API tools faq
paste
Advertisement
Guest User

GeeeTech i3 Pro B Marlin 1.1.8 No ABL Configuration.h

a guest
Dec 26th, 2017
1,805
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
C++ 66.60 KB | None | 0 0
raw download clone embed print report
  1. /**
  2.  * Marlin 3D Printer Firmware
  3.  * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  4.  *
  5.  * Based on Sprinter and grbl.
  6.  * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  7.  *
  8.  * This program is free software: you can redistribute it and/or modify
  9.  * it under the terms of the GNU General Public License as published by
  10.  * the Free Software Foundation, either version 3 of the License, or
  11.  * (at your option) any later version.
  12.  *
  13.  * This program is distributed in the hope that it will be useful,
  14.  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15.  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  16.  * GNU General Public License for more details.
  17.  *
  18.  * You should have received a copy of the GNU General Public License
  19.  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  20.  *
  21.  */
  22.  
  23. /**
  24.  * Configuration.h
  25.  *
  26.  * Basic settings such as:
  27.  *
  28.  * - Type of electronics
  29.  * - Type of temperature sensor
  30.  * - Printer geometry
  31.  * - Endstop configuration
  32.  * - LCD controller
  33.  * - Extra features
  34.  *
  35.  * Advanced settings can be found in Configuration_adv.h
  36.  *
  37.  */
  38. #ifndef CONFIGURATION_H
  39. #define CONFIGURATION_H
  40. #define CONFIGURATION_H_VERSION 010107
  41.  
  42. //===========================================================================
  43. //============================= Getting Started =============================
  44. //===========================================================================
  45.  
  46. /**
  47.  * Here are some standard links for getting your machine calibrated:
  48.  *
  49.  * http://reprap.org/wiki/Calibration
  50.  * http://youtu.be/wAL9d7FgInk
  51.  * http://calculator.josefprusa.cz
  52.  * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
  53.  * http://www.thingiverse.com/thing:5573
  54.  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  55.  * http://www.thingiverse.com/thing:298812
  56.  */
  57.  
  58. //===========================================================================
  59. //============================= DELTA Printer ===============================
  60. //===========================================================================
  61. // For a Delta printer start with one of the configuration files in the
  62. // example_configurations/delta directory and customize for your machine.
  63. //
  64.  
  65. //===========================================================================
  66. //============================= SCARA Printer ===============================
  67. //===========================================================================
  68. // For a SCARA printer start with the configuration files in
  69. // example_configurations/SCARA and customize for your machine.
  70. //
  71.  
  72. // @section info
  73.  
  74. // User-specified version info of this build to display in [Pronterface, etc] terminal window during
  75. // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
  76. // build by the user have been successfully uploaded into firmware.
  77. #define STRING_CONFIG_H_AUTHOR "(Solo761, GT i3 Pro B)" // Who made the changes.
  78. #define SHOW_BOOTSCREEN
  79. #define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
  80. #define STRING_SPLASH_LINE2 WEBSITE_URL         // will be shown during bootup in line 2
  81.  
  82. //
  83. // *** VENDORS PLEASE READ *****************************************************
  84. //
  85. // Marlin now allow you to have a vendor boot image to be displayed on machine
  86. // start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
  87. // custom boot image and then the default Marlin boot image is shown.
  88. //
  89. // We suggest for you to take advantage of this new feature and keep the Marlin
  90. // boot image unmodified. For an example have a look at the bq Hephestos 2
  91. // example configuration folder.
  92. //
  93. //#define SHOW_CUSTOM_BOOTSCREEN
  94. // @section machine
  95.  
  96. /**
  97.  * Select which serial port on the board will be used for communication with the host.
  98.  * This allows the connection of wireless adapters (for instance) to non-default port pins.
  99.  * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
  100.  *
  101.  * :[0, 1, 2, 3, 4, 5, 6, 7]
  102.  */
  103. #define SERIAL_PORT 0
  104.  
  105. /**
  106.  * This setting determines the communication speed of the printer.
  107.  *
  108.  * 250000 works in most cases, but you might try a lower speed if
  109.  * you commonly experience drop-outs during host printing.
  110.  * You may try up to 1000000 to speed up SD file transfer.
  111.  *
  112.  * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  113.  */
  114. #define BAUDRATE 250000
  115.  
  116. // Enable the Bluetooth serial interface on AT90USB devices
  117. //#define BLUETOOTH
  118.  
  119. // The following define selects which electronics board you have.
  120. // Please choose the name from boards.h that matches your setup
  121. #ifndef MOTHERBOARD
  122.   #define MOTHERBOARD BOARD_GT2560_REV_A_PLUS
  123. #endif
  124.  
  125. // Optional custom name for your RepStrap or other custom machine
  126. // Displayed in the LCD "Ready" message
  127. #define CUSTOM_MACHINE_NAME "GT i3 Pro B"
  128.  
  129. // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
  130. // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
  131. //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  132. #define MACHINE_UUID "171bf5f7-f61b-4f59-bb61-78a02c6e263a"
  133.  
  134. // @section extruder
  135.  
  136. // This defines the number of extruders
  137. // :[1, 2, 3, 4, 5]
  138. #define EXTRUDERS 1
  139.  
  140. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
  141. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
  142.  
  143. // For Cyclops or any "multi-extruder" that shares a single nozzle.
  144. //#define SINGLENOZZLE
  145.  
  146. /**
  147.  * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
  148.  *
  149.  * This device allows one stepper driver on a control board to drive
  150.  * two to eight stepper motors, one at a time, in a manner suitable
  151.  * for extruders.
  152.  *
  153.  * This option only allows the multiplexer to switch on tool-change.
  154.  * Additional options to configure custom E moves are pending.
  155.  */
  156. //#define MK2_MULTIPLEXER
  157. #if ENABLED(MK2_MULTIPLEXER)
  158.   // Override the default DIO selector pins here, if needed.
  159.   // Some pins files may provide defaults for these pins.
  160.   //#define E_MUX0_PIN 40  // Always Required
  161.   //#define E_MUX1_PIN 42  // Needed for 3 to 8 steppers
  162.   //#define E_MUX2_PIN 44  // Needed for 5 to 8 steppers
  163. #endif
  164.  
  165. // A dual extruder that uses a single stepper motor
  166. //#define SWITCHING_EXTRUDER
  167. #if ENABLED(SWITCHING_EXTRUDER)
  168.   #define SWITCHING_EXTRUDER_SERVO_NR 0
  169.   #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
  170.   #if EXTRUDERS > 3
  171.     #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
  172.   #endif
  173. #endif
  174.  
  175. // A dual-nozzle that uses a servomotor to raise/lower one of the nozzles
  176. //#define SWITCHING_NOZZLE
  177. #if ENABLED(SWITCHING_NOZZLE)
  178.   #define SWITCHING_NOZZLE_SERVO_NR 0
  179.   #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
  180.   //#define HOTEND_OFFSET_Z { 0.0, 0.0 }
  181. #endif
  182.  
  183. /**
  184.  * Two separate X-carriages with extruders that connect to a moving part
  185.  * via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
  186.  */
  187. //#define PARKING_EXTRUDER
  188. #if ENABLED(PARKING_EXTRUDER)
  189.   #define PARKING_EXTRUDER_SOLENOIDS_INVERT           // If enabled, the solenoid is NOT magnetized with applied voltage
  190.   #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW  // LOW or HIGH pin signal energizes the coil
  191.   #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250        // Delay (ms) for magnetic field. No delay if 0 or not defined.
  192.   #define PARKING_EXTRUDER_PARKING_X { -78, 184 }     // X positions for parking the extruders
  193.   #define PARKING_EXTRUDER_GRAB_DISTANCE 1            // mm to move beyond the parking point to grab the extruder
  194.   #define PARKING_EXTRUDER_SECURITY_RAISE 5           // Z-raise before parking
  195.   #define HOTEND_OFFSET_Z { 0.0, 1.3 }                // Z-offsets of the two hotends. The first must be 0.
  196. #endif
  197.  
  198. /**
  199.  * "Mixing Extruder"
  200.  *   - Adds a new code, M165, to set the current mix factors.
  201.  *   - Extends the stepping routines to move multiple steppers in proportion to the mix.
  202.  *   - Optional support for Repetier Firmware M163, M164, and virtual extruder.
  203.  *   - This implementation supports only a single extruder.
  204.  *   - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation
  205.  */
  206. //#define MIXING_EXTRUDER
  207. #if ENABLED(MIXING_EXTRUDER)
  208.   #define MIXING_STEPPERS 2        // Number of steppers in your mixing extruder
  209.   #define MIXING_VIRTUAL_TOOLS 16  // Use the Virtual Tool method with M163 and M164
  210.   //#define DIRECT_MIXING_IN_G1    // Allow ABCDHI mix factors in G1 movement commands
  211. #endif
  212.  
