daily pastebin goal
56%
SHARE
TWEET

Untitled

a guest Dec 21st, 2012 26 Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1.   1.647168] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
  2. [    1.647170] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
  3. [    1.647187] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf2a04c00
  4. [    1.648577] ehci_hcd 0000:00:1d.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN
  5. [    1.654015] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
  6. [    1.655440] usb usb2: default language 0x0409
  7. [    1.655448] usb usb2: udev 1, busnum 2, minor = 128
  8. [    1.655451] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
  9. [    1.656896] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  10. [    1.658380] usb usb2: Product: EHCI Host Controller
  11. [    1.659864] usb usb2: Manufacturer: Linux 3.7.1-gentoo ehci_hcd
  12. [    1.661352] usb usb2: SerialNumber: 0000:00:1d.7
  13. [    1.662908] usb usb2: usb_probe_device
  14. [    1.662911] usb usb2: configuration #1 chosen from 1 choice
  15. [    1.662918] usb usb2: adding 2-0:1.0 (config #1, interface 0)
  16. [    1.662973] hub 2-0:1.0: usb_probe_interface
  17. [    1.662976] hub 2-0:1.0: usb_probe_interface - got id
  18. [    1.662979] hub 2-0:1.0: USB hub found
  19. [    1.664487] hub 2-0:1.0: 6 ports detected
  20. [    1.665936] hub 2-0:1.0: standalone hub
  21. [    1.665938] hub 2-0:1.0: no power switching (usb 1.0)
  22. [    1.665941] hub 2-0:1.0: individual port over-current protection
  23. [    1.665943] hub 2-0:1.0: power on to power good time: 20ms
  24. [    1.665947] hub 2-0:1.0: local power source is good
  25. [    1.666069] hub 2-0:1.0: trying to enable port power on non-switchable hub
  26. [    1.666171] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  27. [    1.667660] ohci_hcd: block sizes: ed 64 td 64
  28. [    1.667717] uhci_hcd: USB Universal Host Controller Interface driver
  29. [    1.669207] uhci_hcd 0000:00:1a.0: setting latency timer to 64
  30. [    1.669211] uhci_hcd 0000:00:1a.0: UHCI Host Controller
  31. [    1.670738] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
  32. [    1.672216] uhci_hcd 0000:00:1a.0: detected 2 ports
  33. [    1.673684] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000
  34. [    1.673687] uhci_hcd 0000:00:1a.0: Performing full reset
  35. [    1.673703] uhci_hcd 0000:00:1a.0: supports USB remote wakeup
  36. [    1.673719] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001820
  37. [    1.675202] usb usb3: default language 0x0409
  38. [    1.675210] usb usb3: udev 1, busnum 3, minor = 256
  39. [    1.675213] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
  40. [    1.676654] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  41. [    1.678087] usb usb3: Product: UHCI Host Controller
  42. [    1.679564] usb usb3: Manufacturer: Linux 3.7.1-gentoo uhci_hcd
  43. [    1.681019] usb usb3: SerialNumber: 0000:00:1a.0
  44. [    1.682568] usb usb3: usb_probe_device
  45. [    1.682572] usb usb3: configuration #1 chosen from 1 choice
  46. [    1.682578] usb usb3: adding 3-0:1.0 (config #1, interface 0)
  47. [    1.682633] hub 3-0:1.0: usb_probe_interface
  48. [    1.682636] hub 3-0:1.0: usb_probe_interface - got id
  49. [    1.682639] hub 3-0:1.0: USB hub found
  50. [    1.684042] hub 3-0:1.0: 2 ports detected
  51. [    1.685414] hub 3-0:1.0: standalone hub
  52. [    1.685416] hub 3-0:1.0: no power switching (usb 1.0)
  53. [    1.685418] hub 3-0:1.0: individual port over-current protection
  54. [    1.685421] hub 3-0:1.0: power on to power good time: 2ms
  55. [    1.685425] hub 3-0:1.0: local power source is good
  56. [    1.685444] hub 3-0:1.0: trying to enable port power on non-switchable hub
  57. [    1.685490] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.0
  58. [    1.685512] uhci_hcd 0000:00:1a.1: setting latency timer to 64
  59. [    1.685516] uhci_hcd 0000:00:1a.1: UHCI Host Controller
  60. [    1.686944] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
  61. [    1.688300] uhci_hcd 0000:00:1a.1: detected 2 ports
  62. [    1.689634] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000
  63. [    1.689636] uhci_hcd 0000:00:1a.1: Performing full reset
  64. [    1.689652] uhci_hcd 0000:00:1a.1: supports USB remote wakeup
  65. [    1.689668] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001840
  66. [    1.691011] usb usb4: default language 0x0409
  67. [    1.691019] usb usb4: udev 1, busnum 4, minor = 384
  68. [    1.691022] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
  69. [    1.692334] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  70. [    1.693641] usb usb4: Product: UHCI Host Controller
  71. [    1.694982] usb usb4: Manufacturer: Linux 3.7.1-gentoo uhci_hcd
  72. [    1.696292] usb usb4: SerialNumber: 0000:00:1a.1
  73. [    1.697691] usb usb4: usb_probe_device
  74. [    1.697694] usb usb4: configuration #1 chosen from 1 choice
  75. [    1.697702] usb usb4: adding 4-0:1.0 (config #1, interface 0)
  76. [    1.697761] hub 4-0:1.0: usb_probe_interface
  77. [    1.697764] hub 4-0:1.0: usb_probe_interface - got id
  78. [    1.697767] hub 4-0:1.0: USB hub found
  79. [    1.699077] hub 4-0:1.0: 2 ports detected
  80. [    1.700348] hub 4-0:1.0: standalone hub
  81. [    1.700351] hub 4-0:1.0: no power switching (usb 1.0)
  82. [    1.700353] hub 4-0:1.0: individual port over-current protection
  83. [    1.700355] hub 4-0:1.0: power on to power good time: 2ms
  84. [    1.700359] hub 4-0:1.0: local power source is good
  85. [    1.700378] hub 4-0:1.0: trying to enable port power on non-switchable hub
  86. [    1.700426] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.1
  87. [    1.700448] uhci_hcd 0000:00:1a.2: setting latency timer to 64
  88. [    1.700452] uhci_hcd 0000:00:1a.2: UHCI Host Controller
  89. [    1.701847] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
  90. [    1.703156] uhci_hcd 0000:00:1a.2: detected 2 ports
  91. [    1.704458] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000
  92. [    1.704461] uhci_hcd 0000:00:1a.2: Performing full reset
  93. [    1.704476] uhci_hcd 0000:00:1a.2: supports USB remote wakeup
  94. [    1.704487] uhci_hcd 0000:00:1a.2: irq 19, io base 0x00001860
  95. [    1.705794] usb usb5: default language 0x0409
  96. [    1.705801] usb usb5: udev 1, busnum 5, minor = 512
  97. [    1.705804] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
  98. [    1.707116] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  99. [    1.708427] usb usb5: Product: UHCI Host Controller
  100. [    1.709746] usb usb5: Manufacturer: Linux 3.7.1-gentoo uhci_hcd
  101. [    1.711077] usb usb5: SerialNumber: 0000:00:1a.2
  102. [    1.712471] usb usb5: usb_probe_device
  103. [    1.712474] usb usb5: configuration #1 chosen from 1 choice
  104. [    1.712481] usb usb5: adding 5-0:1.0 (config #1, interface 0)
