f48
x0 : 73666d61723d6570 x1 : 0000000073efae80
x2 : 0000000000010000 x3 : 0000000000000800
x4 : 0000000001080000 x5 : 0000000000000000
x6 : 0000000077f35678 x7 : 0000000000000044
x8 : 0000000000000001 x9 : 0000000000000000
x10: 000000000000000f x11: 0000000077f379b0
x12: 0000000000000000 x13: 0000000000000000
x14: 0000000000000000 x15: 0000000000000000
x16: 0000000000000000 x17: 0000000000000000
x18: 0000000073e9fe28 x19: 0000000073efae00
x20: 0000000000000000 x21: 0000000073efae80
x22: 0000000001080000 x23: 0000000000000000
x24: 0000000000000800 x25: 0000000077f0073c
x26: 0000000077f50000 x27: 0000000073efb970
x28: 0000000000000000 x29: 0000000073e9e6c0

Resetting CPU ...