#!/bin/bash

# ----------------------------------------------------------------------------------
# Script for checking the temperature reported by the ambient temperature sensor,
# and if deemed too high send the raw IPMI command to enable dynamic fan control.
#
# This script was designed around the X11sat-f motherboard and having a nonPWM CPU fan
#
# Requires:
# ipmitool: apt-get install ipmitool
# slacktee.sh: https://github.com/course-hero/slacktee

#https://gist.github.com/kidpixo/04d61b42221f6bc8489b
#https://forums.servethehome.com/index.php?resources/supermicro-x9-x10-x11-fan-speed-control.20/
# ----------------------------------------------------------------------------------

### VARIABLES FOR USER TO SET ###

# unRAID drives that are in the array/backplane of the fan we need to control
HD[1]=/dev/sdb
HD[2]=/dev/sdc
HD[3]=/dev/sdd
HD[4]=/dev/sde
HD[5]=/dev/sdf
HD[6]=/dev/sdg
HD[7]=/dev/sdh
HD[8]=/dev/sdi
HD[9]=/dev/sdj
HD[10]=/dev/sdk
HD[11]=/dev/sdl
HD[12]=/dev/sdm
HD[13]=/dev/sdn
HD[14]=/dev/sdo
HD[15]=/dev/sdp
HD[16]=/dev/sdq
#HD[17]=/dev/sdr
#HD[18]=/dev/sds
#HD[19]=/dev/sdt
#HD[20]=/dev/sdu
#HD[21]=/dev/sdv
#HD[22]=/dev/sdw
#HD[23]=/dev/sdx
#HD[24]=/dev/sdy

# Temperatures to change fan speed at
# Any temp between OFF and HIGH will cause fan to run in a mapped value between idle and high speed 
TEMP_IDLE=28	# Anything between this number and below	- fan is at idle speed
TEMP_HIGH=40    # Anything above this number				- fan is at alert speed

# Fan speed settings. For my board its a value between 0x00 and 0x64 (0% to 100%)
FAN_OFF=0
FAN_IDLE=8
FAN_HIGH=20
FAN_ALERT=50

### END USER SET VARIABLES ###
# Do not modify anything below

# Init Program variables
NUM_OF_DRIVES=${#HD[@]}
TEMP_HIGHEST=0
CURRENT_DRIVE=1
TEMP_CURRENT=0

# while loop to get the highest temperature of active drives. 
# If all are spun down then high temp will be set to 0.
while [ "$CURRENT_DRIVE" -le "$NUM_OF_DRIVES" ]
do
	#echo "Loop of: "${HD[$CURRENT_DRIVE]}
	SLEEPING=`hdparm -C ${HD[$CURRENT_DRIVE]} | grep -c standby`
	#echo $SLEEPING
	
	if [[ $SLEEPING -eq 0 ]]
	then
		TEMP_CURRENT=`smartctl -A ${HD[$CURRENT_DRIVE]} | grep Temperature_Celsius | awk '{print $10}'`
		if [ $TEMP_HIGHEST -le $TEMP_CURRENT ]; then
			TEMP_HIGHEST=$TEMP_CURRENT
		fi
	fi
	
	#echo $TEMP_CURRENT
	let "CURRENT_DRIVE+=1"
done

echo "Highest temp is: "$TEMP_HIGHEST

# Set the PWM through IPMI
INTERPOL_RANGE=$(($TEMP_HIGHEST-$TEMP_IDLE))
if [ $TEMP_HIGHEST -gt $TEMP_HIGH ]
then 
	FAN_SPEED=$FAN_ALERT

elif [ $INTERPOL_RANGE -gt 0 ]
then
	FAN_SPEED=$((((($TEMP_HIGHEST - $TEMP_IDLE) * ($FAN_HIGH - $FAN_IDLE)) / ($TEMP_HIGH - $TEMP_IDLE)) + $FAN_IDLE))
	
else
	FAN_SPEED=$FAN_IDLE
fi

#echo "Setting fan speed to: "$FAN_SPEED
if [ $FAN_SPEED -lt 10 ]
then
	COMMANDSTR="ipmitool raw 0x30 0x70 0x66 0x01 0x00 0x0"$FAN_SPEED
else
	COMMANDSTR="ipmitool raw 0x30 0x70 0x66 0x01 0x00 0x"$FAN_SPEED
fi

echo "Running command: "$COMMANDSTR
`$COMMANDSTR`