Meraki MX80 Bootlog 2

U-Boot 2009.11-00043-gf4c39d3-serengeti_DEV_1.19.01 (Feb 15 2012 - 10:40:18)

CPU:   AMCC PowerPC 460 APM86290 at 1000 MHz PLB=500 MHz
       (SOC=1000 AXI=250 AHB=166 APB=83 EBC=100)
       Internal PCI arbiter disabled
       32 kB I-Cache 32 kB D-Cache
Board: Fullerene-2 - Meraki Fullerene Cloud Managed Router
I2C:   ready
DRAM:  -2 GB at 800MHz
Default enable MDIO for ETH0
Net:   Init Atheros ...
ethaddr[1]: ethaddr not set!
eth0
NAND:  1024 MiB
*** Warning - bad CRC or NAND, using default environment

Set serverpath and run meraki_netboot to netboot

Hit any key to stop autoboot:  1  0
Creating 1 MTD partitions on "nand0":
0x000000240000-0x000040000000 : "mtd=2"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=2"
UBI: MTD device size:            1021 MiB
UBI: number of good PEBs:        8174
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     4
UBI: available PEBs:             3404
UBI: total number of reserved PEBs: 4770
UBI: number of PEBs reserved for bad PEB handling: 81
UBI: max/mean erase counter: 55/53
Volume part1 found at volume id 0
read 0 bytes from volume 0 to 800000(buf address)
Read [33675264] bytes
setting meraki addr env fdt: 0x804000, kernel: 0x820000, ramdisk: 0xc00000
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 00820000 ...
   Image Name:   Linux-3.4.113
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    2445049 Bytes =  2.3 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 00c00000 ...
   Image Name:   Simple Ramdisk Image
   Image Type:   PowerPC Linux RAMDisk Image (lzma compressed)
   Data Size:    17327451 Bytes = 16.5 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 00804000
   Booting using the fdt blob at 0x804000
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 2ef79000, end 2ffff55b ... OK
[    0.000000] Meraki: removing an additional 17MB for the crypto acceleration driver on MX80/MX90
[    0.000000] New memory limit = 0x7df00000
[    0.000000] Using Serengeti machine description
[    0.000000] Linux version 3.4.113 (jenkins@atx101.meraki.com) (gcc version 4.8.3 (GCC) ) #4 Mon Mar 26 15:32:52 PDT 2018
[    0.000000] Found initrd at 0xaef79000:0xaffff55b
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00070000
[    0.000000]   Normal   empty
[    0.000000]   HighMem  0x00070000 -> 0x0007df00
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x0007df00
[    0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 511810
[    0.000000] Kernel command line: root=/dev/ram console=ttyS0,57600 ubi.mtd=ubi MERAKI_BOARD=fullerene mtdoops.mtddev=oops mem=0x7f000000
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes)
[    0.000000] Inode-cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Memory: 2023608k/2063360k available (4568k kernel code, 39752k reserved, 184k data, 259k bss, 180k init)
[    0.000000] Kernel virtual memory layout:
[    0.000000]   * 0xfffcf000..0xfffff000  : fixmap
[    0.000000]   * 0xffc00000..0xffe00000  : highmem PTEs
[    0.000000]   * 0xff200000..0xffc00000  : consistent mem
[    0.000000]   * 0xff200000..0xff200000  : early ioremap
[    0.000000]   * 0xf1000000..0xff200000  : vmalloc & ioremap
[    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:512 nr_irqs:512 16
[    0.000000] mpic: Setting up MPIC " MPIC     " version 1.2 at ddf400000, max 1 CPUs
[    0.000000] mpic: ISU size: 128, shift: 7, mask: 7f
[    0.000000] mpic: Initializing for 128 sources
[    0.000000] clocksource: timebase mult[800000] shift[23] registered
[    0.000060] pid_max: default: 32768 minimum: 301
[    0.000161] Mount-cache hash table entries: 512
[    0.001902] devtmpfs: initialized
[    0.002362] xor: measuring software checksum speed
