sakthikrishnabala

Kernel Bootlogs

Feb 6th, 2020
118
0
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 52.00 KB | None | 0 0
  1. [ 0.000000] Booting Linux on physical CPU 0x0
  2. [ 0.000000] Linux version 4.14.0-qcomlt-arm64 (root@user) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #7 SMP PREEMPT Wed Feb 5 16:17:29 IST 2020
  3. [ 0.000000] Boot CPU: AArch64 Processor [512f2011]
  4. [ 0.000000] Machine model: 820 Nano SoM Commando Board
  5. [ 0.000000] efi: Getting EFI parameters from FDT:
  6. [ 0.000000] efi: UEFI not found.
  7. [ 0.000000] Reserved memory: created DMA memory pool at 0x0000000090b00000, size 10 MiB
  8. [ 0.000000] OF: reserved mem: initialized node gpu@8f200000, compatible id shared-dma-pool
  9. [ 0.000000] cma: Reserved 16 MiB at 0x00000000ff000000
  10. [ 0.000000] NUMA: No NUMA configuration found
  11. [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000017e44ffff]
  12. [ 0.000000] NUMA: NODE_DATA [mem 0x17e3d5080-0x17e3d6b7f]
  13. [ 0.000000] Zone ranges:
  14. [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff]
  15. [ 0.000000] Normal [mem 0x0000000100000000-0x000000017e44ffff]
  16. [ 0.000000] Movable zone start for each node
  17. [ 0.000000] Early memory node ranges
  18. [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000857fffff]
  19. [ 0.000000] node 0: [mem 0x0000000091700000-0x00000000a1dfffff]
  20. [ 0.000000] node 0: [mem 0x00000000a2000000-0x000000017e44ffff]
  21. [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000017e44ffff]
  22. [ 0.000000] On node 0 totalpages: 992080
  23. [ 0.000000] DMA zone: 7420 pages used for memmap
  24. [ 0.000000] DMA zone: 0 pages reserved
  25. [ 0.000000] DMA zone: 474880 pages, LIFO batch:31
  26. [ 0.000000] Normal zone: 8082 pages used for memmap
  27. [ 0.000000] Normal zone: 517200 pages, LIFO batch:31
  28. [ 0.000000] psci: probing for conduit method from DT.
  29. [ 0.000000] psci: PSCIv1.0 detected in firmware.
  30. [ 0.000000] psci: Using standard PSCI v0.2 function IDs
  31. [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
  32. [ 0.000000] psci: SMC Calling Convention v1.0
  33. [ 0.000000] percpu: Embedded 24 pages/cpu @ffff8000fe370000 s57496 r8192 d32616 u98304
  34. [ 0.000000] pcpu-alloc: s57496 r8192 d32616 u98304 alloc=24*4096
  35. [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
  36. [ 0.000000] Detected PIPT I-cache on CPU0
  37. [ 0.000000] CPU features: enabling workaround for Qualcomm Technologies Kryo erratum 1003
  38. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 976578
  39. [ 0.000000] Policy zone: Normal
  40. [ 0.000000] Kernel command line: root=/dev/disk/by-partlabel/rootfs rw rootwait console=tty0 console=ttyMSM0,115200n8 androidboot.bootdevice=624000.ufshc androidboot.verifiedbootstate=orange androidboot.veritymode=enforcing androidboot.serialno=44699ae2 androidboot.baseband=apq mdss_mdp.panel=0 fpsimd.fpsimd_settings=0 app_setting.use_app_setting=0
  41. [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
  42. [ 0.000000] software IO TLB: mapped [mem 0xfafff000-0xfefff000] (64MB)
  43. [ 0.000000] Memory: 3798564K/3968320K available (10108K kernel code, 1216K rwdata, 4248K rodata, 704K init, 392K bss, 153372K reserved, 16384K cma-reserved)
  44. [ 0.000000] Virtual kernel memory layout:
  45. [ 0.000000] modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB)
  46. [ 0.000000] vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000 (129022 GB)
  47. [ 0.000000] .text : 0xffff000008080000 - 0xffff000008a60000 ( 10112 KB)
  48. [ 0.000000] .rodata : 0xffff000008a60000 - 0xffff000008e90000 ( 4288 KB)
  49. [ 0.000000] .init : 0xffff000008e90000 - 0xffff000008f40000 ( 704 KB)
  50. [ 0.000000] .data : 0xffff000008f40000 - 0xffff000009070200 ( 1217 KB)
  51. [ 0.000000] .bss : 0xffff000009070200 - 0xffff0000090d22c0 ( 393 KB)
  52. [ 0.000000] fixed : 0xffff7dfffe7f9000 - 0xffff7dfffec00000 ( 4124 KB)
  53. [ 0.000000] PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000 ( 16 MB)
  54. [ 0.000000] vmemmap : 0xffff7e0000000000 - 0xffff800000000000 ( 2048 GB maximum)
  55. [ 0.000000] 0xffff7e0000000000 - 0xffff7e0003f91400 ( 63 MB actual)
  56. [ 0.000000] memory : 0xffff800000000000 - 0xffff8000fe450000 ( 4068 MB)
  57. [ 0.000000] SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  58. [ 0.000000] Preemptible hierarchical RCU implementation.
  59. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
  60. [ 0.000000] Tasks RCU enabled.
  61. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
  62. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
  63. [ 0.000000] GICv3: VLPI support, no direct LPI support
  64. [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000009c00000
  65. [ 0.000000] GICv2m: range[mem 0x09bd0000-0x09bd0fff], SPI[544:639]
  66. [ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
  67. [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
  68. [ 0.000003] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
  69. [ 0.000306] Console: colour dummy device 80x25
  70. [ 0.000802] console [tty0] enabled
  71. [ 0.000856] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800)
  72. [ 0.000877] pid_max: default: 32768 minimum: 301
  73. [ 0.000945] Security Framework initialized
  74. [ 0.001765] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
  75. [ 0.002208] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
  76. [ 0.002284] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
  77. [ 0.002311] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
  78. [ 0.015725] ASID allocator initialised with 32768 entries
  79. [ 0.023723] Hierarchical SRCU implementation.
  80. [ 0.033324] EFI services will not be available.
  81. [ 0.039798] smp: Bringing up secondary CPUs ...
  82. [ 0.068331] Detected PIPT I-cache on CPU1
  83. [ 0.068358] GICv3: CPU1: found redistributor 1 region 0:0x0000000009c40000
  84. [ 0.068390] CPU1: Booted secondary processor [512f2011]
  85. [ 0.099033] Detected PIPT I-cache on CPU2
  86. [ 0.099866] GICv3: CPU2: found redistributor 100 region 0:0x0000000009c80000
  87. [ 0.100640] CPU2: Booted secondary processor [512f2051]
  88. [ 0.134751] Detected PIPT I-cache on CPU3
  89. [ 0.135576] GICv3: CPU3: found redistributor 101 region 0:0x0000000009cc0000
  90. [ 0.136294] CPU3: Booted secondary processor [512f2051]
  91. [ 0.139668] smp: Brought up 1 node, 4 CPUs
  92. [ 0.139764] SMP: Total of 4 processors activated.
  93. [ 0.139784] CPU features: detected feature: GIC system register CPU interface
  94. [ 0.139799] CPU features: detected feature: 32-bit EL0 Support
  95. [ 0.139810] CPU features: detected feature: Kernel page table isolation (KPTI)
  96. [ 0.200118] CPU: All CPU(s) started at EL1
  97. [ 0.200798] alternatives: patching kernel code
  98. [ 0.203375] devtmpfs: initialized
  99. [ 0.212912] random: get_random_u32 called from bucket_table_alloc+0x108/0x258 with crng_init=0
  100. [ 0.213483] Registered cp15_barrier emulation handler
  101. [ 0.213593] Registered setend emulation handler
  102. [ 0.213875] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
  103. [ 0.213955] futex hash table entries: 1024 (order: 5, 131072 bytes)
  104. [ 0.214292] pinctrl core: initialized pinctrl subsystem
  105. [ 0.215292] DMI not present or invalid.
  106. [ 0.215570] NET: Registered protocol family 16
  107. [ 0.219126] cpuidle: using governor menu
  108. [ 0.220170] vdso: 2 pages (1 code @ ffff000008a66000, 1 data @ ffff000008f45000)
  109. [ 0.220304] hw-breakpoint: found 8 breakpoint and 4 watchpoint registers.
  110. [ 0.222804] DMA: preallocated 256 KiB pool for atomic allocations
  111. [ 0.223047] Serial: AMBA PL011 UART driver
  112. [ 0.261448] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
  113. [ 0.265374] ACPI: Interpreter disabled.
  114. [ 0.265835] reg-fixed-voltage soc:wlan-en-1-8v: could not find pctldev for node /soc/qcom,spmi@400f000/pmic@0/gpios@c000/wlan_en_gpios, deferring probe
  115. [ 0.266928] vgaarb: loaded
  116. [ 0.267168] SCSI subsystem initialized
  117. [ 0.268087] libata version 3.00 loaded.