  213. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  214. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  215. // For the other hotends it is their distance from the extruder 0 hotend.
  216. //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
  217. //#define HOTEND_OFFSET_Y {0.0, 5.00}  // (in mm) for each extruder, offset of the hotend on the Y axis
  218.  
  219. // @section machine
  220.  
  221. /**
  222.  * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
  223.  *
  224.  * 0 = No Power Switch
  225.  * 1 = ATX
  226.  * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
  227.  *
  228.  * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
  229.  */
  230. #define POWER_SUPPLY 1
  231.  
  232. #if POWER_SUPPLY > 0
  233.   // Enable this option to leave the PSU off at startup.
  234.   // Power to steppers and heaters will need to be turned on with M80.
  235.   //#define PS_DEFAULT_OFF
  236. #endif
  237.  
  238. // @section temperature
  239.  
  240. //===========================================================================
  241. //============================= Thermal Settings ============================
  242. //===========================================================================
  243.  
  244. /**
  245.  * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  246.  *
  247.  * Temperature sensors available:
  248.  *
  249.  *    -3 : thermocouple with MAX31855 (only for sensor 0)
  250.  *    -2 : thermocouple with MAX6675 (only for sensor 0)
  251.  *    -1 : thermocouple with AD595
  252.  *     0 : not used
  253.  *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  254.  *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  255.  *     3 : Mendel-parts thermistor (4.7k pullup)
  256.  *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  257.  *     5 : 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
  258.  *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  259.  *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  260.  *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  261.  *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  262.  *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  263.  *    10 : 100k RS thermistor 198-961 (4.7k pullup)
  264.  *    11 : 100k beta 3950 1% thermistor (4.7k pullup)
  265.  *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  266.  *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  267.  *    20 : the PT100 circuit found in the Ultimainboard V2.x
  268.  *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  269.  *    66 : 4.7M High Temperature thermistor from Dyze Design
  270.  *    70 : the 100K thermistor found in the bq Hephestos 2
  271.  *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
  272.  *
  273.  *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  274.  *                              (but gives greater accuracy and more stable PID)
  275.  *    51 : 100k thermistor - EPCOS (1k pullup)
  276.  *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  277.  *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  278.  *
  279.  *  1047 : Pt1000 with 4k7 pullup
  280.  *  1010 : Pt1000 with 1k pullup (non standard)
  281.  *   147 : Pt100 with 4k7 pullup
  282.  *   110 : Pt100 with 1k pullup (non standard)
  283.  *
  284.  *         Use these for Testing or Development purposes. NEVER for production machine.
  285.  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  286.  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  287.  *
  288.  * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
  289.  */
  290. #define TEMP_SENSOR_0 1
  291. #define TEMP_SENSOR_1 0
  292. #define TEMP_SENSOR_2 0
  293. #define TEMP_SENSOR_3 0
  294. #define TEMP_SENSOR_4 0
  295. #define TEMP_SENSOR_BED 1
  296.  
  297. // Dummy thermistor constant temperature readings, for use with 998 and 999
  298. #define DUMMY_THERMISTOR_998_VALUE 25
  299. #define DUMMY_THERMISTOR_999_VALUE 100
  300.  
  301. // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
  302. // from the two sensors differ too much the print will be aborted.
  303. //#define TEMP_SENSOR_1_AS_REDUNDANT
  304. #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
  305.  
  306. // Extruder temperature must be close to target for this long before M109 returns success
  307. #define TEMP_RESIDENCY_TIME 10  // (seconds)
  308. #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
  309. #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
  310.  
  311. // Bed temperature must be close to target for this long before M190 returns success
  312. #define TEMP_BED_RESIDENCY_TIME 10  // (seconds)
  313. #define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
  314. #define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
  315.  
  316. // The minimal temperature defines the temperature below which the heater will not be enabled It is used
  317. // to check that the wiring to the thermistor is not broken.
  318. // Otherwise this would lead to the heater being powered on all the time.
  319. #define HEATER_0_MINTEMP 5
  320. #define HEATER_1_MINTEMP 5
  321. #define HEATER_2_MINTEMP 5
  322. #define HEATER_3_MINTEMP 5
  323. #define HEATER_4_MINTEMP 5
  324. #define BED_MINTEMP 5
  325.  
  326. // When temperature exceeds max temp, your heater will be switched off.
  327. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
  328. // You should use MINTEMP for thermistor short/failure protection.
  329. #define HEATER_0_MAXTEMP 275
  330. #define HEATER_1_MAXTEMP 275
  331. #define HEATER_2_MAXTEMP 275
  332. #define HEATER_3_MAXTEMP 275
  333. #define HEATER_4_MAXTEMP 275
  334. #define BED_MAXTEMP 150
  335.  
  336. //===========================================================================
  337. //============================= PID Settings ================================
  338. //===========================================================================
  339. // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
  340.  
  341. // Comment the following line to disable PID and enable bang-bang.
  342. #define PIDTEMP
  343. #define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
  344. #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
  345. #define PID_K1 0.95      // Smoothing factor within the PID
  346. #if ENABLED(PIDTEMP)
  347.   //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
  348.   //#define PID_DEBUG // Sends debug data to the serial port.
  349.   //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  350.   //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  351.   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
  352.                                   // Set/get with gcode: M301 E[extruder number, 0-2]
  353.   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
  354.                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
  355.  
  356.   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  357.  
  358.   // Ultimaker
  359.   #define  DEFAULT_Kp 22.2
  360.   #define  DEFAULT_Ki 1.08
  361.   #define  DEFAULT_Kd 114
  362.  
  363.   // MakerGear
  364.   //#define  DEFAULT_Kp 7.0
  365.   //#define  DEFAULT_Ki 0.1
  366.   //#define  DEFAULT_Kd 12
  367.  
  368.   // Mendel Parts V9 on 12V
  369.   //#define  DEFAULT_Kp 63.0
  370.   //#define  DEFAULT_Ki 2.25
  371.   //#define  DEFAULT_Kd 440
  372.  
  373. #endif // PIDTEMP
  374.  
  375. //===========================================================================
  376. //============================= PID > Bed Temperature Control ===============
  377. //===========================================================================
  378. // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
  379. //
  380. // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
  381. // If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
  382. // which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
  383. // This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
  384. // If your configuration is significantly different than this and you don't understand the issues involved, you probably
  385. // shouldn't use bed PID until someone else verifies your hardware works.
  386. // If this is enabled, find your own PID constants below.
  387. //#define PIDTEMPBED
  388.  
  389. //#define BED_LIMIT_SWITCHING
  390.  
  391. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
  392. // all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
  393. // setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
  394. // so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
  395. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  396.  
  397. #if ENABLED(PIDTEMPBED)
  398.  
  399.   //#define PID_BED_DEBUG // Sends debug data to the serial port.
  400.  
  401.   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  402.   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  403.   #define  DEFAULT_bedKp 10.00
  404.   #define  DEFAULT_bedKi .023
  405.   #define  DEFAULT_bedKd 305.4
  406.  
  407.   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  408.   //from pidautotune
  409.   //#define  DEFAULT_bedKp 97.1
  410.   //#define  DEFAULT_bedKi 1.41
  411.   //#define  DEFAULT_bedKd 1675.16
  412.  
  413.   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  414. #endif // PIDTEMPBED
  415.  
  416. // @section extruder
  417.  
  418. // This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP.
  419. // It also enables the M302 command to set the minimum extrusion temperature
  420. // or to allow moving the extruder regardless of the hotend temperature.
  421. // *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
  422. #define PREVENT_COLD_EXTRUSION
  423. #define EXTRUDE_MINTEMP 170
  424.  
  425. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
  426. // Note that for Bowden Extruders a too-small value here may prevent loading.
  427. #define PREVENT_LENGTHY_EXTRUDE
  428. #define EXTRUDE_MAXLENGTH 200
  429.  
  430. //===========================================================================
  431. //======================== Thermal Runaway Protection =======================
  432. //===========================================================================
  433.  
  434. /**
  435.  * Thermal Protection provides additional protection to your printer from damage
  436.  * and fire. Marlin always includes safe min and max temperature ranges which
  437.  * protect against a broken or disconnected thermistor wire.
  438.  *
  439.  * The issue: If a thermistor falls out, it will report the much lower
  440.  * temperature of the air in the room, and the the firmware will keep
  441.  * the heater on.
  442.  *
  443.  * If you get "Thermal Runaway" or "Heating failed" errors the
  444.  * details can be tuned in Configuration_adv.h
  445.  */
  446.  