[    0.050075]    8regs     :   747.200 MB/sec
[    0.100088]    8regs_prefetch:   667.600 MB/sec
[    0.150097]    32regs    :   783.600 MB/sec
[    0.200108]    32regs_prefetch:   712.000 MB/sec
[    0.200114] xor: using function: 32regs (783.600 MB/sec)
[    0.200215] NET: Registered protocol family 16
[    0.201777] gpiochip_add: registered GPIOs 230 to 255 on device: /hbf/ahb/apb/gpio@fa0004000
[    0.201984] gpiochip_add: registered GPIOs 214 to 229 on device: /hbf/ipp@ddd8b0000
[    0.202009] APM863xx detected (0x4002000A)
[    0.202061] APM SoC APM86xxx iPP CPU0 Hard CPU0
[    0.202447] PCI: Probing PCI hardware
[    0.213074] bio: create slab <bio-0> at 0
[    0.380317] raid6: int32x1    255 MB/s
[    0.550366] raid6: int32x2    347 MB/s
[    0.720425] raid6: int32x4    379 MB/s
[    0.890606] raid6: int32x8    246 MB/s
[    0.890612] raid6: using algorithm int32x4 (379 MB/s)
[    0.891494] SCSI subsystem initialized
[    0.892056] usbcore: registered new interface driver usbfs
[    0.892284] usbcore: registered new interface driver hub
[    0.892456] usbcore: registered new device driver usb
[    0.893668] Switching to clocksource timebase
[    0.895719] NET: Registered protocol family 2
[    0.901206] IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.902283] TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.908771] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[    0.909534] TCP: Hash tables configured (established 262144 bind 65536)
[    0.909543] TCP: reno registered
[    0.909555] UDP hash table entries: 1024 (order: 2, 16384 bytes)
[    0.909614] UDP-Lite hash table entries: 1024 (order: 2, 16384 bytes)
[    0.909888] NET: Registered protocol family 1
[    0.910075] Trying to unpack rootfs image as initramfs...
[   12.569933] Freeing initrd memory: 16924k freed
[   12.572738] qm_cfg: 1
[   12.594764] APM QM-TM Driver v0.1
[   12.714565] highmem bounce pool size: 64 pages
[   12.972993] msgmni has been set to 3539
[   12.987991] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[   12.988010] io scheduler noop registered
[   12.988016] io scheduler deadline registered (default)
[   12.990221] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[   13.024524] fa0000000.serial: ttyS0 at MMIO 0xfa0000000 (irq = 39) is a 16550
[   13.836912] console [ttyS0] enabled
[   13.851990] fa0001000.serial: ttyS1 at MMIO 0xfa0001000 (irq = 40) is a 16550
[   13.874365] fa0007000.serial: ttyS2 at MMIO 0xfa0007000 (irq = 41) is a 16550
[   13.896737] fa0008000.serial: ttyS3 at MMIO 0xfa0008000 (irq = 42) is a 16550
[   13.919029] Trying to register dev faulty etc
[   14.059192] brd: module loaded
[   14.135875] loop: module loaded
[   14.173283] mpt2sas version 12.100.00.00 loaded
[   14.206206] ahci-sata-of 500000000.sata: version 3.0
[   14.216210] ahci-sata-of 500000000.sata: forcing port_map 0x0 -> 0x1
[   14.236968] ahci-sata-of 500000000.sata: AHCI 0001.0300 32 slots 2 ports 3 Gbps 0x1 impl of mode
[   14.254462] ahci-sata-of 500000000.sata: flags: 64bit ncq sntf pm led clo only pmp pio slum part ccc apst
[   14.302338] scsi0 : ahci_of
[   14.315987] scsi1 : ahci_of
[   14.327828] ata1: SATA max UDMA/133 mmio [io  0x81ff26e700000080-0x0000 disabled] port 0x100 irq 44
[   14.345869] ata2: DUMMY
[   14.390677] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xa3 (Micron NAND 1GiB 1,8V 8-bit)
[   14.408408] Scanning device for bad blocks
[   16.375049] 5 ofpart partitions found on MTD device fa0140000.ufc.nand
[   16.388071] Creating 5 MTD partitions on "fa0140000.ufc.nand":
[   16.399682] 0x000000000000-0x000000100000 : "firmware"
[   16.420631] 0x000000100000-0x000000200000 : "environment"