  105. [    1.712534] hub 5-0:1.0: usb_probe_interface
  106. [    1.712537] hub 5-0:1.0: usb_probe_interface - got id
  107. [    1.712540] hub 5-0:1.0: USB hub found
  108. [    1.713886] hub 5-0:1.0: 2 ports detected
  109. [    1.715201] hub 5-0:1.0: standalone hub
  110. [    1.715203] hub 5-0:1.0: no power switching (usb 1.0)
  111. [    1.715206] hub 5-0:1.0: individual port over-current protection
  112. [    1.715208] hub 5-0:1.0: power on to power good time: 2ms
  113. [    1.715212] hub 5-0:1.0: local power source is good
  114. [    1.715231] hub 5-0:1.0: trying to enable port power on non-switchable hub
  115. [    1.715278] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.2
  116. [    1.715301] uhci_hcd 0000:00:1d.0: setting latency timer to 64
  117. [    1.715305] uhci_hcd 0000:00:1d.0: UHCI Host Controller
  118. [    1.716684] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
  119. [    1.718022] uhci_hcd 0000:00:1d.0: detected 2 ports
  120. [    1.719330] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
  121. [    1.719332] uhci_hcd 0000:00:1d.0: Performing full reset
  122. [    1.719348] uhci_hcd 0000:00:1d.0: supports USB remote wakeup
  123. [    1.719354] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001880
  124. [    1.720669] usb usb6: default language 0x0409
  125. [    1.720676] usb usb6: udev 1, busnum 6, minor = 640
  126. [    1.720679] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
  127. [    1.721984] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  128. [    1.723318] usb usb6: Product: UHCI Host Controller
  129. [    1.724657] usb usb6: Manufacturer: Linux 3.7.1-gentoo uhci_hcd
  130. [    1.725977] usb usb6: SerialNumber: 0000:00:1d.0
  131. [    1.727381] usb usb6: usb_probe_device
  132. [    1.727384] usb usb6: configuration #1 chosen from 1 choice
  133. [    1.727391] usb usb6: adding 6-0:1.0 (config #1, interface 0)
  134. [    1.727444] hub 6-0:1.0: usb_probe_interface
  135. [    1.727446] hub 6-0:1.0: usb_probe_interface - got id
  136. [    1.727449] hub 6-0:1.0: USB hub found
  137. [    1.728756] hub 6-0:1.0: 2 ports detected
  138. [    1.730061] hub 6-0:1.0: standalone hub
  139. [    1.730063] hub 6-0:1.0: no power switching (usb 1.0)
  140. [    1.730065] hub 6-0:1.0: individual port over-current protection
  141. [    1.730068] hub 6-0:1.0: power on to power good time: 2ms
  142. [    1.730072] hub 6-0:1.0: local power source is good
  143. [    1.730092] hub 6-0:1.0: trying to enable port power on non-switchable hub
  144. [    1.730140] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0
  145. [    1.730159] uhci_hcd 0000:00:1d.1: setting latency timer to 64
  146. [    1.730162] uhci_hcd 0000:00:1d.1: UHCI Host Controller
  147. [    1.731547] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
  148. [    1.732871] uhci_hcd 0000:00:1d.1: detected 2 ports
  149. [    1.734178] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
  150. [    1.734181] uhci_hcd 0000:00:1d.1: Performing full reset
  151. [    1.734196] uhci_hcd 0000:00:1d.1: supports USB remote wakeup
  152. [    1.734202] uhci_hcd 0000:00:1d.1: irq 19, io base 0x000018a0
  153. [    1.735534] usb usb7: default language 0x0409
  154. [    1.735541] usb usb7: udev 1, busnum 7, minor = 768
  155. [    1.735544] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
  156. [    1.736885] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  157. [    1.738023] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001803 0  ACK POWER sig=j CSC CONNECT
  158. [    1.738026] hub 1-0:1.0: port 1: status 0501 change 0001
  159. [    1.738035] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 001803 0  ACK POWER sig=j CSC CONNECT
  160. [    1.738038] hub 1-0:1.0: port 2: status 0501 change 0001
  161. [    1.738207] usb usb7: Product: UHCI Host Controller
  162. [    1.739502] usb usb7: Manufacturer: Linux 3.7.1-gentoo uhci_hcd
  163. [    1.740823] usb usb7: SerialNumber: 0000:00:1d.1
  164. [    1.742248] usb usb7: usb_probe_device
  165. [    1.742251] usb usb7: configuration #1 chosen from 1 choice
  166. [    1.742258] usb usb7: adding 7-0:1.0 (config #1, interface 0)
  167. [    1.742314] hub 7-0:1.0: usb_probe_interface
  168. [    1.742316] hub 7-0:1.0: usb_probe_interface - got id
  169. [    1.742319] hub 7-0:1.0: USB hub found
  170. [    1.743625] hub 7-0:1.0: 2 ports detected
  171. [    1.744912] hub 7-0:1.0: standalone hub
  172. [    1.744914] hub 7-0:1.0: no power switching (usb 1.0)
  173. [    1.744916] hub 7-0:1.0: individual port over-current protection
  174. [    1.744919] hub 7-0:1.0: power on to power good time: 2ms
  175. [    1.744923] hub 7-0:1.0: local power source is good
  176. [    1.744966] hub 7-0:1.0: trying to enable port power on non-switchable hub
  177. [    1.745025] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1
  178. [    1.745044] uhci_hcd 0000:00:1d.2: setting latency timer to 64
  179. [    1.745047] uhci_hcd 0000:00:1d.2: UHCI Host Controller
  180. [    1.746418] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
  181. [    1.747743] uhci_hcd 0000:00:1d.2: detected 2 ports
  182. [    1.749053] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
  183. [    1.749055] uhci_hcd 0000:00:1d.2: Performing full reset
  184. [    1.749071] uhci_hcd 0000:00:1d.2: supports USB remote wakeup
  185. [    1.749087] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018c0
  186. [    1.750426] usb usb8: default language 0x0409
  187. [    1.750433] usb usb8: udev 1, busnum 8, minor = 896
  188. [    1.750436] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
  189. [    1.751737] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  190. [    1.753055] usb usb8: Product: UHCI Host Controller
  191. [    1.754351] usb usb8: Manufacturer: Linux 3.7.1-gentoo uhci_hcd
  192. [    1.755671] usb usb8: SerialNumber: 0000:00:1d.2
  193. [    1.757100] usb usb8: usb_probe_device
  194. [    1.757103] usb usb8: configuration #1 chosen from 1 choice
  195. [    1.757110] usb usb8: adding 8-0:1.0 (config #1, interface 0)
  196. [    1.757163] hub 8-0:1.0: usb_probe_interface
  197. [    1.757166] hub 8-0:1.0: usb_probe_interface - got id
  198. [    1.757169] hub 8-0:1.0: USB hub found
  199. [    1.758474] hub 8-0:1.0: 2 ports detected
  200. [    1.759787] hub 8-0:1.0: standalone hub
  201. [    1.759790] hub 8-0:1.0: no power switching (usb 1.0)
  202. [    1.759792] hub 8-0:1.0: individual port over-current protection
  203. [    1.759794] hub 8-0:1.0: power on to power good time: 2ms
  204. [    1.759799] hub 8-0:1.0: local power source is good
  205. [    1.759840] hub 8-0:1.0: trying to enable port power on non-switchable hub
  206. [    1.759891] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2
  207. [    1.759997] usbcore: registered new interface driver usblp
  208. [    1.761290] Initializing USB Mass Storage driver...
