Texas Instruments X-Loader 1.5.0 (Sep 28 2011 - 02:50:26) Beagle xM Reading boot sector Loading u-boot.bin from mmc U-Boot 2011.06 (Sep 28 2011 - 02:54:31) OMAP3630/3730-GP ES2.1, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz OMAP3 Beagle board + LPDDR/NAND I2C: ready DRAM: 512 MiB NAND: 0 MiB MMC: OMAP SD/MMC: 0 *** Warning - readenv() failed, using default environment In: serial Out: serial Err: serial Beagle unknown 0x02 No EEPROM on expansion board Die ID #1c0400229ff800000163810c0f033025 Hit any key to stop autoboot: 0 OMAP3 beagleboard.org # OMAP3 beagleboard.org # OMAP3 beagleboard.org # OMAP3 beagleboard.org # sete console "ttyO2,115200n8" OMAP3 beagleboard.org # sete sd_boot "mmc rescan ${mmcdev}; run loadbootscript; run bootscript; run loaduimage; run mmcboot;" OMAP3 beagleboard.org # OMAP3 beagleboard.org # run sd_boot ## Error: "loadbootscript" not defined ## Error: "bootscript" not defined reading uImage 2809656 bytes read Booting from mmc ... ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-2.6.37.6-yocto-standard+ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2809592 Bytes = 2.7 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Linux version 2.6.37.6-yocto-standard+ (rber@yocto-1) (gcc version 4.6.1 20110627 (prerelease) (GCC) ) #1 PREEMPT Wed Sep 28 01:00:16 EEST 2011 CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: OMAP3 Beagle Board Reserving 12582912 bytes SDRAM for VRAM Memory policy: ECC disabled, Data cache writeback OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk ) SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 126976 Kernel command line: console=ttyO2,115200n8 mpurate=auto vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapfb.debug=y omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) allocated 2621440 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Memory: 500MB = 500MB total Memory: 498700k/498700k available, 25588k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xffc00000 - 0xffe00000 ( 2 MB) vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc0056000 ( 312 kB) .text : 0xc0056000 - 0xc0573afc (5239 kB) .data : 0xc0574000 - 0xc05c9700 ( 342 kB) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Preemptable hierarchical RCU implementation. NR_IRQS:402 Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz Reprogramming SDRC clock to 332000000 Hz GPMC revision 5.0 IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts Total of 96 interrupts on 1 active controller OMAP clockevent source: GPTIMER12 at 32768 Hz Console: colour dummy device 80x30 Calibrating delay loop... 500.97 BogoMIPS (lpj=1953792) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 Initializing cgroup subsys debug Initializing cgroup subsys ns ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup. Initializing cgroup subsys cpuacct Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys blkio CPU: Testing write buffer coherency: ok ftrace: allocating 16422 entries in 33 pages devtmpfs: initialized regulator: core version 0.5 regulator: dummy: NET: Registered protocol family 16 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 omap_mux_init: Add partition: #1: core, flags: 0 OMAP3 Beagle Rev: xM C Found NAND on CS0 Registering NAND on CS0 Unable to get DVI reset GPIO beagle_opp_init: turbo OPPs enabled! OMAP DMA hardware revision 5.0 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb omap_device: omap_i2c.1: new worst case activate latency 0: 30517 omap_i2c omap_i2c.1: bus 1 rev4.0 at 2600 kHz twl4030: PIH (irq 7) chaining IRQs 368..375 twl4030: power (irq 373) chaining IRQs 376..383 twl4030: gpio (irq 368) chaining IRQs 384..401 regulator: VUSB1V5: 1500 mV normal standby regulator: VUSB1V8: 1800 mV normal standby regulator: VUSB3V1: 3100 mV normal standby twl4030_usb twl4030_usb: Initialized TWL4030 USB module regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby regulator: VDAC: 1800 mV normal standby regulator: VDVI: 1800 mV normal standby regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby omap_device: omap_i2c.1: new worst case deactivate latency 0: 30517 omap_i2c omap_i2c.2: bus 2 rev4.0 at 400 kHz omap_i2c omap_i2c.3: bus 3 rev4.0 at 100 kHz Advanced Linux Sound Architecture Driver Version 1.0.23. Switching to clocksource 32k_counter musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 musb_hdrc musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 974 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) OMAP DSS rev 2.0 OMAP DISPC rev 3.0 OMAP VENC rev 2 OMAP DSI rev 1.0 Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2 console [ttyO2] enabled omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP UART3 brd: module loaded omap2-nand driver initializing No NAND device found. No NAND device found. usbcore: registered new interface driver kaweth pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver usbcore: registered new interface driver