[   16.447707] 0x000000200000-0x000000240000 : "oops-old"
[   16.474122] 0x000000240000-0x000040000000 : "ubi"
[   16.500573] 0x000000000000-0x000040000000 : "all"
[   16.539019] UBI: attaching mtd3 to ubi0
[   16.546689] UBI: physical eraseblock size:   131072 bytes (128 KiB)
[   16.559158] UBI: logical eraseblock size:    129024 bytes
[   16.569901] UBI: smallest flash I/O unit:    2048
[   16.579260] UBI: sub-page size:              512
[   16.588446] UBI: VID header offset:          512 (aligned 512)
[   16.600051] UBI: data offset:                2048
[   16.883813] ata1: Signature Update detected @ 0 msecs 0x00000101 1
[   17.094274] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   17.131806] ata1.00: ATA-8: WDC WD10EZRX-00A8LB0, 01.01A01, max UDMA/133
[   17.145154] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[   17.194028] ata1.00: configured for UDMA/133
[   17.202808] scsi 0:0:0:0: Direct-Access     ATA      WDC WD10EZRX-00A 01.0 PQ: 0 ANSI: 5
[   17.246882] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[   17.262154] sd 0:0:0:0: [sda] 4096-byte physical blocks
[   17.278817] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   17.324552] sd 0:0:0:0: [sda] Write Protect is off
[   17.344383] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   17.402475]  sda: sda1
[   17.417060] sd 0:0:0:0: [sda] Attached SCSI disk
[   22.354590] UBI: max. sequence number:       425719
[   22.406044] UBI: attached mtd3 to ubi0
[   22.413510] UBI: MTD device name:            "ubi"
[   22.423068] UBI: MTD device size:            1021 MiB
[   22.433118] UBI: number of good PEBs:        8174
[   22.442476] UBI: number of bad PEBs:         0
[   22.451314] UBI: number of corrupted PEBs:   0
[   22.460153] UBI: max. allowed volumes:       128
[   22.469338] UBI: wear-leveling threshold:    4096
[   22.478696] UBI: number of internal volumes: 1
[   22.487535] UBI: number of user volumes:     4
[   22.496374] UBI: available PEBs:             3323
[   22.505732] UBI: total number of reserved PEBs: 4851
[   22.515609] UBI: number of PEBs reserved for bad PEB handling: 162
[   22.527906] UBI: max/mean erase counter: 55/53
[   22.536746] UBI: image sequence number:  195825232
[   22.546376] UBI: background thread "ubi_bgt0d" started, PID 681
[   22.642822] PPC 4xx OCP EMAC driver, version 3.54
[   22.668311] PPP generic driver version 2.4.2
[   22.686647] PPP BSD Compression module registered
[   22.696044] PPP Deflate Compression module registered
[   22.706096] NET: Registered protocol family 24
[   22.722441] usbcore: registered new interface driver cdc_ether
[   22.734447] usbcore: registered new interface driver cdc_eem
[   22.753120] usbcore: registered new interface driver cdc_subset
[   22.765326] usbcore: registered new interface driver cdc_ncm
[   22.776611] Fusion MPT base driver 3.04.20
[   22.784760] Copyright (c) 1999-2008 LSI Corporation
[   22.794493] Fusion MPT SAS Host driver 3.04.20
[   22.817269] usbcore: registered new interface driver cdc_acm
[   22.828568] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   22.854275] usbcore: registered new interface driver usbserial
[   22.865911] usbserial: USB Serial Driver core
[   22.882055] usbcore: registered new interface driver option
[   22.893517] USB Serial support registered for GSM modem (1-port)
[   22.912935] usbcore: registered new interface driver qcserial
[   22.924742] USB Serial support registered for Qualcomm USB modem
[   22.944166] usbcore: registered new interface driver sierra
[   22.955615] USB Serial support registered for Sierra USB modem
[   22.977107] dummy_hcd dummy_hcd: USB Host+Gadget Emulator, driver 02 May 2005
[   22.991351] dummy_hcd dummy_hcd: Dummy host controller
[   23.007640] dummy_hcd dummy_hcd: new USB bus registered, assigned bus number 1
[   23.022146] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   23.035664] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   23.050037] usb usb1: Product: Dummy host controller
[   23.059914] usb usb1: Manufacturer: Linux 3.4.113 dummy_hcd
[   23.071002] usb usb1: SerialNumber: dummy_hcd
[   23.085900] hub 1-0:1.0: USB hub found
[   23.093382] hub 1-0:1.0: 1 port detected
[   23.117661] input: gpio_keys_polled.4 as /devices/hbf.0/gpio_keys_polled.4/input/input0
[   23.149442] i2c /dev entries driver
[   23.176946] gpiochip_add: registered GPIOs 190 to 213 on device: tca6424
[   23.190329] EVERYTHNIG WENT GREAT
[   23.215333] EVERYTHNIG WENT GREAT
[   23.233160] booke_wdt: powerpc book-e watchdog driver loaded
[   23.249691] md: linear personality registered for level -1
[   23.260644] md: raid0 personality registered for level 0
[   23.271213] md: raid1 personality registered for level 1
[   23.281782] md: raid10 personality registered for level 10
[   23.292696] md: raid6 personality registered for level 6
[   23.303264] md: raid5 personality registered for level 5
[   23.313835] md: raid4 personality registered for level 4
[   23.338495] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[   23.360994] device-mapper: multipath: version 1.3.2 loaded
[   23.371949] device-mapper: multipath round-robin: version 1.0.0 loaded
[   23.384938] device-mapper: multipath queue-length: version 0.1.0 loaded
[   23.398099] device-mapper: multipath service-time: version 0.2.0 loaded
[   23.415325] device-mapper: dm-log-userspace: version 1.1.0 loaded
[   23.481323] APMSEC: APM 862xx SoC security accelerator driver v0.1
[   23.503872] usbcore: registered new interface driver usbhid
[   23.514977] usbhid: USB HID core driver
[   23.522607] oprofile: using timer interrupt.
[   23.531389] TCP: cubic registered
[   23.537997] Initializing XFRM netlink socket
[   23.546505] NET: Registered protocol family 17
[   23.555377] NET: Registered protocol family 15
[   23.564224] L2TP core driver, V2.0
[   23.571011] PPPoL2TP kernel driver, V2.0
[   23.578814] 8021q: 802.1Q VLAN Support v1.8
[   23.607511] /mnt/jenkins/workspace/router/prod-signing/wired-13/linux-3.4/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[   23.630862] devtmpfs: mounted
[   23.639320] Freeing unused kernel memory: 180k freed
[   23.656896] Made it into bootsh: Mar 26 2018 15:22:26
[   23.667240] bootsh build wired-13-201803231209-Ge7981ad3-loss-rel
[   23.777978] UBIFS: recovery needed
[   23.978112] UBIFS: recovery completed
[   23.985432] UBIFS: mounted UBI device 0, volume 3, name "storage"
[   23.997560] UBIFS: file system size:   535062528 bytes (522522 KiB, 510 MiB, 4147 LEBs)
[   24.013490] UBIFS: journal size:       26836992 bytes (26208 KiB, 25 MiB, 208 LEBs)
[   24.028731] UBIFS: media format:       w4/r0 (latest is w4/r0)
[   24.040336] UBIFS: default compressor: lzo
[   24.048489] UBIFS: reserved for root:  4952683 bytes (4836 KiB)
In manufacturing: FALSE
[   24.102349]
init started: BusyBox v1.24.1 (2018-03-26 12:57:58 PDT)
WARNING! THIS CONSOLE IS LOGGED! UNAUTHORIZED ACCESS FORBI[   24.200686] Sat Jan  1 00:00:00 UTC 2000
DDEN!
[   24.434035] sysctl: error: 'kernel.softlockup_panic' is an unknown key
[   24.447347] sysctl: error: 'kernel.watchdog_thresh' is an unknown key
[   24.460344] sysctl: error: 'vm.extfrag_threshold' is an unknown key
[   24.848338] sysctl -w vm.panic_on_oom=2
[   24.861437] vm.panic_on_oom = 2
[   25.086384] click: starting router thread pid 1110 (afa3ab00)
[   25.166142] elts_meraki: module license 'unspecified' taints kernel.
[   25.477524] Single synchronous check for reset
[   25.545811] GobiNet: 2013-10-08/NTGR_2.21
[   25.583762] usbcore: registered new interface driver GobiNet
[   25.668358] usbcore: registered new interface driver GobiSerial
[   25.717079] USB Serial support registered for GobiSerial
[   25.727700] GobiSerial: 2013-10-08/NTGR_2.12:GobiSerial
[   25.777408] dwc_otg: version 2.60a 22-NOV-2006
[   25.787556] Synopsis DWC USB-OTG ID 0x4f54291a
[   25.996591] dwc_otg: Using DMA mode
[   26.003537] usb-otg fa0100000.usb: DWC OTG Controller
[   26.021831] usb-otg fa0100000.usb: new USB bus registered, assigned bus number 2
[   26.036620] usb-otg fa0100000.usb: irq 79, io mem 0xfa0100000
[   26.048196] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[   26.061715] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   26.076099] usb usb2: Product: DWC OTG Controller
[   26.085460] usb usb2: Manufacturer: Linux 3.4.113 dwc_otg_hcd
[   26.096892] usb usb2: SerialNumber: dwc_otg_hcd
[   26.116258] hub 2-0:1.0: USB hub found
[   26.123791] hub 2-0:1.0: 1 port detected
[   26.141805] dwc_otg: Dedicated Tx FIFOs mode
[   26.201750] dwc_otg: version 2.60a 22-NOV-2006
[   26.535337]
[   26.545083] boot 29 build wired-13-201803231209-Ge7981ad3-loss-rel board wired-powerpc mac {redacted}
[   26.567407] /usr/bin/snort-version
[   26.581771] Module: proclikefs  .text=0xf10d5000 .data= .bss=0xf10d5d80
[   26.581782] Module: merakiclick  .text=0xf28e1000 .data=0xf29f0950 .bss=0xf29f0da0
[   26.581787] Module: elts_meraki  .text=0xf3014000 .data=0xf330b1c8 .bss=0xf330d860
[   26.581791] Module: GobiNet  .text=0xf10f1000 .data=0xf10fa220 .bss=0xf10fa464
[   26.581795] Module: GobiSerial  .text=0xf153c000 .data=0xf153d094 .bss=0xf153d548
[   26.581799] Module: apm_otg  .text=0xf2581000 .data=0xf25921b0 .bss=0xf25926d0
[   26.581803] Module: dwc_otg  .text=0xf34e4000 .data=0xf34f69e0 .bss=0xf34f6f04
[   26.581808] Module: scsi_wait_scan  .text=0xf10fd000 .data= .bss=
[   26.695292] ttyS0: 1 input overrun(s)
[   26.737332] ramoops: platform device not found, using module parameters
[   26.815662] phram: phram-oops device: 0x100000 at 0x7df00000
[   28.329463] kjournald starting.  Commit interval 5 seconds
[   28.342619] EXT3-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended
[   28.383065] EXT3-fs (sda1): using internal journal
[   28.396968] EXT3-fs (sda1): recovery complete
[   28.405710] EXT3-fs (sda1): mounted filesystem with ordered data mode
[   30.442644] chatter: to_bird :: ToHost: device 'bird' went down
[   30.468861] chatter: to_bird :: ToHost: device 'bird' came up
[   30.496460] device sw0 entered promiscuous mode
[   30.506157] changing MTU from 1500 to 1508
[   30.514656] sw0 Link is up with speed 1000 Mbps
[   30.532941] device sw1 entered promiscuous mode
[   30.542485] changing MTU from 1500 to 1508
[   30.551115] sw1 Link is up with speed 1000 Mbps
[   41.917743] chatter: _to_linux_test_client :: ToHost: device 'test_client' went down
[   44.075622] chatter: big_acl :: BigACL: skipping undersized restore buffer (buf size: 0)