  209. [    1.762679] usbcore: registered new interface driver usb-storage
  210. [    1.764031] USB Mass Storage support registered.
  211. [    1.765477] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
  212. [    1.766925] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
  213. [    1.770959] i8042: Detected active multiplexing controller, rev 1.1
  214. [    1.776377] serio: i8042 KBD port at 0x60,0x64 irq 1
  215. [    1.777741] serio: i8042 AUX0 port at 0x60,0x64 irq 12
  216. [    1.779105] serio: i8042 AUX1 port at 0x60,0x64 irq 12
  217. [    1.780447] serio: i8042 AUX2 port at 0x60,0x64 irq 12
  218. [    1.781788] serio: i8042 AUX3 port at 0x60,0x64 irq 12
  219. [    1.783177] mousedev: PS/2 mouse device common for all mice
  220. [    1.784899] rtc_cmos 00:06: RTC can wake from S4
  221. [    1.786373] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
  222. [    1.787701] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
  223. [    1.789035] uhci_hcd 0000:00:1a.0: port 1 portsc 008a,00
  224. [    1.789050] uhci_hcd 0000:00:1a.0: port 2 portsc 0082,00
  225. [    1.789098] i2c /dev entries driver
  226. [    1.790520] i2c-dev: adapter [i915 gmbus ssc] registered as minor 0
  227. [    1.790573] i2c-dev: adapter [i915 gmbus vga] registered as minor 1
  228. [    1.790626] i2c-dev: adapter [i915 gmbus panel] registered as minor 2
  229. [    1.790679] i2c-dev: adapter [i915 gmbus dpc] registered as minor 3
  230. [    1.790736] i2c-dev: adapter [i915 gmbus dpb] registered as minor 4
  231. [    1.790789] i2c-dev: adapter [i915 gmbus dpd] registered as minor 5
  232. [    1.790844] i2c-dev: adapter [DPDDC-B] registered as minor 6
  233. [    1.790898] i2c-dev: adapter [DPDDC-D] registered as minor 7
  234. [    1.790921] ACPI Warning: 0x00001c00-0x00001c1f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20120913/utaddress-251)
  235. [    1.792362] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
  236. [    1.794254] device-mapper: ioctl: 4.23.0-ioctl (2012-07-25) initialised: dm-devel@redhat.com
  237. [    1.795794] cpuidle: using governor ladder
  238. [    1.797306] cpuidle: using governor menu
  239. [    1.798919] sdhci: Secure Digital Host Controller Interface driver
  240. [    1.800368] sdhci: Copyright(c) Pierre Ossman
  241. [    1.800403] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
  242. [    1.801798] sdhci-pci 0000:02:00.0: SDHCI controller found [197b:2382] (rev 0)
  243. [    1.803258] sdhci-pci 0000:02:00.0: found 1 slot(s)
  244. [    1.803314] sdhci [sdhci_add_host()]: mmc0: Auto-CMD23 unavailable
  245. [    1.803327] sdhci: =========== REGISTER DUMP (mmc0)===========
  246. [    1.803332] sdhci: Sys addr: 0x00000000 | Version:  0x0000b001
  247. [    1.803338] sdhci: Blk size: 0x00000000 | Blk cnt:  0x00000000
  248. [    1.803345] sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
  249. [    1.803351] sdhci: Present:  0x00080000 | Host ctl: 0x00000000
  250. [    1.803357] sdhci: Power:    0x00000000 | Blk gap:  0x00000000
  251. [    1.803362] sdhci: Wake-up:  0x00000000 | Clock:    0x00000000
  252. [    1.803367] sdhci: Timeout:  0x00000000 | Int stat: 0x00000000
  253. [    1.803373] sdhci: Int enab: 0x00ff0003 | Sig enab: 0x00ff0003
  254. [    1.803378] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
  255. [    1.803383] sdhci: Caps:     0x014032b2 | Caps_1:   0x00000000
  256. [    1.803388] sdhci: Cmd:      0x00000000 | Max curr: 0x00000000
  257. [    1.803397] sdhci: Host ctl2: 0x00000000
  258. [    1.803398] sdhci: ===========================================
  259. [    1.803486] Registered led device: mmc0::
  260. [    1.803654] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 0 timing 0
  261. [    1.814074] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  262. [    1.815056] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
  263. [    1.824758] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
  264. [    1.826267] mmc0: SDHCI controller on PCI [0000:02:00.0] using DMA
  265. [    1.826280] mmc0: mmc_rescan_try_freq: trying to init card at 400000 Hz
  266. [    1.826283] mmc0: starting CMD52 arg 00000c00 flags 00000195
  267. [    1.826302] mmc0: req done (CMD52): -123: 00000000 00000000 00000000 00000000
  268. [    1.826343] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  269. [    1.826348] mmc0: gated MCI clock
  270. [    1.826351] mmc0: starting CMD52 arg 80000c08 flags 00000195
  271. [    1.826353] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  272. [    1.826360] mmc0: ungated MCI clock
  273. [    1.826374] mmc0: req done (CMD52): -123: 00000000 00000000 00000000 00000000
  274. [    1.826402] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  275. [    1.826407] mmc0: gated MCI clock
  276. [    1.826410] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  277. [    1.826417] mmc0: ungated MCI clock
  278. [    1.826419] mmc0: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  279. [    1.826450] mmc0: clock 0Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  280. [    1.826455] mmc0: gated MCI clock
  281. [    1.828018] mmc0: starting CMD0 arg 00000000 flags 000000c0
  282. [    1.828020] mmc0: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  283. [    1.828027] mmc0: ungated MCI clock
  284. [    1.828042] mmc0: req done (CMD0): -123: 00000000 00000000 00000000 00000000
  285. [    1.828070] mmc0: clock 0Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  286. [    1.828075] mmc0: gated MCI clock
  287. [    1.829303] sdhci-pci 0000:02:00.2: SDHCI controller found [197b:2381] (rev 0)
  288. [    1.830040] mmc0: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  289. [    1.830049] mmc0: ungated MCI clock
  290. [    1.830051] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  291. [    1.830083] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  292. [    1.830088] mmc0: gated MCI clock
  293. [    1.830795] sdhci-pci 0000:02:00.2: found 1 slot(s)
  294. [    1.830810] sdhci-pci 0000:02:00.2: Refusing to bind to secondary interface.
