Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2019.08.25 12:00:51 =~=~=~=~=~=~=~=~=~=~=~=
- 16.971530] mt7603e 0000:01:00.0: Firmware Version: ap_pcie
- [ 16.977162] mt7603e 0000:01:00.0: Build Time: 20160107100755
- [ 17.017900] mt7603e 0000:01:00.0: firmware init done
- [ 17.072473] random: crng init done
- [ 17.075885] random: 6 urandom warning(s) missed due to ratelimiting
- [ 17.210835] bus=0x2, slot = 0x1, irq=0xff
- [ 17.214909] PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
- [ 17.220768] mt76x2e 0000:02:00.0: ASIC revision: 76120044
- [ 17.942903] mt76x2e 0000:02:00.0: ROM patch build: 20141115060606a
- [ 17.952580] mt76x2e 0000:02:00.0: Firmware Version: 0.0.00
- [ 17.958121] mt76x2e 0000:02:00.0: Build: 1
- [ 17.962199] mt76x2e 0000:02:00.0: Build Time: 201507311614____
- [ 17.987854] mt76x2e 0000:02:00.0: Firmware running!
- [ 18.006650] PPP generic driver version 2.4.2
- [ 18.012911] NET: Registered protocol family 24
- [ 18.020246] usbcore: registered new interface driver qmi_wwan
- [ 18.028310] usbcore: registered new interface driver rndis_host
- [ 18.036116] usbcore: registered new interface driver sierra
- [ 18.041886] usbserial: USB Serial support registered for Sierra USB modem
- [ 18.050723] usbcore: registered new interface driver sierra_net
- [ 18.102902] usbcore: registered new interface driver snd-usb-audio
- [ 18.114674] usbcore: registered new interface driver cdc_mbim
- [ 18.122369] usbcore: registered new interface driver option
- [ 18.128213] usbserial: USB Serial support registered for GSM modem (1-port)
- [ 18.140394] usbcore: registered new interface driver qcserial
- [ 18.146397] usbserial: USB Serial support registered for Qualcomm USB modem
- [ 18.153760] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 24.603773] mtk_soc_eth 1e100000.ethernet: PPE started
- [ 24.613740] device eth0 entered promiscuous mode
- [ 24.619879] br-lan: port 1(eth0.1) entered blocking state
- [ 24.625297] br-lan: port 1(eth0.1) entered disabled state
- [ 24.631507] device eth0.1 entered promiscuous mode
- [ 24.640530] br-lan: port 1(eth0.1) entered blocking state
- [ 24.645985] br-lan: port 1(eth0.1) entered forwarding state
- [ 24.652103] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
- [ 25.608409] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
- [ 27.962313] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 28.381348] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
- [ 28.387409] br-lan: port 2(wlan0) entered blocking state
- [ 28.392825] br-lan: port 2(wlan0) entered disabled state
- [ 28.398889] device wlan0 entered promiscuous mode
- [ 28.413224] br-lan: port 3(wlan1) entered blocking state
- [ 28.418578] br-lan: port 3(wlan1) entered disabled state
- [ 28.424612] device wlan1 entered promiscuous mode
- [ 28.429615] br-lan: port 3(wlan1) entered blocking state
- [ 28.434928] br-lan: port 3(wlan1) entered forwarding state
- [ 29.122647] br-lan: port 3(wlan1) entered disabled state
- [ 29.136808] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 29.143501] br-lan: port 2(wlan0) entered blocking state
- [ 29.148828] br-lan: port 2(wlan0) entered forwarding state
- [ 91.261203] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
- [ 91.267966] br-lan: port 3(wlan1) entered blocking state
- [ 91.273272] br-lan: port 3(wlan1) entered forwarding state
- [ 266.983066] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
- [ 290.478048] usb 2-1: USB disconnect, device number 2
- [ 338.738119] usb 2-1: new SuperSpeed USB device number 3 using xhci-mtk
- [ 338.775704] usb-storage 2-1:1.0: USB Mass Storage device detected
- [ 338.782499] scsi host0: usb-storage 2-1:1.0
- [ 340.032569] scsi 0:0:0:0: Direct-Access ADATA USB Flash Drive 1100 PQ: 0 ANSI: 6
- [ 340.042993] sd 0:0:0:0: [sda] 30310400 512-byte logical blocks: (15.5 GB/14.5 GiB)
- [ 340.051260] sd 0:0:0:0: [sda] Write Protect is off
- [ 340.056040] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
- [ 340.061744] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- [ 340.075827] sda: sda1
- [ 340.081744] sd 0:0:0:0: [sda] Attached SCSI removable disk
- [ 363.698071] usb 2-1: USB disconnect, device number 3
- [ 423.778176] usb 2-1: new SuperSpeed USB device number 4 using xhci-mtk
- [ 423.815619] usb-storage 2-1:1.0: USB Mass Storage device detected