  118. [ 0.268292] usbcore: registered new interface driver usbfs
  119. [ 0.268348] usbcore: registered new interface driver hub
  120. [ 0.268426] usbcore: registered new device driver usb
  121. [ 0.269201] pps_core: LinuxPPS API ver. 1 registered
  122. [ 0.269222] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  123. [ 0.269257] EDAC MC: Ver: 3.0.0
  124. [ 0.272190] dmi: Firmware registration failed.
  125. [ 0.276323] Advanced Linux Sound Architecture Driver Initialized.
  126. [ 0.278419] clocksource: Switched to clocksource arch_sys_counter
  127. [ 0.278546] VFS: Disk quotas dquot_6.6.0
  128. [ 0.278601] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
  129. [ 0.278757] pnp: PnP ACPI: disabled
  130. [ 0.285426] NET: Registered protocol family 2
  131. [ 0.286025] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
  132. [ 0.286377] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
  133. [ 0.286528] TCP: Hash tables configured (established 32768 bind 32768)
  134. [ 0.286700] UDP hash table entries: 2048 (order: 4, 65536 bytes)
  135. [ 0.286766] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
  136. [ 0.286939] NET: Registered protocol family 1
  137. [ 0.294063] s1: supplied by regulator-dummy
  138. [ 0.294291] s2: supplied by regulator-dummy
  139. [ 0.294442] s3: supplied by regulator-dummy
  140. [ 0.294479] s3: Bringing 0uV into 1300000-1300000uV
  141. [ 0.294711] s4: supplied by regulator-dummy
  142. [ 0.294749] s4: Bringing 0uV into 1800000-1800000uV
  143. [ 0.294966] s5: supplied by regulator-dummy
  144. [ 0.295004] s5: Bringing 0uV into 2150000-2150000uV
  145. [ 0.295230] s6: supplied by regulator-dummy
  146. [ 0.295391] s7: supplied by regulator-dummy
  147. [ 0.295428] s7: Bringing 0uV into 800000-800000uV
  148. [ 0.295672] s8: supplied by regulator-dummy
  149. [ 0.295819] s9: supplied by regulator-dummy
  150. [ 0.295982] s10: supplied by regulator-dummy
  151. [ 0.296138] s11: supplied by regulator-dummy
  152. [ 0.296294] s12: supplied by regulator-dummy
  153. [ 0.296458] l1: supplied by s3
  154. [ 0.296502] l1: Bringing 0uV into 1000000-1000000uV
  155. [ 0.296795] l2: supplied by s3
  156. [ 0.296835] l2: Bringing 0uV into 1250000-1250000uV
  157. [ 0.297073] l3: supplied by s3
  158. [ 0.297110] l3: Bringing 0uV into 850000-850000uV
  159. [ 0.297398] RPC: Registered named UNIX socket transport module.
  160. [ 0.297417] RPC: Registered udp transport module.
  161. [ 0.297424] l4: supplied by s3
  162. [ 0.297431] RPC: Registered tcp transport module.
  163. [ 0.297441] RPC: Registered tcp NFSv4.1 backchannel transport module.
  164. [ 0.297456] PCI: CLS 0 bytes, default 128
  165. [ 0.297460] l4: Bringing 0uV into 1225000-1225000uV
  166. [ 0.297748] l5: supplied by s5
  167. [ 0.297937] l6: supplied by regulator-dummy
  168. [ 0.297977] l6: Bringing 0uV into 1200000-1200000uV
  169. [ 0.298038] Unpacking initramfs...
  170. [ 0.298345] l7: supplied by s5
  171. [ 0.298517] l8: supplied by regulator-dummy
  172. [ 0.298555] l8: Bringing 0uV into 1800000-1800000uV
  173. [ 0.298803] l9: supplied by regulator-dummy
  174. [ 0.298841] l9: Bringing 0uV into 1800000-1800000uV
  175. [ 0.299180] l10: supplied by regulator-dummy
  176. [ 0.299233] l10: Bringing 0uV into 1800000-1800000uV
  177. [ 0.299553] l11: supplied by s3
  178. [ 0.299590] l11: Bringing 0uV into 1150000-1150000uV
  179. [ 0.300050] l12: supplied by regulator-dummy
  180. [ 0.300090] l12: Bringing 0uV into 1800000-1800000uV
  181. [ 0.300367] l13: supplied by regulator-dummy
  182. [ 0.300410] l13: Bringing 0uV into 1800000-1800000uV
  183. [ 0.300752] l14: supplied by s5
  184. [ 0.300790] l14: Bringing 0uV into 1800000-1800000uV
  185. [ 0.301086] l15: supplied by s5
  186. [ 0.301127] l15: Bringing 0uV into 1800000-1800000uV
  187. [ 0.301441] l16: supplied by regulator-dummy
  188. [ 0.301481] l16: Bringing 0uV into 2700000-2700000uV
  189. [ 0.301780] l17: supplied by regulator-dummy
  190. [ 0.301822] l17: Bringing 0uV into 2500000-2500000uV
  191. [ 0.302335] l18: supplied by regulator-dummy
  192. [ 0.302381] l18: Bringing 0uV into 2700000-2700000uV
  193. [ 0.302731] l19: supplied by regulator-dummy
  194. [ 0.302769] l19: Bringing 0uV into 3000000-3000000uV
  195. [ 0.303090] l20: supplied by s5
  196. [ 0.303136] l20: Bringing 0uV into 2950000-2950000uV
  197. [ 0.303466] l21: supplied by s5
  198. [ 0.303502] l21: Bringing 0uV into 2950000-2950000uV
  199. [ 0.303837] l22: supplied by regulator-dummy
  200. [ 0.303879] l22: Bringing 0uV into 3300000-3300000uV
  201. [ 0.304189] l23: supplied by regulator-dummy
  202. [ 0.304230] l23: Bringing 0uV into 2800000-2800000uV
  203. [ 0.304543] l24: supplied by regulator-dummy
  204. [ 0.304586] l24: Bringing 0uV into 3075000-3075000uV
  205. [ 0.304915] l25: supplied by s3
  206. [ 0.304954] l25: Bringing 0uV into 1200000-1200000uV
  207. [ 0.305271] l26: supplied by s3
  208. [ 0.305457] l27: supplied by s3
  209. [ 0.305496] l27: Bringing 0uV into 1000000-1000000uV
  210. [ 0.305840] l28: supplied by s3
  211. [ 0.305881] l28: Bringing 0uV into 925000-925000uV
  212. [ 0.306862] l29: supplied by regulator-dummy
  213. [ 0.306937] l29: Bringing 0uV into 2800000-2800000uV
  214. [ 0.307352] l30: supplied by regulator-dummy
  215. [ 0.307394] l30: Bringing 0uV into 1800000-1800000uV
  216. [ 0.307768] l31: supplied by s3
  217. [ 0.308062] l32: supplied by regulator-dummy
  218. [ 0.308114] l32: Bringing 0uV into 1800000-1800000uV
  219. [ 0.308513] lvs1: supplied by regulator-dummy
  220. [ 0.308746] lvs2: supplied by regulator-dummy
  221. [ 0.441643] Freeing initrd memory: 4140K
  222. [ 0.446074] kvm [1]: HYP mode not available
  223. [ 0.457501] audit: initializing netlink subsys (disabled)
  224. [ 0.457727] audit: type=2000 audit(0.447:1): state=initialized audit_enabled=0 res=1
  225. [ 0.458071] workingset: timestamp_bits=44 max_order=20 bucket_order=0
  226. [ 0.463310] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  227. [ 0.465060] NFS: Registering the id_resolver key type
  228. [ 0.465169] Key type id_resolver registered
  229. [ 0.465179] Key type id_legacy registered
  230. [ 0.465194] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
  231. [ 0.465667] Key type cifs.spnego registered
  232. [ 0.465692] Key type cifs.idmap registered
  233. [ 0.465835] 9p: Installing v9fs 9p2000 file system support
