Guest User

Untitled

a guest
Feb 8th, 2020
332
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. BL2 Built : 19:22:01, Jul 31 2019. g12b ge9a9000 - zhiguang.ouyang@droid07-sz
  2.  
  3. Board ID = 8
  4. Set A53 clk to 24M
  5. Set A73 clk to 24M
  6. Set clk81 to 24M
  7. A53 clk: 1200 MHz
  8. A73 clk: 1200 MHz
  9. CLK81: 166.6M
  10. smccc: 00019ac8
  11. eMMC boot @ 0
  12. sw8 s
  13. DDR driver_vesion: LPDDR4_PHY_V_0_1_18 build time: Jul 31 2019 19:21:56
  14. board id: 8
  15. Load FIP HDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
  16. fw parse done
  17. Load ddrfw from eMMC, src: 0x00060200, des: 0xfffd0000, size: 0x0000c000, part: 0
  18. Load ddrfw from eMMC, src: 0x00038200, des: 0xfffd0000, size: 0x00004000, part: 0
  19. PIEI prepare done
  20. fastboot data load
  21. 00000000
  22. emmc switch 1 ok
  23. ddr saved addr:00016000
  24. Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
  25. 00000000
  26. emmc switch 0 ok
  27. fastboot data verify
  28. verify result: 265
  29. Cfg max: 4, cur: 1. Board id: 255. Force loop cfg
  30. LPDDR4 probe
  31. ddr clk to 1608MHz
  32. Load ddrfw from eMMC, src: 0x0003c200, des: 0xfffd0000, size: 0x0000c000, part: 0
  33.  
  34. dmc_version 0001
  35. Check phy result
  36. INFO : End of CA training
  37. INFO : End of initialization
  38. INFO : Training has run successfully!
  39. Check phy result
  40. INFO : End of initialization
  41. INFO : End of read enable training
  42. INFO : End of fine write leveling
  43. INFO : End of Write leveling coarse delay
  44. INFO : Training has run successfully!
  45. Check phy result
  46. INFO : End of initialization
  47. INFO : End of read dq deskew training
  48. INFO : End of MPR read delay center optimization
  49. INFO : End of write delay center optimization
  50. INFO : End of read delay center optimization
  51. INFO : End of max read latency training
  52. INFO : Training has run successfully!
  53. 1D training succeed
  54. Load ddrfw from eMMC, src: 0x00048200, des: 0xfffd0000, size: 0x0000c000, part: 0
  55. Check phy result
  56. INFO : End of initialization
  57. INFO : End of 2D read delay Voltage center optimization
  58. INFO : End of 2D read delay Voltage center optimization
  59. INFO : End of 2D write delay Voltage center optimization
  60. INFO : End of 2D write delay Voltage center optimization
  61. INFO : Training has run successfully!
  62.  
  63. channel==0
  64. RxClkDly_Margin_A0==87 ps 9
  65. TxDqDly_Margin_A0==97 ps 10
  66. RxClkDly_Margin_A1==97 ps 10
  67. TxDqDly_Margin_A1==106 ps 11
  68. TrainedVREFDQ_A0==26
  69. TrainedVREFDQ_A1==27
  70. VrefDac_Margin_A0==27
  71. DeviceVref_Margin_A0==26
  72. VrefDac_Margin_A1==28
  73. DeviceVref_Margin_A1==26
  74.  
  75.  
  76. channel==1
  77. RxClkDly_Margin_A0==97 ps 10
  78. TxDqDly_Margin_A0==106 ps 11
  79. RxClkDly_Margin_A1==97 ps 10
  80. TxDqDly_Margin_A1==106 ps 11
  81. TrainedVREFDQ_A0==25
  82. TrainedVREFDQ_A1==26
  83. VrefDac_Margin_A0==29
  84. DeviceVref_Margin_A0==25
  85. VrefDac_Margin_A1==28
  86. DeviceVref_Margin_A1==25
  87.  
  88. dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004
  89.  
  90. soc_vref_reg_value 0x 00000026 00000027 00000028 00000027 00000027 00000026 00000026 00000026 00000027 0000003
  91. 2D training succeed
  92. aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_18 build time: Jul 31 2019 19:22:05
  93. auto size-- 65535DDR cs0 size: 2048MB
  94. DDR cs1 size: 2048MB
  95. DMC_DDR_CTRL: 00e00024DDR size: 3928MB
  96. cs0 DataBus test pass
  97. cs1 DataBus test pass
  98. cs0 AddrBus test pass
  99. cs1 AddrBus test pass
  100.  
  101. 100bdlr_step_size ps== 450
  102. result report
  103. boot times 0Enable ddr reg access
  104. 00000000
  105. emmc switch 3 ok
  106. Authentication key not yet programmed
  107. get rpmb counter error 0x00000007
  108. 00000000
  109. emmc switch 0 ok
  110. Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
  111. Load BL3X from eMMC, src: 0x0006c200, des: 0x0175c000, size: 0x000d6600, part: 0
  112. 0.0;M3 CHK:0;cm4_sp_mode 0
  113. MVN_1=0x00000000
  114. MVN_2=0x00000000
  115. [Image: g12b_v1.1.3386-3b31431 2019-05-21 10:42:10 luan.yuan@droid15-sz]
  116. OPS=0x10
  117. ring efuse init
  118. chipver efuse init
  119. 29 0b 10 00 01 10 20 00 00 01 37 30 4e 42 4e 50
  120. [0.018961 Inits done]
  121. secure task start!
  122. high task start!
  123. low task start!
  124. run into bl31
  125. NOTICE: BL31: v1.3(release):4fc40b1
  126. NOTICE: BL31: Built : 15:58:17, May 22 2019
  127. NOTICE: BL31: G12A normal boot!
  128. NOTICE: BL31: BL33 decompress pass
  129. ERROR: Error initializing runtime service opteed_fast
  130.  
  131.  
  132. U-Boot 2015.01-g5a7732a-dirty (Aug 09 2019 - 14:42:00)
  133.  
  134. DRAM: 3.8 GiB
  135. Relocation Offset is: d6e2f000
  136. spi_post_bind(spifc): req_seq = 0
  137. register usb cfg[0][1] = 00000000d7f2f2d0
  138. aml_i2c_init_port init regs for 0
  139. NAND: get_sys_clk_rate_mtd() 270, clock setting 200!
  140. NAND device id: 0 9f ff ff ff ff
  141. No NAND device found!!!
  142. nand init failed: -6
  143. get_sys_clk_rate_mtd() 270, clock setting 200!
  144. NAND device id: 0 9f ff ff ff ff
  145. No NAND device found!!!
  146. nand init failed: -6
  147. MMC: aml_priv->desc_buf = 0x00000000d3e1fa70
  148. aml_priv->desc_buf = 0x00000000d3e21db0
  149. SDIO Port B: 0, SDIO Port C: 1
  150. co-phase 0x3, tx-dly 0, clock 400000
  151. co-phase 0x3, tx-dly 0, clock 400000
  152. co-phase 0x3, tx-dly 0, clock 400000
  153. emmc/sd response timeout, cmd8, status=0x3ff2800
  154. emmc/sd response timeout, cmd55, status=0x3ff2800
  155. co-phase 0x3, tx-dly 0, clock 400000
  156. co-phase 0x1, tx-dly 0, clock 40000000
  157. aml_sd_retry_refix[983]:delay = 0x0,gadjust =0x2000
  158. [mmc_startup] mmc refix success
  159. init_part() 282: PART_TYPE_DOS
  160. [mmc_init] mmc init success
  161. start dts,buffer=00000000d3e24620,dt_addr=00000000d3e24620
  162. get_partition_from_dts() 71: ret 0
  163. parts: 17
  164. 00: logo 0000000000800000 1
  165. 01: recovery 0000000001800000 1
  166. 02: misc 0000000000800000 1
  167. 03: dtbo 0000000000800000 1
  168. 04: cri_data 0000000000800000 2
  169. 05: param 0000000001000000 2
  170. 06: boot 0000000001000000 1
  171. set has_boot_slot = 0
  172. 07: rsv 0000000001000000 1
  173. 08: metadata 0000000001000000 1
  174. 09: vbmeta 0000000000200000 1
  175. 10: tee 0000000002000000 1
  176. 11: vendor 0000000010000000 1
  177. 12: odm 0000000008000000 1
  178. 13: system 0000000050000000 1
  179. 14: product 0000000008000000 1
  180. 15: cache 0000000046000000 2
  181. 16: data ffffffffffffffff 4
  182. init_part() 282: PART_TYPE_DOS
  183. eMMC/TSD partition table have been checked OK!
  184. crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
  185. crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
  186. crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
  187. mmc env offset: 0x4d400000
  188. In: serial
  189. Out: serial
  190. Err: serial
  191. reboot_mode=cold_boot
  192. [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
  193. _verify_dtb_checksum()-3406: calc d789a65e, store d789a65e
  194. _verify_dtb_checksum()-3406: calc d789a65e, store d789a65e
  195. dtb_read()-3623: total valid 2
  196. update_old_dtb()-3604: do nothing
  197. aml_i2c_init_port init regs for 0
  198. fusb302_init: Device ID: 0x91
  199. CC connected in 1 as UFP
  200. fusb302 detect chip.port_num = 0
  201. amlkey_init() enter!
  202. [EFUSE_MSG]keynum is 1
  203. vpu: clk_level in dts: 7
  204. vpu: vpu_power_on
  205. vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
  206. vpu: vpu_module_init_config
  207. vpp: vpp_init
  208. vpp: g12a/b osd1 matrix rgb2yuv ..............
  209. vpp: g12a/b osd2 matrix rgb2yuv..............
  210. vpp: g12a/b osd3 matrix rgb2yuv..............
  211. cvbs: cpuid:0x29
  212. lcd: detect mode: tablet, key_valid: 0
  213. lcd: load config from dts
  214. lcd: pinctrl_version: 2
  215. lcd: use panel_type=lcd_1
  216. lcd: bl: pinctrl_version: 2
  217. lcd: bl: name: backlight_pwm, method: 1
  218. lcd: bl: aml_bl_power_ctrl: 0
  219. Net: dwmac.ff3f0000amlkey_init() enter!
  220. amlkey_init() 71: already init!
  221. [EFUSE_MSG]keynum is 1
  222. MACADDR:02:00:00:20:10:01(from chipid)
  223.  
  224. CONFIG_AVB2:
  225. Start read misc partition datas!
  226. info->magic =
  227. info->version_major = 1
  228. info->version_minor = 0
  229. info->slots[0].priority = 15
  230. info->slots[0].tries_remaining = 7
  231. info->slots[0].successful_boot = 0
  232. info->slots[1].priority = 14
  233. info->slots[1].tries_remaining = 7
  234. info->slots[1].successful_boot = 0
  235. info->crc32 = -1075449479
  236. active slot = 0
  237. wipe_data=successful
  238. wipe_cache=successful
  239. upgrade_step=0
  240. reboot_mode:::: cold_boot
  241.  
  242.  
  243. lcd: error: outputmode[1080p60hz] is not support
  244. hpd_state=1
  245. edid preferred_mode is 1080p60hz[16]