- [ 423.822733] scsi host0: usb-storage 2-1:1.0
- [ 425.071006] scsi 0:0:0:0: Direct-Access ADATA USB Flash Drive 1100 PQ: 0 ANSI: 6
- [ 425.081515] sd 0:0:0:0: [sda] 30310400 512-byte logical blocks: (15.5 GB/14.5 GiB)
- [ 425.089780] sd 0:0:0:0: [sda] Write Protect is off
- [ 425.094558] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
- [ 425.100295] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- [ 425.114457] sda: sda1
- [ 425.120246] sd 0:0:0:0: [sda] Attached SCSI removable disk
- Watchdog handover: fd=3
- - watchdog -
- killall: telnetd: no process killed
- killall: ash: no process killed
- Sending TERM to remaining processes ... logd rpcd netifd odhcpd uhttpd smbd nmbd ntpd hostapd dnsmasq hostapd mount.ntfs-3g ubusd askfirst
- [ 573.758203] device wlan0 left promiscuous mode
- [ 573.762785] br-lan: port 2(wlan0) entered disabled state
- [ 573.835783] device wlan1 left promiscuous mode
- [ 573.840384] br-lan: port 3(wlan1) entered disabled state
- Sending KILL to remaining processes ...
- Switching to ramdisk...
- [ 580.588453] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
- [ 580.717787] UBIFS (ubi0:1): un-mount UBI device 0
- Performing system upgrade...
- Unlocking kernel ...
- Writing from <stdin> to kernel ... [ ][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w]
- removing ubiblock0_0
- [ 582.777924] block ubiblock0_0: released
- Volume ID 0, size 45 LEBs (5713920 bytes, 5.4 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs", alignment 1
- Set volume size to 110596096
- Volume ID 1, size 871 LEBs (110596096 bytes, 105.4 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs_data", alignment 1
- sysupgrade successful
- umount: can't unmount /dev: Resource busy
- umount: can't unmount /tmp: Resource busy
- [ 586.378075] sd 0:0:0:0: [sda] Synchronizing SCSI cache
- [ 586.384181] reboot: Restarting system
- ===================================================================
- MT7621 stage1 code 10:33:11 (ASIC)
- CPU=50000000 HZ BUS=12500000 HZ
- ==================================================================
- Change MPLL source from XTAL to CR...
- do MEMPLL setting..
- MEMPLL Config : 0x11100000
- 3PLL mode + External loopback
- === XTAL-40Mhz === DDR-1200Mhz ===
- PLL4 FB_DL: 0xe, 1/0 = 652/372 39000000
- PLL2 FB_DL: 0x13, 1/0 = 554/470 4D000000
- PLL3 FB_DL: 0x14, 1/0 = 812/212 51000000
- do DDR setting..[00320381]
- Apply DDR3 Setting...(use customer AC)
- 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120
- --------------------------------------------------------------------------------
- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1
- 000E:| 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
- 000F:| 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0
- 0010:| 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
- 0011:| 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- rank 0 coarse = 15
- rank 0 fine = 64
- B:| 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0
- opt_dle value:11
- DRAMC_R0DELDLY[018]=00001E1E
- ==================================================================
- RX DQS perbit delay software calibration
- ==================================================================
- 1.0-15 bit dq delay value
- ==================================================================
- bit| 0 1 2 3 4 5 6 7 8 9
- --------------------------------------
- 0 | 11 7 9 10 7 8 8 7 6 8
- 10 | 7 9 9 10 7 11
- --------------------------------------
- ==================================================================
- 2.dqs window
- x=pass dqs delay value (min~max)center
- y=0-7bit DQ of every group
- input delay:DQS0 =30 DQS1 = 30
- ==================================================================
- bit DQS0 bit DQS1
- 0 (2~58)30 8 (1~56)28
- 1 (1~56)28 9 (1~58)29
- 2 (2~57)29 10 (1~59)30
- 3 (1~55)28 11 (1~55)28
- 4 (1~55)28 12 (3~58)30
- 5 (1~58)29 13 (1~57)29
- 6 (1~56)28 14 (1~59)30
- 7 (1~59)30 15 (1~58)29
- ==================================================================
- 3.dq delay value last
- ==================================================================
- bit| 0 1 2 3 4 5 6 7 8 9
- --------------------------------------
- 0 | 11 9 10 12 9 9 10 7 8 9
- 10 | 7 11 9 11 7 12
- ==================================================================
- ==================================================================