  295. [    1.832332] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000
  296. [    1.832338] mmc0: starting CMD8 arg 000001aa flags 000002f5
  297. [    1.832341] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  298. [    1.832349] mmc0: ungated MCI clock
  299. [    1.832363] mmc0: req done (CMD8): -123: 00000000 00000000 00000000 00000000
  300. [    1.832364] wbsd: Winbond W83L51xD SD/MMC card interface driver
  301. [    1.832365] wbsd: Copyright(c) Pierre Ossman
  302. [    1.832639] VUB300 Driver rom wait states = 1C irqpoll timeout = 0400
  303. [    1.832639] usbcore: registered new interface driver vub300
  304. [    1.832680] usbcore: registered new interface driver ushc
  305. [    1.832681] sdhci-pltfm: SDHCI platform and OF driver helper
  306. [    1.832682] EFI Variables Facility v0.08 2004-May-17
  307. [    1.833602] usbcore: registered new interface driver usbhid
  308. [    1.833603] usbhid: USB HID core driver
  309. [    1.833802] Netfilter messages via NETLINK v0.30.
  310. [    1.833816] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
  311. [    1.834041] ctnetlink v0.93: registering with nfnetlink.
  312. [    1.834189] ip_tables: (C) 2000-2006 Netfilter Core Team
  313. [    1.834220] TCP: cubic registered
  314. [    1.834221] Initializing XFRM netlink socket
  315. [    1.834485] NET: Registered protocol family 10
  316. [    1.834755] ip6_tables: (C) 2000-2006 Netfilter Core Team
  317. [    1.834790] sit: IPv6 over IPv4 tunneling driver
  318. [    1.835053] NET: Registered protocol family 17
  319. [    1.835079] lib80211: common routines for IEEE802.11 drivers
  320. [    1.835081] lib80211_crypt: registered algorithm 'NULL'
  321. [    1.835082] lib80211_crypt: registered algorithm 'WEP'
  322. [    1.835083] lib80211_crypt: registered algorithm 'CCMP'
  323. [    1.835084] lib80211_crypt: registered algorithm 'TKIP'
  324. [    1.835096] Key type dns_resolver registered
  325. [    1.835201] kworker/u:7 (1083) used greatest stack depth: 6972 bytes left
  326. [    1.835410] Using IPI No-Shortcut mode
  327. [    1.835556] PM: Hibernation image not present or could not be loaded.
  328. [    1.835570] registered taskstats version 1
  329. [    1.836294]   Magic number: 8:531:654
  330. [    1.869130] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000
  331. [    1.869135] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000
  332. [    1.869144] console [netcon0] enabled
  333. [    1.869174] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
  334. [    1.869215] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  335. [    1.869221] mmc0: gated MCI clock
  336. [    1.869228] mmc0: starting CMD5 arg 00000000 flags 000002e1
  337. [    1.869231] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  338. [    1.869238] mmc0: ungated MCI clock
  339. [    1.869251] mmc0: req failed (CMD5): -123, retrying...
  340. [    1.869261] mmc0: req failed (CMD5): -123, retrying...
  341. [    1.869270] mmc0: req failed (CMD5): -123, retrying...
  342. [    1.869281] mmc0: req done (CMD5): -123: 00000000 00000000 00000000 00000000
  343. [    1.869286] mmc0: starting CMD55 arg 00000000 flags 000000f5
  344. [    1.869300] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  345. [    1.869303] mmc0: starting CMD55 arg 00000000 flags 000000f5
  346. [    1.869317] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  347. [    1.869320] mmc0: starting CMD55 arg 00000000 flags 000000f5
  348. [    1.869334] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  349. [    1.869337] mmc0: starting CMD55 arg 00000000 flags 000000f5
  350. [    1.869350] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  351. [    1.869355] mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
  352. [    1.869360] mmc0: starting CMD1 arg 00000000 flags 000000e1
  353. [    1.869374] mmc0: req done (CMD1): -123: 00000000 00000000 00000000 00000000
  354. [    1.869378] mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
  355. [    1.870437] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
  356. [    1.870440] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
  357. [    1.875164] mmc0: mmc_rescan_try_freq: trying to init card at 300000 Hz
  358. [    1.875180] netconsole: network logging started
  359. [    1.875184] hub 1-0:1.0: state 7 ports 6 chg 0006 evt 0000
  360. [    1.875191] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
  361. [    1.878413] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 0 timing 0
  362. [    1.889057] mmc0: clock 300000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  363. [    1.901052] mmc0: starting CMD52 arg 00000c00 flags 00000195
  364. [    1.901076] mmc0: req done (CMD52): -123: 00000000 00000000 00000000 00000000
  365. [    1.901116] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  366. [    1.901124] mmc0: gated MCI clock
  367. [    1.901129] mmc0: starting CMD52 arg 80000c08 flags 00000195
  368. [    1.901134] mmc0: clock 300000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  369. [    1.901143] mmc0: ungated MCI clock
  370. [    1.901160] mmc0: req done (CMD52): -123: 00000000 00000000 00000000 00000000
  371. [    1.901199] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  372. [    1.901211] mmc0: gated MCI clock
  373. [    1.901215] mmc0: clock 300000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  374. [    1.901223] mmc0: ungated MCI clock
  375. [    1.901225] mmc0: clock 300000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  376. [    1.901265] mmc0: clock 0Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  377. [    1.901270] mmc0: gated MCI clock
  378. [    1.903059] mmc0: starting CMD0 arg 00000000 flags 000000c0
  379. [    1.903065] mmc0: clock 300000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  380. [    1.903074] mmc0: ungated MCI clock
  381. [    1.903090] mmc0: req done (CMD0): -123: 00000000 00000000 00000000 00000000
  382. [    1.903130] mmc0: clock 0Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  383. [    1.903137] mmc0: gated MCI clock
  384. [    1.905050] mmc0: clock 300000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  385. [    1.905059] mmc0: ungated MCI clock
  386. [    1.905064] mmc0: clock 300000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  387. [    1.905107] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  388. [    1.905114] mmc0: gated MCI clock
  389. [    1.907060] mmc0: starting CMD8 arg 000001aa flags 000002f5
  390. [    1.907066] mmc0: clock 300000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  391. [    1.907074] mmc0: ungated MCI clock
  392. [    1.907091] mmc0: req done (CMD8): -123: 00000000 00000000 00000000 00000000
  393. [    1.907131] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  394. [    1.907138] mmc0: gated MCI clock
  395. [    1.907143] mmc0: starting CMD5 arg 00000000 flags 000002e1
  396. [    1.907148] mmc0: clock 300000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  397. [    1.907157] mmc0: ungated MCI clock
  398. [    1.907172] mmc0: req failed (CMD5): -123, retrying...
  399. [    1.907185] mmc0: req failed (CMD5): -123, retrying...
  400. [    1.907197] mmc0: req failed (CMD5): -123, retrying...