  447. #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
  448. #define THERMAL_PROTECTION_BED     // Enable thermal protection for the heated bed
  449.  
  450. //===========================================================================
  451. //============================= Mechanical Settings =========================
  452. //===========================================================================
  453.  
  454. // @section machine
  455.  
  456. // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
  457. // either in the usual order or reversed
  458. //#define COREXY
  459. //#define COREXZ
  460. //#define COREYZ
  461. //#define COREYX
  462. //#define COREZX
  463. //#define COREZY
  464.  
  465. //===========================================================================
  466. //============================== Endstop Settings ===========================
  467. //===========================================================================
  468.  
  469. // @section homing
  470.  
  471. // Specify here all the endstop connectors that are connected to any endstop or probe.
  472. // Almost all printers will be using one per axis. Probes will use one or more of the
  473. // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
  474. #define USE_XMIN_PLUG
  475. #define USE_YMIN_PLUG
  476. #define USE_ZMIN_PLUG
  477. //#define USE_XMAX_PLUG
  478. //#define USE_YMAX_PLUG
  479. //#define USE_ZMAX_PLUG
  480.  
  481. // coarse Endstop Settings
  482. #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
  483.  
  484. #if DISABLED(ENDSTOPPULLUPS)
  485.   // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
  486.   //#define ENDSTOPPULLUP_XMAX
  487.   //#define ENDSTOPPULLUP_YMAX
  488.   //#define ENDSTOPPULLUP_ZMAX
  489.   //#define ENDSTOPPULLUP_XMIN
  490.   //#define ENDSTOPPULLUP_YMIN
  491.   //#define ENDSTOPPULLUP_ZMIN
  492.   //#define ENDSTOPPULLUP_ZMIN_PROBE
  493. #endif
  494.  
  495. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
  496. #define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  497. #define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  498. #define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  499. #define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  500. #define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  501. #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
  502. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
  503.  
  504. // Enable this feature if all enabled endstop pins are interrupt-capable.
  505. // This will remove the need to poll the interrupt pins, saving many CPU cycles.
  506. //#define ENDSTOP_INTERRUPTS_FEATURE
  507.  
  508. //=============================================================================
  509. //============================== Movement Settings ============================
  510. //=============================================================================
  511. // @section motion
  512.  
  513. /**
  514.  * Default Settings
  515.  *
  516.  * These settings can be reset by M502
  517.  *
  518.  * Note that if EEPROM is enabled, saved values will override these.
  519.  */
  520.  
  521. /**
  522.  * With this option each E stepper can have its own factors for the
  523.  * following movement settings. If fewer factors are given than the
  524.  * total number of extruders, the last value applies to the rest.
  525.  */
  526. //#define DISTINCT_E_FACTORS
  527.  
  528. /**
  529.  * Default Axis Steps Per Unit (steps/mm)
  530.  * Override with M92
  531.  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  532.  */
  533. #define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 2560, 93 }
  534.  
  535. /**
  536.  * Default Max Feed Rate (mm/s)
  537.  * Override with M203
  538.  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  539.  */
  540. #define DEFAULT_MAX_FEEDRATE          { 400, 400, 2, 45 }
  541.  
  542. /**
  543.  * Default Max Acceleration (change/s) change = mm/s
  544.  * (Maximum start speed for accelerated moves)
  545.  * Override with M201
  546.  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  547.  */
  548. #define DEFAULT_MAX_ACCELERATION      { 5000, 5000, 50, 5000 }
  549.  
  550. /**
  551.  * Default Acceleration (change/s) change = mm/s
  552.  * Override with M204
  553.  *
  554.  *   M204 P    Acceleration
  555.  *   M204 R    Retract Acceleration
  556.  *   M204 T    Travel Acceleration
  557.  */
  558. #define DEFAULT_ACCELERATION          1000    // X, Y, Z and E acceleration for printing moves
  559. #define DEFAULT_RETRACT_ACCELERATION  2000    // E acceleration for retracts
  560. #define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration for travel (non printing) moves
  561.  
  562. /**
  563.  * Default Jerk (mm/s)
  564.  * Override with M205 X Y Z E
  565.  *
  566.  * "Jerk" specifies the minimum speed change that requires acceleration.
  567.  * When changing speed and direction, if the difference is less than the
  568.  * value set here, it may happen instantaneously.
  569.  */
  570. #define DEFAULT_XJERK                 20.0
  571. #define DEFAULT_YJERK                 20.0
  572. #define DEFAULT_ZJERK                  0.4
  573. #define DEFAULT_EJERK                  5.0
  574.  
  575. //===========================================================================
  576. //============================= Z Probe Options =============================
  577. //===========================================================================
  578. // @section probes
  579.  
  580. //
  581. // See http://marlinfw.org/docs/configuration/probes.html
  582. //
  583.  
  584. /**
  585.  * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  586.  *
  587.  * Enable this option for a probe connected to the Z Min endstop pin.
  588.  */
  589. #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
  590.  
  591. /**
  592.  * Z_MIN_PROBE_ENDSTOP
  593.  *
  594.  * Enable this option for a probe connected to any pin except Z-Min.
  595.  * (By default Marlin assumes the Z-Max endstop pin.)
  596.  * To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
  597.  *
  598.  *  - The simplest option is to use a free endstop connector.
  599.  *  - Use 5V for powered (usually inductive) sensors.
  600.  *
  601.  *  - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
  602.  *    - For simple switches connect...
  603.  *      - normally-closed switches to GND and D32.
  604.  *      - normally-open switches to 5V and D32.
  605.  *
  606.  * WARNING: Setting the wrong pin may have unexpected and potentially
  607.  * disastrous consequences. Use with caution and do your homework.
  608.  *
  609.  */
  610. //#define Z_MIN_PROBE_ENDSTOP
  611.  
  612. /**
  613.  * Probe Type
  614.  *
  615.  * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
  616.  * Activate one of these to use Auto Bed Leveling below.
  617.  */
  618.  
  619. /**
  620.  * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
  621.  * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  622.  * or (with LCD_BED_LEVELING) the LCD controller.
  623.  */
  624. //#define PROBE_MANUALLY
  625.  
  626. /**
  627.  * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  628.  *   (e.g., an inductive probe or a nozzle-based probe-switch.)
  629.  */
  630. //#define FIX_MOUNTED_PROBE
  631.  
  632. /**
  633.  * Z Servo Probe, such as an endstop switch on a rotating arm.
  634.  */
  635. //#define Z_ENDSTOP_SERVO_NR 0   // Defaults to SERVO 0 connector.
  636. //#define Z_SERVO_ANGLES {70,0}  // Z Servo Deploy and Stow angles
  637.  
  638. /**
  639.  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  640.  */
  641. //#define BLTOUCH
  642. #if ENABLED(BLTOUCH)
  643.   #define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
  644. #endif
  645.  
  646. /**
  647.  * Enable one or more of the following if probing seems unreliable.
  648.  * Heaters and/or fans can be disabled during probing to minimize electrical
  649.  * noise. A delay can also be added to allow noise and vibration to settle.
  650.  * These options are most useful for the BLTouch probe, but may also improve
  651.  * readings with inductive probes and piezo sensors.
  652.  */
  653. //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
  654. //#define PROBING_FANS_OFF          // Turn fans off when probing
  655. //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
  656.  
  657. // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
  658. //#define SOLENOID_PROBE
  659.  
  660. // A sled-mounted probe like those designed by Charles Bell.
  661. //#define Z_PROBE_SLED
  662. //#define SLED_DOCKING_OFFSET 5  // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  663.  
  664. //
  665. // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
  666. //
  667.  
  668. /**
  669.  *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  670.  *   X and Y offsets must be integers.
  671.  *
  672.  *   In the following example the X and Y offsets are both positive:
  673.  *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
  674.  *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
  675.  *
  676.  *      +-- BACK ---+
  677.  *      |           |
  678.  *    L |    (+) P  | R <-- probe (20,20)
  679.  *    E |           | I
  680.  *    F | (-) N (+) | G <-- nozzle (10,10)
  681.  *    T |           | H
  682.  *      |    (-)    | T
  683.  *      |           |
  684.  *      O-- FRONT --+
  685.  *    (0,0)
  686.  */
  687. #define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
  688. #define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]
  689. #define Z_PROBE_OFFSET_FROM_EXTRUDER 0   // Z offset: -below +above  [the nozzle]
  690.  
  691. // X and Y axis travel speed (mm/m) between probes
  692. #define XY_PROBE_SPEED 8000
  693.  
  694. // Speed for the first approach when double-probing (MULTIPLE_PROBING == 2)
  695. #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
  696.  
