Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot> bootm
- ## Booting kernel from Legacy Image at 22000000 ...
- Image Name: Linux-3.2.5
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 1609896 Bytes = 1.5 MB
- Load Address: 20008000
- Entry Point: 20008000
- Verifying Checksum ... OK
- Loading Kernel Image ... OK
- OK
- Starting kernel ...
- Uncompressing Linux... done, booting the kernel.
- Linux version 3.2.5 (abu@software-lab) (gcc version 4.4.3 (ctng-1.6.1) ) #3 Sat Feb 11 17:21:46 CET 2012
- CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
- CPU: VIVT data cache, VIVT instruction cache
- Machine: Atmel AT91SAM9G20-EK
- Memory policy: ECC disabled, Data cache writeback
- AT91: Detected soc type: at91sam9g20
- AT91: Detected soc subtype: Unknown
- AT91: sram at 0x200000 of 0x4000 mapped at 0xfef74000
- AT91: sram at 0x300000 of 0x4000 mapped at 0xfef70000
- Clocks: CPU 396 MHz, master 132 MHz, main 18.432 MHz
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- Kernel command line: mem=64M console=ttyS0,115200 root=/dev/mtdblock2 rw rootfstype=jffs2 mtdparts=atmel_nand:1M(bootloader),3M(kernel),-(rootfs)
- PID hash table entries: 256 (order: -2, 1024 bytes)
- Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- Memory: 64MB = 64MB total
- Memory: 61712k/61712k available, 3824k reserved, 0K highmem
- Virtual kernel memory layout:
- vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- vmalloc : 0xc4800000 - 0xfee00000 ( 934 MB)
- lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
- modules : 0xbf000000 - 0xc0000000 ( 16 MB)
- .text : 0xc0008000 - 0xc02cd000 (2836 kB)
- .init : 0xc02cd000 - 0xc02ee000 ( 132 kB)
- .data : 0xc02ee000 - 0xc030f620 ( 134 kB)
- .bss : 0xc030f644 - 0xc0324f7c ( 87 kB)
- NR_IRQS:192
- AT91: 96 gpio irqs in 3 banks
- Console: colour dummy device 80x30
- Calibrating delay loop... 197.01 BogoMIPS (lpj=985088)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 512
- CPU: Testing write buffer coherency: ok
- NET: Registered protocol family 16
- AT91: Power Management
- AT91: Starting after general reset
- bio: create slab <bio-0> at 0
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- Switching to clocksource pit
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 2048 (order: 2, 16384 bytes)
- TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
- TCP: Hash tables configured (established 2048 bind 2048)
- TCP reno registered
- UDP hash table entries: 256 (order: 0, 4096 bytes)
- UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- NET: Registered protocol family 1
- NetWinder Floating Point Emulator V0.97 (double precision)
- JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
- msgmni has been set to 120
- io scheduler noop registered (default)
- atmel_usart.0: ttyS0 at MMIO 0xfffff200 (irq = 1) is a ATMEL_SERIAL
- console [ttyS0] enabled
- atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL
- atmel_usart.2: ttyS2 at MMIO 0xfffb4000 (irq = 7) is a ATMEL_SERIAL
- brd: module loaded
- loop: module loaded
- atmel_nand atmel_nand: No DMA support for NAND access.
- NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
- Scanning device for bad blocks
- Bad eraseblock 113 at 0x000000e20000
- Bad eraseblock 492 at 0x000003d80000
- Bad eraseblock 592 at 0x000004a00000
- Bad eraseblock 755 at 0x000005e60000
- 3 cmdlinepart partitions found on MTD device atmel_nand
- Creating 3 MTD partitions on "atmel_nand":
- 0x000000000000-0x000000100000 : "bootloader"
- 0x000000100000-0x000000400000 : "kernel"
- 0x000000400000-0x000010000000 : "rootfs"
- atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffc8000 (irq 12)
- MACB_mii_bus: probed
- eth0: Atmel MACB at 0xfffc4000 irq 21 (3a:1f:34:08:54:54)
- eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:00, irq=-1)
- ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- at91_ohci at91_ohci: AT91 OHCI
- at91_ohci at91_ohci: new USB bus registered, assigned bus number 1
- at91_ohci at91_ohci: irq 20, io mem 0x00500000
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 2 ports detected
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- mousedev: PS/2 mouse device common for all mice
- rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0
- rtc-at91sam9 at91_rtt.0: rtc0: SET TIME!
- TCP cubic registered
- NET: Registered protocol family 17
- input: gpio-keys as /devices/platform/gpio-keys/input/input0
- rtc-at91sam9 at91_rtt.0: hctosys: unable to read the hardware clock
- VFS: Mounted root (jffs2 filesystem) on device 31:2.
- Freeing init memory: 132K
- Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
- Backtrace:
- [<c0012be0>] (dump_backtrace+0x0/0x10c) from [<c02350e4>] (dump_stack+0x18/0x1c)
- r7:00000013 r6:c0023544 r5:c02edd9c r4:c030f9e8
- [<c02350cc>] (dump_stack+0x0/0x1c) from [<c0235148>] (panic+0x60/0x1a0)
- [<c02350e8>] (panic+0x0/0x1a0) from [<c0008914>] (init_post+0x84/0xd4)
- r3:fffffffe r2:00000002 r1:00000080 r0:c028db10
- [<c0008890>] (init_post+0x0/0xd4) from [<c02cd2f8>] (kernel_init+0xf4/0x124)
- r5:c02edd9c r4:c030f660
- [<c02cd204>] (kernel_init+0x0/0x124) from [<c0023544>] (do_exit+0x0/0x6c8)
Add Comment
Please, Sign In to add comment