- TX perbyte calibration
- ==================================================================
- DQS loop = 15, cmp_err_1 = ffff0000
- dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
- dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2
- DQ loop=15, cmp_err_1 = ffff0082
- dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1
- DQ loop=14, cmp_err_1 = ffff0000
- dqs_perbyte_dly.last_dqdly_pass[0]=14, finish count=2
- byte:0, (DQS,DQ)=(8,8)
- byte:1, (DQS,DQ)=(8,8)
- 20,data:88
- [EMI] DRAMC calibration passed
- ===================================================================
- MT7621 stage1 code done
- CPU=50000000 HZ BUS=12500000 HZ
- ===================================================================
- U-Boot 1.1.3 (May 24 2018 - 02:26:51)
- Board: Ralink APSoC DRAM: 256 MB
- Power on memory test. Memory size= 256 MB...OK!
- relocate_code Pointer at: 8ffac000
- Config XHCI 40M PLL
- ******************************
- Software System Reset Occurred
- ******************************
- Allocate 16 byte aligned buffer: 8ffe1090
- Enable NFI Clock
- # MTK NAND # : Use HW ECC
- NAND ID [C8 D1 80 95 42]
- Device not found, ID: c8d1
- Not Support this Device!
- chip_mode=00000001
- Support this Device in MTK table! c8d1
- select_chip
- [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
- Signature matched and data read!
- load_fact_bbt success 1023
- load fact bbt success
- [mtk_nand] probe successfully!
- mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
- ..============================================
- Ralink UBoot Version: 5.0.0.0
- --------------------------------------------
- ASIC MT7621A DualCore (MAC to MT7530 Mode)
- DRAM_CONF_FROM: Auto-Detection
- DRAM_TYPE: DDR3
- DRAM bus: 16 bit
- Xtal Mode=5 OCP Ratio=1/4
- Flash component: NAND Flash
- Date:May 24 2018 Time:02:26:51
- ============================================
- icache: sets:256, ways:4, linesz:32 ,total:32768
- dcache: sets:256, ways:4, linesz:32 ,total:32768
- ##### The CPU freq = 880 MHZ ####
- estimate memory size =256 Mbytes
- #Reset_MT7530
- set LAN/WAN LWLLL
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP.
- 4 3 2 1 0
- Booting System 2
- ..ranand_erase: start:80000, len:20000
- ..Done!
- done
- 3: System Boot system code via Flash.
- ## Booting image at bc600000 ...
- Image Name: MIPS OpenWrt Linux-4.14.138
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1870225 Bytes = 1.8 MB
- Load Address: 80001000
- Entry Point: 80001000
- ............................. Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- commandline uart_en=0 factory_mode=0 usb_u3=0
- No initrd
- ## Transferring control to Linux (at address 80001000) ...
- ## Giving linux memsize in MB, 256
- Starting kernel ...
- [ 0.000000] Linux version 4.14.138 (cezary@eko.one.pl) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10196-c4e727f01c)) #0 SMP Thu Aug 22 19:19:04 2019
- [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
- [ 0.000000] MIPS: machine is Xiaomi Mi Router 3G
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 10000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] VPE topology {2,2} total 4
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
- [ 0.000000] HighMem empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
- [ 0.000000] random: get_random_bytes called from 0x80575744 with crng_init=0
- [ 0.000000] percpu: Embedded 14 pages/cpu s26256 r8192 d22896 u57344
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024
- [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
- [ 0.000000] Writing ErrCtl register=00010000
- [ 0.000000] Readback ErrCtl register=00010000
- [ 0.000000] Memory: 253484K/262144K available (4753K kernel code, 238K rwdata, 584K rodata, 236K init, 254K bss, 8660K reserved, 0K cma-reserved, 0K highmem)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] NR_IRQS: 256
- [ 0.000000] CPU Clock: 880MHz
- [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
- [ 0.000010] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
- [ 0.007816] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
- [ 0.073979] pid_max: default: 32768 minimum: 301
- [ 0.078752] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.085260] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.094071] Hierarchical SRCU implementation.