  697. // Speed for the "accurate" probe of each point
  698. #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
  699.  
  700. // The number of probes to perform at each point.
  701. //   Set to 2 for a fast/slow probe, using the second probe result.
  702. //   Set to 3 or more for slow probes, averaging the results.
  703. //#define MULTIPLE_PROBING 3
  704.  
  705. /**
  706.  * Z probes require clearance when deploying, stowing, and moving between
  707.  * probe points to avoid hitting the bed and other hardware.
  708.  * Servo-mounted probes require extra space for the arm to rotate.
  709.  * Inductive probes need space to keep from triggering early.
  710.  *
  711.  * Use these settings to specify the distance (mm) to raise the probe (or
  712.  * lower the bed). The values set here apply over and above any (negative)
  713.  * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
  714.  * Only integer values >= 1 are valid here.
  715.  *
  716.  * Example: `M851 Z-5` with a CLEARANCE of 4  =>  9mm from bed to nozzle.
  717.  *     But: `M851 Z+1` with a CLEARANCE of 2  =>  2mm from bed to nozzle.
  718.  */
  719. #define Z_CLEARANCE_DEPLOY_PROBE   10 // Z Clearance for Deploy/Stow
  720. #define Z_CLEARANCE_BETWEEN_PROBES  5 // Z Clearance between probe points
  721.  
  722. // For M851 give a range for adjusting the Z probe offset
  723. #define Z_PROBE_OFFSET_RANGE_MIN -20
  724. #define Z_PROBE_OFFSET_RANGE_MAX 20
  725.  
  726. // Enable the M48 repeatability test to test probe accuracy
  727. //#define Z_MIN_PROBE_REPEATABILITY_TEST
  728.  
  729. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  730. // :{ 0:'Low', 1:'High' }
  731. #define X_ENABLE_ON 0
  732. #define Y_ENABLE_ON 0
  733. #define Z_ENABLE_ON 0
  734. #define E_ENABLE_ON 0 // For all extruders
  735.  
  736. // Disables axis stepper immediately when it's not being used.
  737. // WARNING: When motors turn off there is a chance of losing position accuracy!
  738. #define DISABLE_X false
  739. #define DISABLE_Y false
  740. #define DISABLE_Z false
  741. // Warn on display about possibly reduced accuracy
  742. //#define DISABLE_REDUCED_ACCURACY_WARNING
  743.  
  744. // @section extruder
  745.  
  746. #define DISABLE_E false // For all extruders
  747. #define DISABLE_INACTIVE_EXTRUDER true // Keep only the active extruder enabled.
  748.  
  749. // @section machine
  750.  
  751. // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
  752. #define INVERT_X_DIR true
  753. #define INVERT_Y_DIR true
  754. #define INVERT_Z_DIR false
  755.  
  756. // Enable this option for Toshiba stepper drivers
  757. //#define CONFIG_STEPPERS_TOSHIBA
  758.  
  759. // @section extruder
  760.  
  761. // For direct drive extruder v9 set to true, for geared extruder set to false.
  762. #define INVERT_E0_DIR true
  763. #define INVERT_E1_DIR false
  764. #define INVERT_E2_DIR false
  765. #define INVERT_E3_DIR false
  766. #define INVERT_E4_DIR false
  767.  
  768. // @section homing
  769.  
  770. //#define NO_MOTION_BEFORE_HOMING  // Inhibit movement until all axes have been homed
  771.  
  772. //#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
  773.                              // Be sure you have this distance over your Z_MAX_POS in case.
  774.  
  775. // Direction of endstops when homing; 1=MAX, -1=MIN
  776. // :[-1,1]
  777. #define X_HOME_DIR -1
  778. #define Y_HOME_DIR -1
  779. #define Z_HOME_DIR -1
  780.  
  781. // @section machine
  782.  
  783. // The size of the print bed
  784. #define X_BED_SIZE 200
  785. #define Y_BED_SIZE 200
  786.  
  787. // Travel limits (mm) after homing, corresponding to endstop positions.
  788. #define X_MIN_POS 0
  789. #define Y_MIN_POS 0
  790. #define Z_MIN_POS 0
  791. #define X_MAX_POS X_BED_SIZE
  792. #define Y_MAX_POS Y_BED_SIZE
  793. #define Z_MAX_POS 180
  794.  
  795. /**
  796.  * Software Endstops
  797.  *
  798.  * - Prevent moves outside the set machine bounds.
  799.  * - Individual axes can be disabled, if desired.
  800.  * - X and Y only apply to Cartesian robots.
  801.  * - Use 'M211' to set software endstops on/off or report current state
  802.  */
  803.  
  804. // Min software endstops curtail movement below minimum coordinate bounds
  805. #define MIN_SOFTWARE_ENDSTOPS
  806. #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
  807.   #define MIN_SOFTWARE_ENDSTOP_X
  808.   #define MIN_SOFTWARE_ENDSTOP_Y
  809.   #define MIN_SOFTWARE_ENDSTOP_Z
  810. #endif
  811.  
  812. // Max software endstops curtail movement above maximum coordinate bounds
  813. #define MAX_SOFTWARE_ENDSTOPS
  814. #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
  815.   #define MAX_SOFTWARE_ENDSTOP_X
  816.   #define MAX_SOFTWARE_ENDSTOP_Y
  817.   #define MAX_SOFTWARE_ENDSTOP_Z
  818. #endif
  819.  
  820. /**
  821.  * Filament Runout Sensor
  822.  * A mechanical or opto endstop is used to check for the presence of filament.
  823.  *
  824.  * RAMPS-based boards use SERVO3_PIN.
  825.  * For other boards you may need to define FIL_RUNOUT_PIN.
  826.  * By default the firmware assumes HIGH = has filament, LOW = ran out
  827.  */
  828. //#define FILAMENT_RUNOUT_SENSOR
  829. #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  830.   #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
  831.   #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
  832.   #define FILAMENT_RUNOUT_SCRIPT "M600"
  833. #endif
  834.  
  835. //===========================================================================
  836. //=============================== Bed Leveling ==============================
  837. //===========================================================================
  838. // @section calibrate
  839.  
  840. /**
  841.  * Choose one of the options below to enable G29 Bed Leveling. The parameters
  842.  * and behavior of G29 will change depending on your selection.
  843.  *
  844.  *  If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
  845.  *
  846.  * - AUTO_BED_LEVELING_3POINT
  847.  *   Probe 3 arbitrary points on the bed (that aren't collinear)
  848.  *   You specify the XY coordinates of all 3 points.
  849.  *   The result is a single tilted plane. Best for a flat bed.
  850.  *
  851.  * - AUTO_BED_LEVELING_LINEAR
  852.  *   Probe several points in a grid.
  853.  *   You specify the rectangle and the density of sample points.
  854.  *   The result is a single tilted plane. Best for a flat bed.
  855.  *
  856.  * - AUTO_BED_LEVELING_BILINEAR
  857.  *   Probe several points in a grid.
  858.  *   You specify the rectangle and the density of sample points.
  859.  *   The result is a mesh, best for large or uneven beds.
  860.  *
  861.  * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
  862.  *   A comprehensive bed leveling system combining the features and benefits
  863.  *   of other systems. UBL also includes integrated Mesh Generation, Mesh
  864.  *   Validation and Mesh Editing systems.
  865.  *
  866.  * - MESH_BED_LEVELING
  867.  *   Probe a grid manually
  868.  *   The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
  869.  *   For machines without a probe, Mesh Bed Leveling provides a method to perform
  870.  *   leveling in steps so you can manually adjust the Z height at each grid-point.
  871.  *   With an LCD controller the process is guided step-by-step.
  872.  */
  873. //#define AUTO_BED_LEVELING_3POINT
  874. //#define AUTO_BED_LEVELING_LINEAR
  875. //#define AUTO_BED_LEVELING_BILINEAR
  876. //#define AUTO_BED_LEVELING_UBL
  877. //#define MESH_BED_LEVELING
  878.  
  879. /**
  880.  * Enable detailed logging of G28, G29, M48, etc.
  881.  * Turn on with the command 'M111 S32'.
  882.  * NOTE: Requires a lot of PROGMEM!
  883.  */
  884. //#define DEBUG_LEVELING_FEATURE
  885.  
  886. #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
  887.   // Gradually reduce leveling correction until a set height is reached,
  888.   // at which point movement will be level to the machine's XY plane.
  889.   // The height can be set with M420 Z<height>
  890.   #define ENABLE_LEVELING_FADE_HEIGHT
  891.  
  892.   // For Cartesian machines, instead of dividing moves on mesh boundaries,
  893.   // split up moves into short segments like a Delta. This follows the
  894.   // contours of the bed more closely than edge-to-edge straight moves.