  401. [    1.907215] mmc0: req done (CMD5): -123: 00000000 00000000 00000000 00000000
  402. [    1.907251] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  403. [    1.907256] mmc0: gated MCI clock
  404. [    1.907260] mmc0: clock 300000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  405. [    1.907268] mmc0: ungated MCI clock
  406. [    1.907271] mmc0: starting CMD55 arg 00000000 flags 000000f5
  407. [    1.907285] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  408. [    1.907321] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  409. [    1.907326] mmc0: gated MCI clock
  410. [    1.907329] mmc0: starting CMD55 arg 00000000 flags 000000f5
  411. [    1.907332] mmc0: clock 300000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  412. [    1.907339] mmc0: ungated MCI clock
  413. [    1.907353] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  414. [    1.907388] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  415. [    1.907394] mmc0: gated MCI clock
  416. [    1.907397] mmc0: starting CMD55 arg 00000000 flags 000000f5
  417. [    1.907399] mmc0: clock 300000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  418. [    1.907407] mmc0: ungated MCI clock
  419. [    1.907419] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  420. [    1.907455] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  421. [    1.907460] mmc0: gated MCI clock
  422. [    1.907463] mmc0: starting CMD55 arg 00000000 flags 000000f5
  423. [    1.907466] mmc0: clock 300000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  424. [    1.907473] mmc0: ungated MCI clock
  425. [    1.907487] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  426. [    1.907522] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  427. [    1.907528] mmc0: gated MCI clock
  428. [    1.907531] mmc0: clock 300000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  429. [    1.907539] mmc0: ungated MCI clock
  430. [    1.907541] mmc0: clock 300000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
  431. [    1.907548] mmc0: starting CMD1 arg 00000000 flags 000000e1
  432. [    1.907563] mmc0: req done (CMD1): -123: 00000000 00000000 00000000 00000000
  433. [    1.907598] mmc0: clock 0Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
  434. [    1.907604] mmc0: gated MCI clock
  435. [    1.907607] mmc0: clock 300000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
  436. [    1.907615] mmc0: ungated MCI clock
  437. [    1.907617] mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
  438. [    1.909049] mmc0: mmc_rescan_try_freq: trying to init card at 200000 Hz
  439. [    1.910599] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 0 timing 0
  440. [    1.921062] mmc0: clock 200000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  441. [    1.926015] ata1.00: ATA-8: WDC WD2500BEVS-08VAT2, 14.01A14, max UDMA/133
  442. [    1.926299] ehci_hcd 0000:00:1a.7: port 1 full speed --> companion
  443. [    1.926303] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 003801 0  ACK POWER OWNER sig=j CONNECT
  444. [    1.926307] hub 1-0:1.0: port 1 not reset yet, waiting 50ms
  445. [    1.927470] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
  446. [    1.929148] ata1.00: failed to get Identify Device Data, Emask 0x1
  447. [    1.931200] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
  448. [    1.932680] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
  449. [    1.934193] mmc0: starting CMD52 arg 00000c00 flags 00000195
  450. [    1.934210] mmc0: req done (CMD52): -123: 00000000 00000000 00000000 00000000
  451. [    1.934233] mmc0: starting CMD52 arg 80000c08 flags 00000195
  452. [    1.934263] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  453. [    1.934268] mmc0: gated MCI clock
  454. [    1.934296] mmc0: clock 200000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  455. [    1.934305] mmc0: ungated MCI clock
  456. [    1.934322] mmc0: req done (CMD52): -123: 00000000 00000000 00000000 00000000
  457. [    1.934374] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  458. [    1.934379] mmc0: gated MCI clock
  459. [    1.934384] mmc0: clock 200000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  460. [    1.934391] mmc0: ungated MCI clock
  461. [    1.934394] mmc0: clock 200000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  462. [    1.934450] mmc0: clock 0Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  463. [    1.934456] mmc0: gated MCI clock
  464. [    1.934577] ata1.00: failed to get Identify Device Data, Emask 0x1
  465. [    1.934581] ata1.00: configured for UDMA/133
  466. [    1.936052] mmc0: starting CMD0 arg 00000000 flags 000000c0
  467. [    1.936055] mmc0: clock 200000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  468. [    1.936063] mmc0: ungated MCI clock
  469. [    1.936077] mmc0: req done (CMD0): -123: 00000000 00000000 00000000 00000000
  470. [    1.936129] mmc0: clock 0Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  471. [    1.936135] mmc0: gated MCI clock
  472. [    1.936144] scsi 0:0:0:0: Direct-Access     ATA      WDC WD2500BEVS-0 14.0 PQ: 0 ANSI: 5
  473. [    1.937957] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
  474. [    1.939451] mmc0: clock 200000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  475. [    1.939459] mmc0: ungated MCI clock
  476. [    1.939462] mmc0: clock 200000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  477. [    1.939491] sd 0:0:0:0: [sda] Write Protect is off
  478. [    1.939518] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  479. [    1.939523] mmc0: gated MCI clock
  480. [    1.939610] sd 0:0:0:0: Attached scsi generic sg0 type 0
  481. [    1.941036] mmc0: starting CMD8 arg 000001aa flags 000002f5
  482. [    1.941038] mmc0: clock 200000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  483. [    1.941046] mmc0: ungated MCI clock
  484. [    1.941060] mmc0: req done (CMD8): -123: 00000000 00000000 00000000 00000000
  485. [    1.941112] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  486. [    1.941117] mmc0: gated MCI clock
  487. [    1.941123] mmc0: starting CMD5 arg 00000000 flags 000002e1
  488. [    1.941125] mmc0: clock 200000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  489. [    1.941132] mmc0: ungated MCI clock
  490. [    1.941144] mmc0: req failed (CMD5): -123, retrying...
  491. [    1.941154] mmc0: req failed (CMD5): -123, retrying...
  492. [    1.941164] mmc0: req failed (CMD5): -123, retrying...
  493. [    1.941176] mmc0: req done (CMD5): -123: 00000000 00000000 00000000 00000000
  494. [    1.941180] mmc0: starting CMD55 arg 00000000 flags 000000f5
  495. [    1.941194] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  496. [    1.941197] mmc0: starting CMD55 arg 00000000 flags 000000f5
  497. [    1.941210] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  498. [    1.941261] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  499. [    1.941266] mmc0: gated MCI clock
  500. [    1.941268] mmc0: starting CMD55 arg 00000000 flags 000000f5
  501. [    1.941270] mmc0: clock 200000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  502. [    1.941278] mmc0: ungated MCI clock
  503. [    1.941290] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  504. [    1.941294] mmc0: starting CMD55 arg 00000000 flags 000000f5
  505. [    1.941307] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  506. [    1.941312] mmc0: clock 200000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
  507. [    1.941317] mmc0: starting CMD1 arg 00000000 flags 000000e1
  508. [    1.941330] mmc0: req done (CMD1): -123: 00000000 00000000 00000000 00000000
  509. [    1.941334] mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
  510. [    1.942389] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
  511. [    1.942414] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
  512. [    1.943016] mmc0: mmc_rescan_try_freq: trying to init card at 195312 Hz
  513. [    1.943018] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 0 timing 0
  514. [    1.954204] mmc0: clock 195312Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  515. [    1.966063] mmc0: starting CMD52 arg 00000c00 flags 00000195
  516. [    1.966084] mmc0: req done (CMD52): -123: 00000000 00000000 00000000 00000000
  517. [    1.966114] mmc0: starting CMD52 arg 80000c08 flags 00000195
  518. [    1.966141] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  519. [    1.966148] mmc0: gated MCI clock
  520. [    1.966178] mmc0: clock 195312Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  521. [    1.966187] mmc0: ungated MCI clock
  522. [    1.966211] mmc0: req done (CMD52): -123: 00000000 00000000 00000000 00000000
  523. [    1.966266] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  524. [    1.966271] mmc0: gated MCI clock
  525. [    1.966294] mmc0: clock 195312Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  526. [    1.966301] mmc0: ungated MCI clock
  527. [    1.966304] mmc0: clock 195312Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  528. [    1.966360] mmc0: clock 0Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  529. [    1.966366] mmc0: gated MCI clock
  530. [    1.968016] mmc0: starting CMD0 arg 00000000 flags 000000c0
  531. [    1.968019] mmc0: clock 195312Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  532. [    1.968029] mmc0: ungated MCI clock
  533. [    1.968043] mmc0: req done (CMD0): -123: 00000000 00000000 00000000 00000000
  534. [    1.968097] mmc0: clock 0Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  535. [    1.968102] mmc0: gated MCI clock
  536. [    1.970078] mmc0: clock 195312Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
  537. [    1.970087] mmc0: ungated MCI clock
  538. [    1.970092] mmc0: clock 195312Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  539. [    1.970153] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  540. [    1.970160] mmc0: gated MCI clock
  541. [    1.972047] mmc0: starting CMD8 arg 000001aa flags 000002f5
  542. [    1.972052] mmc0: clock 195312Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  543. [    1.972061] mmc0: ungated MCI clock
  544. [    1.972079] mmc0: req done (CMD8): -123: 00000000 00000000 00000000 00000000
  545. [    1.972108] mmc0: starting CMD5 arg 00000000 flags 000002e1
  546. [    1.972137] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  547. [    1.972144] mmc0: gated MCI clock
  548. [    1.972173] mmc0: clock 195312Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  549. [    1.972182] mmc0: ungated MCI clock
  550. [    1.972221] mmc0: req failed (CMD5): -123, retrying...
  551. [    1.972251] mmc0: req failed (CMD5): -123, retrying...
  552. [    1.972279] mmc0: req failed (CMD5): -123, retrying...
  553. [    1.972292] mmc0: req done (CMD5): -123: 00000000 00000000 00000000 00000000
  554. [    1.972345] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  555. [    1.972351] mmc0: gated MCI clock
  556. [    1.972373] mmc0: clock 195312Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  557. [    1.972380] mmc0: ungated MCI clock
  558. [    1.972384] mmc0: starting CMD55 arg 00000000 flags 000000f5
  559. [    1.972398] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  560. [    1.972420] mmc0: starting CMD55 arg 00000000 flags 000000f5
  561. [    1.972451] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  562. [    1.972456] mmc0: gated MCI clock
  563. [    1.972478] mmc0: clock 195312Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  564. [    1.972486] mmc0: ungated MCI clock
  565. [    1.972500] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  566. [    1.972522] mmc0: starting CMD55 arg 00000000 flags 000000f5
  567. [    1.972553] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  568. [    1.972559] mmc0: gated MCI clock
  569. [    1.972581] mmc0: clock 195312Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  570. [    1.972588] mmc0: ungated MCI clock
  571. [    1.972602] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  572. [    1.972624] mmc0: starting CMD55 arg 00000000 flags 000000f5
  573. [    1.972655] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  574. [    1.972661] mmc0: gated MCI clock
  575. [    1.972683] mmc0: clock 195312Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  576. [    1.972691] mmc0: ungated MCI clock
  577. [    1.972705] mmc0: req done (CMD55): -123: 00000000 00000000 00000000 00000000
  578. [    1.972758] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  579. [    1.972764] mmc0: gated MCI clock
  580. [    1.972775] mmc0: clock 195312Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
  581. [    1.972783] mmc0: ungated MCI clock
  582. [    1.972785] mmc0: clock 195312Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
  583. [    1.972792] mmc0: starting CMD1 arg 00000000 flags 000000e1
  584. [    1.972806] mmc0: req done (CMD1): -123: 00000000 00000000 00000000 00000000
  585. [    1.972859] mmc0: clock 0Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
  586. [    1.972865] mmc0: gated MCI clock
  587. [    1.972887] mmc0: clock 195312Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
  588. [    1.972895] mmc0: ungated MCI clock
  589. [    1.972897] mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
  590. [    1.974019] mmc0: frequency set to 0 in disable function, this means the clock is already disabled.
  591. [    1.977043] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 003002 0  ACK POWER OWNER sig=se0 CSC
  592. [    1.977066] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
  593. [    1.984148]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
  594. [    1.986516] sd 0:0:0:0: [sda] Attached SCSI disk
  595. [    2.028300] ehci_hcd 0000:00:1a.7: port 2 reset complete, port enabled
  596. [    2.028305] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 001005 0  ACK POWER sig=se0 PE CONNECT
  597. [    2.079024] usb 1-2: new high-speed USB device number 3 using ehci_hcd
  598. [    2.138297] ehci_hcd 0000:00:1a.7: port 2 reset complete, port enabled
  599. [    2.138302] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 001005 0  ACK POWER sig=se0 PE CONNECT
  600. [    2.244064] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
  601. [    2.248473] ata2.00: unexpected _GTF length (8)
  602. [    2.249989] ata2.00: ATAPI: HL-DT-STDVDRAM GT30N, LG09, max UDMA/66
  603. [    2.254451] ata2.00: unexpected _GTF length (8)
  604. [    2.255953] ata2.00: configured for UDMA/66
  605. [    2.260325] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVDRAM GT30N     LG09 PQ: 0 ANSI: 5
  606. [    2.266366] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
  607. [    2.268037] cdrom: Uniform CD-ROM driver Revision: 3.20
  608. [    2.269812] sr 1:0:0:0: Attached scsi CD-ROM sr0
  609. [    2.269928] sr 1:0:0:0: Attached scsi generic sg1 type 5
  610. [    1.939743] ACPI: Invalid Power Resource to register!
