smartctl 5.42 2011-10-20 r3458 [x86_64-linux-3.2.11] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: ST3000DM001-9YN166 Serial Number: S1F0MY64 LU WWN Device Id: 5 000c50 051508cc4 Firmware Version: CC4B User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Wed Mar 20 20:13:03 2013 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 119) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 575) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 112 077 006 Pre-fail Always - 47729088 3 Spin_Up_Time 0x0003 093 092 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 105 5 Reallocated_Sector_Ct 0x0033 095 095 036 Pre-fail Always - 6616 7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 119894791 9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 6147 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 20 183 Runtime_Bad_Block 0x0032 099 099 000 Old_age Always - 1 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 5380 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 061 038 045 Old_age Always In_the_past 39 (0 4 43 37 0) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 9 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 351 194 Temperature_Celsius 0x0022 039 062 000 Old_age Always - 39 (0 25 0 0 0) 197 Current_Pending_Sector 0x0012 084 054 000 Old_age Always - 2656 198 Offline_Uncorrectable 0x0010 084 054 000 Old_age Offline - 2656 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 127448859547259 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 123403418370269 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 126649577412316 SMART Error Log Version: 1 ATA Error Count: 5378 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5378 occurred at disk power-on lifetime: 4898 hours (204 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 80 ff ff ff 4f 00 8d+12:48:53.788 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 8d+12:48:53.780 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 8d+12:48:53.780 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 8d+12:48:53.780 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 8d+12:48:53.779 SET FEATURES [Set transfer mode] Error 5377 occurred at disk power-on lifetime: 4898 hours (204 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 80 ff ff ff 4f 00 8d+12:48:50.849 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 8d+12:48:50.841 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 8d+12:48:50.841 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 8d+12:48:50.840 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 8d+12:48:50.840 SET FEATURES [Set transfer mode] Error 5376 occurred at disk power-on lifetime: 4898 hours (204 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 80 ff ff ff 4f 00 8d+12:48:47.879 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 8d+12:48:47.872 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 8d+12:48:47.872 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 8d+12:48:47.871 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 8d+12:48:47.871 SET FEATURES [Set transfer mode] Error 5375 occurred at disk power-on lifetime: 4898 hours (204 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 80 ff ff ff 4f 00 8d+12:48:44.941 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 8d+12:48:44.933 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 8d+12:48:44.933 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 8d+12:48:44.933 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 8d+12:48:44.932 SET FEATURES [Set transfer mode] Error 5374 occurred at disk power-on lifetime: 4898 hours (204 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 80 ff ff ff 4f 00 8d+12:48:41.977 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 8d+12:48:41.969 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 8d+12:48:41.969 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 8d+12:48:41.968 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 8d+12:48:41.968 SET FEATURES [Set transfer mode] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 70% 6133 2381750472 # 2 Extended offline Aborted by host 70% 6130 - # 3 Extended offline Completed: read failure 70% 5965 2381750472 # 4 Extended offline Completed: read failure 70% 5798 2381750472 # 5 Extended offline Completed: read failure 70% 5629 2381750472 # 6 Extended offline Completed: read failure 70% 5465 2381750472 # 7 Extended offline Completed: read failure 70% 5388 2381750472 # 8 Extended offline Completed: read failure 70% 5295 2381750472 # 9 Short offline Completed without error 00% 4817 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.