  895.   #define SEGMENT_LEVELED_MOVES
  896.   #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
  897.  
  898.   /**
  899.    * Enable the G26 Mesh Validation Pattern tool.
  900.    */
  901.   #define G26_MESH_VALIDATION   // Enable G26 mesh validation
  902.   #if ENABLED(G26_MESH_VALIDATION)
  903.     #define MESH_TEST_NOZZLE_SIZE     0.3   // (mm) Diameter of primary nozzle.
  904.     #define MESH_TEST_LAYER_HEIGHT    0.2   // (mm) Default layer height for the G26 Mesh Validation Tool.
  905.     #define MESH_TEST_HOTEND_TEMP   205.0   // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
  906.     #define MESH_TEST_BED_TEMP       60.0   // (°C) Default bed temperature for the G26 Mesh Validation Tool.
  907.   #endif
  908.  
  909. #endif
  910.  
  911. #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
  912.  
  913.   // Set the number of grid points per dimension.
  914.   #define GRID_MAX_POINTS_X 3
  915.   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  916.  
  917.   // Set the boundaries for probing (where the probe can reach).
  918.   #define LEFT_PROBE_BED_POSITION 30
  919.   #define RIGHT_PROBE_BED_POSITION 175
  920.   #define FRONT_PROBE_BED_POSITION 10
  921.   #define BACK_PROBE_BED_POSITION 145
  922.  
  923.   // The Z probe minimum outer margin (to validate G29 parameters).
  924.   #define MIN_PROBE_EDGE 10
  925.  
  926.   // Probe along the Y axis, advancing X after each column
  927.   //#define PROBE_Y_FIRST
  928.  
  929.   #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
  930.  
  931.     // Beyond the probed grid, continue the implied tilt?
  932.     // Default is to maintain the height of the nearest edge.
  933.     //#define EXTRAPOLATE_BEYOND_GRID
  934.  
  935.     //
  936.     // Experimental Subdivision of the grid by Catmull-Rom method.
  937.     // Synthesizes intermediate points to produce a more detailed mesh.
  938.     //
  939.     //#define ABL_BILINEAR_SUBDIVISION
  940.     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
  941.       // Number of subdivisions between probe points
  942.       #define BILINEAR_SUBDIVISIONS 3
  943.     #endif
  944.  
  945.   #endif
  946.  
  947. #elif ENABLED(AUTO_BED_LEVELING_3POINT)
  948.  
  949.   // 3 arbitrary points to probe.
  950.   // A simple cross-product is used to estimate the plane of the bed.
  951.   #define ABL_PROBE_PT_1_X 15
  952.   #define ABL_PROBE_PT_1_Y 180
  953.   #define ABL_PROBE_PT_2_X 15
  954.   #define ABL_PROBE_PT_2_Y 20
  955.   #define ABL_PROBE_PT_3_X 170
  956.   #define ABL_PROBE_PT_3_Y 20
  957.  
  958. #elif ENABLED(AUTO_BED_LEVELING_UBL)
  959.  
  960.   //===========================================================================
  961.   //========================= Unified Bed Leveling ============================
  962.   //===========================================================================
  963.  
  964.   //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
  965.  
  966.   #define MESH_INSET 1              // Mesh inset margin on print area
  967.   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
  968.   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  969.  
  970.   #define UBL_PROBE_PT_1_X 39       // Probing points for 3-Point leveling of the mesh
  971.   #define UBL_PROBE_PT_1_Y 180
  972.   #define UBL_PROBE_PT_2_X 39
  973.   #define UBL_PROBE_PT_2_Y 20
  974.   #define UBL_PROBE_PT_3_X 180
  975.   #define UBL_PROBE_PT_3_Y 20
  976.  
  977.   #define UBL_MESH_EDIT_MOVES_Z     // Sophisticated users prefer no movement of nozzle
  978.   #define UBL_SAVE_ACTIVE_ON_M500   // Save the currently active mesh in the current slot on M500
  979.  
  980. #elif ENABLED(MESH_BED_LEVELING)
  981.  
  982.   //===========================================================================
  983.   //=================================== Mesh ==================================
  984.   //===========================================================================
  985.  
  986.   #define MESH_INSET 10          // Mesh inset margin on print area
  987.   #define GRID_MAX_POINTS_X 3    // Don't use more than 7 points per axis, implementation limited.
  988.   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
  989.  
  990.   //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
  991.  
  992. #endif // BED_LEVELING
  993.  
  994. /**
  995.  * Use the LCD controller for bed leveling
  996.  * Requires MESH_BED_LEVELING or PROBE_MANUALLY
  997.  */
  998. //#define LCD_BED_LEVELING
  999.  
  1000. #if ENABLED(LCD_BED_LEVELING)
  1001.   #define MBL_Z_STEP 0.025    // Step size while manually probing Z axis.
  1002.   #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
  1003. #endif
  1004.  
  1005. // Add a menu item to move between bed corners for manual bed adjustment
  1006. //#define LEVEL_BED_CORNERS
  1007.  
  1008. /**
  1009.  * Commands to execute at the end of G29 probing.
  1010.  * Useful to retract or move the Z probe out of the way.
  1011.  */
  1012. //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
  1013.  
  1014.  
  1015. // @section homing
  1016.  
  1017. // The center of the bed is at (X=0, Y=0)
  1018. //#define BED_CENTER_AT_0_0
  1019.  
  1020. // Manually set the home position. Leave these undefined for automatic settings.
  1021. // For DELTA this is the top-center of the Cartesian print volume.
  1022. //#define MANUAL_X_HOME_POS 0
  1023. //#define MANUAL_Y_HOME_POS 0
  1024. //#define MANUAL_Z_HOME_POS 0
  1025.  
  1026. // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
  1027. //
  1028. // With this feature enabled:
  1029. //
  1030. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
  1031. // - If stepper drivers time out, it will need X and Y homing again before Z homing.
  1032. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
  1033. // - Prevent Z homing when the Z probe is outside bed area.
  1034. //
  1035. #define Z_SAFE_HOMING
  1036.  
  1037. #if ENABLED(Z_SAFE_HOMING)
  1038.   #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2)    // X point for Z homing when homing all axes (G28).
  1039.   #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2)    // Y point for Z homing when homing all axes (G28).
  1040. #endif
  1041.  
  1042. // Homing speeds (mm/m)
  1043. #define HOMING_FEEDRATE_XY (50*60)
  1044. #define HOMING_FEEDRATE_Z  (4*60)
  1045.  
  1046. // @section calibrate
  1047.  
  1048. /**
  1049.  * Bed Skew Compensation
  1050.  *
  1051.  * This feature corrects for misalignment in the XYZ axes.
  1052.  *
  1053.  * Take the following steps to get the bed skew in the XY plane:
  1054.  *  1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
  1055.  *  2. For XY_DIAG_AC measure the diagonal A to C
  1056.  *  3. For XY_DIAG_BD measure the diagonal B to D
  1057.  *  4. For XY_SIDE_AD measure the edge A to D
  1058.  *
  1059.  * Marlin automatically computes skew factors from these measurements.
  1060.  * Skew factors may also be computed and set manually:
  1061.  *
  1062.  *  - Compute AB     : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
  1063.  *  - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
  1064.  *
  1065.  * If desired, follow the same procedure for XZ and YZ.
  1066.  * Use these diagrams for reference:
  1067.  *
  1068.  *    Y                     Z                     Z
  1069.  *    ^     B-------C       ^     B-------C       ^     B-------C
  1070.  *    |    /       /        |    /       /        |    /       /
  1071.  *    |   /       /         |   /       /         |   /       /
  1072.  *    |  A-------D          |  A-------D          |  A-------D
  1073.  *    +-------------->X     +-------------->X     +-------------->Y
  1074.  *     XY_SKEW_FACTOR        XZ_SKEW_FACTOR        YZ_SKEW_FACTOR
  1075.  */
  1076. //#define SKEW_CORRECTION
  1077.  
  1078. #if ENABLED(SKEW_CORRECTION)
  1079.   // Input all length measurements here:
  1080.   #define XY_DIAG_AC 282.8427124746
  1081.   #define XY_DIAG_BD 282.8427124746
  1082.   #define XY_SIDE_AD 200
  1083.  
  1084.   // Or, set the default skew factors directly here
  1085.   // to override the above measurements:
  1086.   #define XY_SKEW_FACTOR 0.0
  1087.  