  246. hdr mode is 0
  247. dv mode is ver:0 len: 0
  248. hdr10+ mode is 0
  249. [OSD]load fb addr from dts:/meson-fb
  250. [OSD]set initrd_high: 0x7f800000
  251. [OSD]fb_addr for logo: 0x7f800000
  252. [OSD]load fb addr from dts:/meson-fb
  253. [OSD]fb_addr for logo: 0x7f800000
  254. [OSD]VPP_OFIFO_SIZE:0xfff01fff
  255. [CANVAS]canvas init
  256. [CANVAS]addr=0x7f800000 width=3840, height=2160
  257. Err imgread(L535):Logo header err.
  258. There is no valid bmp file at the given address
  259. [OSD]osd_hw.free_dst_data: 0,1919,0,1079
  260. [OSD]osd1_update_disp_freescale_enable
  261. cvbs: outputmode[1080p60hz] is invalid
  262. vpp: vpp_matrix_update: 2
  263. set hdmitx VIC = 16
  264. config HPLL = 5940000 frac_rate = 1
  265. HPLL: 0x3b3a04f7
  266. HPLL: 0x1b3a04f7
  267. HPLLv1: 0xdb3a04f7
  268. config HPLL done
  269. j = 6 vid_clk_div = 1
  270. hdmitx phy setting done
  271. hdmitx: set enc for VIC: 16
  272. enc_vpu_bridge_reset[1235]
  273. rx version is 1.4 or below div=10
  274. vpp: sdr_mode = 2
  275. vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
  276. normal power off
  277. boot wol: disable
  278. saradc: 0x28a, hw_ver: 0x31
  279.  
  280.  
  281. gpio: pin GPIOAO_7 (gpio 7) value is 1
  282. port mode is usb3.0
  283. Command: bcb uboot-command
  284. Start read misc partition datas!
  285. BCB hasn't any datas,exit!
  286.  
  287.  
  288. Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
  289. (Re)start USB...
  290. USB0: USB3.0 XHCI init start
  291. Register 3000140 NbrPorts 2
  292. Starting the controller
  293. USB XHCI 1.10
  294. scanning bus 0 for devices... 5 USB Device(s) found
  295. scanning usb for storage devices... 0 Storage Device(s) found
  296. ** Bad device usb 0 **
  297. ** Bad device usb 1 **
  298. ** Bad device usb 2 **
  299. ** Bad device usb 3 **
  300. card out
  301. pll tsensor avg: 0x20d3, u_efuse: 0x802c
  302. temp1: 44
  303. ddr tsensor avg: 0x20f5, u_efuse: 0x801d
  304. temp2: 46
  305. device cool done
  306. CONFIG_SYSTEM_AS_ROOT: systemroot
  307. system_mode: 1
  308.  
  309.  
  310. Start read misc partition datas!
  311. info->magic =
  312. info->version_major = 1
  313. info->version_minor = 0
  314. info->slots[0].priority = 15
  315. info->slots[0].tries_remaining = 7
  316. info->slots[0].successful_boot = 0
  317. info->slots[1].priority = 14
  318. info->slots[1].tries_remaining = 7
  319. info->slots[1].successful_boot = 0
  320. info->crc32 = -1075449479
  321. active slot = 0
  322. CONFIG_AVB2:
  323. active_slot: normal
  324. Err imgread(L328):Fmt unsupported!genFmt 0x0 != 0x3
  325. InUsbBurn
  326. noSof
  327. sof timeout, reset usb phy tuning
  328. card out
  329. [MSG]mmcinfo failed!
  330. card out
  331. (Re)start USB...
  332. USB0: USB3.0 XHCI init start
  333. Register 3000140 NbrPorts 2
  334. Starting the controller
  335. USB XHCI 1.10
  336. scanning bus 0 for devices... 5 USB Device(s) found
  337. scanning usb for storage devices... 0 Storage Device(s) found
  338. ** Bad device usb 0 **
  339. ** Bad device usb 0 **
  340. Start read misc partition datas!
  341. info->magic =
  342. info->version_major = 1
  343. info->version_minor = 0
  344. info->slots[0].priority = 15
  345. info->slots[0].tries_remaining = 7
  346. info->slots[0].successful_boot = 0
  347. info->slots[1].priority = 14
  348. info->slots[1].tries_remaining = 7
  349. info->slots[1].successful_boot = 0
  350. info->crc32 = -1075449479
  351. active slot = 0
  352. active_slot: normal
  353. Err imgread(L328):Fmt unsupported!genFmt 0x0 != 0x3
RAW Paste Data