- [ 0.099232] smp: Bringing up secondary CPUs ...
- [ 0.119488] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.119497] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.119509] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
- [ 0.119651] CPU1 revision is: 0001992f (MIPS 1004Kc)
- [ 0.163991] Synchronize counters for CPU 1: done.
- [ 0.213613] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.213622] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.213629] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
- [ 0.213703] CPU2 revision is: 0001992f (MIPS 1004Kc)
- [ 0.255127] Synchronize counters for CPU 2: done.
- [ 0.300643] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.300651] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.300659] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
- [ 0.300739] CPU3 revision is: 0001992f (MIPS 1004Kc)
- [ 0.340316] Synchronize counters for CPU 3: done.
- [ 0.370178] smp: Brought up 1 node, 4 CPUs
- [ 0.378064] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.387857] futex hash table entries: 1024 (order: 3, 32768 bytes)
- [ 0.394164] pinctrl core: initialized pinctrl subsystem
- [ 0.400828] NET: Registered protocol family 16
- [ 0.411296] pull PCIe RST: RALINK_RSTCTRL = 4000000
- [ 0.716597] release PCIe RST: RALINK_RSTCTRL = 7000000
- [ 0.721644] ***** Xtal 40MHz *****
- [ 0.725002] release PCIe RST: RALINK_RSTCTRL = 7000000
- [ 0.730099] Port 0 N_FTS = 1b105000
- [ 0.733570] Port 1 N_FTS = 1b105000
- [ 0.737009] Port 2 N_FTS = 1b102800
- [ 1.892367] PCIE2 no card, disable it(RST&CLK)
- [ 1.896728] -> 21007f2
- [ 1.899129] PCIE0 enabled
- [ 1.901721] PCIE1 enabled
- [ 1.904326] PCI host bridge /pcie@1e140000 ranges:
- [ 1.909098] MEM 0x0000000060000000..0x000000006fffffff
- [ 1.914259] IO 0x000000001e160000..0x000000001e16ffff
- [ 1.919455] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
- [ 1.935690] mt7621_gpio 1e000600.gpio: registering 32 gpios
- [ 1.941514] mt7621_gpio 1e000600.gpio: registering 32 gpios
- [ 1.947364] mt7621_gpio 1e000600.gpio: registering 32 gpios
- [ 1.954899] PCI host bridge to bus 0000:00
- [ 1.959006] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
- [ 1.965776] pci_bus 0000:00: root bus resource [io 0xffffffff]
- [ 1.971665] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
- [ 1.978388] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 1.988154] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
- [ 1.994667] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
- [ 2.001616] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
- [ 2.008138] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
- [ 2.015082] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
- [ 2.021799] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
- [ 2.028557] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref]
- [ 2.035706] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
- [ 2.042465] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
- [ 2.049189] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
- [ 2.055944] pci 0000:00:00.0: PCI bridge to [bus 01]
- [ 2.060851] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
- [ 2.067620] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
- [ 2.074855] pci 0000:02:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref]
- [ 2.082030] pci 0000:00:01.0: PCI bridge to [bus 02]
- [ 2.086937] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
- [ 2.093696] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff pref]
- [ 2.102198] clocksource: Switched to clocksource GIC
- [ 2.108708] NET: Registered protocol family 2
- [ 2.113761] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
- [ 2.120646] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
- [ 2.127102] TCP: Hash tables configured (established 2048 bind 2048)
- [ 2.133508] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 2.139268] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 2.145739] NET: Registered protocol family 1
- [ 2.382165] 4 CPUs re-calibrate udelay(lpj = 2924544)
- [ 2.388653] Crashlog allocated RAM at address 0x3f00000
- [ 2.394141] workingset: timestamp_bits=30 max_order=16 bucket_order=0
- [ 2.407141] random: fast init done
- [ 2.411394] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 2.417169] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 2.430485] io scheduler noop registered
- [ 2.434416] io scheduler deadline registered (default)
- [ 2.440576] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 2.450471] console [ttyS0] disabled
- [ 2.454049] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
- [ 2.463067] console [ttyS0] enabled
- [ 2.463067] console [ttyS0] enabled
- [ 2.469919] bootconsole [early0] disabled
- [ 2.469919] bootconsole [early0] disabled
- [ 2.478755] cacheinfo: Unable to detect cache hierarchy for CPU 0
- [ 2.485903] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
- [ 2.493035] Enable NFI Clock
- [ 2.495906] # MTK NAND # : Use HW ECC
- [ 2.499566] Device not found, ID: c8d1
- [ 2.503310] Not Support this Device!
- [ 2.507040] chip_mode=00000001
- [ 2.510078] Support this Device in MTK table! c8d1
- [ 2.515037] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
- [ 2.521495] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
- [ 2.527827] nand: ESMT NAND 128MiB 3,3V 8-bit
- [ 2.532179] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
- [ 2.539729] Scanning device for bad blocks
- [ 2.688886] 10 fixed-partitions partitions found on MTD device MT7621-NAND
- [ 2.695741] Creating 10 MTD partitions on "MT7621-NAND":
- [ 2.701035] 0x000000000000-0x000000080000 : "Bootloader"
- [ 2.707318] 0x000000080000-0x0000000c0000 : "Config"
- [ 2.713161] 0x0000000c0000-0x000000100000 : "Bdata"
- [ 2.718876] 0x000000100000-0x000000140000 : "Factory"
- [ 2.724831] 0x000000140000-0x000000180000 : "crash"
- [ 2.730549] 0x000000180000-0x0000001c0000 : "crash_syslog"
- [ 2.736943] 0x0000001c0000-0x000000200000 : "reserved0"
- [ 2.743120] 0x000000200000-0x000000600000 : "kernel_stock"
- [ 2.749485] 0x000000600000-0x000000a00000 : "kernel"
- [ 2.755416] 0x000000a00000-0x000007f80000 : "ubi"
- [ 2.761946] [mtk_nand] probe successfully!
- [ 2.766779] Signature matched and data read!
- [ 2.771025] load_fact_bbt success 1023
- [ 2.775529] libphy: Fixed MDIO Bus: probed
- [ 2.844770] libphy: mdio: probed
- [ 4.248352] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
- [ 4.255002] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
- [ 4.265722] NET: Registered protocol family 10
- [ 4.271723] Segment Routing with IPv6
- [ 4.275512] NET: Registered protocol family 17
- [ 4.280009] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
- [ 4.292923] 8021q: 802.1Q VLAN Support v1.8
- [ 4.300123] UBI: auto-attach mtd9
- [ 4.303512] ubi0: attaching mtd9
- [ 5.390322] ubi0: scanning is finished
- [ 5.410019] ubi0: attached mtd9 (name "ubi", size 117 MiB)
- [ 5.415521] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
- [ 5.422378] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
- [ 5.429132] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
- [ 5.436072] ubi0: good PEBs: 940, bad PEBs: 0, corrupted PEBs: 0
- [ 5.442048] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
- [ 5.449250] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1700740608
- [ 5.458352] ubi0: available PEBs: 0, total reserved PEBs: 940, PEBs reserved for bad PEB handling: 20
- [ 5.467566] ubi0: background thread "ubi_bgt0d" started, PID 395
- [ 5.469313] block ubiblock0_0: created from ubi0:0(rootfs)
- [ 5.479040] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
- [ 5.485991] hctosys: unable to open rtc device (rtc0)
- [ 5.491269] usb_vbus: disabling
- [ 5.500412] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
- [ 5.508093] Freeing unused kernel memory: 236K
- [ 5.512562] This architecture does not have kernel memory protection.