  1088.   //#define SKEW_CORRECTION_FOR_Z
  1089.   #if ENABLED(SKEW_CORRECTION_FOR_Z)
  1090.     #define XZ_DIAG_AC 282.8427124746
  1091.     #define XZ_DIAG_BD 282.8427124746
  1092.     #define YZ_DIAG_AC 282.8427124746
  1093.     #define YZ_DIAG_BD 282.8427124746
  1094.     #define YZ_SIDE_AD 200
  1095.     #define XZ_SKEW_FACTOR 0.0
  1096.     #define YZ_SKEW_FACTOR 0.0
  1097.   #endif
  1098.  
  1099.   // Enable this option for M852 to set skew at runtime
  1100.   //#define SKEW_CORRECTION_GCODE
  1101. #endif
  1102.  
  1103. //=============================================================================
  1104. //============================= Additional Features ===========================
  1105. //=============================================================================
  1106.  
  1107. // @section extras
  1108.  
  1109. //
  1110. // EEPROM
  1111. //
  1112. // The microcontroller can store settings in the EEPROM, e.g. max velocity...
  1113. // M500 - stores parameters in EEPROM
  1114. // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
  1115. // M502 - reverts to the default "factory settings".  You still need to store them in EEPROM afterwards if you want to.
  1116. //
  1117. #define EEPROM_SETTINGS // Enable for M500 and M501 commands
  1118. //#define DISABLE_M503    // Saves ~2700 bytes of PROGMEM. Disable for release!
  1119. #define EEPROM_CHITCHAT   // Give feedback on EEPROM commands. Disable to save PROGMEM.
  1120.  
  1121. //
  1122. // Host Keepalive
  1123. //
  1124. // When enabled Marlin will send a busy status message to the host
  1125. // every couple of seconds when it can't accept commands.
  1126. //
  1127. #define HOST_KEEPALIVE_FEATURE        // Disable this if your host doesn't like keepalive messages
  1128. #define DEFAULT_KEEPALIVE_INTERVAL 4  // Number of seconds between "busy" messages. Set with M113.
  1129. #define BUSY_WHILE_HEATING            // Some hosts require "busy" messages even during heating
  1130.  
  1131. //
  1132. // M100 Free Memory Watcher
  1133. //
  1134. //#define M100_FREE_MEMORY_WATCHER    // Add M100 (Free Memory Watcher) to debug memory usage
  1135.  
  1136. //
  1137. // G20/G21 Inch mode support
  1138. //
  1139. //#define INCH_MODE_SUPPORT
  1140.  
  1141. //
  1142. // M149 Set temperature units support
  1143. //
  1144. //#define TEMPERATURE_UNITS_SUPPORT
  1145.  
  1146. // @section temperature
  1147.  
  1148. // Preheat Constants
  1149. #define PREHEAT_1_TEMP_HOTEND 180
  1150. #define PREHEAT_1_TEMP_BED     70
  1151. #define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
  1152.  
  1153. #define PREHEAT_2_TEMP_HOTEND 240
  1154. #define PREHEAT_2_TEMP_BED    110
  1155. #define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
  1156.  
  1157. /**
  1158.  * Nozzle Park
  1159.  *
  1160.  * Park the nozzle at the given XYZ position on idle or G27.
  1161.  *
  1162.  * The "P" parameter controls the action applied to the Z axis:
  1163.  *
  1164.  *    P0  (Default) If Z is below park Z raise the nozzle.
  1165.  *    P1  Raise the nozzle always to Z-park height.
  1166.  *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  1167.  */
  1168. //#define NOZZLE_PARK_FEATURE
  1169.  
  1170. #if ENABLED(NOZZLE_PARK_FEATURE)
  1171.   // Specify a park position as { X, Y, Z }
  1172.   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
  1173.   #define NOZZLE_PARK_XY_FEEDRATE 100   // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
  1174.   #define NOZZLE_PARK_Z_FEEDRATE 5      // Z axis feedrate in mm/s (not used for delta printers)
  1175. #endif
  1176.  
  1177. /**
  1178.  * Clean Nozzle Feature -- EXPERIMENTAL
  1179.  *
  1180.  * Adds the G12 command to perform a nozzle cleaning process.
  1181.  *
  1182.  * Parameters:
  1183.  *   P  Pattern
  1184.  *   S  Strokes / Repetitions
  1185.  *   T  Triangles (P1 only)
  1186.  *
  1187.  * Patterns:
  1188.  *   P0  Straight line (default). This process requires a sponge type material
  1189.  *       at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  1190.  *       between the start / end points.
  1191.  *
  1192.  *   P1  Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
  1193.  *       number of zig-zag triangles to do. "S" defines the number of strokes.
  1194.  *       Zig-zags are done in whichever is the narrower dimension.
  1195.  *       For example, "G12 P1 S1 T3" will execute:
  1196.  *
  1197.  *          --
  1198.  *         |  (X0, Y1) |     /\        /\        /\     | (X1, Y1)
  1199.  *         |           |    /  \      /  \      /  \    |
  1200.  *       A |           |   /    \    /    \    /    \   |
  1201.  *         |           |  /      \  /      \  /      \  |
  1202.  *         |  (X0, Y0) | /        \/        \/        \ | (X1, Y0)
  1203.  *          --         +--------------------------------+
  1204.  *                       |________|_________|_________|
  1205.  *                           T1        T2        T3
  1206.  *
  1207.  *   P2  Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
  1208.  *       "R" specifies the radius. "S" specifies the stroke count.
  1209.  *       Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  1210.  *
  1211.  *   Caveats: The ending Z should be the same as starting Z.
  1212.  * Attention: EXPERIMENTAL. G-code arguments may change.
  1213.  *
  1214.  */
  1215. //#define NOZZLE_CLEAN_FEATURE
  1216.  
  1217. #if ENABLED(NOZZLE_CLEAN_FEATURE)
  1218.   // Default number of pattern repetitions
  1219.   #define NOZZLE_CLEAN_STROKES  12
  1220.  
  1221.   // Default number of triangles
  1222.   #define NOZZLE_CLEAN_TRIANGLES  3
  1223.  
  1224.   // Specify positions as { X, Y, Z }
  1225.   #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
  1226.   #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}
  1227.  
  1228.   // Circular pattern radius
  1229.   #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
  1230.   // Circular pattern circle fragments number
  1231.   #define NOZZLE_CLEAN_CIRCLE_FN 10
  1232.   // Middle point of circle
  1233.   #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
  1234.  
  1235.   // Moves the nozzle to the initial position
  1236.   #define NOZZLE_CLEAN_GOBACK
  1237. #endif
  1238.  
  1239. /**
  1240.  * Print Job Timer
  1241.  *
  1242.  * Automatically start and stop the print job timer on M104/M109/M190.
  1243.  *
  1244.  *   M104 (hotend, no wait) - high temp = none,        low temp = stop timer
  1245.  *   M109 (hotend, wait)    - high temp = start timer, low temp = stop timer
  1246.  *   M190 (bed, wait)       - high temp = start timer, low temp = none
  1247.  *
  1248.  * The timer can also be controlled with the following commands:
  1249.  *
  1250.  *   M75 - Start the print job timer
  1251.  *   M76 - Pause the print job timer
  1252.  *   M77 - Stop the print job timer
  1253.  */
  1254. #define PRINTJOB_TIMER_AUTOSTART
  1255.  
  1256. /**
  1257.  * Print Counter
  1258.  *
  1259.  * Track statistical data such as:
  1260.  *
  1261.  *  - Total print jobs
  1262.  *  - Total successful print jobs
  1263.  *  - Total failed print jobs
  1264.  *  - Total time printing
  1265.  *
  1266.  * View the current statistics with M78.
  1267.  */
  1268. //#define PRINTCOUNTER
  1269.  
  1270. //=============================================================================
  1271. //============================= LCD and SD support ============================
  1272. //=============================================================================
  1273.  
  1274. // @section lcd
  1275.  
  1276. /**
  1277.  * LCD LANGUAGE
  1278.  *
  1279.  * Select the language to display on the LCD. These languages are available:
  1280.  *
  1281.  *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, eu, fi, fr, fr_utf8, gl,
  1282.  *    hr, it, kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8,
  1283.  *    tr, uk, zh_CN, zh_TW, test
  1284.  *
  1285.  * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', test':'TEST' }
  1286.  */
  1287. #define LCD_LANGUAGE en
  1288.  
  1289. /**
  1290.  * LCD Character Set
  1291.  *
  1292.  * Note: This option is NOT applicable to Graphical Displays.
