Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;CHK:AA;SD:0;READ:0;0.0;CHK:0;
- no sdio debug board detected
- TE: 156701
- BL2 Built : 13:48:56, Sep 23 2016.
- gxl g7459bd4 - jianxin.pan@droid06
- set vcck to 1120 mv
- set vddee to 1000 mv
- Board ID = 6
- CPU clk: 1200MHz
- DQS-corr enabled
- DDR scramble enabled
- DDR3 chl: Rank0+1 @ 792MHz - PASS
- Rank0: 1024MB(auto)-2T-11
- Rank1: 1024MB(auto)-2T-11
- DataBus test pass!
- AddrBus test pass!
- Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
- New fip structure!
- Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600
- Load bl31 from SD, src: 0x00020200, des: 0x10100000, size: 0x00015400
- Load bl33 from SD, src: 0x00038200, des: 0x01000000, size: 0x000a3400
- NOTICE: BL3-1: v1.0(debug):2e39a99
- NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
- aml log : bl31 normal boot !
- [Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
- OPS=0x82
- 5f c4 f5 66 bb 56 6c 27 b3 38 98 bd [0.535769 Inits done]
- secure task start!
- high task start!
- low task start!
- INFO: BL3-1: Initializing runtime services
- WARNING: No OPTEE provided by BL2 boot loader
- ERROR: Error initializing runtime service opteed_fast
- INFO: BL3-1: Preparing for EL3 exit to normal world
- INFO: BL3-1: Next image address = 0x1000000
- INFO: BL3-1: Next image spsr = 0x3c9
- U-Boot 2015.01-gb2d1c89-dirty (Dec 25 2016 - 19:39:32)
- DRAM: 2 GiB
- Relocation Offset is: 76ed1000
- register usb cfg[0][1] = 0000000077f62c60
- vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
- vpu: clk_level = 7
- vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
- boot_device_flag : 1
- Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
- init bus_cycle=6, bus_timing=7, system=5.0ns
- reset failed
- get_chip_type and ret:fffffffe
- get_chip_type and ret:fffffffe
- chip detect failed and ret:fffffffe
- nandphy_init failed and ret=0xfffffff1
- MMC: aml_priv->desc_buf = 0x0000000073ed16b0
- aml_priv->desc_buf = 0x0000000073ed39d0
- SDIO Port B: 0, SDIO Port C: 1
- emmc/sd response timeout, cmd8, status=0x1ff2800
- emmc/sd response timeout, cmd55, status=0x1ff2800
- [mmc_startup] mmc refix success
- [mmc_init] mmc init success
- mmc read lba=0x14000, blocks=0x400
- start dts,buffer=0000000073ed6270,dt_addr=0000000073ed6270
- parts: 11
- 00: logo 0000000002000000 1
- 01: recovery 0000000002000000 1
- 02: rsv 0000000000800000 1
- 03: tee 0000000000800000 1
- 04: crypt 0000000002000000 1
- 05: misc 0000000002000000 1
- 06: instaboot 0000000020000000 1
- 07: boot 0000000002000000 1
- 08: system 0000000040000000 1
- 09: cache 0000000020000000 2
- 10: data ffffffffffffffff 4
- get_dtb_struct: Get emmc dtb OK!
- overide_emmc_partition_table: overide cache
- [mmc_get_partition_table] skip partition cache.
- Partition table get from SPL is :
- name offset size flag
- ===================================================================================
- 0: bootloader 0 400000 0
- 1: reserved 2400000 4000000 0
- 2: cache 6c00000 20000000 2
- 3: env 27400000 800000 0
- 4: logo 28400000 2000000 1
- 5: recovery 2ac00000 2000000 1
- 6: rsv 2d400000 800000 1
- 7: tee 2e400000 800000 1
- 8: crypt 2f400000 2000000 1
- 9: misc 31c00000 2000000 1
- 10: instaboot 34400000 20000000 1
- 11: boot 54c00000 2000000 1
- 12: system 57400000 40000000 1
- 13: data 97c00000 13a400000 4
- mmc read lba=0x12000, blocks=0x2
- mmc read lba=0x12002, blocks=0x2
- mmc_read_partition_tbl: mmc read partition OK!
- eMMC/TSD partition table have been checked OK!
- mmc env offset: 0x27400000
- In: serial
- Out: serial
- Err: serial
- reboot_mode=watchdog_reboot
- hpd_state=0
- [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
- read emmc dtb
- card in
- [mmc_init] mmc init success
- Device: SDIO Port B
- Manufacturer ID: 0
- OEM: 2020
- Name: N/A
- Tran Speed: 50000000
- Rd Block Len: 512
- SD version 2.0
- High Capacity: Yes
- Capacity: 3.8 GiB
- mmc clock: 40000000
- Bus Width: 4-bit
- Net: dwmac.c9410000
- wipe_data=successful
- wipe_cache=successful
- upgrade_step=0
- "Synchronous Abort" handler, esr 0x96000210
- ELR: 77f3e50c
- LR: 77f0bbfc
- x0 : 0000000000000000 x1 : 0000000077f597ac
- x2 : 0000000000000004 x3 : 0000000000000000
- x4 : 0000000000000000 x5 : 0000000000000000
- x6 : 0000000000000000 x7 : 0000000077f64da0
- x8 : 0000000000000001 x9 : 0000000000000000
- x10: 000000000000000f x11: 0000000073ec0ac8
- x12: 0000000077f46000 x13: 0000000000000000
- x14: 0000000000000000 x15: 0000000000000000
- x16: 0000000000000000 x17: 0000000000000000
- x18: 0000000073ec0e28 x19: 0000000000000001
- x20: 0000000000000000 x21: 0000000077f48d30
- x22: 0000000000000000 x23: 0000000077f48000
- x24: 0000000000000000 x25: 0000000000000000
- x26: 0000000000000000 x27: 0000000073ed64e0
- x28: 0000000000000000 x29: 0000000073ec07f0
- Resetting CPU ...
- resetting ...
- GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;CHK:AA;SD:0;READ:0;0.0;CHK:0;
- no sdio debug board detected
- TE: 156076
- BL2 Built : 13:48:56, Sep 23 2016.
- gxl g7459bd4 - jianxin.pan@droid06
- set vcck to 1120 mv
- set vddee to 1000 mv
- Board ID = 6
- CPU clk: 1200MHz
- DQS-corr enabled
- DDR scramble enabled
- DDR3 chl: Rank0+1 @ 792MHz - PASS
- Rank0: 1024MB(auto)-2T-11
- Rank1: 1024MB(auto)-2T-11
- DataBus test pass!
- AddrBus test pass!
- Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
- New fip structure!
- Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600
- Load bl31 from SD, src: 0x00020200, des: 0x10100000, size: 0x00015400
- Load bl33 from SD, src: 0x00038200, des: 0x01000000, size: 0x000a3400
- NOTICE: BL3-1: v1.0(debug):2e39a99
- NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
- aml log : bl31 normal boot !
- [Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
- OPS=0x82
- 5f c4 f5 66 bb 56 6c 27 b3 38 98 bd [0.535140 Inits done]
- secure task start!
- high task start!
- low task start!
- INFO: BL3-1: Initializing runtime services
- WARNING: No OPTEE provided by BL2 boot loader
- ERROR: Error initializing runtime service opteed_fast
- INFO: BL3-1: Preparing for EL3 exit to normal world
- INFO: BL3-1: Next image address = 0x1000000
- INFO: BL3-1: Next image spsr = 0x3c9
- U-Boot 2015.01-gb2d1c89-dirty (Dec 25 2016 - 19:39:32)
- DRAM: 2 GiB
- Relocation Offset is: 76ed1000
- register usb cfg[0][1] = 0000000077f62c60
- vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
- vpu: clk_level = 7
- vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
- boot_device_flag : 1
- Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
- init bus_cycle=6, bus_timing=7, system=5.0ns
- reset failed
- get_chip_type and ret:fffffffe
- get_chip_type and ret:fffffffe
- chip detect failed and ret:fffffffe
- nandphy_init failed and ret=0xfffffff1
- MMC: aml_priv->desc_buf = 0x0000000073ed16b0
- aml_priv->desc_buf = 0x0000000073ed39d0
- SDIO Port B: 0, SDIO Port C: 1
- emmc/sd response timeout, cmd8, status=0x1ff2800
- emmc/sd response timeout, cmd55, status=0x1ff2800
- [mmc_startup] mmc refix success
- [mmc_init] mmc init success
- mmc read lba=0x14000, blocks=0x400
- start dts,buffer=0000000073ed6270,dt_addr=0000000073ed6270
- parts: 11
- 00: logo 0000000002000000 1
- 01: recovery 0000000002000000 1
- 02: rsv 0000000000800000 1
- 03: tee 0000000000800000 1
- 04: crypt 0000000002000000 1
- 05: misc 0000000002000000 1
- 06: instaboot 0000000020000000 1
- 07: boot 0000000002000000 1
- 08: system 0000000040000000 1
- 09: cache 0000000020000000 2
- 10: data ffffffffffffffff 4
- get_dtb_struct: Get emmc dtb OK!
- overide_emmc_partition_table: overide cache
- [mmc_get_partition_table] skip partition cache.
- Partition table get from SPL is :
- name offset size flag
- ===================================================================================
- 0: bootloader 0 400000 0
- 1: reserved 2400000 4000000 0
- 2: cache 6c00000 20000000 2
- 3: env 27400000 800000 0
- 4: logo 28400000 2000000 1
- 5: recovery 2ac00000 2000000 1
- 6: rsv 2d400000 800000 1
- 7: tee 2e400000 800000 1
- 8: crypt 2f400000 2000000 1
- 9: misc 31c00000 2000000 1
- 10: instaboot 34400000 20000000 1
- 11: boot 54c00000 2000000 1
- 12: system 57400000 40000000 1
- 13: data 97c00000 13a400000 4
- mmc read lba=0x12000, blocks=0x2
- mmc read lba=0x12002, blocks=0x2
- mmc_read_partition_tbl: mmc read partition OK!
- eMMC/TSD partition table have been checked OK!
- mmc env offset: 0x27400000
- In: serial
- Out: serial
- Err: serial
- reboot_mode=watchdog_reboot
- hpd_state=0
- [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
- read emmc dtb
- card in
- [mmc_init] mmc init success
- Device: SDIO Port B
- Manufacturer ID: 0
- OEM: 2020
- Name: N/A
- Tran Speed: 50000000
- Rd Block Len: 512
- SD version 2.0
- High Capacity: Yes
- Capacity: 3.8 GiB
- mmc clock: 40000000
- Bus Width: 4-bit
- Net: dwmac.c9410000
- wipe_data=successful
- wipe_cache=successful
- upgrade_step=0
- "Synchronous Abort" handler, esr 0x96000210
- ELR: 77f3e50c
- LR: 77f0bbfc
- x0 : 0000000000000000 x1 : 0000000077f597ac
- x2 : 0000000000000004 x3 : 0000000000000000
- x4 : 0000000000000000 x5 : 0000000000000000
- x6 : 0000000000000000 x7 : 0000000077f64da0
- x8 : 0000000000000001 x9 : 0000000000000000
- x10: 000000000000000f x11: 0000000073ec0ac8
- x12: 0000000077f46000 x13: 0000000000000000
- x14: 0000000000000000 x15: 0000000000000000
- x16: 0000000000000000 x17: 0000000000000000
- x18: 0000000073ec0e28 x19: 0000000000000001
- x20: 0000000000000000 x21: 0000000077f48d30
- x22: 0000000000000000 x23: 0000000077f48000
- x24: 0000000000000000 x25: 0000000000000000
- x26: 0000000000000000 x27: 0000000073ed64e0
- x28: 0000000000000000 x29: 0000000073ec07f0
- Resetting CPU ...
- resetting ...
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement