Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- 3cidxs3deaca4b67cdb5ffa460e0cdbf8b287060bb4366S
- #xos2P68-100 (sfla 128kbytes. subid 0x00/d8) [serial#d3bff1f67403ed644bdf8a06f93 ebaca]
- #stepxmb 0xcb - 3
- #chpll 0x01000024/0x00000201 -> 0x01000034/0x00000101... actual sys=357MHz
- #DRAM setup (method=0x10015858) ...
- #DRAM0 Window : 0x#2e#2c#2c#2c# (22)
- #DRAM0 Settings: WD=0x0b0b0b0b RG=0x0b0b0b0b RR=0x0b0b0b0b RF=0x0c0c0c0c
- #poisoned 131072 pages with 0x9ecadc84
- #step6 @0*** zxenv has been customized compared to build ***
- --- review xmasboot/configs/1018-E1.config for details [xmbcc-ezbootc1-nand_st2] ---
- xloadsize=79876
- xload rc=6
- ezbootc1 @0x00000000 (nand_st2) (actual cpu=@715MHz/dsp=357MHz/sys=357MHz)
- on 8670 rev ES2 (subid 0x00) a2=0x00000002 a3=0x00000003
- step12
- #step22
- ruamm0 [0x8ca00000,0x9f2f0000[ (~311361536 bytes)
- [0x9f1f0000,xos_public_ga=0x9f200000[ and [0x9f280000,0x9f2f0000[ are lost for a lignment)
- ex_ga=0x9f1efcd4
- [0x9e800000,ios_ga=0x9e800000[ and [0x9eeacfc1,0x9f1dfcbc[ are lost for alignmen t)
- GW32 0x0006f008 0x80000000 [va=0x84000000]
- GW32 0x0006f00c 0x84000000 [va=0x88000000]
- GW32 0x0006f010 0x88000000 [va=0x8c000000]
- step33
- xos2k client version=19, server version=19
- xos2 SHA-1 = 3deaca4b67cdb5ffa460e0cdbf8b287060bb4366
- xos version = 0x68
- xos serial = d3bff1f67403ed644bdf8a06f93ebaca
- Using zbootxenv ga=0x9e7fbff4 (va=0xba7fbff4)
- **************************************
- * SMP86xx zboot start ...
- * Version: 3.1.0
- * Started at 0xd00f3ad4.
- * Configurations (chip revision: 3):
- * Enabled checkpoints.
- **************************************
- DRAM0 dunit_cfg/delay0_ctrl (0x35140017/0x4565132b).
- DRAM1 dunit_cfg/delay0_ctrl (NA/NA).
- Using UART port 0 as console.
- Board ID.: palace
- Setting up H/W from XENV block at 0xba7fbff4.
- Setting <SYSCLK avclk_mux> to 0x17400000.
- Setting <SYSCLK hostclk_mux> to 0x00000131.
- Setting <IRQ rise edge trigger lo> to 0xff28ca06.
- Setting <IRQ fall edge trigger lo> to 0x0000c000.
- Setting <IRQ rise edge trigger hi> to 0x8c10001f.
- Setting <IRQ fall edge trigger hi> to 0x00000000.
- Setting <IRQ GPIO map> to 0x000a0800.
- Setting <PB default timing> to 0x03080202.
- Setting <PB timing0> to 0x03060404.
- Keeping <PB Use timing0> to 0x000003f3.
- Setting <PB timing1> to 0x10101010.
- Setting <PB Use timing1> to 0x000003f4.
- Setting <PB CS Config> to 0x00370043.
- Enabled Devices: 0x003002f0
- Ethernet1 IR FIP I2CM I2CS SDIO1 USB
- cd#0 disabled
- cd#1 disabled
- cd#2 want 96000000Hz: setting of 0x0000000043800000-2^28
- cd#2 cannot measure
- cd#3 disabled
- cd#4 disabled
- cd#5 disabled
- cd#6 want 96000000Hz: setting of 0x0000000043800000-2^28
- cd#6 measured to 0kHz
- cd#7 disabled
- cd#8 disabled
- cd#9 disabled
- cd#10 disabled
- cd#11 disabled
- GPIO dir/data = 0x00000a00/0x00000a00
- UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
- UART1 GPIO mode/dir/data = 0x00/0x00/0x00
- UART2 GPIO mode/dir/data = 0x00/0x00/0x00
- MAC1: 00:90:a9:c7:24:51
- XENV block processing completed.
- Using UART port 0 as console.
- xmboot booted from devtype: 0, chipsel: 0, phyblocknum: 0, devflags: 1
- Explicit boot order specified:
- 0x00 : devtype=0, CS=0
- 0x01 : devtype=0, CS=1
- 0x40 : devtype=4, CS=0
- 0x41 : devtype=4, CS=1
- ezboot buffers, setup in DRAM bank#0:
- Alloting 2097152 bytes for heap.
- Alloting 16777216 bytes for reading.
- Alloting 16777216 bytes for decryption.
- xmat romfs goes to 0x9e3fbfe0 (ga)
- xmat romfs goes to 0xb63fbfe0 (va)
- Trying devtype=0 chipsel=0
- xmboot booted from NAND, setting device flags = 0x010b1000
- nandlib_init(cs=0, reserved_phyblocks=4096, pagesize_shift=11, extecc=1
- nand_probe 0x0xd0103854
- reserved phyblocks exceeds range, skipping ..
- Reading xmaterial from BBA physical zone
- Reading NAND CS0, addr 0x00d80000, size 0x00000800 to 0xb63fbfe0
- Reading NAND CS0, addr 0x00d80800, size 0x00022400 to 0xb63fc7e0
- File xtask_loader.xload found
- process_imat_romfs,1523
- get_firmware_sign,1469: *sign=69736973
- found imat romfs @ 0x01280000
- imap romfs goes to 0x9dffbfc0 (ga)
- imap romfs goes to 0xb5ffbfc0 (va)
- Trying devtype=0 chipsel=0
- xmboot booted from NAND, setting device flags = 0x010b1000
- Reading imaterial from BBA physical zone
- Reading NAND CS0, addr 0x01280000, size 0x00000800 to 0xb5ffbfc0
- Reading NAND CS0, addr 0x01280800, size 0x003aac00 to 0xb5ffc7c0
- File itask_loader.iload found
- Channel pending 1596
- Channel pending 1369882
- Channel pending 2932242
- Channel pending 4494650
- Channel pending 6057090
- Channel pending 7619550
- Channel pending 9182070
- Channel pending 10744382
- Channel pending 12369386
- Trying devtype=0 chipsel=0
- xmboot booted from NAND, setting device flags = 0x010b1000
- reading z.boot2 (vzx=0xba7fbff4) is 0x00780000, BBA physical zone
- Reading NAND CS0, addr 0x00780000, size 0x00000800 to 0x01840000
- Reading NAND CS0, addr 0x00780800, size 0x00400c00 to 0x01840800
- Found.
- ROMFS found at 0x0x01840000, Volume name = MIPSLINUX_XLOAD
- Found 1 file(s) to be processed in ROMFS.
- Processing vmlinux_xload.zbf (start: 0x01840090, size: 0x004010d4)
- Checking zboot file signature .. OK.
- Warning: header version mismatched.
- *** Fully Encrypted.
- src_addr = 0x018400b0, dest addr = 0x02840000
- XLOADING src=0x818400b0, dest=0x82840000, size=0x004010b4
- xload.c:68: Waiting for XLOAD completion.
- xload.c:78: XLOAD done, status = 0x6.
- Decompressing to 0x84000000 .. OK (6987763/0x6a9ff3).
- Load time total 0/0 msec.
- Execute at 0x844ac000 ..
- Linux version 2.6.22.19-49-4 (release@TP-SERVER2) (gcc version 4.3.2 (Sourcery G++ Lite 4.3-51) ) #11 PREEMPT Mon Mar 26 18:01:20 CST 2012
- Mixed DRAM usage enabled.
- Configured for SMP8670, detected SMP8670 (revision ES2).
- Detected CPU/System/DSP Frequencies: 715.50/357.75/357.75MHz
- SMP86xx Enabled Devices under Linux/XENV 0x9e7fbff4 = 0x003002f0
- Ethernet1 IR FIP I2CM I2CS SDIO1 USB
- Desired kernel memory size: 0x05000000
- Max. DRAM0/1 size allowed: 0x0ca00000/0x00000000
- Mapped 0x80000000(size 0x04000000) via remap2
- Mapped 0x84000000(size 0x01000000) via remap3
- Final kernel memory size: 0x05000000
- CPU revision is: 0001937c
- FPU revision is: 01739300
- Determined physical RAM map:
- memory: 05000000 @ 04000000 (usable)
- Desired kernel memory size: 0x0c800000
- Max. DRAM0/1 size allowed: 0x0ca00000/0x00000000
- Mapped 0x80000000(size 0x04000000) via remap2
- Mapped 0x84000000(size 0x04000000) via remap3
- Mapped 0x88000000(size 0x04000000) via remap4
- Mapped 0x8c000000(size 0x00800000) via remap5
- Final kernel memory size: 0x0c800000
- User-defined physical RAM map:
- memory: 0c800000 @ 04000000 (usable)
- Wasting 131072 bytes for tracking 4096 unused pages
- Initrd not found or empty - disabling initrd
- On node 0 totalpages: 16896
- DMA zone: 33 pages used for memmap
- DMA zone: 0 pages reserved
- DMA zone: 16863 pages, LIFO batch:3
- Normal zone: 0 pages used for memmap
- Built 1 zonelists. Total pages: 16863
- Kernel command line: console=ttyS0 mem=200M
- Primary instruction cache 32kB, 4-way, physically tagged, linesize 32 bytes.
- Primary data cache 32kB, 4-way, physically tagged, no aliases, linesize 32 bytes
- Synthesized TLB refill handler (20 instructions).
- Synthesized TLB load handler fastpath (32 instructions).
- Synthesized TLB store handler fastpath (32 instructions).
- Synthesized TLB modify handler fastpath (31 instructions).
- Cache parity protection disabled
- PID hash table entries: 2048 (order: 11, 8192 bytes)
- Using 357.750 MHz high precision timer.
- Console: colour dummy device 80x25
- Dentry cache hash table entries: 65536 (order: 4, 262144 bytes)
- Inode-cache hash table entries: 32768 (order: 3, 131072 bytes)
- Memory: 196144k/204800k available (3926k kernel code, 8432k reserved, 841k data, 2048k init, 0k highmem)
- Calibrating delay loop... 476.77 BogoMIPS (lpj=2383872)
- Mount-cache hash table entries: 2048
- NET: Registered protocol family 16
- PCI: pci host support disabled
- SCSI subsystem initialized
- libata version 2.21 loaded.
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- NET: Registered protocol family 2
- Time: TANGOX clocksource has been installed.
- IP route cache hash table entries: 4096 (order: 0, 16384 bytes)
- TCP established hash table entries: 16384 (order: 3, 131072 bytes)
- TCP bind hash table entries: 16384 (order: 2, 65536 bytes)
- TCP: Hash tables configured (established 16384 bind 16384)
- TCP reno registered
- cp0_timer: interrupt registered.
- SMP86xx zxenv (254:0): driver loaded.
- squashfs: version 3.4 (2008/08/26) Phillip Lougher
- NTFS driver 2.1.28 [Flags: R/O].
- fuse init (API version 7.8)
- yaffs built Feb 21 2012 10:53:50 Installing.
- io scheduler noop registered
- io scheduler anticipatory registered
- io scheduler deadline registered
- io scheduler cfq registered (default)
- console_peek registed.
- tango3dog: Hardware Watchdog Timer for SMP864x/SMP865x 0.1 (def. timeout: 30 sec)
- Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
- serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
- serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
- loop: module loaded
- tun: Universal TUN/TAP device driver, 1.6
- tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- tangox_enet0: ethernet mac_core 0 support is disabled from XENV
- tangox_enet1: detected phy at address 0x01
- tangox_enet1: Ethernet driver for SMP8xxx internal MAC core 1: 100Mbps Base at 0x26800
- tangox_enet1: mac address 00:90:a9:c7:24:51
- usbcore: registered new interface driver cdc_ether
- Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
- ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
- tangox_bmide: bmide support is disabled
- TangoX SATA support is disabled from XENV.
- [SMP_NAND] SMP8xxx NAND Driver 0.3 (multi-bits ECC: enabled)
- [SMP_NAND]: checking NAND device on CS0 ..
- NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
- Scanning device for bad blocks
- Bad eraseblock 3074 at 0x18040000
- Bad eraseblock 3197 at 0x18fa0000
- [SMP_NAND]: detected NAND on CS0, erasesize 131072, pagesize 2048, oobsize 64, oobavail 2
- [SMP_NAND]: checking NAND device on CS1 ..
- No NAND device found!!!
- [SMP_NAND]: detection completed, load partition information from XENV ..
- [SMP_NAND]: load partition information for CS0 ..
- Creating 10 MTD partitions on "NAND 512MiB 3,3V 8-bit":
- 0x00000000-0x00080000 : "bootblocks"
- 0x00080000-0x00180000 : "yamon"
- 0x00180000-0x00780000 : "kernel1"
- 0x00780000-0x00d80000 : "kernel2"
- 0x00d80000-0x01280000 : "xmat"
- 0x01280000-0x01c80000 : "imat"
- 0x01c80000-0x02180000 : "imat_failsafe"
- 0x02180000-0x0bf80000 : "system"
- 0x0bf80000-0x1fe00000 : "userdata"
- 0x1fe00000-0x20000000 : "static_config"
- ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
- USB Universal Host Controller Interface driver v3.0
- TangoX USB initializing...
- TangoX USB register base= 0x21700 0 = 0x0
- TangoX USB register base= 0x21700 1 = 0x202020
- TangoX USB register base= 0x21700 2 = 0x0
- TangoX USB register base= 0x21700 3 = 0xf9930
- tangox-ehci-hcd-0 tangox-ehci-hcd-0: TangoX USB 2.0
- tangox-ehci-hcd-0 tangox-ehci-hcd-0: new USB bus registered, assigned bus number 1
- tangox-ehci-hcd-0 tangox-ehci-hcd-0: irq 48, io mem 0xa0021500
- tangox-ehci-hcd-0 tangox-ehci-hcd-0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
- usb usb1: configuration #1 chosen from 1 choice
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- TangoX USB initializing...
- TangoX USB register base= 0x25700 0 = 0x0
- TangoX USB register base= 0x25700 1 = 0x202020
- TangoX USB register base= 0x25700 2 = 0x0
- TangoX USB register base= 0x25700 3 = 0xf9930
- tangox-ehci-hcd-1 tangox-ehci-hcd-1: TangoX USB 2.0
- tangox-ehci-hcd-1 tangox-ehci-hcd-1: new USB bus registered, assigned bus number 2
- tangox-ehci-hcd-1 tangox-ehci-hcd-1: irq 47, io mem 0xa0025500
- tangox-ehci-hcd-1 tangox-ehci-hcd-1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
- usb usb2: configuration #1 chosen from 1 choice
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 1 port detected
- usb 1-1: new high speed USB device using tangox-ehci-hcd-0 and address 2
- No OHCI in SMP8652/SMP8653/SMP8646/SMP8647/SMP8670.
- Initializing USB Mass Storage driver...
- usb 1-1: configuration #1 chosen from 1 choice
- hub 1-1:1.0: USB hub found
- hub 1-1:1.0: 4 ports detected
- usb 1-1.2: new high speed USB device using tangox-ehci-hcd-0 and address 3
- usb 1-1.2: configuration #1 chosen from 1 choice
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- Controller 0 is used in different mode.
- mice: PS/2 mouse device common for all mice
- usbcore: registered new interface driver hiddev
- usbcore: registered new interface driver usbhid
- drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
- Netfilter messages via NETLINK v0.30.
- IPv4 over IPv4 tunneling driver
- ip_tables: (C) 2000-2006 Netfilter Core Team
- TCP cubic registered
- NET: Registered protocol family 1
- NET: Registered protocol family 17
- ieee80211: 802.11 data/management/control stack, git-1.1.13
- ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
- ieee80211_crypt: registered algorithm 'NULL'
- Freeing unused kernel memory: 2048k freed
- ==================PRIMARY SYSTEM============================
- export SYSCONF_BUILD_DATE=2012.03.26-1742
- export SYSCONF_BUILD_VERSION=1.07.18
- export SYSCONF_NAND_DRIVER=MTD
- export SYSCONF_WDCM_ENABLE=ENABLE
- export SYSCONF_FIRMWARE_BIN=wdtvlivegen3.bin
- export SYSCONF_FIRMWARE_VER=wdtvlivegen3.ver
- export SYSCONF_BOOTLOADER_MTD_PARTITION=/dev/mtdblock1
- export SYSCONF_KERNEL_MTD_PARTITION=/dev/mtdblock3
- export SYSCONF_FIRMWARE_MTD_PARTITION=/system/rootfs/rootfs.bin
- export SYSCONF_FIRMWARE_MTD_SIZE=165675008
- export SYSCONF_FIRMWARE_STORAGE_PARTITION=/usrdata/rootfs/pkg.bin
- export SYSCONF_STORAGE_PARTITION_SIZE=336068608
- export SYSCONF_BOOT_AUTH=y
- export SYSCONF_FIRMWARE_FS=squashfs
- ============================================================
- Primary built date: 2012.03.26-1742
- MTD / YAFFS should be built in, no need to insmod
- SYSCONF_FIRMWARE_MTD_PARTITION = /system/rootfs/rootfs.bin
- FW_SIGN = sisi
- ===============================================================================
- ================ Boot from /system/rootfs/rootfs.bin ===================
- ====================================yaffs: dev is 32505864 name is "mtdblock8" rw
- ================yaffs: passed flags "inband-tags"
- ================yaffs: Attempting MTD mount of 31.8,"mtdblock8"
- ===========
- Mounting application firmware...
- Mount SYSTEM YAFFS
- mount -t yaffs2 -o inband-tags /dev/mtdblock8 /system
- yaffs: restored from checkpoint
- yaffs_read_super: is_checkpointed 1
- mount -o loop -t squashfs /system/rootfs/rootfs.bin /mnt/app_firmware/
- Application firmware mounted..
- Check the authentication of whole file..
- random_number = 2
- 256+0 records in
- 256+0 records out
- File /system/rootfs/rootfs.bin authenticated
- All files have been checked for their integrity...
- Launch application firmware...
- ===================ROOTFS===================================
- export SYSCONF_BUILD_DATE=2012.03.26-1742
- export SYSCONF_BUILD_VERSION=1.07.18
- export SYSCONF_NAND_DRIVER=MTD
- export SYSCONF_FIRMWARE_BIN=wdtvlivegen3.bin
- export SYSCONF_FIRMWARE_VER=wdtvlivegen3.ver
- export SYSCONF_BOOTLOADER_MTD_PARTITION=/dev/mtdblock1
- export SYSCONF_KERNEL_MTD_PARTITION=/dev/mtdblock3
- export SYSCONF_FIRMWARE_MTD_PARTITION=/system/rootfs/rootfs.bin
- export SYSCONF_FIRMWARE_MTD_SIZE=165675008
- export SYSCONF_WRITABLE_PARTITION_BLOCK_NAME=/dev/mtdblock9
- export SYSCONF_WRITABLE_PARTITION_CHARACTER_NAME=/dev/mtd9
- export SYSCONF_WRITABLE_PARTITION_MOUNT_POINT=/usrdata
- export SYSCONF_LAST_PARTITION_NODE_NAME=/dev/mtdblock10
- export SYSCONF_STATIC_CONFIG_MOUNT_POINT=/tmp/static_config
- export SYSCONF_LAST_PARTITION_CHARACTER_NAME=/dev/mtd10
- export SYSCONF_PRODUCT_EXT_WDTV_RV=y
- export IS_DTS=y
- export IS_DTCP=y
- export SYSCONF_LAST_PARTITION_IN_YAFFS2_FS=y
- ============================================================
- /init: line 24: gbus_read_serial_num: not found
- Launch dbus-launch.............
- hostname: can't open '/etc/hostname': No such file or directory
- /init: line 97: /sbin/ldconfig: not found
- df -k
- Filesystem 1k-blocks Used Available Use% Mounted on
- rootfs 118016 118016 0 100% /
- /dev/mtdblock8 118016 118016 0 100% /system
- /dev/loop0 118016 118016 0 100% /
- mdev 99200 0 99200 0% /dev
- none 99200 48 99152 0% /tmp
- /dev/mtdblock9 323584 17088 306496 5% /usrdata
- /usrdata/User.chk: OK
- UserDataBlock Work(Check md5sum Success..!!)