  1293.  *
  1294.  * All character-based LCDs provide ASCII plus one of these
  1295.  * language extensions:
  1296.  *
  1297.  *  - JAPANESE ... the most common
  1298.  *  - WESTERN  ... with more accented characters
  1299.  *  - CYRILLIC ... for the Russian language
  1300.  *
  1301.  * To determine the language extension installed on your controller:
  1302.  *
  1303.  *  - Compile and upload with LCD_LANGUAGE set to 'test'
  1304.  *  - Click the controller to view the LCD menu
  1305.  *  - The LCD will display Japanese, Western, or Cyrillic text
  1306.  *
  1307.  * See http://marlinfw.org/docs/development/lcd_language.html
  1308.  *
  1309.  * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  1310.  */
  1311. #define DISPLAY_CHARSET_HD44780 JAPANESE
  1312.  
  1313. /**
  1314.  * LCD TYPE
  1315.  *
  1316.  * Enable ULTRA_LCD for a 16x2, 16x4, 20x2, or 20x4 character-based LCD.
  1317.  * Enable DOGLCD for a 128x64 (ST7565R) Full Graphical Display.
  1318.  * (These options will be enabled automatically for most displays.)
  1319.  *
  1320.  * IMPORTANT: The U8glib library is required for Full Graphic Display!
  1321.  *            https://github.com/olikraus/U8glib_Arduino
  1322.  */
  1323. //#define ULTRA_LCD   // Character based
  1324. //#define DOGLCD      // Full graphics display
  1325.  
  1326. /**
  1327.  * SD CARD
  1328.  *
  1329.  * SD Card support is disabled by default. If your controller has an SD slot,
  1330.  * you must uncomment the following option or it won't work.
  1331.  *
  1332.  */
  1333. #define SDSUPPORT
  1334.  
  1335. /**
  1336.  * SD CARD: SPI SPEED
  1337.  *
  1338.  * Enable one of the following items for a slower SPI transfer speed.
  1339.  * This may be required to resolve "volume init" errors.
  1340.  */
  1341. //#define SPI_SPEED SPI_HALF_SPEED
  1342. //#define SPI_SPEED SPI_QUARTER_SPEED
  1343. //#define SPI_SPEED SPI_EIGHTH_SPEED
  1344.  
  1345. /**
  1346.  * SD CARD: ENABLE CRC
  1347.  *
  1348.  * Use CRC checks and retries on the SD communication.
  1349.  */
  1350. //#define SD_CHECK_AND_RETRY
  1351.  
  1352. //
  1353. // ENCODER SETTINGS
  1354. //
  1355. // This option overrides the default number of encoder pulses needed to
  1356. // produce one step. Should be increased for high-resolution encoders.
  1357. //
  1358. //#define ENCODER_PULSES_PER_STEP 1
  1359.  
  1360. //
  1361. // Use this option to override the number of step signals required to
  1362. // move between next/prev menu items.
  1363. //
  1364. //#define ENCODER_STEPS_PER_MENU_ITEM 5
  1365.  
  1366. /**
  1367.  * Encoder Direction Options
  1368.  *
  1369.  * Test your encoder's behavior first with both options disabled.
  1370.  *
  1371.  *  Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
  1372.  *  Reversed Menu Navigation only?    Enable REVERSE_MENU_DIRECTION.
  1373.  *  Reversed Value Editing only?      Enable BOTH options.
  1374.  */
  1375.  
  1376. //
  1377. // This option reverses the encoder direction everywhere.
  1378. //
  1379. //  Set this option if CLOCKWISE causes values to DECREASE
  1380. //
  1381. #define REVERSE_ENCODER_DIRECTION
  1382.  
  1383. //
  1384. // This option reverses the encoder direction for navigating LCD menus.
  1385. //
  1386. //  If CLOCKWISE normally moves DOWN this makes it go UP.
  1387. //  If CLOCKWISE normally moves UP this makes it go DOWN.
  1388. //
  1389. //#define REVERSE_MENU_DIRECTION
  1390.  
  1391. //
  1392. // Individual Axis Homing
  1393. //
  1394. // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
  1395. //
  1396. //#define INDIVIDUAL_AXIS_HOMING_MENU
  1397.  
  1398. //
  1399. // SPEAKER/BUZZER
  1400. //
  1401. // If you have a speaker that can produce tones, enable it here.
  1402. // By default Marlin assumes you have a buzzer with a fixed frequency.
  1403. //
  1404. //#define SPEAKER
  1405.  
  1406. //
  1407. // The duration and frequency for the UI feedback sound.
  1408. // Set these to 0 to disable audio feedback in the LCD menus.
  1409. //
  1410. // Note: Test audio output with the G-Code:
  1411. //  M300 S<frequency Hz> P<duration ms>
  1412. //
  1413. //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
  1414. //#define LCD_FEEDBACK_FREQUENCY_HZ 1000
  1415.  
  1416. //
  1417. // CONTROLLER TYPE: Standard
  1418. //
  1419. // Marlin supports a wide variety of controllers.
  1420. // Enable one of the following options to specify your controller.
  1421. //
  1422.  
  1423. //
  1424. // ULTIMAKER Controller.
  1425. //
  1426. //#define ULTIMAKERCONTROLLER
  1427.  
  1428. //
  1429. // ULTIPANEL as seen on Thingiverse.
  1430. //
  1431. //#define ULTIPANEL
  1432.  
  1433. //
  1434. // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
  1435. // http://reprap.org/wiki/PanelOne
  1436. //
  1437. //#define PANEL_ONE
  1438.  
  1439. //
  1440. // MaKr3d Makr-Panel with graphic controller and SD support.
  1441. // http://reprap.org/wiki/MaKr3d_MaKrPanel
  1442. //
  1443. //#define MAKRPANEL
  1444.  
  1445. //
  1446. // ReprapWorld Graphical LCD
  1447. // https://reprapworld.com/?products_details&products_id/1218
  1448. //
  1449. //#define REPRAPWORLD_GRAPHICAL_LCD
  1450.  
  1451. //
  1452. // Activate one of these if you have a Panucatt Devices
  1453. // Viki 2.0 or mini Viki with Graphic LCD
  1454. // http://panucatt.com
  1455. //
  1456. //#define VIKI2
  1457. //#define miniVIKI
  1458.  
  1459. //
  1460. // Adafruit ST7565 Full Graphic Controller.
  1461. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
  1462. //
  1463. //#define ELB_FULL_GRAPHIC_CONTROLLER
  1464.  
  1465. //
  1466. // RepRapDiscount Smart Controller.
  1467. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  1468. //
  1469. // Note: Usually sold with a white PCB.
  1470. //
  1471. #define REPRAP_DISCOUNT_SMART_CONTROLLER
  1472.  
  1473. //
  1474. // GADGETS3D G3D LCD/SD Controller
  1475. // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
  1476. //
  1477. // Note: Usually sold with a blue PCB.
  1478. //
  1479. //#define G3D_PANEL
  1480.  
  1481. //
  1482. // RepRapDiscount FULL GRAPHIC Smart Controller
  1483. // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
  1484. //
  1485. //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
  1486.  
  1487. //
  1488. // MakerLab Mini Panel with graphic
  1489. // controller and SD support - http://reprap.org/wiki/Mini_panel
  1490. //
  1491. //#define MINIPANEL
  1492.  
  1493. //
  1494. // RepRapWorld REPRAPWORLD_KEYPAD v1.1
  1495. // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
  1496. //
  1497. // REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
  1498. // is pressed, a value of 10.0 means 10mm per click.
  1499. //
  1500. //#define REPRAPWORLD_KEYPAD
  1501. //#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0
  1502.  
  1503. //
  1504. // RigidBot Panel V1.0
  1505. // http://www.inventapart.com/
  1506. //
  1507. //#define RIGIDBOT_PANEL
  1508.  
  1509. //
  1510. // BQ LCD Smart Controller shipped by
  1511. // default with the BQ Hephestos 2 and Witbox 2.
  1512. //
  1513. //#define BQ_LCD_SMART_CONTROLLER
  1514.  
  1515. //
  1516. // Cartesio UI
  1517. // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
  1518. //
  1519. //#define CARTESIO_UI
  1520.  
  1521. //
  1522. // ANET and Tronxy Controller supported displays.
  1523. //
  1524. //#define ZONESTAR_LCD            // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
  1525.                                   // This LCD is known to be susceptible to electrical interference
  1526.                                   // which scrambles the display.  Pressing any button clears it up.
  1527.                                   // This is a LCD2004 display with 5 analog buttons.
  1528.  
  1529. //#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
  1530.                                   // A clone of the RepRapDiscount full graphics display but with
  1531.                                   // different pins/wiring (see pins_ANET_10.h).
  1532.  
  1533. //
  1534. // LCD for Melzi Card with Graphical LCD
  1535. //
  1536. //#define LCD_FOR_MELZI
  1537.  
  1538. //
  1539. // CONTROLLER TYPE: I2C
  1540. //
  1541. // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
  1542. // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
  1543. //
  1544.  
  1545. //
  1546. // Elefu RA Board Control Panel
  1547. // http://www.elefu.com/index.php?route=product/product&product_id=53
  1548. //
  1549. //#define RA_CONTROL_PANEL
  1550.  
  1551. //
  1552. // Sainsmart YW Robot (LCM1602) LCD Display
  1553. //
  1554. // Note: This controller requires F.Malpartida's LiquidCrystal_I2C library
  1555. // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
  1556. //
  1557. //#define LCD_I2C_SAINSMART_YWROBOT
  1558.  
  1559. //
  1560. // Generic LCM1602 LCD adapter
  1561. //
  1562. //#define LCM1602
  1563.  
  1564. //
  1565. // PANELOLU2 LCD with status LEDs,
  1566. // separate encoder and click inputs.
  1567. //
  1568. // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
  1569. // For more info: https://github.com/lincomatic/LiquidTWI2
  1570. //
  1571. // Note: The PANELOLU2 encoder click input can either be directly connected to
  1572. // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
  1573. //
  1574. //#define LCD_I2C_PANELOLU2
  1575.  
  1576. //
  1577. // Panucatt VIKI LCD with status LEDs,
  1578. // integrated click & L/R/U/D buttons, separate encoder inputs.
  1579. //
  1580. //#define LCD_I2C_VIKI
  1581.  
  1582. //
  1583. // SSD1306 OLED full graphics generic display
  1584. //
  1585. //#define U8GLIB_SSD1306
  1586.  
  1587. //
  1588. // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
  1589. //
  1590. //#define SAV_3DGLCD
  1591. #if ENABLED(SAV_3DGLCD)
  1592.   //#define U8GLIB_SSD1306
  1593.   #define U8GLIB_SH1106
  1594. #endif
  1595.  
  1596. //
  1597. // CONTROLLER TYPE: Shift register panels
  1598. //
  1599. // 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
  1600. // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
  1601. //
  1602. //#define SAV_3DLCD
  1603.  
  1604. //
  1605. // TinyBoy2 128x64 OLED / Encoder Panel
  1606. //
  1607. //#define OLED_PANEL_TINYBOY2
  1608.  
  1609. //
  1610. // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
  1611. // https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
  1612. //
  1613. //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
  1614.  
  1615. //
  1616. // MKS MINI12864 with graphic controller and SD support
  1617. // http://reprap.org/wiki/MKS_MINI_12864
  1618. //
  1619. //#define MKS_MINI_12864
  1620.  
  1621. //
  1622. // Factory display for Creality CR-10
  1623. // https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
  1624. //
  1625. // This is RAMPS-compatible using a single 10-pin connector.
  1626. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
  1627. //
  1628. //#define CR10_STOCKDISPLAY
  1629.  
  1630. //
  1631. // MKS OLED 1.3" 128x64 FULL GRAPHICS CONTROLLER
  1632. // http://reprap.org/wiki/MKS_12864OLED
  1633. //
  1634. // Tiny, but very sharp OLED display
  1635. // If there is a pixel shift, try the other controller.
  1636. //
  1637. //#define MKS_12864OLED          // Uses the SH1106 controller (default)
  1638. //#define MKS_12864OLED_SSD1306  // Uses the SSD1306 controller
  1639.  
  1640. // Silvergate GLCD controller
  1641. // http://github.com/android444/Silvergate
  1642. //
  1643. //#define SILVER_GATE_GLCD_CONTROLLER
  1644.  
  1645. //=============================================================================
  1646. //=============================== Extra Features ==============================
  1647. //=============================================================================
  1648.  
  1649. // @section extras
  1650.  
  1651. // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
  1652. //#define FAST_PWM_FAN
  1653.  
  1654. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  1655. // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
  1656. // is too low, you should also increment SOFT_PWM_SCALE.
  1657. //#define FAN_SOFT_PWM
  1658.  
  1659. // Incrementing this by 1 will double the software PWM frequency,
  1660. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  1661. // However, control resolution will be halved for each increment;
  1662. // at zero value, there are 128 effective control positions.
  1663. #define SOFT_PWM_SCALE 0
  1664.  
  1665. // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
  1666. // be used to mitigate the associated resolution loss. If enabled,
  1667. // some of the PWM cycles are stretched so on average the desired
  1668. // duty cycle is attained.
  1669. //#define SOFT_PWM_DITHER
  1670.  
  1671. // Temperature status LEDs that display the hotend and bed temperature.
  1672. // If all hotends, bed temperature, and target temperature are under 54C
  1673. // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
  1674. //#define TEMP_STAT_LEDS
  1675.  
  1676. // M240  Triggers a camera by emulating a Canon RC-1 Remote
  1677. // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  1678. //#define PHOTOGRAPH_PIN     23
  1679.  
  1680. // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
  1681. //#define SF_ARC_FIX
  1682.  
  1683. // Support for the BariCUDA Paste Extruder
  1684. //#define BARICUDA
  1685.  
  1686. // Support for BlinkM/CyzRgb
  1687. //#define BLINKM
  1688.  
  1689. // Support for PCA9632 PWM LED driver
  1690. //#define PCA9632
  1691.  
  1692. /**
  1693.  * RGB LED / LED Strip Control
  1694.  *
  1695.  * Enable support for an RGB LED connected to 5V digital pins, or
  1696.  * an RGB Strip connected to MOSFETs controlled by digital pins.
  1697.  *
  1698.  * Adds the M150 command to set the LED (or LED strip) color.
  1699.  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  1700.  * luminance values can be set from 0 to 255.
  1701.  * For Neopixel LED an overall brightness parameter is also available.
  1702.  *
  1703.  * *** CAUTION ***
  1704.  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  1705.  *  as the Arduino cannot handle the current the LEDs will require.
  1706.  *  Failure to follow this precaution can destroy your Arduino!
  1707.  *  NOTE: A separate 5V power supply is required! The Neopixel LED needs
  1708.  *  more current than the Arduino 5V linear regulator can produce.
  1709.  * *** CAUTION ***
  1710.  *
  1711.  * LED Type. Enable only one of the following two options.
  1712.  *
  1713.  */
  1714. //#define RGB_LED
  1715. //#define RGBW_LED
  1716.  
  1717. #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
  1718.   #define RGB_LED_R_PIN 34
  1719.   #define RGB_LED_G_PIN 43
  1720.   #define RGB_LED_B_PIN 35
  1721.   #define RGB_LED_W_PIN -1
  1722. #endif
  1723.  
  1724. // Support for Adafruit Neopixel LED driver
  1725. //#define NEOPIXEL_LED
  1726. #if ENABLED(NEOPIXEL_LED)
  1727.   #define NEOPIXEL_TYPE   NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  1728.   #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
  1729.   #define NEOPIXEL_PIXELS 30       // Number of LEDs in the strip
  1730.   #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  1731.   #define NEOPIXEL_BRIGHTNESS 127  // Initial brightness (0-255)
  1732.   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
  1733. #endif
  1734.  
  1735. /**
  1736.  * Printer Event LEDs
  1737.  *
  1738.  * During printing, the LEDs will reflect the printer status:
  1739.  *
  1740.  *  - Gradually change from blue to violet as the heated bed gets to target temp
  1741.  *  - Gradually change from violet to red as the hotend gets to temperature
  1742.  *  - Change to white to illuminate work surface
  1743.  *  - Change to green once print has finished
  1744.  *  - Turn off after the print has finished and the user has pushed a button
  1745.  */
  1746. #if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
  1747.   #define PRINTER_EVENT_LEDS
  1748. #endif
  1749.  
  1750. /**
  1751.  * R/C SERVO support
  1752.  * Sponsored by TrinityLabs, Reworked by codexmas
  1753.  */
  1754.  
  1755. /**
  1756.  * Number of servos
  1757.  *
  1758.  * For some servo-related options NUM_SERVOS will be set automatically.
  1759.  * Set this manually if there are extra servos needing manual control.
  1760.  * Leave undefined or set to 0 to entirely disable the servo subsystem.
  1761.  */
  1762. //#define NUM_SERVOS 1 // Servo index starts with 0 for M280 command
  1763.  
  1764. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
  1765. // 300ms is a good value but you can try less delay.
  1766. // If the servo can't reach the requested position, increase it.
  1767. #define SERVO_DELAY { 300 }
  1768.  
  1769. // Servo deactivation
  1770. //
  1771. // With this option servos are powered only during movement, then turned off to prevent jitter.
  1772. //#define DEACTIVATE_SERVOS_AFTER_MOVE
  1773.  
  1774. #endif // CONFIGURATION_H
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!