  234. [ 0.469583] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
  235. [ 0.469607] io scheduler noop registered
  236. [ 0.469737] io scheduler cfq registered (default)
  237. [ 0.469751] io scheduler mq-deadline registered
  238. [ 0.469761] io scheduler kyber registered
  239. [ 0.475313] qcom-qmp-phy 34000.phy: Registered Qcom-QMP phy
  240. [ 0.475821] qcom-qmp-phy 7410000.phy: Registered Qcom-QMP phy
  241. [ 0.477202] ufs_qcom_phy_qmp_14nm 627000.ufsphy: invalid resource
  242. [ 0.477430] ufs_qcom_phy_qmp_14nm 627000.ufsphy: 627000.ufsphy supply vdda-pll not found, using dummy regulator
  243. [ 0.477520] ufs_qcom_phy_qmp_14nm 627000.ufsphy: 627000.ufsphy supply vdda-phy not found, using dummy regulator
  244. [ 0.481217] qcom-pcie 600000.qcom,pcie: Failed to get supply 'vddpe-3v3': -517
  245. [ 0.482259] qcom-pcie 610000.qcom,pcie: 610000.qcom,pcie supply vddpe-3v3 not found, using dummy regulator
  246. [ 0.483131] OF: PCI: host bridge /soc/agnoc@0/qcom,pcie@00610000 ranges:
  247. [ 0.483170] OF: PCI: IO 0x0e200000..0x0e2fffff -> 0x0e200000
  248. [ 0.483189] OF: PCI: MEM 0x0e300000..0x0fffffff -> 0x0e300000
  249. [ 0.588563] qcom-pcie 610000.qcom,pcie: link up
  250. [ 0.588768] qcom-pcie 610000.qcom,pcie: PCI host bridge to bus 0002:00
  251. [ 0.588787] pci_bus 0002:00: root bus resource [bus 00-ff]
  252. [ 0.588801] pci_bus 0002:00: root bus resource [io 0x0000-0xfffff] (bus address [0xe200000-0xe2fffff])
  253. [ 0.588817] pci_bus 0002:00: root bus resource [mem 0x0e300000-0x0fffffff]
  254. [ 0.588861] pci 0002:00:00.0: [17cb:0104] type 01 class 0x060400
  255. [ 0.588905] pci 0002:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
  256. [ 0.588992] pci 0002:00:00.0: PME# supported from D0 D3hot
  257. [ 0.589542] pci 0002:01:00.0: [1969:1083] type 00 class 0x020000
  258. [ 0.590059] pci 0002:01:00.0: reg 0x10: [mem 0x00000000-0x0003ffff 64bit]
  259. [ 0.590246] pci 0002:01:00.0: reg 0x18: initial BAR value 0x00000000 invalid
  260. [ 0.590265] pci 0002:01:00.0: reg 0x18: [io size 0x0080]
  261. [ 0.591873] pci 0002:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
  262. [ 0.602379] pci 0002:00:00.0: BAR 14: assigned [mem 0x0e300000-0x0e3fffff]
  263. [ 0.602399] pci 0002:00:00.0: BAR 0: assigned [mem 0x0e400000-0x0e400fff 64bit]
  264. [ 0.602425] pci 0002:00:00.0: BAR 13: assigned [io 0x1000-0x1fff]
  265. [ 0.602442] pci 0002:01:00.0: BAR 0: assigned [mem 0x0e300000-0x0e33ffff 64bit]
  266. [ 0.602630] pci 0002:01:00.0: BAR 2: assigned [io 0x1000-0x107f]
  267. [ 0.602695] pci 0002:00:00.0: PCI bridge to [bus 01-ff]
  268. [ 0.602708] pci 0002:00:00.0: bridge window [io 0x1000-0x1fff]
  269. [ 0.602725] pci 0002:00:00.0: bridge window [mem 0x0e300000-0x0e3fffff]
  270. [ 0.603121] pcieport 0002:00:00.0: Signaling PME with IRQ 104
  271. [ 0.603284] pcieport 0002:00:00.0: AER enabled with IRQ 104
  272. [ 0.603412] pci 0002:01:00.0: [Firmware Bug]: disabling VPD access (can't determine size of non-standard VPD format)
  273. [ 0.608866] gpio-clk clocks:divclk1: could not find pctldev for node /soc/qcom,spmi@400f000/pmic@0/gpios@c000/clk_div1, deferring probe
  274. [ 0.638006] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
  275. [ 0.641486] SuperH (H)SCI(F) driver initialized
  276. [ 0.643021] msm_serial 7570000.serial: msm_serial: detected port #2
  277. [ 0.643106] msm_serial 7570000.serial: uartclk = 19200000
  278. [ 0.643209] 7570000.serial: ttyMSM2 at MMIO 0x7570000 (irq = 9, base_baud = 1200000) is a MSM
  279. [ 0.643515] serial serial0: tty port ttyMSM2 registered
  280. [ 0.643861] msm_serial 75b0000.serial: msm_serial: detected port #0
  281. [ 0.643929] msm_serial 75b0000.serial: uartclk = 7372800
  282. [ 0.643998] 75b0000.serial: ttyMSM0 at MMIO 0x75b0000 (irq = 12, base_baud = 460800) is a MSM
  283. [ 0.644050] msm_serial: console setup on port #0
  284. [ 2.126618] console [ttyMSM0] enabled
  285. [ 2.132819] msm_serial: driver initialized
  286. [ 2.135932] arm-smmu da0000.arm,smmu: probing hardware configuration...
  287. [ 2.138851] arm-smmu da0000.arm,smmu: SMMUv2 with:
  288. [ 2.145383] arm-smmu da0000.arm,smmu: stage 1 translation
  289. [ 2.150204] arm-smmu da0000.arm,smmu: address translation ops
  290. [ 2.155671] arm-smmu da0000.arm,smmu: non-coherent table walk
  291. [ 2.161487] arm-smmu da0000.arm,smmu: (IDR0.CTTW overridden by FW configuration)
  292. [ 2.167312] arm-smmu da0000.arm,smmu: stream matching with 4 register groups
  293. [ 2.174902] arm-smmu da0000.arm,smmu: 2 context banks (0 stage-2 only)
  294. [ 2.182004] arm-smmu da0000.arm,smmu: Supported page sizes: 0x63315000
  295. [ 2.188407] arm-smmu da0000.arm,smmu: Stage-1: 32-bit VA -> 36-bit IPA
  296. [ 2.196750] arm-smmu d00000.arm,smmu: probing hardware configuration...
  297. [ 2.201632] arm-smmu d00000.arm,smmu: SMMUv2 with:
  298. [ 2.208224] arm-smmu d00000.arm,smmu: stage 1 translation
  299. [ 2.213060] arm-smmu d00000.arm,smmu: address translation ops
  300. [ 2.218516] arm-smmu d00000.arm,smmu: non-coherent table walk
  301. [ 2.224341] arm-smmu d00000.arm,smmu: (IDR0.CTTW overridden by FW configuration)
  302. [ 2.230156] arm-smmu d00000.arm,smmu: stream matching with 2 register groups
  303. [ 2.237743] arm-smmu d00000.arm,smmu: 2 context banks (0 stage-2 only)
  304. [ 2.244854] arm-smmu d00000.arm,smmu: Supported page sizes: 0x63315000
  305. [ 2.251257] arm-smmu d00000.arm,smmu: Stage-1: 32-bit VA -> 36-bit IPA
  306. [ 2.259087] arm-smmu 1600000.arm,smmu-lpass_q6: probing hardware configuration...
  307. [ 2.264459] arm-smmu 1600000.arm,smmu-lpass_q6: SMMUv2 with:
  308. [ 2.272107] arm-smmu 1600000.arm,smmu-lpass_q6: stage 1 translation
  309. [ 2.277809] arm-smmu 1600000.arm,smmu-lpass_q6: address translation ops
  310. [ 2.284147] arm-smmu 1600000.arm,smmu-lpass_q6: non-coherent table walk
  311. [ 2.290830] arm-smmu 1600000.arm,smmu-lpass_q6: (IDR0.CTTW overridden by FW configuration)
  312. [ 2.297535] arm-smmu 1600000.arm,smmu-lpass_q6: stream matching with 15 register groups
  313. [ 2.305622] arm-smmu 1600000.arm,smmu-lpass_q6: 12 context banks (0 stage-2 only)
  314. [ 2.313954] arm-smmu 1600000.arm,smmu-lpass_q6: Supported page sizes: 0x63315000
  315. [ 2.321299] arm-smmu 1600000.arm,smmu-lpass_q6: Stage-1: 36-bit VA -> 36-bit IPA
  316. [ 2.330934] arm-smmu d40000.arm,smmu-venus: probing hardware configuration...
  317. [ 2.336335] arm-smmu d40000.arm,smmu-venus: SMMUv2 with:
  318. [ 2.343482] arm-smmu d40000.arm,smmu-venus: stage 1 translation
  319. [ 2.348824] arm-smmu d40000.arm,smmu-venus: address translation ops
  320. [ 2.354805] arm-smmu d40000.arm,smmu-venus: non-coherent table walk
  321. [ 2.361147] arm-smmu d40000.arm,smmu-venus: (IDR0.CTTW overridden by FW configuration)
  322. [ 2.367488] arm-smmu d40000.arm,smmu-venus: stream matching with 42 register groups
  323. [ 2.375261] arm-smmu d40000.arm,smmu-venus: 7 context banks (0 stage-2 only)
  324. [ 2.383216] arm-smmu d40000.arm,smmu-venus: Supported page sizes: 0x63315000
  325. [ 2.390226] arm-smmu d40000.arm,smmu-venus: Stage-1: 32-bit VA -> 36-bit IPA
  326. [ 2.406393] iommu: Adding device 901000.mdp to group 0
  327. [ 2.406540] msm_mdp 901000.mdp: Linked as a consumer to d00000.arm,smmu
  328. [ 2.451614] loop: module loaded
  329. [ 2.454019] ufshcd-qcom 624000.ufshc: ufshcd_populate_vreg: Unable to find vdd-hba-supply regulator, assuming enabled
  330. [ 2.458216] scsi host0: ufshcd
  331. [ 2.483462] spi_qup 7575000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
  332. [ 2.485090] spmi spmi-0: PMIC arbiter version v2 (0x20010000)
  333. [ 2.498896] ufshcd-qcom 624000.ufshc: ufshcd_print_pwr_info:[RX, TX]: gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate = 0
  334. [ 2.500908] qcom,qpnp-power-on 400f000.qcom,spmi:pmic@2:qcom,power-on@800: No PON config. specified
  335. [ 2.510367] qcom,qpnp-power-on 400f000.qcom,spmi:pmic@2:qcom,power-on@800: PMIC@SID2 Power-on reason: Triggered from Hard Reset and 'warm' boot
  336. [ 2.519248] qcom,qpnp-power-on 400f000.qcom,spmi:pmic@2:qcom,power-on@800: PMIC@SID2: Power-off reason: Triggered from PS_HOLD (PS_HOLD/MSM controlled shutdown)
  337. [ 2.521316] ufshcd-qcom 624000.ufshc: ufshcd_print_pwr_info:[RX, TX]: gear=[3, 3], lane[1, 1], pwr[FAST MODE, FAST MODE], rate = 2
  338. [ 2.537409] s1: supplied by regulator-dummy
  339. [ 2.548501] scsi 0:0:0:49488: Well-known LUN TOSHIBA THGAF4G9N4LBAIRB 0100 PQ: 0 ANSI: 6
  340. [ 2.558837] s2: supplied by regulator-dummy
  341. [ 2.564247] scsi 0:0:0:49456: Well-known LUN TOSHIBA THGAF4G9N4LBAIRB 0100 PQ: 0 ANSI: 6
  342. [ 2.571089] s2: Bringing 1270000uV into 1015000-1015000uV
  343. [ 2.576339] scsi 0:0:0:49476: Well-known LUN TOSHIBA THGAF4G9N4LBAIRB 0100 PQ: 0 ANSI: 6
  344. [ 2.584568] l1: supplied by regulator-dummy
  345. [ 2.590522] scsi 0:0:0:0: Direct-Access TOSHIBA THGAF4G9N4LBAIRB 0100 PQ: 0 ANSI: 6
  346. [ 2.600400] libphy: Fixed MDIO Bus: probed
  347. [ 2.602952] scsi 0:0:0:1: Direct-Access TOSHIBA THGAF4G9N4LBAIRB 0100 PQ: 0 ANSI: 6
  348. [ 2.610268] tun: Universal TUN/TAP device driver, 1.6
  349. [ 2.615664] scsi 0:0:0:2: Direct-Access TOSHIBA THGAF4G9N4LBAIRB 0100 PQ: 0 ANSI: 6
  350. [ 2.623168] atl1c 0002:01:00.0: enabling device (0000 -> 0002)
  351. [ 2.629578] scsi 0:0:0:3: Direct-Access TOSHIBA THGAF4G9N4LBAIRB 0100 PQ: 0 ANSI: 6
  352. [ 2.641519] sd 0:0:0:0: [sda] 14145536 4096-byte logical blocks: (57.9 GB/54.0 GiB)
  353. [ 2.648827] sd 0:0:0:1: [sdb] 1024 4096-byte logical blocks: (4.19 MB/4.00 MiB)
  354. [ 2.656163] sd 0:0:0:1: [sdb] Write Protect is off
  355. [ 2.656175] sd 0:0:0:1: [sdb] Mode Sense: 00 32 00 10
  356. [ 2.657383] sd 0:0:0:1: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
  357. [ 2.664006] scsi 0:0:0:4: Direct-Access TOSHIBA THGAF4G9N4LBAIRB 0100 PQ: 0 ANSI: 6
  358. [ 2.677337] sd 0:0:0:2: [sdc] 1024 4096-byte logical blocks: (4.19 MB/4.00 MiB)
  359. [ 2.678423] scsi 0:0:0:5: Direct-Access TOSHIBA THGAF4G9N4LBAIRB 0100 PQ: 0 ANSI: 6
  360. [ 2.685427] sd 0:0:0:0: [sda] Write Protect is off
  361. [ 2.692058] random: fast init done
  362. [ 2.701246] atl1c 0002:01:00.0: version 1.0.1.1-NAPI
  363. [ 2.707159] sd 0:0:0:5: [sdf] 393216 4096-byte logical blocks: (1.61 GB/1.50 GiB)
  364. [ 2.708456] sd 0:0:0:2: [sdc] Write Protect is off
  365. [ 2.713703] sd 0:0:0:5: [sdf] Write Protect is off
  366. [ 2.721871] usbcore: registered new interface driver rtl8150
  367. [ 2.725962] sd 0:0:0:5: [sdf] Mode Sense: 00 32 00 10
  368. [ 2.727677] sd 0:0:0:3: [sdd] 32768 4096-byte logical blocks: (134 MB/128 MiB)
  369. [ 2.730497] sd 0:0:0:0: [sda] Mode Sense: 00 32 00 10
  370. [ 2.731344] sd 0:0:0:3: [sdd] Write Protect is off
  371. [ 2.731647] sd 0:0:0:3: [sdd] Mode Sense: 00 32 00 10
  372. [ 2.736928] sd 0:0:0:5: [sdf] Write cache: enabled, read cache: enabled, supports DPO and FUA
  373. [ 2.743453] usbcore: registered new interface driver r8152
  374. [ 2.743516] usbcore: registered new interface driver asix
  375. [ 2.743576] usbcore: registered new interface driver ax88179_178a
  376. [ 2.743935] VFIO - User Level meta-driver version: 0.3
  377. [ 2.744312] sd 0:0:0:3: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
  378. [ 2.750386] sdb: sdb1
  379. [ 2.761048] sd 0:0:0:2: [sdc] Mode Sense: 00 32 00 10
  380. [ 2.763483] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
  381. [ 2.765252] sd 0:0:0:4: [sde] 1048576 4096-byte logical blocks: (4.29 GB/4.00 GiB)
  382. [ 2.765414] sd 0:0:0:4: [sde] Write Protect is off
  383. [ 2.765427] sd 0:0:0:4: [sde] Mode Sense: 00 32 00 10
  384. [ 2.765598] sd 0:0:0:4: [sde] Write cache: enabled, read cache: enabled, supports DPO and FUA
  385. [ 2.769406] sde: sde1 sde2 sde3 sde4 sde5 sde6 sde7 sde8 sde9 sde10 sde11 sde12 sde13 sde14 sde15 sde16 sde17 sde18 sde19 sde20 sde21 sde22 sde23 sde24 sde25 sde26 sde27 sde28 sde29 sde30
  386. [ 2.819400] dwc3 7600000.dwc3: failed to initialize core
  387. [ 2.819828] sd 0:0:0:2: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA
  388. [ 2.824843] sdd: sdd1 sdd2 sdd3
  389. [ 2.825632] sda: sda1 sda2
  390. [ 2.831638] sd 0:0:0:0: [sda] Attached SCSI disk
  391. [ 2.834536] sd 0:0:0:3: [sdd] Attached SCSI disk
  392. [ 2.838423] sdf: sdf1 sdf2 sdf3 sdf4 sdf5 sdf6 sdf7 sdf8 sdf9
  393. [ 2.838688] sd 0:0:0:1: [sdb] Attached SCSI disk
  394. [ 2.845314] sd 0:0:0:4: [sde] Attached SCSI disk
  395. [ 2.852124] dwc3 6a00000.dwc3: failed to initialize core
  396. [ 2.858875] sd 0:0:0:5: [sdf] Attached SCSI disk
  397. [ 2.862654] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  398. [ 2.889573] ehci-pci: EHCI PCI platform driver
  399. [ 2.896021] ehci-platform: EHCI generic platform driver
  400. [ 2.900732] ehci-msm: Qualcomm On-Chip EHCI Host Controller
  401. [ 2.907009] usbcore: registered new interface driver usb-storage
  402. [ 2.911133] usbcore: registered new interface driver usbserial
  403. [ 2.916608] sdc: sdc1
  404. [ 2.917338] usbcore: registered new interface driver usbserial_generic
  405. [ 2.925253] usbserial: USB Serial support registered for generic
  406. [ 2.935092] i2c /dev entries driver
  407. [ 2.939422] i2c_qup 75b5000.i2c: using default clock-frequency 100000
  408. [ 2.941060] i2c_qup 75b5000.i2c:
  409. tx channel not available
  410. [ 2.949105] i2c_qup 75ba000.i2c: using default clock-frequency 100000
  411. [ 2.954477] i2c_qup 75ba000.i2c:
  412. tx channel not available