- tmp (ramdisk) used (total checked by df) is : 99152 kB
- usrdata used (total checked by df) is : 17088 kB
- usrdata used (real checked by du) is : 15459 kB
- usrdata used (unknow) : 1629 kB
- OK: usrdata unknown space is ok
- ============== UserDataCheck.sh done ======================
- F:mkconfig_translate_file_to_config_dir,392: [load config] ret_config=0, i_filename_mirror=/usrdata/cfg/config2
- (./src/securesoho/config_tool.c, 316), /tmp/drm do not exist, try create it.
- There is no backup files.
- F:ep_fifo_create_cb:106, readfd:3
- flash_monitor_add_task,423, add a new task(/tmp/conf/,/usrdata/cfg/config1)
- flash_monitor_add_task,423, add a new task(/tmp/drm,(null))
- /tmp/static_config/SConfig.chk: OK
- StaticConfigBlock Work(Check md5sum Success..!!)
- check static config workaround for Palace only
- / /
- /
- Loading llad.ko
- Chip identified as SMP8670 prod (certificate id 0x1c, t3iptv family)
- Loading llad.ko
- //bin/xkc
- Unloading ios
- Stopping audio0... OK
- Stopping audio1... FAILED
- Stopping audio2... FAILED
- Stopping video0... OK
- Stopping video1... FAILED
- Stopping demux0... OK
- Stopping demux1... FAILED
- Unloading of demuxpsf ucode... FAILED
- Unloading of audio ucode... FAILED
- Unloading of video ucode... FAILED
- Using scratch=0x9ddbf768
- Loading video ucode
- Loading audio ucode
- Loading demuxpsf ucode
- Starting DTCP_IP xtask
- Starting demux0
- Starting demux1
- starting demux1 failed. 864x, 8652, 8670 have no demux1.
- Starting video0
- Starting video1
- starting video1 failed. 8652, 8654, 8670 have no video1.
- Starting audio0
- Starting audio1
- starting audio1 failed. 8652, 8654, 8670 have no audio1.
- Starting audio2
- starting audio2 failed. 8652, 8654, 8670 have no audio2.
- //bin/genxenv2
- //bin/gbus_read_bin_to_file
- To ga=0x9ee00000
- demux0 is alive
- audio0 is alive
- mpeg0 is alive
- ipu is alive
- ih is alive
- firmware reload successful
- modprobe: module r8169 not found
- modprobe: failed to load module r8169
- insmod: cannot insert '/lib/modules/irkernel.ko': Device or resource busy
- insmod: cannot insert '/lib/modules/irkernel.ko': Device or resource busy
- insmod: cannot insert '/lib/modules/irkernel.ko': Device or resource busy
- insmod: cannot insert '/lib/modules/thermal_g751.ko': Operation not permitted
- insmod: cannot insert '/lib/modules/wdtv_rv_microp.ko': Device or resource busy
- insmod: cannot insert '/lib/modules/wdtv_rv_microp.ko': Device or resource busy
- insmod: cannot insert '/lib/modules/wdtv_rv_microp.ko': Device or resource busy
- insmod: cannot insert '/lib/modules/wdtv_rv_microp.ko': Device or resource busy
- Try to set time from RTC to system
- rtc time : Mon Nov 4 06:07:07 2002
- HDMI
- auto
- get_analog_signal,26
- NTSC
- string_set_to_file,303
- dstd=hdtv60, dsg=edid, ang=ntsc, com_sg=720p
- string_set: [auto], changed
- /init: line 332: gbus_read_serial_num: not found
- enter si test ...
- mount: mounting /dev/sda1 on /tmp/media/usb failed: No such device or address
- Mounting /dev/sda1 fail, try to mount /dev/sda to /tmp/media/usb
- mount: mounting /dev/sda on /tmp/media/usb failed: No such file or directory
- Mounting /dev/sda still fail, abort!!!
- /tmp/media/usb/runsit.sh is not exist...
- umount: cannot umount /tmp/media/usb: Invalid argument
- mount: mounting /dev/sdb1 on /tmp/media/usb failed: No such file or directory
- Mounting /dev/sdb1 fail, try to mount /dev/sdb to /tmp/media/usb
- mount: mounting /dev/sdb on /tmp/media/usb failed: No such file or directory
- Mounting /dev/sdb still fail, abort!!!
- /init: lin
- Sigma Designs SMP863x development environment (based on the buildroot project)
- (none) login:
Add Comment
Please, Sign In to add comment