- [ 6.065776] init: Console is alive
- [ 6.069428] init: - watchdog -
- [ 7.261752] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 7.380685] usbcore: registered new interface driver usbfs
- [ 7.386296] usbcore: registered new interface driver hub
- [ 7.391748] usbcore: registered new device driver usb
- [ 7.420912] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 7.433691] SCSI subsystem initialized
- [ 7.440819] ehci-platform: EHCI generic platform driver
- [ 7.451984] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
- [ 7.461004] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
- [ 7.466368] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
- [ 7.482340] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
- [ 7.491517] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
- [ 7.498305] hub 1-0:1.0: USB hub found
- [ 7.502128] hub 1-0:1.0: 2 ports detected
- [ 7.506832] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
- [ 7.512199] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
- [ 7.519664] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
- [ 7.526276] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
- [ 7.535261] hub 2-0:1.0: USB hub found
- [ 7.539077] hub 2-0:1.0: 1 port detected
- [ 7.550680] usbcore: registered new interface driver usb-storage
- [ 7.558236] usbcore: registered new interface driver uas
- [ 7.563856] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 7.572543] init: - preinit -
- [ 8.032578] usb 2-1: new SuperSpeed USB device number 2 using xhci-mtk
- [ 8.069562] random: procd: uninitialized urandom read (4 bytes read)
- [ 8.077849] usb-storage 2-1:1.0: USB Mass Storage device detected
- [ 8.084493] scsi host0: usb-storage 2-1:1.0
- [ 8.505552] mtk_soc_eth 1e100000.ethernet: PPE started
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 9.305374] scsi 0:0:0:0: Direct-Access ADATA USB Flash Drive 1100 PQ: 0 ANSI: 6
- [ 9.315455] sd 0:0:0:0: [sda] 30310400 512-byte logical blocks: (15.5 GB/14.5 GiB)
- [ 9.323651] sd 0:0:0:0: [sda] Write Protect is off
- [ 9.329037] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- [ 9.343196] sda: sda1
- [ 9.348552] sd 0:0:0:0: [sda] Attached SCSI removable disk
- [ 11.739541] mount_root: loading kmods from internal overlay
- [ 11.771846] kmodloader: loading kernel modules from //etc/modules-boot.d/*
- [ 11.779920] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
- [ 12.042990] UBIFS (ubi0:1): default file-system created
- [ 12.049714] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 547
- [ 12.164058] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
- [ 12.171871] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
- [ 12.181816] UBIFS (ubi0:1): FS size: 109199360 bytes (104 MiB, 860 LEBs), journal size 5459968 bytes (5 MiB, 43 LEBs)
- [ 12.192406] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
- [ 12.198993] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 6001D1F2-03D2-41B7-BC09-8C5FB8B3834D, small LPT model
- [ 12.211772] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
- [ 12.218909] block: unable to load configuration (fstab: Entry not found)
- [ 12.225687] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
- [ 12.232262] block: unable to load configuration (fstab: Entry not found)
- [ 12.239000] block: attempting to load /etc/config/fstab
- [ 12.247961] block: unable to load configuration (fstab: Entry not found)
- [ 12.254745] block: no usable configuration
- [ 12.297320] UBIFS (ubi0:1): un-mount UBI device 0
- [ 12.302037] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
- [ 12.314322] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 550
- [ 12.427082] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
- [ 12.434950] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
- [ 12.444865] UBIFS (ubi0:1): FS size: 109199360 bytes (104 MiB, 860 LEBs), journal size 5459968 bytes (5 MiB, 43 LEBs)
- [ 12.455441] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
- [ 12.462028] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 6001D1F2-03D2-41B7-BC09-8C5FB8B3834D, small LPT model
- [ 12.674302] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
- [ 12.681363] block: unable to load configuration (fstab: Entry not found)
- [ 12.688194] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
- [ 12.694785] block: unable to load configuration (fstab: Entry not found)
- [ 12.701533] block: attempting to load /etc/config/fstab
- [ 12.706862] block: unable to load configuration (fstab: Entry not found)
- [ 12.713637] block: no usable configuration
- [ 12.754321] mount_root: overlay filesystem has not been fully initialized yet
- [ 12.761848] mount_root: switching to ubifs overlay
- [ 12.799036] urandom-seed: Seed file not found (/etc/urandom.seed)
- [ 12.873221] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
- [ 12.888328] procd: - early -
- [ 12.891306] procd: - watchdog -
- [ 13.552710] random: jshn: uninitialized urandom read (4 bytes read)
- Failed to connect to ubus
- [ 13.662448] procd: - watchdog -
- [ 13.666050] procd: - ubus -
- [ 13.767841] random: jshn: uninitialized urandom read (4 bytes read)
- [ 13.805051] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 13.891196] procd: - init -
- Please press Enter to activate this console.
- [ 14.329436] urngd: v1.0.0 started.
- [ 14.449394] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 14.468832] tun: Universal TUN/TAP device driver, 1.6
- [ 14.483731] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 14.499801] fuse init (API version 7.26)
- [ 14.511786] usbcore: registered new interface driver cdc_acm
- [ 14.517540] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
- [ 14.522475] random: crng init done
- [ 14.527661] usbcore: registered new interface driver cdc_wdm
- [ 14.528923] random: 6 urandom warning(s) missed due to ratelimiting
- [ 14.536450] Loading modules backported from Linux version v4.19.66-0-g893af1c79e42
- [ 14.548525] Backport generated by backports.git v4.19.66-1-0-g354501da
- [ 14.557236] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 14.571864] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
- [ 14.672681] usbcore: registered new interface driver usblp
- [ 14.685342] usbcore: registered new interface driver usbserial
- [ 14.691469] usbcore: registered new interface driver usbserial_generic
- [ 14.698249] usbserial: USB Serial support registered for generic
- [ 14.709746] wireguard: WireGuard 0.0.20190601 loaded. See www.wireguard.com for information.
- [ 14.718262] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
- [ 14.742613] xt_time: kernel timezone is -0000
- [ 14.748542] usbcore: registered new interface driver cdc_ether
- [ 14.756900] usbcore: registered new interface driver cdc_ncm
- [ 14.794127] usbcore: registered new interface driver huawei_cdc_ncm
- [ 14.847184] bus=0x1, slot = 0x0, irq=0xff
- [ 14.851504] mt7603e 0000:01:00.0: ASIC revision: 76030010
- [ 15.884840] mt7603e 0000:01:00.0: Firmware Version: ap_pcie
- [ 15.890415] mt7603e 0000:01:00.0: Build Time: 20160107100755
- [ 15.932199] mt7603e 0000:01:00.0: firmware init done
- [ 16.121365] bus=0x2, slot = 0x1, irq=0xff
- [ 16.125754] mt76x2e 0000:02:00.0: ASIC revision: 76120044
- [ 16.848750] mt76x2e 0000:02:00.0: ROM patch build: 20141115060606a
- [ 16.858437] mt76x2e 0000:02:00.0: Firmware Version: 0.0.00
- [ 16.863972] mt76x2e 0000:02:00.0: Build: 1
- [ 16.868050] mt76x2e 0000:02:00.0: Build Time: 201507311614____
- [ 16.892209] mt76x2e 0000:02:00.0: Firmware running!
- [ 16.910885] PPP generic driver version 2.4.2
- [ 16.917035] NET: Registered protocol family 24
- [ 16.924490] usbcore: registered new interface driver qmi_wwan
- [ 16.932493] usbcore: registered new interface driver rndis_host
- [ 16.940223] usbcore: registered new interface driver sierra
- [ 16.946006] usbserial: USB Serial support registered for Sierra USB modem
- [ 16.955413] usbcore: registered new interface driver sierra_net
- [ 16.965449] usbcore: registered new interface driver cdc_mbim
- [ 16.973057] usbcore: registered new interface driver option
- [ 16.978864] usbserial: USB Serial support registered for GSM modem (1-port)
- [ 16.990228] usbcore: registered new interface driver qcserial
- [ 16.996293] usbserial: USB Serial support registered for Qualcomm USB modem
- [ 17.003700] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 33.644726] mtk_soc_eth 1e100000.ethernet: PPE started
- [ 33.654414] device eth0 entered promiscuous mode
- [ 33.659689] br-lan: port 1(eth0.1) entered blocking state
- [ 33.665351] br-lan: port 1(eth0.1) entered disabled state
- [ 33.671488] device eth0.1 entered promiscuous mode
- [ 33.679786] br-lan: port 1(eth0.1) entered blocking state
- [ 33.685231] br-lan: port 1(eth0.1) entered forwarding state
- [ 33.691501] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
- [ 34.642945] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
- [ 109.914054] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up
- [ 189.231779] mtk_soc_eth 1e100000.ethernet eth0: port 1 link down
- [ 194.072078] mtk_soc_eth 1e100000.ethernet eth0: port 2 link up
- [ 341.680433] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 341.694406] br-lan: port 2(wlan0) entered blocking state
- [ 341.699867] br-lan: port 2(wlan0) entered disabled state
- [ 341.705956] device wlan0 entered promiscuous mode
- [ 342.113746] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 342.120427] br-lan: port 2(wlan0) entered blocking state
- [ 342.125781] br-lan: port 2(wlan0) entered forwarding state
- [ 408.715208] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
- [ 408.724688] br-lan: port 3(wlan1) entered blocking state
- [ 408.729996] br-lan: port 3(wlan1) entered disabled state
- [ 408.735865] device wlan1 entered promiscuous mode
- [ 475.246932] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
- [ 475.253702] br-lan: port 3(wlan1) entered blocking state
- [ 475.259052] br-lan: port 3(wlan1) entered forwarding state
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement