SHARE
TWEET

Untitled

a guest Sep 1st, 2019 4 in 269 days
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. # Smoothieboard configuration file, see http://smoothieware.org/configuring-smoothie
  2. # NOTE Lines must not exceed 132 characters, and '#' characters mean what follows is ignored
  3. ## Robot module configurations : general handling of movement G-codes and slicing into moves
  4.  
  5. # Basic motion configuration
  6. default_feed_rate                            1000             # Default speed (mm/minute) for G1/G2/G3 moves
  7. default_seek_rate                            400             # Default speed (mm/minute) for G0 moves
  8. mm_per_arc_segment                           0.0              # Fixed length for line segments that divide arcs, 0 to disable
  9. #mm_per_line_segment                         5                # Cut lines into segments this size
  10. mm_max_arc_error                             0.01             # The maximum error for line segments that divide arcs 0 to disable
  11.                                                               # note it is invalid for both the above be 0
  12.                                                               # if both are used, will use largest segment length based on radius
  13.  
  14. # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
  15. # See http://smoothieware.org/stepper-motors
  16. alpha_steps_per_mm                           806.4516       # Steps per mm for alpha ( X ) stepper
  17. beta_steps_per_mm                            804               # Steps per mm for beta ( Y ) stepper
  18. gamma_steps_per_mm                           801.0050             # Steps per mm for gamma ( Z ) stepper
  19.  
  20. # Planner module configuration : Look-ahead and acceleration configuration
  21. # See http://smoothieware.org/motion-control
  22. acceleration                                 1250             # Acceleration in mm/second/second.
  23. #z_acceleration                              500              # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
  24. junction_deviation                           0.05             # See http://smoothieware.org/motion-control#junction-deviation
  25. #z_junction_deviation                        0.0              # For Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA
  26.  
  27. # Cartesian axis speed limits
  28. x_axis_max_speed                             1250            # Maximum speed in mm/min
  29. y_axis_max_speed                             1250            # Maximum speed in mm/min
  30. z_axis_max_speed                             400              # Maximum speed in mm/min
  31.  
  32. # Stepper module configuration
  33. # Pins are defined as  ports, and pin numbers, appending "!" to the number will invert a pin
  34. # See http://smoothieware.org/pin-configuration and http://smoothieware.org/pinout
  35. alpha_step_pin                               2.0              # Pin for alpha stepper step signal
  36. alpha_dir_pin                                0.5!              # Pin for alpha stepper direction, add '!' to reverse direction
  37. alpha_en_pin                                 0.4              # Pin for alpha enable pin
  38. alpha_current                                1.5              # X stepper motor current
  39. alpha_max_rate                               1250.0          # Maximum rate in mm/min
  40.  
  41. beta_step_pin                                2.1              # Pin for beta stepper step signal
  42. beta_dir_pin                                 0.11             # Pin for beta stepper direction, add '!' to reverse direction
  43. beta_en_pin                                  0.10             # Pin for beta enable
  44. beta_current                                 1.5              # Y stepper motor current
  45. beta_max_rate                                1250.0          # Maxmimum rate in mm/min
  46.  
  47. gamma_step_pin                               2.2              # Pin for gamma stepper step signal
  48. gamma_dir_pin                                0.20             # Pin for gamma stepper direction, add '!' to reverse direction
  49. gamma_en_pin                                 0.19             # Pin for gamma enable
  50. gamma_current                                1.5              # Z stepper motor current
  51. gamma_max_rate                               500.0            # Maximum rate in mm/min
  52.  
  53. ## Extruder module configuration
  54. # See http://smoothieware.org/extruder
  55. extruder.hotend.enable                          false          # Whether to activate the extruder module at all. All configuration is ignored if false
  56. extruder.hotend.steps_per_mm                    140           # Steps per mm for extruder stepper
  57. extruder.hotend.default_feed_rate               600           # Default rate ( mm/minute ) for moves where only the extruder moves
  58. extruder.hotend.acceleration                    500           # Acceleration for the stepper motor mm/sec²
  59. extruder.hotend.max_speed                       50            # Maximum speed in mm/s
  60.  
  61. extruder.hotend.step_pin                        2.3           # Pin for extruder step signal
  62. extruder.hotend.dir_pin                         0.22          # Pin for extruder dir signal ( add '!' to reverse direction )
  63. extruder.hotend.en_pin                          0.21          # Pin for extruder enable signal
  64.  
  65. # Extruder offset
  66. #extruder.hotend.x_offset                        0            # X offset from origin in mm
  67. #extruder.hotend.y_offset                        0            # Y offset from origin in mm
  68. #extruder.hotend.z_offset                        0            # Z offset from origin in mm
  69.  
  70. # Firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
  71. #extruder.hotend.retract_length                  3            # Retract length in mm
  72. #extruder.hotend.retract_feedrate                45           # Retract feedrate in mm/sec
  73. #extruder.hotend.retract_recover_length          0            # Additional length for recover
  74. #extruder.hotend.retract_recover_feedrate        8            # Recover feedrate in mm/sec (should be less than retract feedrate)
  75. #extruder.hotend.retract_zlift_length            0            # Z-lift on retract in mm, 0 disables
  76. #extruder.hotend.retract_zlift_feedrate          6000         # Z-lift feedrate in mm/min (Note mm/min NOT mm/sec)
  77.  
  78. delta_current                                    1.5          # First extruder stepper motor current
  79.  
  80. # Second extruder module configuration
  81. #extruder.hotend2.enable                         true         # Whether to activate the extruder module at all. All configuration is ignored if false
  82. #extruder.hotend2.steps_per_mm                   140          # Steps per mm for extruder stepper
  83. #extruder.hotend2.default_feed_rate              600          # Default rate ( mm/minute ) for moves where only the extruder moves
  84. #extruder.hotend2.acceleration                   500          # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
  85. #extruder.hotend2.max_speed                      50           # mm/s
  86.  
  87. #extruder.hotend2.step_pin                       2.8          # Pin for extruder step signal
  88. #extruder.hotend2.dir_pin                        2.13         # Pin for extruder dir signal ( add '!' to reverse direction )
  89. #extruder.hotend2.en_pin                         4.29         # Pin for extruder enable signal
  90.  
  91. #extruder.hotend2.x_offset                       0            # x offset from origin in mm
  92. #extruder.hotend2.y_offset                       25.0         # y offset from origin in mm
  93. #extruder.hotend2.z_offset                       0            # z offset from origin in mm
  94.  
  95. #epsilon_current                                 1.5          # Second extruder stepper motor current
  96.  
  97.  
  98. ## Laser module configuration
  99. # See http://smoothieware.org/laser
  100. laser_module_enable                           false           # Whether to activate the laser module at all
  101. laser_module_pwm_pin                          2.5             # This pin will be PWMed to control the laser.
  102.                                                               # Only pins 2.0, 2.1, 2.2, 2.3, 2.4, 2.5, 1.18, 1.20, 1.21, 1.23, 1.24, 1.26, 3.25 and 3.26
  103.                                                               # can be used since laser requires hardware PWM, see http://smoothieware.org/pinout
  104. #laser_module_ttl_pin                         1.30            # This pin turns on when the laser turns on, and off when the laser turns off.
  105. #laser_module_maximum_power                   1.0             # This is the maximum duty cycle that will be applied to the laser
  106. #laser_module_minimum_power                   0.0             # This is a value just below the minimum duty cycle that keeps the laser
  107.                                                               # active without actually burning.
  108. #laser_module_default_power                   0.8             # This is the default laser power that will be used for cuts if a power has not been specified.  The value is a scale between
  109.                                                               # the maximum and minimum power levels specified above
  110. #laser_module_pwm_period                      20              # This sets the pwm frequency as the period in microseconds
  111.  
  112. ## Temperature control configuration
  113. # See http://smoothieware.org/temperaturecontrol
  114.  
  115. # First hotend configuration
  116. temperature_control.hotend.enable            false             # Whether to activate this ( "hotend" ) module at all.
  117. temperature_control.hotend.thermistor_pin    0.23             # Pin for the thermistor to read
  118. temperature_control.hotend.heater_pin        2.7              # Pin that controls the heater, set to nc if a readonly thermistor is being defined
  119. temperature_control.hotend.thermistor        EPCOS100K        # See http://smoothieware.org/temperaturecontrol#toc5
  120. #temperature_control.hotend.beta             4066             # Or set the beta value
  121. temperature_control.hotend.set_m_code        104              # M-code to set the temperature for this module
  122. temperature_control.hotend.set_and_wait_m_code 109            # M-code to set-and-wait for this module
  123. temperature_control.hotend.designator        T                # Designator letter for this module
  124. #temperature_control.hotend.max_temp         300              # Set maximum temperature - Will prevent heating above 300 by default
  125. #temperature_control.hotend.min_temp         0                # Set minimum temperature - Will prevent heating below if set
  126.  
  127. # Safety control is enabled by default and can be overidden here, the values show the defaults
  128. # See http://smoothieware.org/temperaturecontrol#runaway
  129. #temperature_control.hotend.runaway_heating_timeout      900  # How long it can take to heat up, max is 2040 seconds.
  130. #temperature_control.hotend.runaway_cooling_timeout        0  # How long it can take to cool down if temp is set lower, max is 2040 seconds
  131. #temperature_control.hotend.runaway_range                20   # How far from the set temperature it can wander, max setting is 63°C
  132.  
  133. # PID configuration
  134. # See http://smoothieware.org/temperaturecontrol#pid
  135. #temperature_control.hotend.p_factor         13.7             # P ( proportional ) factor
  136. #temperature_control.hotend.i_factor         0.097            # I ( integral ) factor
  137. #temperature_control.hotend.d_factor         24               # D ( derivative ) factor
  138.  
  139. #temperature_control.hotend.max_pwm          64               # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  140.  
  141. # Second hotend configuration
  142. #temperature_control.hotend2.enable            true           # Whether to activate this ( "hotend" ) module at all.
  143. #temperature_control.hotend2.thermistor_pin    0.25           # Pin for the thermistor to read
  144. #temperature_control.hotend2.heater_pin        1.23           # Pin that controls the heater
  145. #temperature_control.hotend2.thermistor        EPCOS100K      # See http://smoothieware.org/temperaturecontrol#thermistor
  146. ##temperature_control.hotend2.beta             4066           # or set the beta value
  147. #temperature_control.hotend2.set_m_code        104            # M-code to set the temperature for this module
  148. #temperature_control.hotend2.set_and_wait_m_code 109          # M-code to set-and-wait for this module
  149. #temperature_control.hotend2.designator        T1             # Designator letter for this module
  150.  
  151. #temperature_control.hotend2.p_factor          13.7           # P ( proportional ) factor
  152. #temperature_control.hotend2.i_factor          0.097          # I ( integral ) factor
  153. #temperature_control.hotend2.d_factor          24             # D ( derivative ) factor
  154.  
  155. #temperature_control.hotend2.max_pwm          64              # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  156.  
  157. temperature_control.bed.enable               false             # Whether to activate this ( "hotend" ) module at all.
  158. temperature_control.bed.thermistor_pin       0.24             # Pin for the thermistor to read
  159. temperature_control.bed.heater_pin           2.5              # Pin that controls the heater
  160. temperature_control.bed.thermistor           Honeywell100K    # See http://smoothieware.org/temperaturecontrol#thermistor
  161. #temperature_control.bed.beta                3974             # Or set the beta value
  162. temperature_control.bed.set_m_code           140              # M-code to set the temperature for this module
  163. temperature_control.bed.set_and_wait_m_code  190              # M-code to set-and-wait for this module
  164. temperature_control.bed.designator           B                # Designator letter for this module
  165.  
  166. # Bang-bang ( simplified ) control
  167. # See http://smoothieware.org/temperaturecontrol#bang-bang
  168. #temperature_control.bed.bang_bang           false            # Set to true to use bang bang control rather than PID
  169. #temperature_control.bed.hysteresis          2.0              # Set to the temperature in degrees C to use as hysteresis
  170.  
  171. ## Switch modules
  172. # See http://smoothieware.org/switch
  173.  
  174. # Switch module for fan control
  175. switch.fan.enable                            false             # Enable this module
  176. switch.fan.input_on_command                  M106             # Command that will turn this switch on
  177. switch.fan.input_off_command                 M107             # Command that will turn this switch off
  178. switch.fan.output_pin                        2.6              # Pin this module controls
  179. switch.fan.output_type                       pwm              # PWM output settable with S parameter in the input_on_comand
  180. #switch.fan.max_pwm                          255              # Set max pwm for the pin default is 255
  181.  
  182. #switch.misc.enable                          true             # Enable this module
  183. #switch.misc.input_on_command                M42              # Command that will turn this switch on
  184. #switch.misc.input_off_command               M43              # Command that will turn this switch off
  185. #switch.misc.output_pin                      2.4              # Pin this module controls
  186. #switch.misc.output_type                     digital          # Digital means this is just an on or off pin
  187.  
  188. ## Temperatureswitch
  189. # See http://smoothieware.org/temperatureswitch
  190. # Automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
  191. # Useful to turn on a fan or water pump to cool the hotend
  192. #temperatureswitch.hotend.enable              true            #
  193. #temperatureswitch.hotend.designator          T               # first character of the temperature control designator to use as the temperature sensor to monitor
  194. #temperatureswitch.hotend.switch              misc            # select which switch to use, matches the name of the defined switch
  195. #temperatureswitch.hotend.threshold_temp      60.0            # temperature to turn on (if rising) or off the switch
  196. #temperatureswitch.hotend.heatup_poll         15              # poll heatup at 15 sec intervals
  197. #temperatureswitch.hotend.cooldown_poll       60              # poll cooldown at 60 sec intervals
  198.  
  199. ## Endstops
  200. # See http://smoothieware.org/endstops
  201. endstops_enable                              true             # The endstop module is enabled by default and can be disabled here
  202. #corexy_homing                               false            # Set to true if homing on a hbot or corexy
  203. alpha_min_endstop                            1.24^!            # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  204. #alpha_max_endstop                           1.25^            # Pin to read max endstop, uncomment this and comment the above if using max endstops
  205. alpha_homing_direction                       home_to_min      # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  206. alpha_min                                    0                # This gets loaded as the current position after homing when home_to_min is set
  207. alpha_max                                    200              # This gets loaded as the current position after homing when home_to_max is set
  208. beta_max_endstop                             1.26^!            # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  209. #beta_max_endstop                            1.27^            # Pin to read max endstop, uncomment this and comment the above if using max endstops
  210. beta_homing_direction                        home_to_min      # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  211. beta_min                                     0                # This gets loaded as the current position after homing when home_to_min is set
  212. beta_max                                     200              # This gets loaded as the current position after homing when home_to_max is set
  213. gamma_max_endstop                            1.28^!            # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  214. #gamma_max_endstop                           1.29^            # Pin to read max endstop, uncomment this and comment the above if using max endstops
  215. gamma_homing_direction                       home_to_max      # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  216. gamma_min                                    0                # This gets loaded as the current position after homing when home_to_min is set
  217. gamma_max                                    45              # This gets loaded as the current position after homing when home_to_max is set
  218.  
  219. alpha_max_travel                             5000              # Max travel in mm for alpha/X axis when homing
  220. beta_max_travel                              5000              # Max travel in mm for beta/Y axis when homing
  221. gamma_max_travel                             500              # Max travel in mm for gamma/Z axis when homing
  222.  
  223. # Optional enable limit switches, actions will stop if any enabled limit switch is triggered
  224. alpha_limit_enable                          true            # Set to true to enable X min and max limit switches
  225. beta_limit_enable                           true            # Set to true to enable Y min and max limit switches
  226. gamma_limit_enable                          true            # Set to true to enable Z min and max limit switches
  227.  
  228. # Endstops home at their fast feedrate first, then once the endstop is found they home again at their slow feedrate for accuracy
  229. alpha_fast_homing_rate_mm_s                  100               # Alpha/X fast homing feedrate in mm/second
  230. alpha_slow_homing_rate_mm_s                  25               # Alpha/X slow homing feedrate in mm/second
  231. beta_fast_homing_rate_mm_s                   100               # Beta/Y  fast homing feedrate in mm/second
  232. beta_slow_homing_rate_mm_s                   25               # Beta/Y  slow homing feedrate in mm/second
  233. gamma_fast_homing_rate_mm_s                  4                # Gamma/Z fast homing feedrate in mm/second
  234. gamma_slow_homing_rate_mm_s                  2                # Gamma/Z slow homing feedrate in mm/second
  235.  
  236. alpha_homing_retract_mm                      5                # Distance to retract from the endstop after it is hit for alpha/X
  237. beta_homing_retract_mm                       5                # Distance to retract from the endstop after it is hit for beta/Y
  238. gamma_homing_retract_mm                      1                # Distance to retract from the endstop after it is hit for gamma/Z
  239.  
  240.  
  241. # Optional enable limit switches, actions will stop if any enabled limit switch is triggered (all are set for delta)
  242. #alpha_limit_enable                          true            # Set to true to enable X min and max limit switches
  243. #beta_limit_enable                           true            # Set to true to enable Y min and max limit switches
  244. #gamma_limit_enable                          true            # Set to true to enable Z min and max limit switches
  245.  
  246. # Optional order in which axis will home, default is they all home at the same time,
  247. # If this is set it will force each axis to home one at a time in the specified order
  248. #homing_order                                 XYZ              # X axis followed by Y then Z last
  249. #move_to_origin_after_home                    false            # Move XY to 0,0 after homing
  250. #endstop_debounce_count                       100              # Uncomment if you get noise on your endstops, default is 100
  251. #endstop_debounce_ms                          1                # Uncomment if you get noise on your endstops, default is 1 millisecond debounce
  252. #home_z_first                                 true             # Uncomment and set to true to home the Z first, otherwise Z homes after XY
  253.  
  254. # End of endstop config
  255. # Delete the above endstop section and uncomment next line and copy and edit Snippets/abc-endstop.config file to enable endstops for ABC axis
  256. #include abc-endstop.config
  257.  
  258. ## Z-probe
  259. # See http://smoothieware.org/zprobe
  260. zprobe.enable                                false           # Set to true to enable a zprobe
  261. zprobe.probe_pin                             1.28!^          # Pin probe is attached to, if NC remove the !
  262. zprobe.slow_feedrate                         5               # Mm/sec probe feed rate
  263. #zprobe.debounce_ms                          1               # Set if noisy
  264. zprobe.fast_feedrate                         100             # Move feedrate mm/sec
  265. zprobe.probe_height                          5               # How much above bed to start probe
  266. #gamma_min_endstop                           nc              # Normally 1.28. Change to nc to prevent conflict,
  267.  
  268. # Levelling strategy
  269. # Example for 3-point levelling strategy, see wiki documentation for other strategies
  270. #leveling-strategy.three-point-leveling.enable         true        # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
  271. #leveling-strategy.three-point-leveling.point1         100.0,0.0   # the first probe point (x,y) optional may be defined with M557
  272. #leveling-strategy.three-point-leveling.point2         200.0,200.0 # the second probe point (x,y)
  273. #leveling-strategy.three-point-leveling.point3         0.0,200.0   # the third probe point (x,y)
  274. #leveling-strategy.three-point-leveling.home_first     true        # home the XY axis before probing
  275. #leveling-strategy.three-point-leveling.tolerance      0.03        # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
  276. #leveling-strategy.three-point-leveling.probe_offsets  0,0,0       # the probe offsets from nozzle, must be x,y,z, default is no offset
  277. #leveling-strategy.three-point-leveling.save_plane     false       # set to true to allow the bed plane to be saved with M500 default is false
  278.  
  279. ## Panel
  280. # See http://smoothieware.org/panel
  281. # Please find your panel on the wiki and copy/paste the right configuration here
  282. panel.enable                                 false             # Set to true to enable the panel code
  283.  
  284. # Example for reprap discount GLCD
  285. # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
  286. # +5v is EXP1 pin 10, Gnd is EXP1 pin 9
  287. #panel.lcd                                   reprap_discount_glcd     #
  288. #panel.spi_channel                           0                 # SPI channel to use  ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
  289. #panel.spi_cs_pin                            0.16              # SPI chip select     ; GLCD EXP1 Pin 4
  290. #panel.encoder_a_pin                         3.25!^            # Encoder pin         ; GLCD EXP2 Pin 3
  291. #panel.encoder_b_pin                         3.26!^            # Encoder pin         ; GLCD EXP2 Pin 5
  292. #panel.click_button_pin                      1.30!^            # Click button        ; GLCD EXP1 Pin 2
  293. #panel.buzz_pin                              1.31              # Pin for buzzer      ; GLCD EXP1 Pin 1
  294. #panel.back_button_pin                       2.11!^            # Back button         ; GLCD EXP2 Pin 8
  295.  
  296. panel.menu_offset                            0                 # Some panels will need 1 here
  297.  
  298. panel.alpha_jog_feedrate                     6000              # X jogging feedrate in mm/min
  299. panel.beta_jog_feedrate                      6000              # Y jogging feedrate in mm/min
  300. panel.gamma_jog_feedrate                     200               # Z jogging feedrate in mm/min
  301.  
  302. panel.hotend_temperature                     185               # Temp to set hotend when preheat is selected
  303. panel.bed_temperature                        60                # Temp to set bed when preheat is selected
  304.  
  305. ## Custom menus : Example of a custom menu entry, which will show up in the Custom entry.
  306. # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
  307. custom_menu.power_on.enable                true              #
  308. custom_menu.power_on.name                  Power_on          #
  309. custom_menu.power_on.command               M80               #
  310.  
  311. custom_menu.power_off.enable               true              #
  312. custom_menu.power_off.name                 Power_off         #
  313. custom_menu.power_off.command              M81               #
  314.  
  315.  
  316. ## Network settings
  317. # See http://smoothieware.org/network
  318. network.enable                               false            # Enable the ethernet network services
  319. network.webserver.enable                     true             # Enable the webserver
  320. network.telnet.enable                        true             # Enable the telnet server
  321. network.ip_address                           auto             # Use dhcp to get ip address
  322. # Uncomment the 3 below to manually setup ip address
  323. #network.ip_address                           192.168.3.222   # The IP address
  324. #network.ip_mask                              255.255.255.0   # The ip mask
  325. #network.ip_gateway                           192.168.3.1     # The gateway address
  326. #network.mac_override                         xx.xx.xx.xx.xx.xx  # Override the mac address, only do this if you have a conflict
  327.  
  328. ## System configuration
  329. # Serial communications configuration ( baud rate defaults to 9600 if undefined )
  330. # For communication over the UART port, *not* the USB/Serial port
  331. uart0.baud_rate                              115200           # Baud rate for the default hardware ( UART ) serial port
  332.  
  333. second_usb_serial_enable                     false            # This enables a second USB serial port
  334. #leds_disable                                true             # Disable using leds after config loaded
  335. #play_led_disable                            true             # Disable the play led
  336.  
  337. # Kill button maybe assigned to a different pin, set to the onboard pin by default
  338. # See http://smoothieware.org/killbutton
  339. kill_button_enable                           true             # Set to true to enable a kill button
  340. kill_button_pin                              2.12             # Kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
  341.  
  342. msd_disable                                 true            # Disable the MSD (USB SDCARD), see http://smoothieware.org/troubleshooting#disable-msd
  343. #dfu_enable                                  false            # For linux developers, set to true to enable DFU
  344.  
  345. # Only needed on a smoothieboard
  346. # See http://smoothieware.org/currentcontrol
  347. currentcontrol_module_enable                 true             # Control stepper motor current via the configuration file
  348. grbl_mode                                    true             # for correct use of G28 for MILL
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
 
Top