pegasus usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver dm9601 usbcore: registered new interface driver smsc75xx usbcore: registered new interface driver smsc95xx usbcore: registered new interface driver net1080 usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus usbcore: registered new interface driver MOSCHIP usb-ethernet driver usbcore: registered new interface driver int51x1 cdc_ncm: 30-Nov-2010 usbcore: registered new interface driver cdc_ncm console [netcon0] enabled netconsole: network logging started ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-omap.0 supply hsusb0 not found, using dummy regulator ehci-omap.0 supply hsusb1 not found, using dummy regulator ehci-omap ehci-omap.0: OMAP-EHCI Host Controller ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec cpuidle: using governor ladder cpuidle: using governor menu mmci-omap-hs: probe of mmci-omap-hs.1 failed with error -16 usbcore: registered new interface driver usbhid usbhid: USB HID core driver OMAP3 Beagle/Devkit8000 SoC init asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok ALSA device list: #0: omap3beagle TCP cubic registered NET: Registered protocol family 17 Registering the dns_resolver key type VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 ThumbEE CPU extension supported. Power Management for TI OMAP3. sr_init: No PMIC hook to init smartreflex smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized SmartReflex Class3 initialized clock: disabling unused clocks to save power registered taskstats version 1 fbcvt: 1024x768@60: CVT Name - .786M3-R Console: switching to colour frame buffer device 128x48 mmc0: host does not support reading read-only switch. assuming write-enable. mmc0: new high speed SDHC card at address 0001 mmcblk0: mmc0:0001 00000 7.60 GiB mmcblk0: p1 p2 regulator_init_complete: incomplete constraints, leaving VDAC on twl_rtc twl_rtc: setting system clock to 2011-09-28 01:18:59 UTC (1317172739) EXT3-fs: barriers not enabled kjournald starting. Commit interval 5 seconds usb 1-2: new high speed USB device using ehci-omap and address 2 EXT3-fs (mmcblk0p2): using internal journal EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode VFS: Mounted root (ext3 filesystem) on device 179:2. devtmpfs: mounted Freeing init memory: 312K INIT: version 2.88 bootinghub 1-2:1.0: USB hub found hub 1-2:1.0: 5 ports detected usb 1-2.1: new high speed USB device using ehci-omap and address 3 Starting udevsmsc95xx v1.0.4 smsc95xx 1-2.1:1.0: usb0: register 'smsc95xx' at usb-ehci-omap.0-2.1, smsc95xx USB 2.0 Ethernet, 82:57:97:8c:bf:03 udev[63]: starting version 164 NET: Registered protocol family 10 Starting Bootlog daemon: usb0: link up, 100Mbps, full-duplex, lpa 0x4DE1 bootlogd. Yocto (Built by Poky 5.0) 1.0+snapshot-20110927 beagleboard ttyO2 beagleboard login: D-BUS per-session daemon address is: unix:abstract=/tmp/dbus-Myf9CxQmxZ,guid=58581610bb2a5bfee960414900000015 gnome-keyring-daemon: Missing argument for --componentsgnome-keyring-daemon: Missing argument for --componentsGNOME_KEYRING_CONTROL=/tmp/keyring-920H3H SSH_AUTH_SOCK=/tmp/keyring-920H3H/ssh GPG_AGENT_INFO=/tmp/keyring-920H3H/gpg:0:1 GNOME_KEYRING_PID=390 GNOME_KEYRING_CONTROL=/tmp/keyring-TiNPLJ SSH_AUTH_SOCK=/tmp/keyring-TiNPLJ/ssh GPG_AGENT_INFO=/tmp/keyring-TiNPLJ/gpg:0:1 GNOME_KEYRING_PID=392 gnome-keyring-daemon: Missing argument for --componentsGNOME_KEYRING_CONTROL=/tmp/keyring-fCulvS SSH_AUTH_SOCK=/tmp/keyring-fCulvS/ssh GPG_AGENT_INFO=/tmp/keyring-fCulvS/gpg:0:1 GNOME_KEYRING_PID=398 gnome-keyring-daemon: Missing argument for --componentsGNOME_KEYRING_CONTROL=/tmp/keyring-P0eOEV SSH_AUTH_SOCK=/tmp/keyring-P0eOEV/ssh GPG_AGENT_INFO=/tmp/keyring-P0eOEV/gpg:0:1 GNOME_KEYRING_PID=402 matchbox: Cant find a keycode for keysym 269025056 matchbox: ignoring key shortcut XF86Calendar=!$contacts matchbox: Cant find a keycode for keysym 2809 matchbox: ignoring key shortcut telephone=!$dates matchbox: Cant find a keycode for keysym 269025050 matchbox: ignoring key shortcut XF86Start=!matchbox-remote -desktop [settings daemon] Forking. run with -n to prevent fork ** (matchbox-desktop:416): WARNING **: Error loading icon: Icon 'system-file-manager' not present in theme ** (matchbox-desktop:416): WARNING **: Error loading icon: Icon 'preferences-desktop' not present in theme ** (matchbox-desktop:416): WARNING **: Error loading icon: Icon 'computer' not present in theme Yocto (Built by Poky 5.0) 1.0+snapshot-20110927 beagleboard ttyO2 beagleboard login: root root@beagleboard:~# ping 192.168.42.100 PING 192.168.42.100 (192.168.42.100): 56 data bytes 64 bytes from 192.168.42.100: seq=0 ttl=64 time=0.824 ms 64 bytes from 192.168.42.100: seq=1 ttl=64 time=0.794 ms 64 bytes from 192.168.42.100: seq=2 ttl=64 time=0.763 ms  --- 192.168.42.100 ping statistics --- 3 packets transmitted, 3 packets received, 0% packet loss round-trip min/avg/max = 0.763/0.793/0.824 ms root@beagleboard:~#