  611. [    2.271655] ACPI: Invalid Power Resource to register!<7>[    2.409618] usb 1-2: skipped 1 descriptor after configuration
  612. [    2.409624] usb 1-2: skipped 8 descriptors after interface
  613. [    2.409629] usb 1-2: skipped 1 descriptor after endpoint
  614. [    2.409634] usb 1-2: skipped 43 descriptors after interface
  615. [    2.409644] usb 1-2: skipped 1 descriptor after endpoint
  616. [    2.409649] usb 1-2: skipped 4 descriptors after interface
  617. [    2.409654] usb 1-2: skipped 2 descriptors after interface
  618. [    2.409658] usb 1-2: skipped 1 descriptor after endpoint
  619. [    2.409663] usb 1-2: skipped 2 descriptors after interface
  620. [    2.409667] usb 1-2: skipped 1 descriptor after endpoint
  621. [    2.409672] usb 1-2: skipped 2 descriptors after interface
  622. [    2.409676] usb 1-2: skipped 1 descriptor after endpoint
  623. [    2.409681] usb 1-2: skipped 2 descriptors after interface
  624. [    2.409685] usb 1-2: skipped 1 descriptor after endpoint
  625. [    2.411464] usb 1-2: default language 0x0409
  626. [    2.414214] usb 1-2: USB interface quirks for this device: 2
  627. [    2.414219] usb 1-2: udev 3, busnum 1, minor = 2
  628. [    2.414224] usb 1-2: New USB device found, idVendor=046d, idProduct=0825
  629. [    2.415913] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=2
  630. [    2.417512] usb 1-2: SerialNumber: 7FB61E10
  631. [    2.419213] usb 1-2: usb_probe_device
  632. [    2.419217] usb 1-2: configuration #1 chosen from 1 choice
  633. [    2.419318] usb 1-2: adding 1-2:1.0 (config #1, interface 0)
  634. [    2.419435] usb 1-2: adding 1-2:1.1 (config #1, interface 1)
  635. [    2.419530] usb 1-2: adding 1-2:1.2 (config #1, interface 2)
  636. [    2.419622] usb 1-2: adding 1-2:1.3 (config #1, interface 3)
  637. [    2.419732] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002
  638. [    2.419742] uhci_hcd 0000:00:1a.0: port 1 portsc 0093,00
  639. [    2.419749] hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
  640. [    2.523056] hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
  641. [    2.576063] ata5: SATA link down (SStatus 0 SControl 300)
  642. [    2.625049] usb 3-1: new full-speed USB device number 2 using uhci_hcd
  643. [    2.704041] usb usb4: suspend_rh (auto-stop)
  644. [    2.747114] usb 3-1: ep0 maxpacket = 8
  645. [    2.768242] usb 3-1: skipped 1 descriptor after interface
  646. [    2.768248] usb 3-1: skipped 1 descriptor after interface
  647. [    2.771238] usb 3-1: default language 0x0409
  648. [    2.783175] usb 3-1: udev 2, busnum 3, minor = 257
  649. [    2.783179] usb 3-1: New USB device found, idVendor=09da, idProduct=9090
  650. [    2.784834] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
  651. [    2.786452] usb 3-1: Product: USB Device
  652. [    2.788080] usb 3-1: Manufacturer: A4TECH
  653. [    2.789722] usb 3-1: usb_probe_device
  654. [    2.789725] usb 3-1: configuration #1 chosen from 1 choice
  655. [    2.792244] usb 3-1: adding 3-1:1.0 (config #1, interface 0)
  656. [    2.792299] usbhid 3-1:1.0: usb_probe_interface
  657. [    2.792302] usbhid 3-1:1.0: usb_probe_interface - got id
  658. [    2.799968] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1:1.0/input/input6
  659. [    2.801636] uhci_hcd 0000:00:1a.0: reserve dev 2 ep81-INT, period 1, phase 0, 20 us
  660. [    2.801800] usbhid 3-1:1.0: looking for a minor, starting at 96
  661. [    2.801973] hid-generic 0003:09DA:9090.0001: input,hiddev0,hidraw0: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:00:1a.0-1/input0
  662. [    2.803703] usb 3-1: adding 3-1:1.1 (config #1, interface 1)
  663. [    2.803777] usbhid 3-1:1.1: usb_probe_interface
  664. [    2.803780] usbhid 3-1:1.1: usb_probe_interface - got id
  665. [    2.805543] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1:1.1/input/input7
  666. [    2.807548] hid-generic 0003:09DA:9090.0002: input,hidraw1: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:00:1a.0-1/input1
  667. [    2.809400] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0002
  668. [    2.809409] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 003002 0  ACK POWER OWNER sig=se0 CSC
  669. [    2.809417] hub 1-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
  670. [    2.883067] ata6: SATA link down (SStatus 0 SControl 300)
  671. [    2.913136] hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
  672. [    2.954039] usb usb5: suspend_rh (auto-stop)
  673. [    2.954065] usb usb6: suspend_rh (auto-stop)
  674. [    2.954090] usb usb7: suspend_rh (auto-stop)
  675. [    2.954114] usb usb8: suspend_rh (auto-stop)
  676. [    3.004843] psmouse serio4: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd047b3/0xb40000/0xa0000, board id: 71, fw id: 578367
  677. [    3.006816] psmouse serio4: synaptics: serio: Synaptics pass-through port at isa0060/serio4/input0
  678. [    3.056022] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8
  679. [    3.060584] md: Skipping autodetection of RAID arrays. (raid=autodetect will force)
  680. [    3.141999] kjournald starting.  Commit interval 5 seconds
  681. [    3.142048] EXT3-fs (sda2): mounted filesystem with writeback data mode
  682. [    3.142056] VFS: Mounted root (ext3 filesystem) readonly on device 8:2.
  683. [    3.147728] Freeing unused kernel memory: 440k freed
  684. [    3.149829] Write protecting the kernel text: 5580k
  685. [    3.151799] Write protecting the kernel read-only data: 2212k
  686. [    3.766043] hub 2-0:1.0: hub_suspend
  687. [    3.766051] usb usb2: bus auto-suspend, wakeup 1
  688. [    3.766054] ehci_hcd 0000:00:1d.7: suspend root hub
  689. [    3.800017] hub 4-0:1.0: hub_suspend
  690. [    3.800022] usb usb4: bus auto-suspend, wakeup 1
  691. [    3.800025] usb usb4: suspend_rh
  692. [    3.815125] hub 5-0:1.0: hub_suspend
  693. [    3.815131] usb usb5: bus auto-suspend, wakeup 1
  694. [    3.815134] usb usb5: suspend_rh
  695. [    3.832018] hub 6-0:1.0: hub_suspend
  696. [    3.832023] usb usb6: bus auto-suspend, wakeup 1
  697. [    3.832026] usb usb6: suspend_rh
  698. [    3.869069] hub 7-0:1.0: hub_suspend
  699. [    3.869077] usb usb7: bus auto-suspend, wakeup 1
  700. [    3.869081] usb usb7: suspend_rh
  701. [    3.869108] hub 8-0:1.0: hub_suspend
  702. [    3.869114] usb usb8: bus auto-suspend, wakeup 1
  703. [    3.869118] usb usb8: suspend_rh
  704. [    4.293094] kbd_mode (1143) used greatest stack depth: 6740 bytes left
  705. [    4.345100] loadkeys (1144) used greatest stack depth: 5904 bytes left
  706. [    4.347149] init-early.sh (1142) used greatest stack depth: 5668 bytes left
  707. [    6.068416] udevd[1253]: starting version 171
  708. [    7.118068] snd_hda_intel 0000:00:1b.0: irq 50 for MSI/MSI-X
  709. [    9.041250] psmouse serio5: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 3/3
  710. [    9.064600] vboxdrv: Found 2 processor cores.
  711. [    9.064760] vboxdrv: fAsync=0 offMin=0x217 offMax=0x6f9
  712. [    9.064821] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
  713. [    9.064822] vboxdrv: Successfully loaded version 4.2.4 (interface 0x001a0004).
  714. [    9.289870] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio4/serio5/input/input9
  715. [    9.897762] EXT3-fs (sda2): using internal journal
  716. [   10.064979] Adding 3156736k swap on /dev/sda5.  Priority:-1 extents:1 across:3156736k
  717. [   10.291743] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
  718. [   10.380876] kjournald starting.  Commit interval 5 seconds
  719. [   10.381167] EXT3-fs (sda7): using internal journal
  720. [   10.381170] EXT3-fs (sda7): mounted filesystem with writeback data mode
  721. [   11.528020] i2c i2c-1: master_xfer[0] W, addr=0x50, len=1
  722. [   11.528025] i2c i2c-1: master_xfer[1] R, addr=0x50, len=1
  723. [   11.530062] i2c i2c-1: master_xfer[0] W, addr=0x50, len=1
  724. [   11.530067] i2c i2c-1: master_xfer[1] R, addr=0x50, len=1
  725. [   11.530307] i2c i2c-1: NAK from device addr 0x50 msg #0
  726. [   16.347501] iwl3945 0000:03:00.0: loaded firmware version 15.32.2.9
  727. [   16.414479] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
  728. [   16.528421] r8169 0000:08:00.0 eth0: link down
  729. [   16.528457] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  730. [   19.534199] fuse init (API version 7.20)
  731. [   30.872136] i2c i2c-1: master_xfer[0] W, addr=0x50, len=1
  732. [   30.872143] i2c i2c-1: master_xfer[1] R, addr=0x50, len=1
  733. [   30.875129] i2c i2c-1: master_xfer[0] W, addr=0x50, len=1
  734. [   30.875136] i2c i2c-1: master_xfer[1] R, addr=0x50, len=1
  735. [   30.875375] i2c i2c-1: NAK from device addr 0x50 msg #0
  736. [   30.883107] i2c i2c-1: master_xfer[0] W, addr=0x50, len=1
  737. [   30.883112] i2c i2c-1: master_xfer[1] R, addr=0x50, len=1
  738. [   30.885027] i2c i2c-1: master_xfer[0] W, addr=0x50, len=1
  739. [   30.885033] i2c i2c-1: master_xfer[1] R, addr=0x50, len=1
  740. [   30.885271] i2c i2c-1: NAK from device addr 0x50 msg #0
  741. [   30.918136] i2c i2c-1: master_xfer[0] W, addr=0x50, len=1
  742. [   30.918142] i2c i2c-1: master_xfer[1] R, addr=0x50, len=1
  743. [   30.920028] i2c i2c-1: master_xfer[0] W, addr=0x50, len=1
  744. [   30.920034] i2c i2c-1: master_xfer[1] R, addr=0x50, len=1
  745. [   30.920272] i2c i2c-1: NAK from device addr 0x50 msg #0
  746. [   30.928135] i2c i2c-1: master_xfer[0] W, addr=0x50, len=1
  747. [   30.928141] i2c i2c-1: master_xfer[1] R, addr=0x50, len=1
  748. [   30.930029] i2c i2c-1: master_xfer[0] W, addr=0x50, len=1
  749. [   30.930035] i2c i2c-1: master_xfer[1] R, addr=0x50, len=1
  750. [   30.930273] i2c i2c-1: NAK from device addr 0x50 msg #0
  751. [   31.994724] uhci_hcd 0000:00:1a.0: reserve dev 2 ep82-INT, period 1, phase 0, 17 us
  752. [   40.904028] i2c i2c-1: master_xfer[0] W, addr=0x50, len=1
  753. [   40.904033] i2c i2c-1: master_xfer[1] R, addr=0x50, len=1
  754. [   40.906019] i2c i2c-1: master_xfer[0] W, addr=0x50, len=1
  755. [   40.906022] i2c i2c-1: master_xfer[1] R, addr=0x50, len=1
  756. [   40.906254] i2c i2c-1: NAK from device addr 0x50 msg #0
  757. [   70.642711] wlan0: authenticate with 00:0e:2e:fa:be:6d
  758. [   70.645613] wlan0: send auth to 00:0e:2e:fa:be:6d (try 1/3)
  759. [   70.648568] wlan0: authenticated
  760. [   70.648718] iwl3945 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
  761. [   70.648724] iwl3945 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
  762. [   70.649053] wlan0: associate with 00:0e:2e:fa:be:6d (try 1/3)
  763. [   70.664389] wlan0: RX AssocResp from 00:0e:2e:fa:be:6d (capab=0x411 status=0 aid=1)
  764. [   70.666126] wlan0: associated
  765. [   70.666157] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
  766. [  422.560513] hda-intel: spurious response 0x0:0x0, last cmd=0x835021
  767. [  422.731888] hda-intel: spurious response 0x0:0x0, last cmd=0x339025
  768. [  534.731421] hda-intel: spurious response 0x0:0x0, last cmd=0x339024
  769. [  534.950161] hda-intel: spurious response 0x0:0x0, last cmd=0x339026
  770. [  535.243847] hda-intel: spurious response 0x0:0x0, last cmd=0x339027
  771. [  535.539429] hda-intel: spurious response 0x0:0x0, last cmd=0x339027
  772. [  535.572735] hda-intel: spurious response 0x0:0x0, last cmd=0x339027
  773. [  535.610889] hda-intel: spurious response 0x0:0x0, last cmd=0x339027
  774. [  536.785951] hda-intel: spurious response 0x0:0x0, last cmd=0x339028
  775. [ 5570.472979] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
  776. [ 6916.600309] hda-intel: spurious response 0x0:0x0, last cmd=0x339028
  777. [ 6916.895958] hda-intel: spurious response 0x0:0x0, last cmd=0x339027
  778. [ 6917.058576] hda-intel: spurious response 0x0:0x0, last cmd=0x339026
  779. [ 6917.203310] hda-intel: spurious response 0x0:0x0, last cmd=0x339025
  780. [ 6917.327638] hda-intel: spurious response 0x0:0x0, last cmd=0x339024
  781. [ 6917.454427] hda-intel: spurious response 0x0:0x0, last cmd=0x339023
  782. [ 6917.625315] hda-intel: spurious response 0x0:0x0, last cmd=0x339022
  783. [ 6917.772300] hda-intel: spurious response 0x0:0x0, last cmd=0x339021
  784. [ 6917.936009] hda-intel: spurious response 0x0:0x0, last cmd=0x339020
  785. [ 6918.098422] hda-intel: spurious response 0x0:0x0, last cmd=0x33901e
  786. [ 6918.322328] hda-intel: spurious response 0x0:0x0, last cmd=0x33901e
  787. [ 6965.960438] hda-intel: spurious response 0x0:0x0, last cmd=0x33901d
  788. [ 6966.140944] hda-intel: spurious response 0x0:0x0, last cmd=0x33901b
  789. [ 6966.317349] hda-intel: spurious response 0x0:0x0, last cmd=0x33901b
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
 
Top