  413. [ 2.956875] sd 0:0:0:2: [sdc] Attached SCSI disk
  414. [ 2.974608] input: EP0790M09 as /devices/platform/soc/75ba000.i2c/i2c-4/4-0038/input/input0
  415. [ 2.977946] tps6105x 4-0033: TPS6105x found in SHUTDOWN mode
  416. [ 2.982341] tps6105x 4-0033: present, not used for anything, only GPIO
  417. [ 2.988310] i2c_qup 757a000.i2c: using default clock-frequency 100000
  418. [ 2.994087] i2c_qup 757a000.i2c:
  419. tx channel not available
  420. [ 3.007454] input: pm8941_pwrkey as /devices/platform/soc/400f000.qcom,spmi/spmi-0/0-00/400f000.qcom,spmi:pmic@0:pon@800/400f000.qcom,spmi:pmic@0:pon@800:pwrkey/input/input1
  421. [ 3.009164] input: pm8941_pwrkey as /devices/platform/soc/400f000.qcom,spmi/spmi-0/0-00/400f000.qcom,spmi:pmic@0:pon@800/400f000.qcom,spmi:pmic@0:pon@800:resin/input/input2
  422. [ 3.031990] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 614400 KHz
  423. [ 3.038605] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 652800 KHz
  424. [ 3.047347] cpufreq: cpufreq_online: CPU2: Running at unlisted freq: 19200 KHz
  425. [ 3.054179] cpufreq: cpufreq_online: CPU2: Unlisted initial frequency changed to: 307200 KHz
  426. [ 3.062004] sdhci: Secure Digital Host Controller Interface driver
  427. [ 3.069731] sdhci: Copyright(c) Pierre Ossman
  428. [ 3.076012] sdhci-pltfm: SDHCI platform and OF driver helper
  429. [ 3.080935] ledtrig-cpu: registered to indicate activity on CPUs
  430. [ 3.086843] usbcore: registered new interface driver usbhid
  431. [ 3.091860] usbhid: USB HID core driver
  432. [ 3.100420] opt3001 3-0044: Found TI OPT3001
  433. [ 3.106420] usbcore: registered new interface driver snd-usb-audio
  434. [ 3.108094] NET: Registered protocol family 10
  435. [ 3.112534] Segment Routing with IPv6
  436. [ 3.115986] NET: Registered protocol family 17
  437. [ 3.119703] 9pnet: Installing 9P2000 support
  438. [ 3.124048] Key type dns_resolver registered
  439. [ 3.128948] registered taskstats version 1
  440. [ 3.144498] qcom-qusb2-phy 7411000.phy: Registered Qcom-QUSB2 phy
  441. [ 3.144873] qcom-qusb2-phy 7412000.phy: Registered Qcom-QUSB2 phy
  442. [ 3.150032] qcom-pcie 600000.qcom,pcie: Unbalanced pm_runtime_enable!
  443. [ 3.156299] OF: PCI: host bridge /soc/agnoc@0/qcom,pcie@00600000 ranges:
  444. [ 3.162097] OF: PCI: IO 0x0c200000..0x0c2fffff -> 0x0c200000
  445. [ 3.168856] OF: PCI: MEM 0x0c300000..0x0cffffff -> 0x0c300000
  446. [ 3.356230] qcom-pcie 600000.qcom,pcie: link up
  447. [ 3.356672] qcom-pcie 600000.qcom,pcie: PCI host bridge to bus 0000:00
  448. [ 3.359690] pci_bus 0000:00: root bus resource [bus 00-ff]
  449. [ 3.366266] pci_bus 0000:00: root bus resource [io 0x100000-0x1fffff] (bus address [0xc200000-0xc2fffff])
  450. [ 3.371732] pci_bus 0000:00: root bus resource [mem 0x0c300000-0x0cffffff]
  451. [ 3.381416] pci 0000:00:00.0: [17cb:0104] type 01 class 0x060400
  452. [ 3.381488] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
  453. [ 3.381621] pci 0000:00:00.0: PME# supported from D0 D3hot
  454. [ 3.382690] pci 0000:01:00.0: [168c:003e] type 00 class 0x028000
  455. [ 3.383155] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
  456. [ 3.384782] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
  457. [ 3.394556] pci 0000:00:00.0: BAR 14: assigned [mem 0x0c400000-0x0c5fffff]
  458. [ 3.394646] pci 0000:00:00.0: BAR 0: assigned [mem 0x0c300000-0x0c300fff 64bit]
  459. [ 3.400460] pci 0000:01:00.0: BAR 0: assigned [mem 0x0c400000-0x0c5fffff 64bit]
  460. [ 3.407784] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
  461. [ 3.414899] pci 0000:00:00.0: bridge window [mem 0x0c400000-0x0c5fffff]
  462. [ 3.421032] pcieport 0000:00:00.0: Signaling PME with IRQ 184
  463. [ 3.427421] pcieport 0000:00:00.0: AER enabled with IRQ 184
  464. [ 3.436163] arm-smmu b40000.arm,smmu: probing hardware configuration...
  465. [ 3.438187] arm-smmu b40000.arm,smmu: SMMUv2 with:
  466. [ 3.444799] arm-smmu b40000.arm,smmu: stage 1 translation
  467. [ 3.449629] arm-smmu b40000.arm,smmu: address translation ops
  468. [ 3.455082] arm-smmu b40000.arm,smmu: non-coherent table walk
  469. [ 3.460909] arm-smmu b40000.arm,smmu: (IDR0.CTTW overridden by FW configuration)
  470. [ 3.466728] arm-smmu b40000.arm,smmu: stream matching with 2 register groups
  471. [ 3.474331] arm-smmu b40000.arm,smmu: 2 context banks (0 stage-2 only)
  472. [ 3.481428] arm-smmu b40000.arm,smmu: Supported page sizes: 0x63315000
  473. [ 3.487835] arm-smmu b40000.arm,smmu: Stage-1: 48-bit VA -> 36-bit IPA
  474. [ 3.496532] iommu: Adding device b00000.gpu to group 1
  475. [ 3.501175] adreno b00000.gpu: Linked as a consumer to b40000.arm,smmu
  476. [ 3.509540] msm_mdp 901000.mdp: MDP5 version v1.7
  477. [ 3.512731] msm 900000.mdss: bound 901000.mdp (ops mdp5_ops)
  478. [ 3.517594] msm_dsi 994000.dsi: 994000.dsi supply gdsc not found, using dummy regulator
  479. [ 3.523534] msm_dsi 994000.dsi: Using legacy clk name binding. Use "iface" instead of "iface_clk"
  480. [ 3.531635] msm 900000.mdss: bound 994000.dsi (ops dsi_ops)
  481. [ 3.540048] msm_dsi 996000.dsi: 996000.dsi supply gdsc not found, using dummy regulator
  482. [ 3.545796] msm_dsi 996000.dsi: Using legacy clk name binding. Use "iface" instead of "iface_clk"
  483. [ 3.553750] msm 900000.mdss: bound 996000.dsi (ops dsi_ops)
  484. [ 3.563694] msm 900000.mdss: bound 9a0000.hdmi-tx (ops msm_hdmi_ops)
  485. [ 3.568320] adreno b00000.gpu: b00000.gpu supply vdd not found, using dummy regulator
  486. [ 3.574544] adreno b00000.gpu: b00000.gpu supply vddcx not found, using dummy regulator
  487. [ 3.582229] msm 900000.mdss: A530: using IOMMU
  488. [ 3.591130] msm 900000.mdss: bound b00000.gpu (ops a3xx_ops)
  489. [ 3.742533] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
  490. [ 3.742606] [drm] Driver supports precise vblank timestamp query.
  491. [ 3.749863] [drm] Initialized msm 1.3.0 20130625 for 900000.mdss on minor 0
  492. [ 5.135627] Console: switching to colour frame buffer device 60x50
  493. [ 5.149246] msm 900000.mdss: fb0: msm frame buffer device
  494. [ 5.156207] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
  495. [ 5.159774] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 1
  496. [ 5.165484] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x0000000002010010
  497. [ 5.172784] xhci-hcd xhci-hcd.2.auto: irq 147, io mem 0x07600000
  498. [ 5.182726] hub 1-0:1.0: USB hub found
  499. [ 5.188308] hub 1-0:1.0: 1 port detected
  500. [ 5.192022] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
  501. [ 5.195941] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 2
  502. [ 5.201279] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed
  503. [ 5.208847] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
  504. [ 5.219416] hub 2-0:1.0: USB hub found
  505. [ 5.227230] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
  506. [ 5.240113] hctosys: unable to open rtc device (rtc0)
  507. [ 5.244624] ALSA device list:
  508. [ 5.248217] No soundcards found.
  509. [ 5.252532] Freeing unused kernel memory: 704K
  510. [ 5.526186] usb 1-1: new high-speed USB device number 2 using xhci-hcd
  511. [ 5.608207] rtc-pm8xxx 400f000.qcom,spmi:pmic@0:rtc@6000: rtc core: registered pm8xxx_rtc as rtc0
  512. [ 5.689072] hub 1-1:1.0: USB hub found
  513. [ 5.692902] hub 1-1:1.0: 2 ports detected
  514. [ 5.755472] atl1c 0002:01:00.0 enP2p1s0: renamed from eth0
  515. [ 10.883366] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
  516. [ 11.037007] systemd[1]: System time before build time, advancing clock.
  517. [ 11.058257] ip_tables: (C) 2000-2006 Netfilter Core Team
  518. [ 11.083662] random: systemd: uninitialized urandom read (16 bytes read)
  519. [ 11.366397] random: systemd: uninitialized urandom read (16 bytes read)
  520. [ 11.377172] random: systemd: uninitialized urandom read (16 bytes read)
  521. [ 11.518551] EXT4-fs (sda1): re-mounted. Opts: data=ordered
  522. [ 11.919442] systemd-journald[1694]: Received request to flush runtime journal from PID 1
  523. [ 12.203854] qcom_adsp_pil adsp-pil: adsp-pil supply cx not found, using dummy regulator
  524. [ 12.223968] qcom_adsp_pil adsp-pil: adsp-pil supply px not found, using dummy regulator
  525. [ 12.232866] NET: Registered protocol family 42
  526. [ 12.238835] remoteproc remoteproc1: 2080000.remoteproc is available
  527. [ 12.255160] remoteproc remoteproc0: adsp-pil is available
  528. [ 12.264270] remoteproc remoteproc0: powering up adsp-pil
  529. [ 12.272606] remoteproc remoteproc0: Booting fw image adsp.mdt, size 7196
  530. [ 12.448438] remoteproc remoteproc0: remote processor adsp-pil is now up
  531. [ 12.457332] spidev spi0.0: buggy DT: spidev listed directly in DT
  532. [ 12.466733] media: Linux media interface: v0.10
  533. [ 12.468117] qcom,apr remoteproc0:smd-edge.apr_audio_svc.-1.-1: Adding APR dev: aprsvc:q6core:4:3
  534. [ 12.480465] qcom,apr remoteproc0:smd-edge.apr_audio_svc.-1.-1: Adding APR dev: aprsvc:q6afe:4:4
  535. [ 12.490316] qcom,apr remoteproc0:smd-edge.apr_audio_svc.-1.-1: Adding APR dev: aprsvc:q6asm:4:7
  536. [ 12.498476] qcom,apr remoteproc0:smd-edge.apr_audio_svc.-1.-1: Adding APR dev: aprsvc:q6adm:4:8
  537. [ 12.517519] iommu: Adding device adsp-pil:smd-edge:fastrpc:cb@8 to group 2
  538. [ 12.525799] Bluetooth: Core ver 2.22
  539. [ 12.532267] ------------[ cut here ]------------
  540. [ 12.536220] WARNING: CPU: 2 PID: 1765 at drivers/spi/spidev.c:730 spidev_probe+0x1f4/0x278 [spidev]
  541. [ 12.538249] qcom,fastrpc-cb adsp-pil:smd-edge:fastrpc:cb@8: Linked as a consumer to 1600000.arm,smmu-lpass_q6
  542. [ 12.549045] Modules linked in: joydev bluetooth(+) ecdh_generic media spidev(+) i2c_qcom_cci slim_qcom_ngd_ctrl leds_qcom_lpg qrtr qcom_q6v5_pil qcom_adsp_pil qcom_common qcom_glink_smem qcom_sysmon remoteproc qmi_helpers rmtfs_mem ip_tables x_tables rtc_pm8xxx
  543. [ 12.549081] CPU: 2 PID: 1765 Comm: systemd-udevd Not tainted 4.14.0-qcomlt-arm64 #7
  544. [ 12.549082] Hardware name: 820 Nano SoM Commando Board (DT)
  545. [ 12.549085] task: ffff8000f8ee4600 task.stack: ffff00000dee0000
  546. [ 12.549097] PC is at spidev_probe+0x1f4/0x278 [spidev]
  547. [ 12.567707] iommu: Adding device adsp-pil:smd-edge:fastrpc:cb@9 to group 3
  548. [ 12.575275] udc-core: couldn't find an available UDC - added [g_mass_storage] to list of pending drivers
  549. [ 12.582096] LR is at spidev_probe+0x1f0/0x278 [spidev]
  550. [ 12.582098] pc : [<ffff000000b2a38c>] lr : [<ffff000000b2a388>] pstate: 40000145
  551. [ 12.582100] sp : ffff00000dee3a80
  552. [ 12.582102] x29: ffff00000dee3a80 x28: ffff8000f79fcdd0
  553. [ 12.582107] x27: 00000000014000c0 x26: 0000000000000124
  554. [ 12.582111] x25: ffff8000f87dc048 x24: 000000000000001f
  555. [ 12.582115] x23: 0000000000000000 x22: 0000000000000000
  556. [ 12.582118] x21: 0000000000000000 x20: ffff8000f7f18800
  557. [ 12.582122] x19: ffff000000b2c1d8 x18: 0000000000000001
  558. [ 12.582126] x17: 0000ffffab58f510 x16: ffff0000082209d8
  559. [ 12.582130] x15: 0000000000000040 x14: 0000000000000000
  560. [ 12.582133] x13: 0000000000000000 x12: 0000000000000030
  561. [ 12.582137] x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f
  562. [ 12.582141] x9 : 02fefeff01fefeff x8 : 7f7f7f7f7f7f7f7f
  563. [ 12.593106] qcom,fastrpc-cb adsp-pil:smd-edge:fastrpc:cb@9: Linked as a consumer to 1600000.arm,smmu-lpass_q6
  564. [ 12.600708] x7 : feff756463686f72 x6 : 0000000000008080
  565. [ 12.600713] x5 : 8080000000000000 x4 : 0000000000000000
  566. [ 12.600717] x3 : ffff000000b2c4f8 x2 : 000000000000dba2
  567. [ 12.600720] x1 : ffff8000f8ee4600 x0 : 0000000000000000
  568. [ 12.600725] Call trace:
  569. [ 12.600728] Exception stack(0xffff00000dee3940 to 0xffff00000dee3a80)
  570. [ 12.600731] 3940: 0000000000000000 ffff8000f8ee4600 000000000000dba2 ffff000000b2c4f8
  571. [ 12.600734] 3960: 0000000000000000 8080000000000000 0000000000008080 feff756463686f72
  572. [ 12.600739] 3980: 7f7f7f7f7f7f7f7f 02fefeff01fefeff 7f7f7f7f7f7f7f7f 0101010101010101
  573. [ 12.610411] iommu: Adding device adsp-pil:smd-edge:fastrpc:cb@10 to group 4
  574. [ 12.612932] 39a0: 0000000000000030 0000000000000000 0000000000000000 0000000000000040
  575. [ 12.622220] qcom,fastrpc-cb adsp-pil:smd-edge:fastrpc:cb@10: Linked as a consumer to 1600000.arm,smmu-lpass_q6
  576. [ 12.629922] 39c0: ffff0000082209d8 0000ffffab58f510 0000000000000001 ffff000000b2c1d8
  577. [ 12.629925] 39e0: ffff8000f7f18800 0000000000000000 0000000000000000 0000000000000000
  578. [ 12.629927] 3a00: 000000000000001f ffff8000f87dc048 0000000000000124 00000000014000c0
  579. [ 12.629929] 3a20: ffff8000f79fcdd0 ffff00000dee3a80 ffff000000b2a388 ffff00000dee3a80
  580. [ 12.629931] 3a40: ffff000000b2a38c 0000000040000145 ffff000000b2c1d8 ffff8000f7f18800
  581. [ 12.629933] 3a60: 0000ffffffffffff 0000000000000000 ffff00000dee3a80 ffff000000b2a38c
  582. [ 12.629947] [<ffff000000b2a38c>] spidev_probe+0x1f4/0x278 [spidev]
  583. [ 12.629958] [<ffff0000086e8310>] spi_drv_probe+0x78/0xc8
  584. [ 12.629964] [<ffff00000863595c>] driver_probe_device+0x2dc/0x430
  585. [ 12.629976] [<ffff000008635b7c>] __driver_attach+0xcc/0x118
  586. [ 12.641440] iommu: Adding device adsp-pil:smd-edge:fastrpc:cb@11 to group 5
  587. [ 12.643432] [<ffff0000086336fc>] bus_for_each_dev+0x4c/0x98
  588. [ 12.643434] [<ffff000008635120>] driver_attach+0x20/0x28
  589. [ 12.643437] [<ffff000008634b48>] bus_add_driver+0x1f0/0x288
  590. [ 12.643439] [<ffff0000086365c8>] driver_register+0x60/0xf8
  591. [ 12.643442] [<ffff0000086e8248>] __spi_register_driver+0x58/0x60
  592. [ 12.643447] [<ffff000000b30088>] spidev_init+0x88/0x1000 [spidev]
  593. [ 12.643453] [<ffff000008083cb8>] do_one_initcall+0x38/0x120
  594. [ 12.643459] [<ffff00000815e058>] do_init_module+0x58/0x1b0
  595. [ 12.643462] [<ffff00000815ce40>] load_module+0x1e38/0x23a8
  596. [ 12.643464] [<ffff00000815d698>] SyS_finit_module+0xd0/0xe8
  597. [ 12.643466] Exception stack(0xffff00000dee3ec0 to 0xffff00000dee4000)
  598. [ 12.643469] 3ec0: 0000000000000006 0000ffffab4b4f50 0000000000000000 0000000000000006
  599. [ 12.643479] 3ee0: 0000000000000000 0000000000000218 0000000000000007 0000000000000007
  600. [ 12.648054] qcom,fastrpc-cb adsp-pil:smd-edge:fastrpc:cb@11: Linked as a consumer to 1600000.arm,smmu-lpass_q6
  601. [ 12.651876] 3f00: 0000000000000111 00000000f7ffdd04 0000000000000002 0000000000000000
  602. [ 12.651879] 3f20: 0000000000000060 0000aaab193b5020 0000000000000000 0000000000000040
  603. [ 12.651881] 3f40: 0000ffffab4cae00 0000ffffab598ee0 0000000000000002 0000aaab193f3a20
  604. [ 12.651883] 3f60: 0000ffffab4b4f50 0000000000000000 0000000000020000 0000aaab193c8020
  605. [ 12.651886] 3f80: 0000aaab193f32d0 0000aaaae5455000 0000aaaae5456000 0000000000020000
  606. [ 12.651888] 3fa0: 0000aaab193f3a20 0000ffffc4e8e840 0000ffffab4ad750 0000ffffc4e8e840
  607. [ 12.651890] 3fc0: 0000ffffab598f04 0000000040000000 0000000000000006 0000000000000111
  608. [ 12.651892] 3fe0: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
  609. [ 12.651895] [<ffff000008083b18>] __sys_trace_return+0x0/0x4
  610. [ 12.651897] ---[ end trace e9c7b803861909f7 ]---
  611. [ 12.663688] Linux video capture interface: v2.00
  612. [ 12.667933] NET: Registered protocol family 31
  613. [ 12.674315] iommu: Adding device adsp-pil:smd-edge:fastrpc:cb@12 to group 6
  614. [ 12.707485] iommu: Adding device a34000.camss to group 7
  615. [ 12.718617] qcom,fastrpc-cb adsp-pil:smd-edge:fastrpc:cb@12: Linked as a consumer to 1600000.arm,smmu-lpass_q6
  616. [ 12.726218] Bluetooth: HCI device and connection manager initialized
  617. [ 12.729231] qcom-camss a34000.camss: Linked as a consumer to da0000.arm,smmu
  618. [ 12.742283] Bluetooth: HCI socket layer initialized
  619. [ 12.747251] iommu: Adding device adsp-pil:smd-edge:fastrpc:cb@5 to group 8
  620. [ 12.763329] Bluetooth: L2CAP socket layer initialized
  621. [ 12.775056] qcom,fastrpc-cb adsp-pil:smd-edge:fastrpc:cb@5: Linked as a consumer to 1600000.arm,smmu-lpass_q6
  622. [ 12.798012] Bluetooth: SCO socket layer initialized
  623. [ 12.807596] iommu: Adding device adsp-pil:smd-edge:fastrpc:cb@6 to group 9
  624. [ 12.822392] Bluetooth: HCI UART driver ver 2.3
  625. [ 12.826328] qcom,fastrpc-cb adsp-pil:smd-edge:fastrpc:cb@6: Linked as a consumer to 1600000.arm,smmu-lpass_q6
  626. [ 12.831720] Bluetooth: HCI UART protocol H4 registered
  627. [ 12.840021] iommu: Adding device adsp-pil:smd-edge:fastrpc:cb@7 to group 10
  628. [ 12.846985] Bluetooth: HCI UART protocol BCSP registered
  629. [ 12.858321] qcom,fastrpc-cb adsp-pil:smd-edge:fastrpc:cb@7: Linked as a consumer to 1600000.arm,smmu-lpass_q6
  630. [ 12.863158] Bluetooth: HCI UART protocol LL registered
  631. [ 13.193964] msm-snd-apq8096 sound: error getting cpu dai name
  632. [ 13.204571] Bluetooth: HCI UART protocol Three-wire (H5) registered
  633. [ 13.209744] msm-snd-apq8096 sound: Error parsing OF data
  634. [ 13.221612] Bluetooth: HCI UART protocol QCA registered
  635. [ 13.226101] Bluetooth: hci0: ROME setup
  636. [ 13.228017] msm-snd-apq8096 sound: error getting cpu dai name
  637. [ 13.236392] Bluetooth: hci0: Set UART speed to 3000000
  638. [ 13.252397] msm-snd-apq8096 sound: Error parsing OF data
  639. [ 13.277518] Error: Driver 'pwm-backlight' is already registered, aborting...
  640. [ 13.337995] iommu: Adding device c00000.video-codec to group 11
  641. [ 13.415013] qcom-venus c00000.video-codec: Linked as a consumer to d40000.arm,smmu-venus
  642. [ 13.533202] random: crng init done
  643. [ 13.538823] random: 7 urandom warning(s) missed due to ratelimiting
  644. [ 13.574966] Bluetooth: hci0: ROME controller version 0x00440302
  645. [ 13.582709] Bluetooth: hci0: ROME Downloading qca/rampatch_00440302.bin
  646. [ 13.590786] bluetooth hci0: Direct firmware load for qca/rampatch_00440302.bin failed with error -2
  647. [ 13.590793] Bluetooth: hci0: Failed to request file: qca/rampatch_00440302.bin (-2)
  648. [ 13.590796] Bluetooth: hci0: Failed to download patch (-2)
  649. [ 13.633148] ath10k_pci 0000:01:00.0: enabling device (0000 -> 0002)
  650. [ 13.647716] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
  651. [ 13.718814] msm-snd-apq8096 sound: error getting cpu dai name
  652. [ 13.726922] msm-snd-apq8096 sound: Error parsing OF data
  653. [ 13.779578] msm-snd-apq8096 sound: error getting cpu dai name
  654. [ 13.779582] msm-snd-apq8096 sound: Error parsing OF data
  655. [ 13.785796] msm-snd-apq8096 sound: error getting cpu dai name
  656. [ 13.785800] msm-snd-apq8096 sound: Error parsing OF data
  657. [ 13.788268] msm-snd-apq8096 sound: error getting cpu dai name
  658. [ 13.788272] msm-snd-apq8096 sound: Error parsing OF data
  659. [ 13.791618] msm-snd-apq8096 sound: error getting cpu dai name
  660. [ 13.791622] msm-snd-apq8096 sound: Error parsing OF data
  661. [ 13.815838] qcom-camss a34000.camss: VFE HW Version = 0x70020000
  662. [ 13.816556] qcom-camss a34000.camss: VFE HW Version = 0x70020000
  663. [ 13.817319] qcom-camss a34000.camss: VFE HW Version = 0x70020000
  664. [ 13.831900] ov5645 6-003b: cannot get enable gpio
  665. [ 13.832074] ov5645: probe of 6-003b failed with error -2
  666. [ 13.834190] qcom-camss a34000.camss: VFE HW Version = 0x70020000
  667. [ 13.837250] qcom-camss a34000.camss: VFE HW Version = 0x70020000
  668. [ 13.856118] qcom-camss a34000.camss: VFE HW Version = 0x70020000
  669. [ 13.856759] qcom-camss a34000.camss: VFE HW Version = 0x70020000
  670. [ 13.872311] msm-snd-apq8096 sound: error getting cpu dai name
  671. [ 13.872315] msm-snd-apq8096 sound: Error parsing OF data
  672. [ 13.876142] msm-snd-apq8096 sound: error getting cpu dai name
  673. [ 13.876146] msm-snd-apq8096 sound: Error parsing OF data
  674. [ 13.876418] qcom-camss a34000.camss: VFE HW Version = 0x70020000
  675. [ 13.882843] qcom,slim-ngd-ctrl 91c0000.slim: SLIM SAT: Rcvd master capability
  676. [ 13.945512] msm-snd-apq8096 sound: error getting cpu dai name
  677. [ 13.956684] iommu: Adding device adsp-pil:smd-edge:apr:q6asm:dais to group 12
  678. [ 13.962014] msm-snd-apq8096 sound: Error parsing OF data
  679. [ 13.972531] q6asm-dai adsp-pil:smd-edge:apr:q6asm:dais: Linked as a consumer to 1600000.arm,smmu-lpass_q6
  680. [ 13.986151] i2c-qcom-cci a0c000.cci: master 1 queue 0 timeout
  681. [ 14.002806] msm-snd-apq8096 sound: codec dai not found
  682. [ 14.002811] msm-snd-apq8096 sound: Error parsing OF data
  683. [ 14.082034] i2c-qcom-cci a0c000.cci: cci master 1 reset and init done:
  684. [ 14.088380] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
  685. [ 14.100449] i2c-qcom-cci a0c000.cci: Master 1 error 0x20000000
  686. [ 14.103295] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal-pci-0000:01:00.0.bin failed with error -2
  687. [ 14.111036] i2c-qcom-cci a0c000.cci: master 1 queue 0 error -5
  688. [ 14.123907] ath10k_pci 0000:01:00.0: qca6174 hw3.2 target 0x05030000 chip_id 0x00340aff sub 0000:0000
  689. [ 14.128667] i2c-qcom-cci a0c000.cci: cci i2c xfer error -5
  690. [ 14.137160] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
  691. [ 14.145526] ov5645 7-003c: ov5645_write_reg: write reg error -5: reg=3103, val=11
  692. [ 14.154575] ath10k_pci 0000:01:00.0: firmware ver WLAN.RM.4.4.1-00079-QCARMSWPZ-1 api 6 features wowlan,ignore-otp crc32 fd869beb
  693. [ 14.162373] ov5645 7-003c: could not set init registers
  694. [ 14.179760] ov5645 7-003c: could not power up OV5645
  695. [ 14.180045] ov5645: probe of 7-003c failed with error -5
  696. [ 14.245158] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=1 from ath10k/QCA6174/hw3.0/board-2.bin
  697. [ 14.258816] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id 0:1 crc32 ed5f849a
  698. [ 14.560362] sdc: sdc1
  699. [ 14.609181] sdd: sdd1 sdd2 sdd3
  700. [ 14.716150] sde: sde1 sde2 sde3 sde4 sde5 sde6 sde7 sde8 sde9 sde10 sde11 sde12 sde13 sde14 sde15 sde16 sde17 sde18 sde19 sde20 sde21 sde22 sde23 sde24 sde25 sde26 sde27 sde28 sde29 sde30
  701. [ 14.801761] sdf: sdf1 sdf2 sdf3 sdf4 sdf5 sdf6 sdf7 sdf8 sdf9
  702. [ 14.818372] wcd9335-slim 217:1a0:0:0: setting slimbus l-addr:ca, ea:217,1a0,0,0
  703. [ 14.831589] slimbus 217:1a0:1:0: setting slimbus l-addr:cb, ea:217,1a0,1,0
  704. [ 14.841429] msm-snd-apq8096 sound: codec dai not found
  705. [ 14.846027] msm-snd-apq8096 sound: Error parsing OF data
  706. [ 14.892908] ath10k_pci 0000:01:00.0: Unknown eventid: 118809
  707. [ 14.901472] ath10k_pci 0000:01:00.0: Unknown eventid: 90118
  708. [ 14.916656] ath10k_pci 0000:01:00.0: htt-ver 3.47 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
  709. [ 14.930683] wcd9335-slim 217:1a0:1:0: WCD9335 CODEC version is v2.0
  710. [ 15.010215] ath: EEPROM regdomain: 0x0
  711. [ 15.010222] ath: EEPROM indicates default country code should be used
  712. [ 15.010225] ath: doing EEPROM country->regdmn map search
  713. [ 15.010229] ath: country maps to regdmn code: 0x3a
  714. [ 15.010231] ath: Country alpha2 being used: US
  715. [ 15.010234] ath: Regpair used: 0x3a
  716. [ 15.086024] msm-snd-apq8096 sound: codec dai not found
  717. [ 15.090996] msm-snd-apq8096 sound: Error parsing OF data
  718. [ 15.326391] ath10k_pci 0000:01:00.0 wlp1s0: renamed from wlan0
  719. [ 15.708681] sdb: sdb1
  720. [ 15.854344] sdb: sdb1
  721. [ 15.875109] sdc: sdc1
  722. [ 15.884622] sdc: sdc1
  723. [ 16.043850] sdc: sdc1
  724. [ 16.077061] sdd: sdd1 sdd2 sdd3
  725. [ 16.104196] sdd: sdd1 sdd2 sdd3
  726. [ 16.243222] sdd: sdd1 sdd2 sdd3
  727. [ 16.272505] sde: sde1 sde2 sde3 sde4 sde5 sde6 sde7 sde8 sde9 sde10 sde11 sde12 sde13 sde14 sde15 sde16 sde17 sde18 sde19 sde20 sde21 sde22 sde23 sde24 sde25 sde26 sde27 sde28 sde29 sde30
  728. [ 16.734578] sde: sde1 sde2 sde3 sde4 sde5 sde6 sde7 sde8 sde9 sde10 sde11 sde12 sde13 sde14 sde15 sde16 sde17 sde18 sde19 sde20 sde21 sde22 sde23 sde24 sde25 sde26 sde27 sde28 sde29 sde30
  729. [ 16.793785] sdf: sdf1 sdf2 sdf3 sdf4 sdf5 sdf6 sdf7 sdf8 sdf9
  730. [ 16.824250] sdf: sdf1 sdf2 sdf3 sdf4 sdf5 sdf6 sdf7 sdf8 sdf9
  731. [ 17.260004] sdf: sdf1 sdf2 sdf3 sdf4 sdf5 sdf6 sdf7 sdf8 sdf9
  732. [ 17.327382] sdc: sdc1
  733. [ 17.344525] sdd: sdd1 sdd2 sdd3
  734. [ 17.388851] sde: sde1 sde2 sde3 sde4 sde5 sde6 sde7 sde8 sde9 sde10 sde11 sde12 sde13 sde14 sde15 sde16 sde17 sde18 sde19 sde20 sde21 sde22 sde23 sde24 sde25 sde26 sde27 sde28 sde29 sde30
  735. [ 18.048331] sdb: sdb1
  736. [ 18.213084] sdb: sdb1
  737. [ 18.236059] sdc: sdc1
  738. [ 18.251214] sdc: sdc1
  739. [ 18.405450] sdc: sdc1
  740. [ 18.445109] sdd: sdd1 sdd2 sdd3
  741. [ 18.578849] sdd: sdd1 sdd2 sdd3
  742. [ 19.292001] sde: sde1 sde2 sde3 sde4 sde5 sde6 sde7 sde8 sde9 sde10 sde11 sde12 sde13 sde14 sde15 sde16 sde17 sde18 sde19 sde20 sde21 sde22 sde23 sde24 sde25 sde26 sde27 sde28 sde29 sde30
  743. [ 19.378832] sdf: sdf1 sdf2 sdf3 sdf4 sdf5 sdf6 sdf7 sdf8 sdf9
  744. [ 19.409578] sdf: sdf1 sdf2 sdf3 sdf4 sdf5 sdf6 sdf7 sdf8 sdf9
  745. [ 19.416523] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  746. [ 19.421986] Bluetooth: BNEP filters: protocol multicast
  747. [ 19.428336] Bluetooth: BNEP socket layer initialized
  748. [ 20.080625] sdf: sdf1 sdf2 sdf3 sdf4 sdf5 sdf6 sdf7 sdf8 sdf9
  749. [ 20.086646] EXT4-fs (sda1): resizing filesystem from 1042432 to 10747904 blocks
  750. [ 20.259241] EXT4-fs (sda1): resized filesystem to 10747904
  751. [ 21.417395] IPv6: ADDRCONF(NETDEV_UP): enP2p1s0: link is not ready
  752. [ 21.455585] IPv6: ADDRCONF(NETDEV_UP): enP2p1s0: link is not ready
  753. [ 21.495514] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
  754. [ 21.855848] msm 900000.mdss: loaded qcom/a530_pm4.fw from legacy location
  755. [ 21.862735] msm 900000.mdss: loaded qcom/a530_pfp.fw from legacy location
  756. [ 21.869888] msm 900000.mdss: loaded qcom/a530v3_gpmu.fw2 from legacy location
  757. [ 21.877310] msm 900000.mdss: loaded qcom/a530_zap.mdt from legacy location
  758. [ 22.243657] ath10k_pci 0000:01:00.0: Unknown eventid: 118809
  759. [ 22.246626] ath10k_pci 0000:01:00.0: Unknown eventid: 90118
  760. [ 22.272795] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
  761. [ 23.107037] ath10k_pci 0000:01:00.0: Unknown eventid: 118809
  762. [ 23.109985] ath10k_pci 0000:01:00.0: Unknown eventid: 90118
  763. [ 23.136910] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
  764. [ 23.273142] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
  765. [ 25.194015] atl1c 0002:01:00.0: atl1c: enP2p1s0 NIC Link is Up<100 Mbps Full Duplex>
  766. [ 25.194225] IPv6: ADDRCONF(NETDEV_CHANGE): enP2p1s0: link becomes ready
Add Comment
Please, Sign In to add comment